CISCO-OPTICAL-OTS-MIB

        This MIB module defines the managed objects and statistics
objects for physical layer characteristics of optical line
systems and optical transport devices.
Performance monitoring (PM) parameters are used to gather,
store, set thresholds for and report
performance data for early detection of problems.
Thresholds are used to set error levels for each PM parameter.
During the accumulation cycle, if the current value of a
performance monitoring parameter reaches or exceeds its
corresponding threshold value, a threshold crossing alarm (TCA)
is generated. The TCAs provide early detection of performance
degradation.
Glossary:
OTS       : Optical Transmission Section
OTS-OCH   : Optical Channel Information on OTS
ATTN      : Optical Attenuation
GAIN      : Optical Amplifier Gain
TILT      : Optical Amplifier TILT
LBC       : Laser Bias Current
OSRI      : Optical Safety Remote Interlock
TX        : Transmit
RX        : Receive
VOA       : Variable Optical Attenuator
dB        : Decibel
dBm       : Decibel-milliwatt
mW        : Milliwatt
nm        : Nanometer.
    
Source file
CISCO-OPTICAL-OTS-MIB
Last revised
Identity
ciscoOpticalOtsMIB
Base OID
1.3.6.1.4.1.9.9.834
Imported Objects
CISCO-OPTICAL-MIB CoiIntervalType CoiOptAlarmServiceAffecting CoiOptAlarmSeverity CoiOptAlarmStatus CoiOptAlarmType CoiOpticalPower CoiOpticalWavelength
CISCO-SMI ciscoMgmt
IF-MIB ifIndex ifName
SNMP-FRAMEWORK-MIB SnmpAdminString
SNMPv2-CONF MODULE-COMPLIANCE (no object page) NOTIFICATION-GROUP (no object page) OBJECT-GROUP (no object page)
SNMPv2-SMI Integer32 MODULE-IDENTITY (no object page) NOTIFICATION-TYPE (no object page) OBJECT-TYPE (no object page) Unsigned32
SNMPv2-TC DisplayString TEXTUAL-CONVENTION (no object page) TimeStamp TruthValue
Net-SNMP examples using the cisco MIB directory Show commands

These commands use the standard Observium installation path and load the selected MIB variant before the RFC and Net-SNMP directories.

