CISCO-VOICE-ANALOG-IF-MIB Table View

The Analog Voice Standard Configuration Table. It contains 
the standard configuration information of the analog          
telephony interface.

cvaIfCfgEntry row .1.3.6.1.4.1.9.9.62.1.1.1.1

An entry in the configuration table for each voice analog
interface. The entry is created when the voice analog
hardware is detected.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cvaIfCfgImpedance Specifies the terminating impedance of voice analog interfaces. other - none of the following; arbitrary, within limits, for special cases. ohms600Real - 600 Ohms. ohms600Complex - 600 Ohms …	Enumerationr/w Enumerated Values: 1 other 2 ohms600Real 3 ohms600Complex 4 ohms900Complex 5 ohmsComplex1 6 ohmsComplex2	.1.3.6.1.4.1.9.9.62.1.1.1.1.1
cvaIfCfgIntegratedDSP Indicates whether the interface has an integrated Digital Signal processing (DSP) unit.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.1.1.1.2

The Analog Voice Status Table.  It contains general 
information about the status of Analog Telephony interface
including the error statistics.

cvaIfStatusEntry row .1.3.6.1.4.1.9.9.62.1.1.2.1

An entry in the status table for each Analog voice interface.

Indexes

No indexes recorded

Column	Syntax	OID
cvaIfStatusInfoType The information transfer services for the current or last call. none - no information transfer service voice - analog voice. g3Fax - Group 3 FAX.	Enumeration Enumerated Values: 1 none 2 voice 3 g3Fax	.1.3.6.1.4.1.9.9.62.1.1.2.1.1
cvaIfMaintenanceMode Indicates the maintenance modes of the Analog voice interface. Managed system +=============+=============================+ | Voice | +===========+ telephony | <=====+ application +===+ CODEC …	Enumeration Enumerated Values: 1 none 2 hostCompressedLoopback 3 hostUncompressedLoopback 4 ifCompressedLoopback 5 ifUncompressedLoopback	.1.3.6.1.4.1.9.9.62.1.1.2.1.2
cvaIfStatusSignalErrors Accumulated number of signaling protocol errors that are detected in the interface since system startup.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.62.1.1.2.1.3

The E&M standard configuration table. It contains 
the current setting of E&M configurable parameters.

cvaIfEMCfgEntry row .1.3.6.1.4.1.9.9.62.1.2.1.1

An entry in the standard configuration table for
each E&M tie trunk interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cvaIfEMCfgSignalType The signaling type of E&M tie trunk interface. winkStart - the calling side seizes the line by going off-hook on its E lead but waits for a short off-hook 'wink' indication on its M lead from …	Enumerationr/w Enumerated Values: 1 winkStart 2 immediateDial 3 delayDial 4 lmr 5 fgd 6 fgd-eana	.1.3.6.1.4.1.9.9.62.1.2.1.1.1
cvaIfEMCfgOperation Specify the operation of the E&M signal. twoWires - 2-wire operation. fourWires - 4-wire operation.	Enumerationr/w Enumerated Values: 1 twoWires 2 fourWires	.1.3.6.1.4.1.9.9.62.1.2.1.1.2
cvaIfEMCfgType Specifies the E&M Lead Signaling type. LEGEND: V = -48V /\/\/ = detector/resister X = normally open relay contact + = normally closed relay contact G = ground SB = Signal Battery SG = Signal Ground…	Enumerationr/w Enumerated Values: 1 typeI 2 typeII 3 typeIII 4 typeIV 5 typeV	.1.3.6.1.4.1.9.9.62.1.2.1.1.3
cvaIfEMCfgDialType Specifies the out dialing type of E&M interface.	InterfaceDialTyper/w Type Values: 1 dtmf 2 pulse 3 mf	.1.3.6.1.4.1.9.9.62.1.2.1.1.4
cvaIfEMCfgLmrMCap The M lead behavior of E&M LMR interface. inact - The m-lead status should be ignored. audio - The m-lead status is used to control generating voice packet. dial - Perform the same audio case except abling to …	Enumerationr/w Enumerated Values: 1 inact 2 audio 3 dial	.1.3.6.1.4.1.9.9.62.1.2.1.1.5
cvaIfEMCfgLmrECap The E lead behavior of E&M LMR interface. seize - The e-lead used as seize signal voice - The e-lead status is used to indicate voice packet received or not. inactive -- e-lead is inactive.	Enumerationr/w Enumerated Values: 4 seize 5 voice 6 inactive	.1.3.6.1.4.1.9.9.62.1.2.1.1.6
cvaIfEMCfgAutoGainControl This object is used to enabling/disabling automatic gain control(AGC) on this interface. AGC allows DSP to adjust the input voice volume and avoid rapid voice volume change.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.2.1.1.7

