CISCO-TS-STACK-MIB Table View

Trap Receiver Table for each TrBRF.

ciscoTsTrapRcvrEntry row .1.3.6.1.4.1.9.5.32.1.1.25.1

Definition of each row in the TrBRF specific trap
receiver table.

Indexes

ciscoTsTrapRcvrIndex

Column	Syntax	OID
ciscoTsTrapRcvrIndexmandatory Trap receiver index for each entry. The switch only allows 20 entries into this table.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.9.5.32.1.1.25.1.1
ciscoTsTrapRcvrStatusmandatory Setting the value of this object to invalid(3) deletes the row from the table. The value invalid(3) should never be returned on a GET. Setting this value to create(4) causes a new row to be created if …	Enumerationr/w Enumerated Values: 1 other 2 valid 3 invalid 4 create	.1.3.6.1.4.1.9.5.32.1.1.25.1.2
ciscoTsTrapRcvrIpAddressmandatory IP address for an SNMP manager that is to receive the trap.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.9.5.32.1.1.25.1.3
ciscoTsTrapRcvrCommmandatory Community string to use in outgoing traps.	OctetStringr/w Constraints: range: 1-16	.1.3.6.1.4.1.9.5.32.1.1.25.1.4
ciscoTsTrapRcvrTrBRFsmandatory TrBRFs on which traps to this target are sent. Each octet within the value of this object specifies a set of eight TrBRFs, with the first octet specifying TrBRFs 1 through 8, the second octet specifying TrBRFs 9 thro…	OctetStringr/w Constraints: range: 128-128	.1.3.6.1.4.1.9.5.32.1.1.25.1.5

Stack information table. This table provides
the current configuration of the stack. It also
provides a mapping of Switch Numbers to their 
addresses.  There is one entry in this table
for each switch in the stack.  Entries cannot
be administratively created/deleted.
          
The Management Application is required to retrieve this
table and verify its own view of the stack periodically
and/or when it receives a trap indicating a change in the 
 stack configuration.

ciscoTsStackEntry row .1.3.6.1.4.1.9.5.32.2.1.1

Definition of each row in the Stack Table

Indexes

ciscoTsStackSwitchNumber ciscoTsStackSwitchBIAddr

Column	Syntax	OID
ciscoTsStackSwitchNumbermandatory Switch number as determined by the port number that the switch is connected to in a Matrix or as determined by the Stack Management software when two switches are connected back to back.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.9.5.32.2.1.1.1
ciscoTsStackSwitchBIAddrmandatory The burned in MAC address of the switch.	MacAddr Type Constraints: range: 6	.1.3.6.1.4.1.9.5.32.2.1.1.2
ciscoTsStackSwitchLAAddrmandatory The locally administered MAC address of the switch. After writing to this object, you must reset the switch.	MacAddrr/w Type Constraints: range: 6	.1.3.6.1.4.1.9.5.32.2.1.1.3
ciscoTsStackSwitchFwVersionmandatory Version number for the firmware running on the switch.	OctetString Constraints: range: 1-128	.1.3.6.1.4.1.9.5.32.2.1.1.4
ciscoTsStackSwitchHwVersionmandatory Hardware version number for the switch.	OctetString Constraints: range: 1-128	.1.3.6.1.4.1.9.5.32.2.1.1.5
ciscoTsStackSwitchUptimemandatory Time ticks since the switch was last reset.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.6
ciscoTsStackSwitchStatusmandatory Operational status of the box. Setting this value to either coldReset(2) or warmReset(3) will cause cold start or warm start to occur after a predefined time delay.	Enumerationr/w Enumerated Values: 1 running 2 coldReset 3 warmReset	.1.3.6.1.4.1.9.5.32.2.1.1.7
ciscoTsStackSwitchTemperaturemandatory Temperature of each switch reported in degrees Celsius.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.5.32.2.1.1.8
ciscoTsStackSwitchMemorymandatory Installed memory on the switch in MB.	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.9.5.32.2.1.1.9
ciscoTsStackSwitchSPANPortmandatory Port number to be used for the Switch Port Analyzer. Setting this object to zero turns off the SPAN function.	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.9.5.32.2.1.1.10
ciscoTsStackSwitchSPANMonitoredPortmandatory Port monitored by the SPAN function.	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.9.5.32.2.1.1.11
ciscoTsStackSwitchFeatureStatusmandatory This object indicates whether the switch is enabled to support enhanced features.	Enumeration Enumerated Values: 1 standard 2 enhanced 3 unknown	.1.3.6.1.4.1.9.5.32.2.1.1.12
ciscoTsStackSwitchFeatureKeymandatory Feature key to enable enhanced features. See the manual for information pertaining to enabling possible enhanced features.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.5.32.2.1.1.13
ciscoTsStackSwitchPortsmandatory A bit mask representing all the ports present in this switch. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying …	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.9.5.32.2.1.1.14
ciscoTsStackSwitchAgingTimemandatory Aging time in minutes for the master address table entries on this switch.	Integer32r/w Constraints: range: 0-9999	.1.3.6.1.4.1.9.5.32.2.1.1.15
ciscoTsStackSwitchAgingLevelmandatory Threshold to demand age the master address table. All numbers refer to percentage of the address table. The only values accepted by the agent are 50,60,70,80,90 and 0. Setting the value to 0 disables demand aging.	Integer32r/w Constraints: range: 0-90	.1.3.6.1.4.1.9.5.32.2.1.1.16
ciscoTsStackSwitchXmitFramesmandatory Frames transmitted by the CPU.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.18
ciscoTsStackSwitchRcvdFramesmandatory Frames received for processing by the CPU.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.19
ciscoTsStackSwitchRcvdErrFramesmandatory Error frames received by the CPU.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.20
ciscoTsStackSwitchLostFramesmandatory Frames lost by the CPU while trying to transmit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.21
ciscoTsStackSwitchPendingSendRqstsmandatory Frames queued in the CPU's transmit buffer.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.22
ciscoTsStackSwitchXmitErrFramesmandatory Frames in error due to buffer overflows or drops in the CPU.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.23
ciscoTsStackSwitchCurrActStationsmandatory The number of station address entries currently active in the switch.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.24
ciscoTsStackSwitchLargestNumStationsmandatory The largest number of active stations ever seen on the switch since the last reboot, or clearing of statistics.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.25
ciscoTsStackSwitchMaxAddressChainmandatory The longest chain of addresses anywhere in the CPU's address hash table.		.1.3.6.1.4.1.9.5.32.2.1.1.26
ciscoTsStackSwitchAddressTblFullsmandatory The number of times a hash table chain has filled up.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.2.1.1.27
ciscoTsStackSwitchIdmandatory The object ID used to uniquely identify the type of Cisco token ring switch.	ObjectIdentifier	.1.3.6.1.4.1.9.5.32.2.1.1.28
ciscoTsStackSwitchSPANMonitoredTrCRFsmandatory Token Ring Concentrator Facilities (TrCRFs) for which traffic on the port specified by ciscoTsStackSwitchSPANMonitoredPort should be monitored. Individual TrCRFs can be selected for monitoring only on trunk ports. …	OctetStringr/w Constraints: range: 128-128	.1.3.6.1.4.1.9.5.32.2.1.1.29
ciscoTsStackSwitchPwrSupplyStatusmandatory The status of the power supply of the switch. The values have the following meanings: unknown(1) : The status is not known. internal-only(2) : The switch is not capable of redundant power…	Enumeration Enumerated Values: 1 unknown 2 internal-only 3 internal-no-backup 4 internal-backup-will-reset 5 external-no-backup 6 external-backup-no-reset	.1.3.6.1.4.1.9.5.32.2.1.1.30