Translate the module identity
/usr/bin/snmptranslate -Pud -Ir -On -m 'CISCO-OPTICAL-OTS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'CISCO-OPTICAL-OTS-MIB::ciscoOpticalOtsMIB'
Walk the MIB subtree
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-OPTICAL-OTS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-OPTICAL-OTS-MIB::ciscoOpticalOtsMIB'
How SNMP, Net-SNMP, MIB paths, and variants work
Objects (253)
.1.3.6.1.4.1.9.9.834
.1.3.6.1.4.1.9.9.834.0
.1.3.6.1.4.1.9.9.834.1
.1.3.6.1.4.1.9.9.834.1.1
.1.3.6.1.4.1.9.9.834.1.1.1
.1.3.6.1.4.1.9.9.834.1.1.2
.1.3.6.1.4.1.9.9.834.1.1.2.1
.1.3.6.1.4.1.9.9.834.1.1.2.1.1
.1.3.6.1.4.1.9.9.834.1.1.2.1.10
.1.3.6.1.4.1.9.9.834.1.1.2.1.11
.1.3.6.1.4.1.9.9.834.1.1.2.1.12
.1.3.6.1.4.1.9.9.834.1.1.2.1.13
.1.3.6.1.4.1.9.9.834.1.1.2.1.14
.1.3.6.1.4.1.9.9.834.1.1.2.1.15
.1.3.6.1.4.1.9.9.834.1.1.2.1.16
.1.3.6.1.4.1.9.9.834.1.1.2.1.17
.1.3.6.1.4.1.9.9.834.1.1.2.1.18
.1.3.6.1.4.1.9.9.834.1.1.2.1.19
.1.3.6.1.4.1.9.9.834.1.1.2.1.2
.1.3.6.1.4.1.9.9.834.1.1.2.1.20
.1.3.6.1.4.1.9.9.834.1.1.2.1.21
Bits
.1.3.6.1.4.1.9.9.834.1.1.2.1.22
.1.3.6.1.4.1.9.9.834.1.1.2.1.23
.1.3.6.1.4.1.9.9.834.1.1.2.1.24
.1.3.6.1.4.1.9.9.834.1.1.2.1.25
.1.3.6.1.4.1.9.9.834.1.1.2.1.26
.1.3.6.1.4.1.9.9.834.1.1.2.1.27
.1.3.6.1.4.1.9.9.834.1.1.2.1.28
.1.3.6.1.4.1.9.9.834.1.1.2.1.29
.1.3.6.1.4.1.9.9.834.1.1.2.1.3
.1.3.6.1.4.1.9.9.834.1.1.2.1.30
.1.3.6.1.4.1.9.9.834.1.1.2.1.31
.1.3.6.1.4.1.9.9.834.1.1.2.1.32
.1.3.6.1.4.1.9.9.834.1.1.2.1.33
.1.3.6.1.4.1.9.9.834.1.1.2.1.34
.1.3.6.1.4.1.9.9.834.1.1.2.1.35
.1.3.6.1.4.1.9.9.834.1.1.2.1.36
.1.3.6.1.4.1.9.9.834.1.1.2.1.37
.1.3.6.1.4.1.9.9.834.1.1.2.1.38
Enumeration
.1.3.6.1.4.1.9.9.834.1.1.2.1.39
.1.3.6.1.4.1.9.9.834.1.1.2.1.4
Enumeration
.1.3.6.1.4.1.9.9.834.1.1.2.1.40
.1.3.6.1.4.1.9.9.834.1.1.2.1.41
Enumeration
.1.3.6.1.4.1.9.9.834.1.1.2.1.42
.1.3.6.1.4.1.9.9.834.1.1.2.1.43
.1.3.6.1.4.1.9.9.834.1.1.2.1.44
.1.3.6.1.4.1.9.9.834.1.1.2.1.45
.1.3.6.1.4.1.9.9.834.1.1.2.1.46
.1.3.6.1.4.1.9.9.834.1.1.2.1.47
.1.3.6.1.4.1.9.9.834.1.1.2.1.48
.1.3.6.1.4.1.9.9.834.1.1.2.1.5
.1.3.6.1.4.1.9.9.834.1.1.2.1.6
.1.3.6.1.4.1.9.9.834.1.1.2.1.7
.1.3.6.1.4.1.9.9.834.1.1.2.1.8
.1.3.6.1.4.1.9.9.834.1.1.2.1.9
.1.3.6.1.4.1.9.9.834.1.1.3