The E&M interface Table.  The table contains 
the status of the E&M tie trunk interface.

cvaIfEMStatusEntry row .1.3.6.1.4.1.9.9.62.1.2.2.1

An entry in the status table for each E&M interface.

Indexes

No indexes recorded

Column	Syntax	OID
cvaIfEMInSeizureActive This object contains the incoming seizure state of the E&M interface. If the value is true, then the interface has an incoming trunk seizure active; otherwise, it doesn't.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.2.2.1.1
cvaIfEMOutSeizureActive This object contains the outgoing seizure state of the E&M interface. If the value is true, then the interface has an outgoing trunk seizure active; otherwise, it doesn't.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.2.2.1.2

The E&M tie trunk Timing Parameters table. It 
contains the configuration of the various E&M signaling
protocol timing parameters.

cvaIfEMTimingEntry row .1.3.6.1.4.1.9.9.62.1.2.3.1

An entry in the E&M Timing Parameters Table for
each E&M interface.

Indexes

No indexes recorded

Column	Syntax	OID
cvaIfEMTimingDigitDuration Outgoing DTMF digit duration in milliseconds.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.9.9.62.1.2.3.1.1
cvaIfEMTimingInterDigitDuration Outgoing DTMF inter-digit duration in milliseconds.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.9.9.62.1.2.3.1.2
cvaIfEMTimingPulseRate Outgoing pulse dialing rate in pulses per second (pps).	pulses per secondInteger32r/w Constraints: range: 10-20	.1.3.6.1.4.1.9.9.62.1.2.3.1.3
cvaIfEMTimingPulseInterDigitDuration Outgoing Pulse dialing inter-digit timing in milliseconds.	millisecondsInteger32r/w Constraints: range: 100-1000	.1.3.6.1.4.1.9.9.62.1.2.3.1.4
cvaIfEMTimingClearWaitDuration Time of Inactive seizure signal to declare call cleared.	millisecondsInteger32r/w Constraints: range: 200-2000	.1.3.6.1.4.1.9.9.62.1.2.3.1.5
cvaIfEMTimingMaxWinkWaitDuration Maximum time to wait from the outgoing seizure of the line to the time of sending out a wink-pulse.	millisecondsInteger32r/w Constraints: range: 100-5000	.1.3.6.1.4.1.9.9.62.1.2.3.1.6
cvaIfEMTimingMaxWinkDuration Maximum outgoing wink duration (between the wink-pulse leading edge and trailing edge) for wink start signaling.	millisecondsInteger32r/w Constraints: range: 100-3000	.1.3.6.1.4.1.9.9.62.1.2.3.1.7
cvaIfEMTimingDelayStart Minimum time to wait from outgoing seizure to out-dialing digits for delay start signaling.	millisecondsInteger32r/w Constraints: range: 20-2000	.1.3.6.1.4.1.9.9.62.1.2.3.1.8
cvaIfEMTimingMaxDelayDuration Maximum time to wait from outgoing seizure to out-dialing digits. If the far end does not allow to send digits after the duration specified in the object, a reorder tone will be sent to the calling party.	millisecondsInteger32r/w Constraints: range: 100-5000	.1.3.6.1.4.1.9.9.62.1.2.3.1.9
cvaIfEMTimingMinDelayPulseWidth Minimum delay-dial pulse duration for incoming call. If the value of this object is 0, then no delay-dial is sent to the far end for the incoming call.	millisecondsInteger32r/w Constraints: range: 140-5000 range: 0-0	.1.3.6.1.4.1.9.9.62.1.2.3.1.10
cvaIfEMTimingVoiceHangover The hangover time used to determine the casethere is no more voice packet arrived.	millisecondsInteger32r/w Constraints: range: 0-10000	.1.3.6.1.4.1.9.9.62.1.2.3.1.11
cvaIfEMTimeoutLmrTeardown LMR port tear down timeout. This object is relevant to the waiting time of teardown call on LMR port. if the value of this object is '-1', then the timeout is disable.	secondsInteger32r/w Constraints: range: -1--1 range: 5-60000	.1.3.6.1.4.1.9.9.62.1.2.3.1.12
cvaIfEMTimeoutPttXmt This object signifies LMR port maxinum transmit time. This object is relevant to how long LMR port can continue transmit voice packet without pause.	minutesInteger32r/w Constraints: range: 0-30	.1.3.6.1.4.1.9.9.62.1.2.3.1.13
cvaIfEMTimeoutPttRcv This object signifies LMR port maxinum receive time. This object is relevant to how long LMR port can continue receive voice packet without pause.	minutesInteger32r/w Constraints: range: 0-30	.1.3.6.1.4.1.9.9.62.1.2.3.1.14
cvaIfEMTimingDelayVoice This object is relevant to how long DSP will delay sending the voice packet to the LMR port.	millisecondsInteger32r/w Constraints: range: 0-1500	.1.3.6.1.4.1.9.9.62.1.2.3.1.15