Module configuration table.  There is one entry
in the table for each module in a stack.
Entries cannot be administratively created/deleted.

ciscoTsModEntry row .1.3.6.1.4.1.9.5.32.3.1.1

Definition of each row in the Module Table

Indexes

ciscoTsModSwitchNumber ciscoTsModNumber

Column	Syntax	OID
ciscoTsModSwitchNumbermandatory Switch number as determined by the port number that the switch is connected to in a Matrix or as determined by the Stack Management software when two switches are connected back to back.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.9.5.32.3.1.1.1
ciscoTsModNumbermandatory The module number.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.9.5.32.3.1.1.2
ciscoTsModStatemandatory The state indicates the current operational state of the module.	Enumeration Enumerated Values: 1 nomodule 2 running 3 faulty	.1.3.6.1.4.1.9.5.32.3.1.1.3
ciscoTsModTypemandatory The type of module plugged in to the slot. Module type system(1) represents the mother board with the CPU and system memory. Module state none(10) represents a slot with no modules plugged in (indicated by ciscoTsModS…	Enumeration Enumerated Values: 1 system 2 proStack 3 proPort4TR 4 proPort4Fiber 5 proPortISL-FX 6 proPortISL-TX 8 proPortATM155Fiber 9 proPortATM155UTP 10 unknown 11 none	.1.3.6.1.4.1.9.5.32.3.1.1.4
ciscoTsModRevisionmandatory The module revision number.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.9.5.32.3.1.1.5
ciscoTsModFwVermandatory The module's firmware version.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.9.5.32.3.1.1.6
ciscoTsModNumPortsmandatory Total number of ports in the module.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.5.32.3.1.1.7
ciscoTsModUptimemandatory Time ticks since the module was last reset.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.3.1.1.8

A table of configuration information about each port.
There is one entry for each port in a stack.  Entries
cannot be administratively created/deleted.

ciscoTsPortCfgEntry row .1.3.6.1.4.1.9.5.32.4.1.1

Definition of rows in the port configuration table.