.1.3.6.1.4.1.9.9.834.1.1.3.1
.1.3.6.1.4.1.9.9.834.1.1.3.1.1
.1.3.6.1.4.1.9.9.834.1.1.3.1.10
.1.3.6.1.4.1.9.9.834.1.1.3.1.11
Bits
.1.3.6.1.4.1.9.9.834.1.1.3.1.12
1/10 GHzUnsigned32
.1.3.6.1.4.1.9.9.834.1.1.3.1.13
.1.3.6.1.4.1.9.9.834.1.1.3.1.2
.1.3.6.1.4.1.9.9.834.1.1.3.1.3
.1.3.6.1.4.1.9.9.834.1.1.3.1.4
.1.3.6.1.4.1.9.9.834.1.1.3.1.5
.1.3.6.1.4.1.9.9.834.1.1.3.1.6
.1.3.6.1.4.1.9.9.834.1.1.3.1.7
100 MHzUnsigned32
.1.3.6.1.4.1.9.9.834.1.1.3.1.8
Unsigned32
.1.3.6.1.4.1.9.9.834.1.1.3.1.9
.1.3.6.1.4.1.9.9.834.1.1.4
.1.3.6.1.4.1.9.9.834.1.1.5
.1.3.6.1.4.1.9.9.834.1.1.5.1
.1.3.6.1.4.1.9.9.834.1.1.5.1.1
.1.3.6.1.4.1.9.9.834.1.1.5.1.10
.1.3.6.1.4.1.9.9.834.1.1.5.1.11
.1.3.6.1.4.1.9.9.834.1.1.5.1.12
.1.3.6.1.4.1.9.9.834.1.1.5.1.13
Enumeration
.1.3.6.1.4.1.9.9.834.1.1.5.1.14
.1.3.6.1.4.1.9.9.834.1.1.5.1.15
.1.3.6.1.4.1.9.9.834.1.1.5.1.16
.1.3.6.1.4.1.9.9.834.1.1.5.1.2
.1.3.6.1.4.1.9.9.834.1.1.5.1.3
.1.3.6.1.4.1.9.9.834.1.1.5.1.4
.1.3.6.1.4.1.9.9.834.1.1.5.1.5
.1.3.6.1.4.1.9.9.834.1.1.5.1.6
.1.3.6.1.4.1.9.9.834.1.1.5.1.7
.1.3.6.1.4.1.9.9.834.1.1.5.1.8
.1.3.6.1.4.1.9.9.834.1.1.5.1.9
.1.3.6.1.4.1.9.9.834.1.1.6
.1.3.6.1.4.1.9.9.834.1.1.6.1
.1.3.6.1.4.1.9.9.834.1.1.6.1.1
.1.3.6.1.4.1.9.9.834.1.1.7
.1.3.6.1.4.1.9.9.834.1.1.7.1
.1.3.6.1.4.1.9.9.834.1.1.7.1.1
.1.3.6.1.4.1.9.9.834.1.1.7.1.10
.1.3.6.1.4.1.9.9.834.1.1.7.1.11
.1.3.6.1.4.1.9.9.834.1.1.7.1.12
.1.3.6.1.4.1.9.9.834.1.1.7.1.13
.1.3.6.1.4.1.9.9.834.1.1.7.1.14
.1.3.6.1.4.1.9.9.834.1.1.7.1.15
.1.3.6.1.4.1.9.9.834.1.1.7.1.16
.1.3.6.1.4.1.9.9.834.1.1.7.1.17
.1.3.6.1.4.1.9.9.834.1.1.7.1.18
.1.3.6.1.4.1.9.9.834.1.1.7.1.19
.1.3.6.1.4.1.9.9.834.1.1.7.1.2
.1.3.6.1.4.1.9.9.834.1.1.7.1.20
.1.3.6.1.4.1.9.9.834.1.1.7.1.21
Bits
.1.3.6.1.4.1.9.9.834.1.1.7.1.22
.1.3.6.1.4.1.9.9.834.1.1.7.1.23
.1.3.6.1.4.1.9.9.834.1.1.7.1.24
.1.3.6.1.4.1.9.9.834.1.1.7.1.25
.1.3.6.1.4.1.9.9.834.1.1.7.1.26
.1.3.6.1.4.1.9.9.834.1.1.7.1.27
.1.3.6.1.4.1.9.9.834.1.1.7.1.28
.1.3.6.1.4.1.9.9.834.1.1.7.1.29
.1.3.6.1.4.1.9.9.834.1.1.7.1.3
.1.3.6.1.4.1.9.9.834.1.1.7.1.30
.1.3.6.1.4.1.9.9.834.1.1.7.1.31
.1.3.6.1.4.1.9.9.834.1.1.7.1.32
.1.3.6.1.4.1.9.9.834.1.1.7.1.33
.1.3.6.1.4.1.9.9.834.1.1.7.1.34
.1.3.6.1.4.1.9.9.834.1.1.7.1.35
.1.3.6.1.4.1.9.9.834.1.1.7.1.36