The FXO standard configuration table. It contains 
FXO configuration parameters, one entry per FXO interface.
The configuration information of this table is set by 
hardware with its default setting or CLI during the hardware 
installation time.

cvaIfFXOCfgEntry row .1.3.6.1.4.1.9.9.62.1.3.1.1

An entry in the standard configuration table for
each FXO interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cvaIfFXOCfgSignalType the signaling type of FXO interface. fxoLoopStart - loop start. fxoGroundStart - ground start. fxoCama - cama.	Enumerationr/w Enumerated Values: 1 fxoLoopStart 2 fxoGroundStart 3 fxoCama	.1.3.6.1.4.1.9.9.62.1.3.1.1.1
cvaIfFXOCfgNumberRings The number of rings detected before closing loop.	ringsInteger32r/w Constraints: range: 1-10	.1.3.6.1.4.1.9.9.62.1.3.1.1.2
cvaIfFXOCfgSupDisconnectdeprecated Specifies whether a supervisory disconnect signal (CPC) will be presented to the interface when the connected party at the interface hangs up.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.3.1.1.3
cvaIfFXOCfgDialType Specifies the out dialing type of FXO interface.	InterfaceDialTyper/w Type Values: 1 dtmf 2 pulse 3 mf	.1.3.6.1.4.1.9.9.62.1.3.1.1.4
cvaIfFXOCfgSupDisconnect2 Specifies the type of supervisory disconnect signal (CPC) to be presented to the interface when the connected party at the interface hangs up. signal - power denial recognition anytone - tone detection of all call pro…	Enumerationr/w Enumerated Values: 0 signal 1 anytone 2 dualtoneMidcall 3 dualtonePreconnect	.1.3.6.1.4.1.9.9.62.1.3.1.1.5

The Foreign Exchange Office (FXO) interface Status Table.
It contains hook status, ring detection and other states of
the interface.

cvaIfFXOStatusEntry row .1.3.6.1.4.1.9.9.62.1.3.2.1

An entry in the status table for each FXO interface.

Indexes

No indexes recorded

Column	Syntax	OID
cvaIfFXOHookStatus This object contains the hook status of FXO interface. onHook - Present the onHook to the connected equipment. offHook - Present the offHook to the connected equipment. trunked - Present the trunk to the connected equi…	Enumeration Enumerated Values: 1 onHook 2 offHook 3 trunked	.1.3.6.1.4.1.9.9.62.1.3.2.1.1
cvaIfFXORingDetect This object contains the ring detect indication. If the value is true, then the interface detects ring from PBX or CO; otherwise, it doesn't.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.3.2.1.2
cvaIfFXORingGround This object contains the incoming ring ground indication. It is only valid when the cvaIfFXOCfgSignalType is fxoGroundStart. If the object is true, then the interface is presenting a ring ground to the connected equipm…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.3.2.1.3
cvaIfFXOTipGround This object contains the incoming tip ground indication. It is only valid when the cvaIfFXOCfgSignalType is fxoGroundStart. If the object is true, then the interface is detecting a tip ground at the interface; otherwis…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.3.2.1.4

The FXO interface Timing Parameters table. It 
contains the configuration of the various FXO signaling
protocol timing parameters.

cvaIfFXOTimingEntry row .1.3.6.1.4.1.9.9.62.1.3.3.1

An entry in the FXO Timing Parameters Table for
each FXO interface.