Indexes

ciscoTsStackSwitchNumber ciscoTsPortCfgNumber

Column	Syntax	OID
ciscoTsPortCfgNumbermandatory A unique value for each port entry. The value corresponds the port number.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.9.5.32.4.1.1.1
ciscoTsPortCfgModNumbermandatory Module number of the module that contains this port.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.9.5.32.4.1.1.2
ciscoTsPortCfgIfIndexmandatory A pointer to the entry in the ifTable corresponding to this port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.5.32.4.1.1.3
ciscoTsPortCfgResetStatsmandatory Setting this object to reset(3) causes all traffic counters for this port to be set to zero. Also the value of ciscoTsPortStatsResetTimer is set to zero.	Enumerationr/w Enumerated Values: 1 other 2 running 3 reset	.1.3.6.1.4.1.9.5.32.4.1.1.4
ciscoTsPortCfgResetAddrsmandatory Setting this object to reset(3) clears all address table entries for this port as well as setting all port traffic counters to zero and setting ciscoTsPortStatsResetTimer to zero.	Enumerationr/w Enumerated Values: 1 other 2 running 3 reset	.1.3.6.1.4.1.9.5.32.4.1.1.5
ciscoTsPortCfgAddrAgingTimemandatory Port level address aging time in minutes. Setting this object to zero disables address aging.	Integer32r/w Constraints: range: 0-9999	.1.3.6.1.4.1.9.5.32.4.1.1.6
ciscoTsPortCfgDemandAgingLevelmandatory Threshold to demand age the port address table. All numbers refer to percentage of the address table. The only values accepted by the agent are 50,60,70,80,90 and 0. Setting the value to 0 disables demand aging.	Integer32r/w Constraints: range: 0-90	.1.3.6.1.4.1.9.5.32.4.1.1.7
ciscoTsPortCfgErrLoThresholdmandatory Lower error rate threshold which causes the port to transition from store and forward mode to cut-through mode.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.9.5.32.4.1.1.8
ciscoTsPortCfgErrHiThresholdmandatory Upper error rate threshold which causes the port to transition from cut-through mode to store and forward mode.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.9.5.32.4.1.1.9
ciscoTsPortCfgErrSamplingmandatory Error sampling interval in minutes.	Integer32r/w Constraints: range: 0-60	.1.3.6.1.4.1.9.5.32.4.1.1.10
ciscoTsPortCfgMaxTransmitUnitmandatory MTU size. The valid values for this object are 1500, 4472, 8144 and 17800. The value specified cannot exceed the vtpVlanMTU (see Cisco VTP MIB) for the TrBRF that this port is a member of. Set requests for invalid va…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.5.32.4.1.1.11
ciscoTsPortCfgMaxExplorerRatemandatory Explorer frame forwarding rate per second throttle. A value of (-1) disables explorer frame throttling.	Integer32r/w Constraints: range: -1-5000	.1.3.6.1.4.1.9.5.32.4.1.1.12
ciscoTsPortCfgSetACbitsmandatory Specifies if the AC bits shall be set unconditionally when a port forwards certain LLC frames.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.9.5.32.4.1.1.13
ciscoTsPortCfgEarlyTokenRlsemandatory Early token release operation.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.9.5.32.4.1.1.14
ciscoTsPortCfgForwardingModemandatory Operational frame switching mode for the port. When in auto mode the port uses the Direct Cut algorithm to place the port in either cutthru(3) or storeandforward(2) mode.	Enumerationr/w Enumerated Values: 1 auto 2 storeandforward 3 cutthru 4 unknown	.1.3.6.1.4.1.9.5.32.4.1.1.15
ciscoTsPortCfgActualForwardingModemandatory Actual operational frame switching mode for the port.	Enumeration Enumerated Values: 1 storeandforward 2 cutthru 3 unknown	.1.3.6.1.4.1.9.5.32.4.1.1.16
ciscoTsPortCfgPortModemandatory Port operation mode. Only the HDX and FDX modes can be auto detected. Note, that passive-probe(7) mode can not be set with this object. The passive-probe(7) mode is set automatically when a passive probe is defined in …	Enumerationr/w Enumerated Values: 1 auto 2 hdx-Port 3 hdx-Station 4 fdx-Port 5 fdx-Station 6 ri-ro 7 passive-probe 8 unknown	.1.3.6.1.4.1.9.5.32.4.1.1.17
ciscoTsPortCfgActualPortModemandatory The actual port operation mode. If the port is in auto mode, this object will return the mode that the port opened in.	Enumeration Enumerated Values: 1 hdx-Port 2 hdx-Station 3 fdx-Port 4 fdx-Station 5 ri-ro 6 passive-probe 7 unknown	.1.3.6.1.4.1.9.5.32.4.1.1.18
ciscoTsPortCfgPriorityThresmandatory The highest token-ring frame priority that shall go to the low-priority transmit queue.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.9.5.32.4.1.1.19
ciscoTsPortCfgMinXmitPrioritymandatory The minimum token priority that will be used for transmit.	Integer32r/w Constraints: range: 0-6	.1.3.6.1.4.1.9.5.32.4.1.1.20
ciscoTsPortCfgCfgLossThresmandatory Number of configuration loss events (described in TsPortCfgLossRC) during the sample period which, if exceeded, should cause the port to be disabled. If the port is disabled by this function the port must be manually re…	Integer32r/w Constraints: range: 1-100	.1.3.6.1.4.1.9.5.32.4.1.1.21
ciscoTsPortCfgCfgLossIntervalmandatory The sampling period, in minutes, for which the port monitors to determine if the configuration loss threshold has been exceeded.	Integer32r/w Constraints: range: 1-60	.1.3.6.1.4.1.9.5.32.4.1.1.22
ciscoTsPortCfgBcastSuppresionmandatory The number of broadcast frames per second allowed to be forwarded by this port. Any broadcast frames exceeding this watermark will not be forwarded by the port. Setting this object to 0 turns broadcast suppression off.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.9.5.32.4.1.1.23
ciscoTsPortCfgCDPTimeToLivemandatory The advertised time-to-live parameter on all CDP messages generated by this switch on this port.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.9.5.32.4.1.1.24
ciscoTsPortCfgSpanningTreeModemandatory Used when configuring manual spanning tree. Setting this object to forwarding(2) or blocking(3) overrides the TrCRF's spanning tree's algorithm for this port.	Enumerationr/w Enumerated Values: 1 auto 2 forwarding 3 blocking 4 unknown	.1.3.6.1.4.1.9.5.32.4.1.1.25
ciscoTsPortCfgSecurityModemandatory Port security mode is used to disable address learning at a port where an allow-source or allow-destination MAC address filter is configured. A value of normal(1) indicates that the port is not configured for security.…	Enumerationr/w Enumerated Values: 1 normal 2 secure-src-addrs 3 secure-dest-addrs 4 secure-src-and-dest-addrs	.1.3.6.1.4.1.9.5.32.4.1.1.26
ciscoTsPortCfgSoftErrThresholdmandatory The number of soft errors reported from a station connected to this port which, if exceeded, should cause a soft error exceeded trap to be issued. The error counters being monitored and compared to this threshold value…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.9.5.32.4.1.1.27
ciscoTsPortCfgSoftErrReportIntervalmandatory The sampling period, in seconds, in which each station connected to this port will be monitored for excessive soft error reports. If a station reports more than ciscoTsPortCfgSoftErrThreshold errors within the sampling …	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.9.5.32.4.1.1.28
ciscoTsPortCfgSoftErrorMonitoringmandatory Used to enable or disable, for this port, the collection of soft error statistics and the sending of traps when the configured error threshold is exceeded. If RMON statistics collection is not enabled, then the soft er…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.9.5.32.4.1.1.29