.1.3.6.1.4.1.9.9.834.1.1.7.1.37
.1.3.6.1.4.1.9.9.834.1.1.7.1.38
Enumeration
.1.3.6.1.4.1.9.9.834.1.1.7.1.39
.1.3.6.1.4.1.9.9.834.1.1.7.1.4
Enumeration
.1.3.6.1.4.1.9.9.834.1.1.7.1.40
.1.3.6.1.4.1.9.9.834.1.1.7.1.41
Enumeration
.1.3.6.1.4.1.9.9.834.1.1.7.1.42
.1.3.6.1.4.1.9.9.834.1.1.7.1.43
.1.3.6.1.4.1.9.9.834.1.1.7.1.44
.1.3.6.1.4.1.9.9.834.1.1.7.1.45
.1.3.6.1.4.1.9.9.834.1.1.7.1.46
.1.3.6.1.4.1.9.9.834.1.1.7.1.47
.1.3.6.1.4.1.9.9.834.1.1.7.1.48
.1.3.6.1.4.1.9.9.834.1.1.7.1.5
.1.3.6.1.4.1.9.9.834.1.1.7.1.6
.1.3.6.1.4.1.9.9.834.1.1.7.1.7
.1.3.6.1.4.1.9.9.834.1.1.7.1.8
.1.3.6.1.4.1.9.9.834.1.1.7.1.9
.1.3.6.1.4.1.9.9.834.1.2
.1.3.6.1.4.1.9.9.834.1.2.1
.1.3.6.1.4.1.9.9.834.1.2.1.1
.1.3.6.1.4.1.9.9.834.1.2.1.1.1
.1.3.6.1.4.1.9.9.834.1.2.1.1.10
.1.3.6.1.4.1.9.9.834.1.2.1.1.11
.1.3.6.1.4.1.9.9.834.1.2.1.1.12
.1.3.6.1.4.1.9.9.834.1.2.1.1.13
1/100 dBInteger32
.1.3.6.1.4.1.9.9.834.1.2.1.1.14
1/100 dBInteger32
.1.3.6.1.4.1.9.9.834.1.2.1.1.15
.1.3.6.1.4.1.9.9.834.1.2.1.1.16
.1.3.6.1.4.1.9.9.834.1.2.1.1.17
1/100 dBInteger32
.1.3.6.1.4.1.9.9.834.1.2.1.1.18
1/100 dbInteger32
.1.3.6.1.4.1.9.9.834.1.2.1.1.19
.1.3.6.1.4.1.9.9.834.1.2.1.1.2
.1.3.6.1.4.1.9.9.834.1.2.1.1.20
.1.3.6.1.4.1.9.9.834.1.2.1.1.21
.1.3.6.1.4.1.9.9.834.1.2.1.1.3
1/10 percentUnsigned32
.1.3.6.1.4.1.9.9.834.1.2.1.1.4
.1.3.6.1.4.1.9.9.834.1.2.1.1.5
.1.3.6.1.4.1.9.9.834.1.2.1.1.6
1/10 percentUnsigned32
.1.3.6.1.4.1.9.9.834.1.2.1.1.7
.1.3.6.1.4.1.9.9.834.1.2.1.1.8
.1.3.6.1.4.1.9.9.834.1.2.1.1.9
.1.3.6.1.4.1.9.9.834.1.2.2
.1.3.6.1.4.1.9.9.834.1.2.2.1
.1.3.6.1.4.1.9.9.834.1.2.2.1.1
1/10 percentUnsigned32
.1.3.6.1.4.1.9.9.834.1.2.2.1.10
OctetString
.1.3.6.1.4.1.9.9.834.1.2.2.1.11
.1.3.6.1.4.1.9.9.834.1.2.2.1.12
.1.3.6.1.4.1.9.9.834.1.2.2.1.13
.1.3.6.1.4.1.9.9.834.1.2.2.1.14
.1.3.6.1.4.1.9.9.834.1.2.2.1.15
.1.3.6.1.4.1.9.9.834.1.2.2.1.16
.1.3.6.1.4.1.9.9.834.1.2.2.1.17
.1.3.6.1.4.1.9.9.834.1.2.2.1.18
.1.3.6.1.4.1.9.9.834.1.2.2.1.19
.1.3.6.1.4.1.9.9.834.1.2.2.1.2
.1.3.6.1.4.1.9.9.834.1.2.2.1.20
.1.3.6.1.4.1.9.9.834.1.2.2.1.21
.1.3.6.1.4.1.9.9.834.1.2.2.1.22
.1.3.6.1.4.1.9.9.834.1.2.2.1.23
.1.3.6.1.4.1.9.9.834.1.2.2.1.24
.1.3.6.1.4.1.9.9.834.1.2.2.1.25
.1.3.6.1.4.1.9.9.834.1.2.2.1.26
.1.3.6.1.4.1.9.9.834.1.2.2.1.27
.1.3.6.1.4.1.9.9.834.1.2.2.1.28