Indexes

No indexes recorded

Column	Syntax	OID
cvaIfFXOTimingDigitDuration Outgoing DTMF digit duration in milliseconds.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.9.9.62.1.3.3.1.1
cvaIfFXOTimingInterDigitDuration Outgoing DTMF inter-digit duration in milliseconds.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.9.9.62.1.3.3.1.2
cvaIfFXOTimingPulseRate Outgoing pulse dialing rate in pulses per second (pps).	pulses per secondInteger32r/w Constraints: range: 10-20	.1.3.6.1.4.1.9.9.62.1.3.3.1.3
cvaIfFXOTimingPulseInterDigitDuration Outgoing pulse dialing inter-digit timing in milliseconds.	millisecondsInteger32r/w Constraints: range: 100-1000	.1.3.6.1.4.1.9.9.62.1.3.3.1.4

The FXS standard configuration table. It contains
FXS configuration parameters, one entry per FXS interface.
The configuration information of this table is set by 
hardware with its default setting or CLI during the hardware 
installation time.

cvaIfFXSCfgEntry row .1.3.6.1.4.1.9.9.62.1.4.1.1

An entry in the standard configuration table for
each FXS interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cvaIfFXSCfgSignalType the signaling type of FXS interface. fxsLoopStart - loop start. fxsGroundStart - ground start.	Enumerationr/w Enumerated Values: 1 fxsLoopStart 2 fxsGroundStart	.1.3.6.1.4.1.9.9.62.1.4.1.1.1
cvaIfFXSRingFrequency the ring frequency to be used in the FXS interface. ringFrequency25 - ring frequency 25 Hertz. ringFrequency50 - ring frequency 50 Hertz. ringFrequency20 - ring frequency 20 Hertz. ringFrequency30 - ring frequency …	Enumerationr/w Enumerated Values: 1 ringFrequency25 2 ringFrequency50 3 ringFrequency20 4 ringFrequency30	.1.3.6.1.4.1.9.9.62.1.4.1.1.2

The Foreign Exchange Station (FXS) interface Status Table.
It contains hook status, ring active and other states of
the interface.

cvaIfFXSStatusEntry row .1.3.6.1.4.1.9.9.62.1.4.2.1

An entry in the status table for each FXS interface.

Indexes

No indexes recorded

Column	Syntax	OID
cvaIfFXSHookStatus This object contains the hook status of FXS interface. onHook - the connected equipment(e.g., phone) is onHook. offHook - the connected equipment is offHook. trunked - the connected equipment is trunked.	Enumeration Enumerated Values: 1 onHook 2 offHook 3 trunked	.1.3.6.1.4.1.9.9.62.1.4.2.1.1
cvaIfFXSRingActive This object contains the outgoing ring active indication. If the object value is true, then the interface is currently generating ring out to the Key Telephone System (KTS) or Plain Old Telephone (POT); otherwise, it d…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.4.2.1.2
cvaIfFXSRingGround This object contains the incoming ring ground indication. It is only valid when the cvaIfFXSCfgSignalType is fxsGroundStart. If the object is true, then the interface is presenting a ring ground to the connected equipm…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.4.2.1.3
cvaIfFXSTipGround This object contains the incoming tip ground indication. It is only valid when the cvaIfFXSCfgSignalType is fxsGroundStart. If the object is true, then the interface is detecting a tip ground at the interface; otherwis…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.62.1.4.2.1.4

The FXS interface Timing Parameters table. It 
contains the configuration of the various FXS signaling
protocol timing parameters.

cvaIfFXSTimingEntry row .1.3.6.1.4.1.9.9.62.1.4.3.1

An entry in the FXS Timing Parameters Table for
each FXS interface.

Indexes

No indexes recorded

Column	Syntax	OID
cvaIfFXSTimingDigitDuration Outgoing DTMF digit duration in milliseconds.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.9.9.62.1.4.3.1.1
cvaIfFXSTimingInterDigitDuration Outgoing DTMF inter-digit duration in milliseconds.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.9.9.62.1.4.3.1.2