A table of statistical information about each port.
There is one entry for each port in a stack.  Entries
cannot be administratively created/deleted

ciscoTsPortStatsEntry row .1.3.6.1.4.1.9.5.32.4.2.1

Definition of rows in the port statistics table.

Indexes

ciscoTsStackSwitchNumber ciscoTsPortStatsNumber

Column	Syntax	OID
ciscoTsPortStatsNumbermandatory A unique value for each port entry. The value corresponds the port number.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.9.5.32.4.2.1.1
ciscoTsPortStatsModNumbermandatory Module number of the module that contains this port.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.9.5.32.4.2.1.2
ciscoTsPortStatsIfIndexmandatory A pointer to the entry in the ifTable corresponding to this port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.5.32.4.2.1.3
ciscoTsPortStatsRcvLocalFramesmandatory Number of frames received where the destination station address is on this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.4
ciscoTsPortStatsForwardedFramesmandatory Number of frames received on this port and forwarded to another port or to the system module for processing.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.5
ciscoTsPortStatsStationsmandatory Number of active stations in the address table for this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.6
ciscoTsPortStatsSWHandledFramesmandatory Number of frames received on this port and delivered to the system module for processing.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.7
ciscoTsPortStatsLocalStationsmandatory Number of stations on this port which belong to the local segment.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.8
ciscoTsPortStatsRemoteStationsmandatory Number of stations on this port which belong to another segment.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.9
ciscoTsPortStatsUnknownStaFramesmandatory Number of unicast frames received on this port and forwarded to the system module for processing because the source or destination station address is not in the port's forwarding table.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.10
ciscoTsPortStatsResetTimermandatory Time (in 100th second ticks) since the port counters were reset.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.11
ciscoTsPortStatsInFramesmandatory Total number of frames received on this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.12
ciscoTsPortStatsOutFramesmandatory Total number of frames transmitted by this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.13
ciscoTsPortStatsLongFramesmandatory Total number of frames received on this port which were too long.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.14
ciscoTsPortStatsShortFramesmandatory Total number of frames received on this port which were too short.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.15
ciscoTsPortStatsInBufOverflowsmandatory Total number of frames received on this port which caused a receive buffer overflow.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.16
ciscoTsPortStatsOutBufOverflowsmandatory Total number of frames which could not be transmitted from this port because of transmit buffer overflow.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.17
ciscoTsPortStatsRcvBcastsmandatory Number of broadcast frames received on this port without errors.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.18
ciscoTsPortStatsRcvMcastsmandatory Number of multicast frames received on this port without errors.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.19
ciscoTsPortStatsSwitchedFramesmandatory Number of frames switched on this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.20
ciscoTsPortStatsPktsInErrorsmandatory Total number of packets received or transmitted from this port in which there was an error.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.21
ciscoTsPortStatsAddrChainOverflowsmandatory Number of times an address chain was full when trying to add an entry to the port address table.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.22
ciscoTsPortStatsTableOverflowsmandatory Number of times the address table was full when trying to add an entry to the port address table.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.5.32.4.2.1.23
ciscoTsPortStatsCfgLossmandatory Number of events, as described in ciscoTsPortCfgLossRC, after the port has completed the join process and then lost communication.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.5.32.4.2.1.24
ciscoTsPortStatsCfgLossRCmandatory Reason code describing the cause of the latest configuration loss. A value of no-cfg-loss(7) will be returned when there has not been a configuration loss.	Enumeration Enumerated Values: 1 wire-fault 2 lobe-test-fail 3 tkp-mac-frame-rcv-in-txi-mode 4 heart-beat-fail 5 txi-new-station 6 txi-protocol-error 7 no-cfg-loss	.1.3.6.1.4.1.9.5.32.4.2.1.25
ciscoTsPortStatsTrCRFmandatory The TrCRF or TrCRFs that a port is assigned to. Only trunk ports such as ISL and ATM can be members of multiple TrCRFs. Each octet within the value of this object specifies a set of eight TrCRFs, with the first octet sp…	OctetString Constraints: range: 128-128	.1.3.6.1.4.1.9.5.32.4.2.1.26
ciscoTsPortStatsAutoDisableRCmandatory Reason code describing the cause for a port having been disabled by the switch software. A value of not-disabled(1) will be returned when the port has not been disabled by the switch software.	Enumeration Enumerated Values: 1 not-disabled 2 unknown 3 speed-error 4 remove-received 5 disabled-by-DRiP	.1.3.6.1.4.1.9.5.32.4.2.1.27