.1.3.6.1.4.1.9.9.834.1.2.2.1.29
.1.3.6.1.4.1.9.9.834.1.2.2.1.3
.1.3.6.1.4.1.9.9.834.1.2.2.1.30
.1.3.6.1.4.1.9.9.834.1.2.2.1.31
.1.3.6.1.4.1.9.9.834.1.2.2.1.32
.1.3.6.1.4.1.9.9.834.1.2.2.1.33
.1.3.6.1.4.1.9.9.834.1.2.2.1.34
.1.3.6.1.4.1.9.9.834.1.2.2.1.35
1/10 percentUnsigned32
.1.3.6.1.4.1.9.9.834.1.2.2.1.4
.1.3.6.1.4.1.9.9.834.1.2.2.1.5
.1.3.6.1.4.1.9.9.834.1.2.2.1.6
1/10 percentUnsigned32
.1.3.6.1.4.1.9.9.834.1.2.2.1.7
.1.3.6.1.4.1.9.9.834.1.2.2.1.8
.1.3.6.1.4.1.9.9.834.1.2.2.1.9
.1.3.6.1.4.1.9.9.834.1.2.3
.1.3.6.1.4.1.9.9.834.1.2.3.1
.1.3.6.1.4.1.9.9.834.1.2.3.1.1
.1.3.6.1.4.1.9.9.834.1.2.3.1.10
1/10 percentUnsigned32
.1.3.6.1.4.1.9.9.834.1.2.3.1.11
OctetString
.1.3.6.1.4.1.9.9.834.1.2.3.1.12
.1.3.6.1.4.1.9.9.834.1.2.3.1.13
.1.3.6.1.4.1.9.9.834.1.2.3.1.14
.1.3.6.1.4.1.9.9.834.1.2.3.1.15
.1.3.6.1.4.1.9.9.834.1.2.3.1.16
.1.3.6.1.4.1.9.9.834.1.2.3.1.17
.1.3.6.1.4.1.9.9.834.1.2.3.1.18
.1.3.6.1.4.1.9.9.834.1.2.3.1.19
Unsigned32
.1.3.6.1.4.1.9.9.834.1.2.3.1.2
.1.3.6.1.4.1.9.9.834.1.2.3.1.20
.1.3.6.1.4.1.9.9.834.1.2.3.1.21
.1.3.6.1.4.1.9.9.834.1.2.3.1.22
.1.3.6.1.4.1.9.9.834.1.2.3.1.23
.1.3.6.1.4.1.9.9.834.1.2.3.1.24
.1.3.6.1.4.1.9.9.834.1.2.3.1.25
.1.3.6.1.4.1.9.9.834.1.2.3.1.26
.1.3.6.1.4.1.9.9.834.1.2.3.1.27
.1.3.6.1.4.1.9.9.834.1.2.3.1.28
.1.3.6.1.4.1.9.9.834.1.2.3.1.29
.1.3.6.1.4.1.9.9.834.1.2.3.1.3
.1.3.6.1.4.1.9.9.834.1.2.3.1.30
.1.3.6.1.4.1.9.9.834.1.2.3.1.31
.1.3.6.1.4.1.9.9.834.1.2.3.1.32
.1.3.6.1.4.1.9.9.834.1.2.3.1.33
.1.3.6.1.4.1.9.9.834.1.2.3.1.34
.1.3.6.1.4.1.9.9.834.1.2.3.1.35
.1.3.6.1.4.1.9.9.834.1.2.3.1.36
.1.3.6.1.4.1.9.9.834.1.2.3.1.4
1/10 percentUnsigned32
.1.3.6.1.4.1.9.9.834.1.2.3.1.5
.1.3.6.1.4.1.9.9.834.1.2.3.1.6
.1.3.6.1.4.1.9.9.834.1.2.3.1.7
1/10 percentUnsigned32
.1.3.6.1.4.1.9.9.834.1.2.3.1.8
.1.3.6.1.4.1.9.9.834.1.2.3.1.9
.1.3.6.1.4.1.9.9.834.1.5
.1.3.6.1.4.1.9.9.834.1.5.1
.1.3.6.1.4.1.9.9.834.1.5.2
.1.3.6.1.4.1.9.9.834.1.5.3
.1.3.6.1.4.1.9.9.834.1.5.4
.1.3.6.1.4.1.9.9.834.1.5.5
.1.3.6.1.4.1.9.9.834.1.5.6
.1.3.6.1.4.1.9.9.834.1.5.7
.1.3.6.1.4.1.9.9.834.1.5.8
.1.3.6.1.4.1.9.9.834.2
.1.3.6.1.4.1.9.9.834.2.1
.1.3.6.1.4.1.9.9.834.2.2
Dependencies (9) 7 direct · 2 transitive Show tree and compile order Hide dependency details

