CISCO-FCOE-MIB Table View

This table facilitates configuration of FCoE parameters
on a per Fibre Channel management instance.

cfcoeCfgEntry row .1.3.6.1.4.1.9.9.673.1.1.1.1

There is one entry in this table for each
Fibre Channel management instance.

Indexes

FC-MGMT-MIBfcmInstanceIndex FC-MGMT-MIBfcmSwitchIndex

Column	Syntax	OID
cfcoeCfgFcmap This object configures the FC-MAP value used by the FCF when operating in FPMA mode. The default value is 0EFC00h, as written in the standard.	OctetStringr/w Constraints: range: 3-3	.1.3.6.1.4.1.9.9.673.1.1.1.1.1
cfcoeCfgDynamicVfcCreation This object allows the user to enable (TRUE) or disable (FALSE) dynamic VFC interface creation on the FCF. When set to TRUE VFC interfaces are dynamically created when a FIP based FLOGI or ELP request is received.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.673.1.1.1.1.2
cfcoeCfgDynamicVfcAgeTimer This ageing timer (in seconds) is used by the FCF to age out dynamically created VFC interfaces. The default value is 300 seconds.	Unsigned32r/w Constraints: range: 10-1000000	.1.3.6.1.4.1.9.9.673.1.1.1.1.3
cfcoeCfgDefaultFCFPriority The FIP priority value advertised by the FCF to ENodes by default. cfcoeStaticVfcFCFPriority configured for a VFC interface overrides this setting for the ENode associated with the VFC.	Unsigned32r/w Constraints: range: 0-255	.1.3.6.1.4.1.9.9.673.1.1.1.1.4
cfcoeCfgDATov The Discovery_Advertisement_Timeout value configured for the FCF. This is used as the timeout value in seconds by the FCF to send periodic Discovery Advertisements.	Unsigned32r/w Constraints: range: 1-60	.1.3.6.1.4.1.9.9.673.1.1.1.1.5
cfcoeCfgAddressingMode Addressing mode(s) supported by the FCF. Implementations should fail set requests for unsupported modes.	Enumerationr/w Enumerated Values: 1 fpma 2 spma 3 both	.1.3.6.1.4.1.9.9.673.1.1.1.1.6

This table facilitates configuration of VLAN and Fabric (VSAN)
associations in an FCoE network. FCoE forwarding for a fabric 
is over a VLAN in a L2 Ethernet network.  That is, reachability
between the ENode/remote-FCF and an FCF for a given fabric is
determined by the reachability provided by the Ethernet network
on the corresponding VLAN. 
          
An active entry in this table indicates the VLAN that is used 
to transport FCoE traffic for a certain VSAN.
          
Some implmentations may allow traffic from only one VSAN to be
transported over a given VLAN. Such implmentations should 
prevent multiple entries with the same VLAN ID or the VSAN ID 
from being created in this table.
          
Modifying existing VLAN-VSAN associations is not supported.
Entries must be deleted first and then recreated.

cfcoeVLANEntry row .1.3.6.1.4.1.9.9.673.1.1.2.1

There is one entry in this table for each VLAN that is
designated to transport FCoE traffic for a given fabric
(VSAN).

Indexes

FC-MGMT-MIBfcmInstanceIndex FC-MGMT-MIBfcmSwitchIndex cfcoeVLANIndex cfcoeFabricIndex

Column	Syntax	OID
cfcoeVLANIndex This object identifies the VLAN ID that FCoE FCF function is being enabled for.	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.9.9.673.1.1.2.1.1
cfcoeFabricIndex This object identifies the Fabric Index of the VSAN traffic for which can be transported over the VLAN identified by cfcoeVLANIndex.	T11-TC-MIBT11FabricIndex Type Constraints: range: 0..4095	.1.3.6.1.4.1.9.9.673.1.1.2.1.2
cfcoeVLANOperState Operational state of this VLAN-VSAN association entry. The 'up' state is achieved when both the VSAN and VLAN are valid.	Enumeration Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.9.9.673.1.1.2.1.3
cfcoeVLANRowStatus The status of this conceptual row. The RowStatus becomes active on successful creation of an entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.673.1.1.2.1.4

This table facilitates the creation and deletion of static
VFC interfaces. While VFCs can be dynamically created based on
FIP FLOGI/ELP requests users may want to associate certain
pre-configured policy for a particular ENode or a remote-FCF.
In such cases static VFC creation becomes necessary. In addition
to creating a static VFC it also needs to be associated to an
ENode or remote-FCF. The VFC binding provides such an 
associaton. Binding may occur after a VFC is created.

cfcoeStaticVfcEntry row .1.3.6.1.4.1.9.9.673.1.1.3.1

There is one entry in this table for each statically created
VFC Interface.

Indexes

FC-MGMT-MIBfcmInstanceIndex FC-MGMT-MIBfcmSwitchIndex cfcoeStaticVfcIndex

Column	Syntax	OID
cfcoeStaticVfcIndex This index uniquely identifies a static VFC entry in this table.	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.4.1.9.9.673.1.1.3.1.1
cfcoeStaticVfcFCFPriority If this VFC is for a VF_Port this object is used to configure FCF priority to be advertised to the ENode associated with the VFC.	Unsigned32r/w Constraints: range: 0-255	.1.3.6.1.4.1.9.9.673.1.1.3.1.2
cfcoeStaticVfcBindType The mechanism to identify the ENode associated with this VFC if it is of type VF_Port or to identify the remote-FCF associated with this VFC if it is of type VE_Port.	VfcBindTyper/w Type Values: 1 interfaceIndex 2 macAddress	.1.3.6.1.4.1.9.9.673.1.1.3.1.3
cfcoeStaticVfcBindIfIndex This object allows for configuration of ifIndex of the ethernet interface over which the FCF reaches the ENode or the remote-FCF that this VFC identifies. This object is to be used only when the ENode or the remote-FCF …	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.9.9.673.1.1.3.1.4
cfcoeStaticVfcBindMACAddress This object allows the user to configure MAC address of the ENode or the remote-FCF that this VFC interface identifies. An ENode or remote-FCF is associated to this VFC only if the source MAC address in the FIP frames m…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.673.1.1.3.1.5
cfcoeStaticVfcIfIndex The ifIndex of this virtual FC interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.673.1.1.3.1.6
cfcoeStaticVfcCreationTime The timestamp of this entry's creation time.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.673.1.1.3.1.7
cfcoeStaticVfcFailureCause The cause of failure for the last bind operation. This object will be zero length if and only if the bind is successful.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.673.1.1.3.1.8
cfcoeStaticVfcRowStatus The status of this conceptual row. The RowStatus becomes active on successful creation of a virtual interface. The VFC must be bound before it can become operational.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.673.1.1.3.1.9

The (conceptual) table containing the interfaces on an
Ethernet bridge that are directly connected to ENodes.
A FIP Snooping bridge will automatically configure ACLs on
these interfaces based on FIP login requests and responses.

cfcoeEnodeIntfEntry row .1.3.6.1.4.1.9.9.673.1.2.3.1

An entry (conceptual row) in the cfcoeEnodeIntfTable,
representing an interface directly connected to an ENode
on the Ethernet Bridge.

Indexes

cfcoeEnodeIntfIfIndex

Column	Syntax	OID
cfcoeEnodeIntfIfIndex The ifIndex of the interface on the Ethernet bridge connected to an Enode.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.673.1.2.3.1.1
cfcoeEnodeIntfRowStatus The status of this conceptual row.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.673.1.2.3.1.2