Passive probe port configuration table.  There
are always two entries in the table.  These
entries cannot be administratively deleted and
no rows can be created.

ciscoTsPassiveProbeEntry row .1.3.6.1.4.1.9.5.32.5.1.1

Definition of each row in the table.

Indexes

ciscoTsStackSwitchNumber ciscoTsPassiveProbeIndex

Column	Syntax	OID
ciscoTsPassiveProbeIndexmandatory Index into the Passive Probe port table. The following table describes the configuration options for the ciscoTsPassiveProbeTable. The PortMode column represents the operational mode of the ciscoTsPassiveProbeMonitoredP…	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.9.5.32.5.1.1.1
ciscoTsPassiveProbePortmandatory The port that is configured to mirror traffic from another port in the switch. This is the port to which you can connect an RMON probe. Setting this object to zero turns off the passive probe.	Integer32r/w Constraints: range: 0-28	.1.3.6.1.4.1.9.5.32.5.1.1.2
ciscoTsPassiveProbeMonitoredPortmandatory The port that will have its traffic mirrored onto the probe port. Set this object to a non-zero value to have that port's traffic copied to the monitoring port. The default value is 0.	Integer32r/w Constraints: range: 0-28	.1.3.6.1.4.1.9.5.32.5.1.1.3
ciscoTsPassiveProbeDirectionmandatory Direction of traffic flow that is being monitored.	Enumeration Enumerated Values: 1 transmit 2 receive 3 both 4 unknown	.1.3.6.1.4.1.9.5.32.5.1.1.4

TrCRF information table.  There is one entry
for each TrCRF in a stack.  Entries are administratively
created and deleted via the vtpEditControlTable.

ciscoTsTrCRFInfoEntry row .1.3.6.1.4.1.9.5.32.6.1.1

Definition of each row in the TrCRF Table

Indexes

ciscoTsTrCRFInfoTrCRFNumber

Column	Syntax	OID
ciscoTsTrCRFInfoTrCRFNumbermandatory Unique identifier for this entry in the TrCRF table. Corresponds to the TrCRF number. It is also the index into the vtpVLANEntry table which is in the VTP MIB.	Integer32 Constraints: range: 1-1024	.1.3.6.1.4.1.9.5.32.6.1.1.1
ciscoTsTrCRFInfoNamemandatory User defined name of the TrCRF. The name can only be set in the VTP MIB.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.5.32.6.1.1.2
ciscoTsTrCRFInfoSpanningTreeProtoSpecificationmandatory The Spanning Tree Protocol to run on this TrCRF.	Enumerationr/w Enumerated Values: 1 none 2 cisco 3 ieee 4 auto	.1.3.6.1.4.1.9.5.32.6.1.1.3
ciscoTsTrCRFInfoSpanningTreeBridgeForwardDelaymandatory The value used as the Forwarding Delay in this TrCRF. The range for this parameter is 400 to 3000 and is related to the value of dtrSpanningTreeBridgeMaxAge. See 802.1D-1990 for the relationship between dot1dStpBridg…	BRIDGE-MIBTimeoutr/w	.1.3.6.1.4.1.9.5.32.6.1.1.4
ciscoTsTrCRFInfoSpanningTreeBridgeHelloTimemandatory The value to be used as the Hello Time in this TrCRF. The range for this parameter is 100 to 1000. The granularity of this timer is specified to be 1/100 of a second. This agent will return a 'badValue' error if a set…	BRIDGE-MIBTimeoutr/w	.1.3.6.1.4.1.9.5.32.6.1.1.5
ciscoTsTrCRFInfoSpanningTreeBridgeMaxAgemandatory The value to be used as the Max Age in this TrCRF. The range for this parameter is 600 to 4000 and is related to the value of dtrSpanningTreeBridgeHelloTime. See 802.1D-1990 for the relationship between dot1dStpBridge…	BRIDGE-MIBTimeoutr/w	.1.3.6.1.4.1.9.5.32.6.1.1.6
ciscoTsTrCRFInfoSpanningTreeInternalPortModemandatory Used when configuring manual spanning tree. Setting this object to forwarding(2) or blocking(3) overrides the spanning tree's algorithm for TrCRF's logical internal port that connects it to the TrBRF.	Enumerationr/w Enumerated Values: 1 auto 2 forwarding 3 blocking	.1.3.6.1.4.1.9.5.32.6.1.1.7

