CISCO-NETFLOW-LITE-MIB Table View

Contains Netflow-lite exporter entries. A row is created for
each Netflow-lite exporter configured in a device.
A row cannot be removed when it's being used in 
cnlIfMonitorEntry.

cnlExporterEntry row .1.3.6.1.4.1.9.9.776.1.1.2.1

An entry containing the management information of Netflow-lite
exporter.

Indexes

cnlExporterName

Column	Syntax	OID
cnlExporterName Exporter name identifying a particular Netflow-lite exporter configuration.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.9.776.1.1.2.1.1
cnlExportAddrType Specifies the type of IP address used by cnlExportDestinationAddr and cnlExportSourceAddr.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.776.1.1.2.1.2
cnlExportDestinationAddr Specifies the Netflow-lite collector's IP address, used to construct the L3 header of export packet. The type of this address is determined by the cnlExportAddrType object.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.776.1.1.2.1.3
cnlExportDestinationUdpPort Specifies the collector's UDP port, on which the remote collector can listen for export packets.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.776.1.1.2.1.4
cnlExportDestinationUdpLoadShare Specifies the number of destination UDP ports used for load sharing. The export datagrams will use a UDP destination port number that round robins between a set of consecutive destination UDP port numbers starting wi…	Unsigned32r/w Constraints: range: 1-16	.1.3.6.1.4.1.9.9.776.1.1.2.1.5
cnlExportSourceAddr Specifies the source IP address used in export packet L3 header. The type of this address is determined by the cnlExportAddrType object.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.776.1.1.2.1.6
cnlExportSourceUdpPort Specifies the source UDP port used in export packets.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.776.1.1.2.1.7
cnlExportVrf Specifies the Virtual Routing and Forwarding (VRF) domain of the collector. A zero length string indicates that there is no VRF domain configured and the default VRF domain is used.	CISCO-TCCiscoVrfNamer/w Type Constraints: range: 0..32	.1.3.6.1.4.1.9.9.776.1.1.2.1.8
cnlExportTtl Specifies the Time To Live (TTL) value to be used in the export packet header.	Unsigned32r/w Constraints: range: 1-254	.1.3.6.1.4.1.9.9.776.1.1.2.1.9
cnlExportCos Specifies the Class of Service (CoS) value of the export packet header.	CISCO-TCLayer2Cosr/w Type Constraints: range: 0..7	.1.3.6.1.4.1.9.9.776.1.1.2.1.10
cnlExportDscp Specifies the Differentiated Services Code-Point (DSCP) value of the export packet header.	DIFFSERV-DSCP-TCDscpr/w Type Constraints: range: 0..63	.1.3.6.1.4.1.9.9.776.1.1.2.1.11
cnlExportTemplateTimeout The maximum time the template data can exist in queue before it's exported out.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.1.2.1.12
cnlExportSamplerTableTimeout The maximum time the sampler table data can exist in queue before it's exported out.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.1.2.1.13
cnlExportInterfaceTableTimeout The maximum time the interface table data can exist in queue table before it's exported out.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.1.2.1.14
cnlExportProtocol Specifies the Netflow data export protocol. ipFix: The IP Flow Information Export protocol. netflowV9: Netflow services export protocol version 9.	Enumerationr/w Enumerated Values: 1 ipFix 2 netflowV9	.1.3.6.1.4.1.9.9.776.1.1.2.1.15
cnlPacketExported The total number of packets which have been exported.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.776.1.1.2.1.16
cnlExporterStorageType Specifies the storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.776.1.1.2.1.17
cnlExporterRowStatus The status of this conceptual row. The new entry can be created by setting this object value to 'createAndGo'. The entry may not be deleted via by setting its value to 'destroy' if the valu…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.776.1.1.2.1.18

Contains Netflow-lite sampler entries. A row is created 
for each Netflow-lite sampler configured in a device.
          
A row cannot be removed when it's being used in 
cnlIfMonitorEntry.

cnlSamplerEntry row .1.3.6.1.4.1.9.9.776.1.2.2.1

An entry containing the management information of Netflow-lite
sampler.

Indexes

cnlSamplerName

Column	Syntax	OID
cnlSamplerName Sampler name identifying a particular Netflow-lite sampler configuration.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.9.776.1.2.2.1.1
cnlSamplerPacketRate Specifies packet being sampled at 1-in-N packets rate in powers of 2, for example, 1-in-64.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.2.2.1.2
cnlSamplerPacketSectionSize Specifies length of packet section that was extracted for export.	bytesSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.2.2.1.3
cnlSamplerPacketOffset Specifies the starting offset of packet section that was extracted for export.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.2.2.1.4
cnlSamplerStorageType Specifies the storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.776.1.2.2.1.5
cnlSamplerRowStatus The status of this conceptual row. The new entry can be created by setting this object value to 'createAndGo'. The entry may not be deleted via by setting its value to 'destroy' if this sam…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.776.1.2.2.1.6

Contains Netflow-lite monitor entries. A row is created to
activate traffic sampling on the interface.

cnlIfMonitorEntry row .1.3.6.1.4.1.9.9.776.1.3.1.1

An entry containing the management information of Netflow-lite
monitor.

Indexes

IF-MIBifIndex cnlIfMonitorSessionName

Column	Syntax	OID
cnlIfMonitorSessionName Monitor session name identifying a particular Netflow-lite monitor configuration.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.9.776.1.3.1.1.1
cnlIfMonitorActiveStatus Indicates current monitor is in active status or not. active(1) : means monitor parameters meet mandatory requirement, it is in active mode. inactive(2): means monitor is not in active mode.	Enumeration Enumerated Values: 1 active 2 inactive	.1.3.6.1.4.1.9.9.776.1.3.1.1.2
cnlIfSamplerName Specifies one existing Sampler entry by name, the sampler object value will be used to configure interface sampling parameters.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.776.1.3.1.1.3
cnlIfExporterName Specifies one existing Exporter entry by name, the exporter object value will be used to construct export packet header	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.776.1.3.1.1.4
cnlIfAveragePacketSize Specifies average packet size expected at the observation point. Used in tuning the time based sampling interval. Default value 0, indicates system automatically calculate the average packet size at the interface.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.3.1.1.5
cnlIfAveragePacketSizeObserved The average packet size calculated at the interface. Used in tuning the time based sampling interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.3.1.1.6
cnlIfAveragePacketSizeUsed The average packet size used in tuning the time based in tuning sampling performance.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.776.1.3.1.1.7
cnlIfMonitorPktsObserved The total number of packets is observed at the interface.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.776.1.3.1.1.8
cnlIfMonitorPktsExported The total number of exported packets for this monitor session.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.776.1.3.1.1.9
cnlIfMonitorPktsDropped The total number of dropped packets for this monitor session.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.776.1.3.1.1.10
cnlIfMonitorStorageType Specifies the storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.776.1.3.1.1.11
cnlIfMonitorRowStatus The status of this conceptual row. The new entry can be created by setting this object value to 'createAndGo'. The entry can be deleted via by setting its value to 'destroy'. …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.776.1.3.1.1.12