CISCO-BSC-MIB Table View

A list of port (serial interfaces) which have been configured 
to support a BSC BSTUN group.

bscPortEntry row .1.3.6.1.4.1.9.9.36.1.1.1.1

Status and parameter values for a port.

Indexes

IF-MIBifIndex

Column	Syntax	OID
bscPortRole The router's DLC role to the attached node. If the bscPortRole is primary, this implies that the port is connected to a remote secondary device. If the role is generic, this indicates that the port will be running fram…	Enumeration Enumerated Values: 1 primary 2 secondary 3 contention 4 dialContention 5 generic	.1.3.6.1.4.1.9.9.36.1.1.1.1.1
bscPortCodeSet The code set used for the line controls.	Enumeration Enumerated Values: 1 ebcdic 2 ascii	.1.3.6.1.4.1.9.9.36.1.1.1.1.2
bscPortPause For primary, it is the minimum time to be taken for a cycle round the active poll table; if this time has not elapsed when the bottom of the poll table is reached, then polling will pause until this timer expires. A…	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.9.9.36.1.1.1.1.3
bscPortServlim This parameter is valid for primary only. It is the number of times the active poll table will be cycled before a non-responding control unit will be polled. The default is 3.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.9.9.36.1.1.1.1.4
bscPortPollTimeout This parameter is valid for primary only. It is the time that the primary will wait for a response to a poll or select. The units are tenths of a second. The default is 10 (1 second).	Integer32 Constraints: range: 1-100	.1.3.6.1.4.1.9.9.36.1.1.1.1.5
bscPortRecoveryRetries This is the number of times that a recovery sequence will be retried before the connection is considered to have failed. The default is 5.	Integer32 Constraints: range: 1-100	.1.3.6.1.4.1.9.9.36.1.1.1.1.6
bscPortUnknownControlUnitsReceived Count of frames received from the serial interface with an unsupported control unit address. If this value is non-zero it indicates a problem in the configuration.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.1.1.1.7
bscPortSoftErrors Count of soft errors; these are errors which have been recovered. This includes CRC errors received, frames which were retransmitted for any reason (NAK received or the wrong ACK received), etc. This count is a measu…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.1.1.1.8
bscPortHardErrors Count of hard errors; these are errors which have not been recovered after bscPortRecoveryRetries number of retries, and therefore the connection has been terminated. These errors could be caused by a hardware error i…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.1.1.1.9
bscPortProtocolViolations Count of protocol violations. This counter is incremented when an unexpected BSC Data Link Control character is received from the remote device; that is, the control character is invalid in the current state of the lo…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.1.1.1.10
bscPortHostTimeout This parameter is valid for interfaces configured secondary which additionally are running local-acknowledgement. If the configuration does not match the value will be shown as zero. It is the time the interface will w…	decisecondsInteger32 Constraints: range: 30-3000	.1.3.6.1.4.1.9.9.36.1.1.1.1.11
bscPortSpecPoll This parameter is valid for primary, local-acknowledgement interfaces only. It is set to TRUE when the interface is configured to treat specific polls as general polls. If the configuration cannot support this value, …	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.36.1.1.1.1.12
bscPortVirtualAddress This parameter is valid for contention only. It is the address to be used for this interface when the remote peer router is being used as a concentrator. The default is 01.	Integer32 Constraints: range: 1-254	.1.3.6.1.4.1.9.9.36.1.1.1.1.13
bscPortContentionDialTimeout This parameter is valid for dialContention only. It is the amount of time an interface can be quiescent before return the interface to the dial-in pool. The default is 5 seconds.	secondsInteger32 Constraints: range: 2-30	.1.3.6.1.4.1.9.9.36.1.1.1.1.14

A table containing information about specific 
Control Units.

bscCUEntry row .1.3.6.1.4.1.9.9.36.1.2.1.1

The information regarding a single Control Unit.

Indexes

IF-MIBifIndex bscCUAddress

Column	Syntax	OID
bscCUAddress This value is the poll address of the BSC Control Unit. This address must be unique within a BSTUN Group.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.9.9.36.1.2.1.1.1
bscCUState State of the BSC Control Unit; when active this indicates that the remote Control Unit is polling or responding to polls.	Enumeration Enumerated Values: 1 inactive 2 active	.1.3.6.1.4.1.9.9.36.1.2.1.1.2
bscCUBytesSent Count of sent bytes (octets). Includes all control characters.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.3
bscCUBytesReceived Count of received bytes (octets). Includes all control characters.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.4
bscCUTotalFramesSent Count of sent frames (blocks). Includes all control frames.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.5
bscCUTotalFramesReceived Count of received frames (blocks). Includes all control frames.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.6
bscCUDataFramesSent Count of sent data frames (blocks).	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.7
bscCUDataFramesReceived Count of received data frames (blocks).	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.8
bscCUSoftErrors Count of soft errors; these are errors which have been recovered. This includes CRC errors received, frames which were retransmitted for any reason (NAK received or the wrong ACK received), etc. This count is a measu…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.9
bscCUHardErrors Count of hard errors; these are errors which have not been recovered after bscPortRecoveryRetries number of retries, and therefore the connection has been terminated. These errors could be caused by a hardware error i…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.10
bscCUProtocolViolations Count of protocol violations. This counter is incremented when an unexpected BSC Data Link Control character is received from the remote device; that is, the control character is invalid in the current state of the lo…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.36.1.2.1.1.11

List of all addresses configured by the bsc
extended-address command. This applies only to interfaces
with an ifType of 'bsc'. The address entries must be
unique per interface.

bscExtAddressEntry row .1.3.6.1.4.1.9.9.36.1.3.1.1

The information regarding a single extended addresses.

Indexes

IF-MIBifIndex bscExtPollAddress

Column	Syntax	OID
bscExtPollAddress The poll address of the station configured by the bsc extended-address command.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.9.9.36.1.3.1.1.1
bscExtSelectAddress The select address of the station configured by the bsc extended-address command.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.9.9.36.1.3.1.1.2