TrBRF information table.  There is one entry
for each TrBRF in a stack.  Entries are administratively
created and deleted via the vtpEditControlTable.

ciscoTsTrBRFInfoEntry row .1.3.6.1.4.1.9.5.32.6.2.1

Definition of each row in the TrBRF Table

Indexes

ciscoTsTrBRFInfoTrBRFNumber

Column	Syntax	OID
ciscoTsTrBRFInfoTrBRFNumbermandatory Unique identifier for this entry in the TrBRF table. Corresponds to the TrBRF number. It is also the index into the vtpVLANEntry table which is in the VTP MIB.	Integer32 Constraints: range: 1-1024	.1.3.6.1.4.1.9.5.32.6.2.1.1
ciscoTsTrBRFInfoNamemandatory User defined name of the TrBRF. The name can only be set in the VTP MIB.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.5.32.6.2.1.2
ciscoTsTrBRFInfoIpStatemandatory IP configuration for this TrBRF.	Enumerationr/w Enumerated Values: 1 ip-disabled 2 bootp-when-needed 3 bootp-always	.1.3.6.1.4.1.9.5.32.6.2.1.3
ciscoTsTrBRFInfoIpAddressmandatory IP Address assigned to this TrBRF. Changes to the IP Address of the TrBRF to which the management station belongs cause loss of connectivity until the management station updates its information about the IP Address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.9.5.32.6.2.1.4
ciscoTsTrBRFInfoIpSubnetMaskmandatory The subnet mask for this TrBRF.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.9.5.32.6.2.1.5
ciscoTsTrBRFInfoIpDefaultGatewaymandatory The IP Address of the default gateway for this TrBRF.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.9.5.32.6.2.1.6
ciscoTsTrBRFInfoStpModemandatory This object is used to enable or disable the Spanning Tree Protocol for this TrBRF.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.9.5.32.6.2.1.7
ciscoTsTrBRFInfoIEEEStpUsesBridgeFuncAddrmandatory Enables the IEEE Spanning Tree Protocol at the TrBRF level to use the IBM bridge functional address instead of the default IEEE functional address.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.9.5.32.6.2.1.8

The TokenChannel table.  There are always eight entries
in the table, one for each possible channel.  These
entries cannot be administratively deleted and no
entries may be created.

ciscoTsTCEntry row .1.3.6.1.4.1.9.5.32.7.1.1

Definition of each row in the TokenChannel
table.

Indexes

ciscoTsTCSwitchNumber ciscoTsTCNumber

Column	Syntax	OID
ciscoTsTCSwitchNumbermandatory Switch number determined by the port number that the switch is connected to in a Matrix or as determined by the Stack Management software when two switches are connected back to back.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.9.5.32.7.1.1.1
ciscoTsTCNumbermandatory The unique identifier for this row. Corresponds to the TokenChannel number.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.9.5.32.7.1.1.2
ciscoTsTCPortsmandatory The set of ports in this switch which are active in this channel. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specify…	OctetStringr/w Constraints: range: 4-4	.1.3.6.1.4.1.9.5.32.7.1.1.3
ciscoTsTCStatusmandatory The current running status of the channel.	Enumeration Enumerated Values: 1 up 2 down 3 reduced	.1.3.6.1.4.1.9.5.32.7.1.1.4
ciscoTsTCActivePortsmandatory The set of ports in this switch which are active in this channel. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specify…	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.9.5.32.7.1.1.5

DSAP and SNAP Filter Class table. This table is global
for the entire stack.

ciscoTsProtocolClassFilterEntry row .1.3.6.1.4.1.9.5.32.8.1.1

Definition of each row in the filter class table.
There are 15 entries in the table, one for each
protocol class. These entries cannot be
administratively deleted and no entries may be
created.

Indexes

ciscoTsProtocolClassFilterIndex

Column	Syntax	OID
ciscoTsProtocolClassFilterIndexmandatory Protocol class table index.	Integer32 Constraints: range: 1-15	.1.3.6.1.4.1.9.5.32.8.1.1.1
ciscoTsProtocolClassFilterEtypemandatory This is the two byte ether-type for this protocol class. Only one ether type may be set per protocol class. Setting an illegal ether type will result in a 'badValue' error. Only 8 ether types can be configured. This obj…	OctetStringr/w	.1.3.6.1.4.1.9.5.32.8.1.1.2
ciscoTsProtocolClassFilterDSAPsmandatory This is the list of DSAPs associated with a protocol class. Up to sixteen DSAPs may be specified per protocol class. If any DSAP is an illegal value the entire object will be rejected.	OctetStringr/w	.1.3.6.1.4.1.9.5.32.8.1.1.3

DSAP and SNAP Filter table. This table allows you
to assign protocol classes and settings for each port.
There is one entry in the table for each protocol
class which has been enabled for filtering.

ciscoTsProtocolFilterEntry row .1.3.6.1.4.1.9.5.32.8.2.1

Definition of each row in the filter table.