Each imported module is resolved in the importing module's source directory first, then through the normal default-variant rules.

Dependency tree
Type Definitions (19)
Integer32 range: 0range: 30..400
OTS ports associated with an amplifier device. This value
represents the amplifier both Ingress and Egress gain setting.
The gain is expressed in 1/10ths of a dB.

A value of 0 indicates that the amplifier is switched off.

Example:
A value of 120 represents a gain level of 12.0 dB.
Enumeration
up(1)
down(2)
This value indicates the controller status.
Valid values are -

up(1) : controller admin up
down(2) : controller admin down
Enumeration
manual(1)
auto(2)
power(3)
OTS ports associated to amplifier device, this value indicates
how the amplifier is controlled.
Valid values are -
manual(1) : manual control mode (An external entity has to
provide gain/tilt settings)
auto(2) : automatic control mode (An internal will provide
gain/tilt calculation based on power setpoint)
power(3) : power control mode (An internal will provide
gain/tilt calculation based on power mode settings
Enumeration
normal(1)
extended(2)
OTS ports associated to amplifier device, this value indicates
the working ranges available for amplifier gain.
Valid values are -

normal(1) : normal gain range
extended(2) : extended gain range
Enumeration
auto(1)
disabled(2)
OTS ports associated to amplifier device, this value indicates
how the safety compliaces regulation are statisfied.
Valid values are -

auto(1) : automatic safety control mode
disabled(2) : disabled safety control mode
Integer32 range: -5000..0
An integer value that represents BR Ratio
in dB.
Example: The value -4500 represents a BR Ratio
of -45.00 dB.
Integer32 range: -100..4000
OTS ports associated to amplifier device,this value represent
the amplifier gain setting.
An integer value that represents the gain level in
1/100ths of dB.
A negative value represents not meaninful value in case the
amplifier is switched off for any reason.
Example:
The value 800 represents an gain level of 8.0 dB.
Integer32 range: 80..400
OTS ports associated to amplifier device,this value represent
the amplifier gain setting for Ingress and Egress Amplifiers.
An integer value that represents the gain level in
1/10ths of dB.
A negative value indicates that the amplifier
is switched off for any reason.
Example:
The value 80 represents an gain level of 8.0 dB.
Integer32 range: -50..50
This value represents the tilt parameter for an OTS port
associated to the amplifier device.
An integer value that represents the tilt level in 1/10ths of
dB.
Example:
The value 30 represents a tilt level of 3.0 dB.
Enumeration
unknown(1)
on(2)
off(3)
apr(4)
This value indicates the module laser status.
Valid values are -

unknown(1) : unknown status
on(2) : laser on
off(3) : laser off
apr(4) : Denotes Automatic Power Reduction (APR)
Enumeration
on(1)
off(2)
OTS ports associated to amplifier device, this value indicates
the optical safety remote interlock (OSRI) status.
Valid values are -

on(1) : force laser shutdown for safety interlock
off(2) : normal operation
Enumeration
line(1)
com(2)
osc(3)
comCheck(4)
working(5)
protected(6)
addDrop(7)
This value indicates the port type for optical OTS
interface.
Valid values are -
line(1) : port facing the fiber and far-end section.
com(2) : port facing the near-end section.
osc(3) : port for optical service channel signal.
comCheck(4) : com monitoring port for near-end safety usage.
working(5) : physical working port if device protection.
protected(6) : physical protected port if device protection.
Enumeration
active(1)
standby(2)
This value indicates the actual OTS port role in case a
protection device is in place.
Valid values are -

active(1) : active port
standby(2) : standby port
Enumeration
up(1)
down(2)
adminDown(3)
This value indicates the controller status.
Valid values are -

up(1) : controller operstatus up
down(2) : controller operstatus down
adminDown(3) : controller administratively down
Integer32 range: -5000..10000
An integer value that represents Temperature
in Celsius for OTS controllers.
Example: The value 4500 represents a Temperature
45.00 C.
Integer32 range: -500..500
OTS ports associated to amplifier device, this values represent
the tilt parameter.
An integer value that represents the tilt level in 1/100ths of
dB.
Example:
The value 300 represents a tilt level of 3.0 dB.
Enumeration
inService(1)
outOfService(2)
maintenance(3)
ains(4)
This value indicates the transport administrative status.
Valid values are -

inService(1) : transport administrative status in-service
outOfService(2) : transport administrative status out-of-service
maintenance(3) : transport administrative status maintenance
ains(4) : transport administrative status automatic
in-service
Unsigned32
An unsigned integer value that represents the VOA attenuation
level in 1/100ths of dB.
Example: The value 200 represents an attenuation
level of 2.0 dB.
Integer32 range: -5000..10000
An integer value that represents Voltage
for OTS controller.
Example: The value 350 represents a Voltage
3.50 V.
Conformance Groups (14)
cooOtsControllerPortType cooOtsControllerLaserStatus cooOtsControllerRXPower cooOtsControllerTXPower cooOtsControllerAmpliGain cooOtsControllerAmpliTilt cooOtsControllerTotalRXPower cooOtsControllerTotalTXPower cooOtsControllerRXVoaAttenuation cooOtsControllerTXVoaAttenuation cooOtsControllerRXLowThreshold cooOtsControllerTXLowThreshold cooOtsControllerAmpliChannelPwr cooOtsControllerChannelPwrMaxDelta cooOtsControllerAmpliControlMode cooOtsControllerAmpliGainRange cooOtsControllerAmpliSafetyCtrlMode cooOtsControllerOsri cooOtsControllerProtectionPortRole cooOtsControllerState cooOtsControllerTranspAdminState cooOtsControllerAlarmState cooThreshTXPowerMin cooThreshRXPowerMin cooThreshLBCMin cooThreshTXPowerMax cooThreshRXPowerMax cooThreshLBCMax cooCurrentTXPowerMax cooCurrentRXPowerMax cooCurrentLBCMax cooCurrentTXPowerMin cooCurrentRXPowerMin cooCurrentLBCMin cooCurrentTXPowerAvg cooCurrentRXPowerAvg cooCurrentLBCAvg cooIntervalTXPowerMax cooIntervalRXPowerMax cooIntervalLBCMax cooIntervalTXPowerMin cooIntervalRXPowerMin cooIntervalLBCMin cooIntervalTXPowerAvg cooIntervalRXPowerAvg cooIntervalLBCAvg cooOtsControllerRXSpanLoss cooOtsControllerTXSpanLoss cooOtsControllerRXEnabled cooOtsControllerTXEnabled cooThreshAmpliGainMin cooThreshAmpliGainMax cooThreshAmpliGainEnableMax cooThreshAmpliGainEnableMin cooThreshAmpliGainTiltMin cooThreshAmpliGainTiltMax cooThreshAmpliGainTiltEnableMax cooThreshAmpliGainTiltEnableMin cooCurrentAmpliGainMin cooCurrentAmpliGainMax cooCurrentAmpliGainAvg cooCurrentAmpliGainTiltMin cooCurrentAmpliGainTiltMax cooCurrentAmpliGainTiltAvg cooIntervalAmpliGainMin cooIntervalAmpliGainMax cooIntervalAmpliGainAvg cooIntervalAmpliGainTiltMin cooIntervalAmpliGainTiltMax cooIntervalAmpliGainTiltAvg cooOtsControllerIAmpliGain cooOtsControllerIAmpliTilt cooOtsControllerIAmpliGainRange cooOtsControllerISafetyControlMode cooOtsControllerIAmpliOsri cooOtsControllerEAmpliGain cooOtsControllerEAmpliTilt cooOtsControllerEAmpliGainRange cooOtsControllerESafetyControlMode cooOtsControllerEAmpliOsri cooOtsControllerTotLCTXPower cooOtsControllerTotLCRXPower cooOtsControllerIForceApr cooOtsControllerEForceApr cooOtsControllerBrPower cooOtsControllerLedState cooOtsControllerEAmpliBrRatio cooOtsControllerAmpliControlModeConfigVal cooOtsControllerEAmpliPowerConfigVal cooOtsControllerTemperature cooOtsControllerVoltage cooOtsControllerTransceiverVendorInfo
The collection of objects to provide information related to the
optical OTS characteristics for interfaces of ifType
opticalChannel(196).
.1.3.6.1.4.1.9.9.834.2.2.1
The collection of objects to give information related to the
optical OTS-OCH characteristics for interfaces of ifType
opticalChannel(196).
.1.3.6.1.4.1.9.9.834.2.2.2
The collection of objects to allow configurations and give
information related to the optical OTS characteristics
for interfaces of ifType opticalChannel(196).
.1.3.6.1.4.1.9.9.834.2.2.3
The collection of objects to allow configurations and give
information related to the optical OTS-OCH characteristics
for interfaces of ifType opticalChannel(196).
.1.3.6.1.4.1.9.9.834.2.2.4
The collection of objects used for monitoring the threshold
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(196).
.1.3.6.1.4.1.9.9.834.2.2.5
The collection of objects used for monitoring the current
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(196) in a current interval.
.1.3.6.1.4.1.9.9.834.2.2.6
The collection of objects used for monitoring the interval
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(196) in a given interval.
.1.3.6.1.4.1.9.9.834.2.2.7
The collection of objects to enable the notification
generations upon an interface's alarms status change on optics OTS
layer.
.1.3.6.1.4.1.9.9.834.2.2.8
The optical status change notifications whenever the
alarms status of optical OTS layer on an interface changes.
.1.3.6.1.4.1.9.9.834.2.2.9
The optical status change notifications whenever the
alarms status of optical OTS-OCH layer on an interface changes.
.1.3.6.1.4.1.9.9.834.2.2.10
The optical equipment notifications whenever the
alarm is generated.
.1.3.6.1.4.1.9.9.834.2.2.11
The collection of objects used for monitoring the total power
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(196).
.1.3.6.1.4.1.9.9.834.2.2.12
The collection of objects to enable the notification
generations upon an interface's alarms status change on optics
OTS-OCH layer.
.1.3.6.1.4.1.9.9.834.2.2.13
The collection of objects to allow configurations and give
information related to the optical OTS characteristics
for interfaces of ifType opticalTransport(196) using the
controller2 table.
.1.3.6.1.4.1.9.9.834.2.2.14
Compliance Statements (1)