Indexes

ciscoTsStackSwitchNumber ciscoTsProtocolFilterPort ciscoTsProtocolClassFilterIndex

Column	Syntax	OID
ciscoTsProtocolFilterPortmandatory This is the port in the switch to which this table entry corresponds.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.9.5.32.8.2.1.1
ciscoTsProtocolFilterBlockingModemandatory This determines the frame types that will be blocked for this protocol class on this port. Setting the values causes the following: all(1) - causes all frames in this class to be blocked sr(2) - causes…	Enumerationr/w Enumerated Values: 1 all 2 sr 3 nsr 4 none	.1.3.6.1.4.1.9.5.32.8.2.1.2
ciscoTsProtocolFilterTranspModemandatory If this port is in a SRT configured TrCRF, then setting this object will allow transparent bridging of frames in this protocol class. Setting this object to disable disallows transparent bridging of frames in this prot…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.9.5.32.8.2.1.3

A table of destination filters set up in the switch.
New filters are created by adding entries to this
table.  Note that values for all of the relevant objects
for a particular type of filter must be specified in a
single SNMP set operation on creation of a filter.  Set
operations which do not contain all of the required objects
for a given filter type will fail with an error-status
of 'genErr'.  The objects required for each filter type are
as follows:
          
ciscoTsMACDestFilterType   |   Required Objects for Creation
========================   |   =============================
block-dest(1)              |   ciscoTsMACDestFilterPorts
---------------------------|--------------------------------
allow-dest(2)              |   ciscoTsMACDestFilterPorts
---------------------------|--------------------------------
limited-multicast(3)       |   ciscoTsMACDestFilterPorts
                          |   ciscoTsMACDestFilterExitMask
---------------------------|--------------------------------
force-dest(4)              |   ciscoTsMACDestFilterPorts
                          |   ciscoTsMACDestFilterRemoteBox
                          |   ciscoTsMACDestFilterRemotePort 
          
Since the indices for the table are switch number, MAC
address, and filter type, the instance information for a given
object specifies which filter is being created.  For example,
a set request for
          
      ciscoTsMACDestFilterPorts.s.a1.a2.a3.a4.a5.a6.t
          
will create a filter of type 't' (as enumerated for
ciscoTsMACDestFilterType) for MAC address a1:a2:a3:a4:a5:a6
on switch number 's'.

ciscoTsMACDestFilterEntry row .1.3.6.1.4.1.9.5.32.8.3.1

Definition of each row in the filter table.

Indexes

ciscoTsMACDestFilterSwitchNumber ciscoTsMACDestFilterStationAddress ciscoTsMACDestFilterType

Column	Syntax	OID
ciscoTsMACDestFilterSwitchNumbermandatory Switch number determined by the port number that the switch is connected to in a Matrix or as determined by the Stack Management software when two switches are connected back to back.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.9.5.32.8.3.1.1
ciscoTsMACDestFilterStationAddressmandatory The destination MAC address in a frame to which this entry's filtering information applies.	MacAddr Type Constraints: range: 6	.1.3.6.1.4.1.9.5.32.8.3.1.2
ciscoTsMACDestFilterTypemandatory There are three types of destination MAC address filters: (1) Block destination address at specific ports. Indicates that the specified ports must not send frames to the specified destination station address. (2) Allow …	Enumerationr/w Enumerated Values: 1 block-dest 2 allow-dest 3 limited-multicast 4 force-dest	.1.3.6.1.4.1.9.5.32.8.3.1.3
ciscoTsMACDestFilterPortsmandatory The set of ports to which this filter is applied. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 throu…	OctetStringr/w Constraints: range: 4-4	.1.3.6.1.4.1.9.5.32.8.3.1.4
ciscoTsMACDestFilterExitMaskmandatory The set of output ports to which a limited multicast filter is applied. This object only has a value for Limited Multicast filters. Each octet within the value of this object specifies a set of eight ports, with the fi…	OctetStringr/w Constraints: range: 4-4	.1.3.6.1.4.1.9.5.32.8.3.1.5
ciscoTsMACDestFilterRemoteBoxmandatory The remote switch to be used for a force destination filter.	Integer32r/w Constraints: range: 1-8	.1.3.6.1.4.1.9.5.32.8.3.1.6
ciscoTsMACDestFilterRemotePortmandatory The remote port to be used for a force destination filter.	Integer32r/w Constraints: range: 1-32	.1.3.6.1.4.1.9.5.32.8.3.1.7
ciscoTsMACDestFilterStatusmandatory A get request always returns valid(1). Set this object to invalid(2) to delete an entry.	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.9.5.32.8.3.1.8

A table of source filters set up in the switch.
New filters are created by adding entries to this
table.  Note that values for all of the relevant objects
for a particular type of filter must be specified in a
single SNMP set operation on creation of a filter.  Set
operations which do not contain all of the required objects
for a given filter type will fail with an error-status
of 'genErr'.  The objects required for each filter type are
as follows:
          
ciscoTsMACSourceFilterType  |  Required Objects for Creation
==========================  |  =============================
block-src(1)                |  ciscoTsMACSourceFilterPorts
----------------------------|-------------------------------
allow-src(2)                |  ciscoTsMACSourceFilterPorts
          
Since the indices for the table are switch number, MAC
address, and filter type, the instance information for a given
object specifies which filter is being created.  For example,
a set request for
          
      ciscoTsMACSourceFilterPorts.s.a1.a2.a3.a4.a5.a6.t
          
will create a filter of type 't' (as enumerated for
ciscoTsMACSourceFilterType) for MAC address a1:a2:a3:a4:a5:a6
on switch number 's'.

ciscoTsMACSourceFilterEntry row .1.3.6.1.4.1.9.5.32.8.4.1

Definition of each row in the filter table.

Indexes

ciscoTsMACSourceFilterSwitchNumber ciscoTsMACSourceFilterStationAddress ciscoTsMACSourceFilterType

Column	Syntax	OID
ciscoTsMACSourceFilterSwitchNumbermandatory Switch number determined by the port number that the switch is connected to in a Matrix or as determined by the Stack Management software when two switches are connected back to back.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.9.5.32.8.4.1.1
ciscoTsMACSourceFilterStationAddressmandatory The destination MAC address in a frame to which this entry's filtering information applies.	MacAddr Type Constraints: range: 6	.1.3.6.1.4.1.9.5.32.8.4.1.2
ciscoTsMACSourceFilterTypemandatory There are two types of source address filters: (1) Block source address at specific ports. Indicates that the specific source addresses must not send frames from specified ports. (2) Allow source address at specific por…	Enumerationr/w Enumerated Values: 1 block-source 2 allow-source	.1.3.6.1.4.1.9.5.32.8.4.1.3
ciscoTsMACSourceFilterPortsmandatory The set of ports to which this filter is applied. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 throu…	OctetStringr/w Constraints: range: 4-4	.1.3.6.1.4.1.9.5.32.8.4.1.4
ciscoTsMACSourceFilterStatusmandatory A get request always returns valid(1). Set this object to invalid(2) to delete an entry.	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.9.5.32.8.4.1.5

A table of MAC addresses that have been identified as
duplicates within an address scope.  There is one
entry in the tale for each such address.  Entries
cannot be administratively created/deleted.

ciscoTsDupAddrFilterEntry row .1.3.6.1.4.1.9.5.32.8.5.1

Definition of rows in the duplicate address table.

Indexes

ciscoTsDupAddrFilterSwitchNumber ciscoTsDupAddrFilterStationAddress

Column	Syntax	OID
ciscoTsDupAddrFilterSwitchNumbermandatory Switch number determined by the port number that the switch is connected to in a Matrix or as determined by the Stack Management software when two switches are connected back to back.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.9.5.32.8.5.1.1
ciscoTsDupAddrFilterStationAddressmandatory The MAC address that has been identified as being a duplicate. All frames having this MAC address as their source address are being discarded at the ports specified in ciscoTsDupAddrFilterPorts.	MacAddr Type Constraints: range: 6	.1.3.6.1.4.1.9.5.32.8.5.1.2
ciscoTsDupAddrFilterPortsmandatory A bit mask representing all the ports on which this duplicate MAC address is currently being filtered. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 t…	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.9.5.32.8.5.1.3

DSAP and SNAP Filter table for trunk ports which support
protocol filters on a per-TrCRF basis. This table allows you
to assign protocol classes and settings for each TrCRF on
each trunk port.  There is one entry in the table for
each (switch, port, TrCRF, protocol class) tuple for which
filtering has been enabled.

ciscoTsTrunkProtocolFilterEntry row .1.3.6.1.4.1.9.5.32.8.6.1

Definition of each row in the filter table.

Indexes

ciscoTsStackSwitchNumber ciscoTsTrunkProtocolFilterPort ciscoTsTrCRFInfoTrCRFNumber ciscoTsProtocolClassFilterIndex

Column	Syntax	OID
ciscoTsTrunkProtocolFilterPortmandatory This is the port in the switch to which this table entry corresponds.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.9.5.32.8.6.1.1
ciscoTsTrunkProtocolFilterBlockingModemandatory This determines the frame types that will be blocked for this protocol class on this TrCRF on this port. Setting the values causes the following: all(1) - causes all frames in this class to be blocked sr…	Enumerationr/w Enumerated Values: 1 all 2 sr 3 nsr 4 none	.1.3.6.1.4.1.9.5.32.8.6.1.2
ciscoTsTrunkProtocolFilterTranspModemandatory If this port is in a SRT configured TrCRF, then setting this object will allow transparent bridging of frames in this protocol class. Setting this object to disable disallows transparent bridging of frames in this prot…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.9.5.32.8.6.1.3