OID .1.3.6.1.4.1.9.9.834.2.1.1
The compliance statement for platforms that monitor the
parameters for the optical interfaces.
Required groups
mandatory cooOtsGroup
optional cooOtsOchGroup The collection of objects to allow configurations and give
information related to the optical layer characteristics
for interfaces of ifType opticalChannel(196).
optional cooOtsControllerGroup The collection of objects to allow configurations and give
information related to the optical layer characteristics
for interfaces of ifType opticalChannel(196).
optional cooOtsController2Group The collection of objects to allow configurations and give
information related to the optical OTS characteristics
for interfaces of ifType opticalTransport(196) using the
controller2 table.
optional cooOtsOchControllerGroup The collection of objects to allow configurations and give
information related to the optical layer characteristics
for interfaces of ifType opticalChannel(196).
optional cooOtsThresholdGroup The collection of objects used for monitoring the threshold
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(196).
optional cooOtsCurrentGroup The collection of objects used for monitoring the current
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(196) in a current interval.
optional cooOtsIntervalGroup The collection of objects used for monitoring the interval
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(196) in a given interval.
optional cooOtsNotifEnableGroup The collection of objects to enable the notification
generations upon an interface's alarms status change on optics
layer.
optional cooOtsNotifGroup The optical status change notifications whenever the
alarms status of optical OTS layer on an interface changes.
optional cooOtsOchNotifGroup The optical status change notifications whenever the
alarms status of optical OTS-OCH layer on an interface changes.
optional cooOtsEquipmentAlarmInfoGroup The optical equipment alarm notifications whenever the
equipment failed alarm is detected.
optional cooOtsPowerGroup The collection of objects used for monitoring the total power
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(196).
optional cooOtsOchNotifEnableGroup The collection of objects to enable the notification generations
upon an interface's alarms status change on optics OTS-OCH
layer.
Notifications / Traps (3)
NameOIDDescription
.1.3.6.1.4.1.9.9.834.0.1
This notification is generated when the value of
cooOtsControllerStatus changes.
The varbind for this notification indicates the ifIndex,
ifname of the OTS interface as well as controller port type and status.
.1.3.6.1.4.1.9.9.834.0.2
This notification is generated when the value of
cooOtsOchControllerStatus changes.
The varbind for this notification indicates the ifIndex,
ifname of the OTS-OCH interface as well as controller port type
and status.
.1.3.6.1.4.1.9.9.834.0.3
This notification is generated whenever the optical equipment
alarm is generated.