CISCO-APS-EXT-MIB
The Cisco APS Extension MIB extends the Cisco APS MIB
in order to a) support path APS architectures and
b) support interfaces other than SONET (e.g. Cisco
CDL).
For configuration and monitoring of APS for CDL interfaces,
all objects and notifications in the Cisco APS MIB apply,
with the exception of the following:
- cApsStatusK1K2Rcv and cApsStatusK1K2Trans in
cApsStatusEntry,
- cApsConfigSdBerThreshold and cApsConfigSfBerThreshold
in cApsConfigEntry,
- cApsChanStatusSignalDegrades and
cApsChanStatusSignalFailures in cApsChanStatusEntry,
- cApsStatusFEPLFs in cApsStatusEntry,
- cApsEventFEPLF.
Whenever the description of an object in the Cisco APS MIB
refers to a SONET LTE interface, this applies to CDL
terminating interfaces as well. CDL interfaces have
ifType values other than 'sonet'.
For SONET path APS support, whenever the description of an
object in the Cisco APS MIB refers to a SONET LTE
interface, this applies to SONET PTE interfaces as well.
SONET PTE interfaces have ifType values 'sonetPath'.
- Source file
CISCO-APS-EXT-MIB- Last revised
- Identity
cApsExtMIB- Base OID
1.3.6.1.4.1.9.10.72
Imported Objects
| CISCO-APS-MIB | cApsChanConfigEntry cApsChanStatusEntry cApsConfigEntry CApsK1K2 cApsStatusEntry |
| CISCO-SMI | ciscoExperiment |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE (no object page) OBJECT-GROUP (no object page) |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY (no object page) OBJECT-TYPE (no object page) |
| SNMPv2-TC | TEXTUAL-CONVENTION (no object page) TruthValue |
Net-SNMP examples using the cisco MIB directory Show commands
These commands use the standard Observium installation path and load the selected MIB variant before the RFC and Net-SNMP directories.
Translate the module identity
/usr/bin/snmptranslate -Pud -Ir -On -m 'CISCO-APS-EXT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'CISCO-APS-EXT-MIB::cApsExtMIB'
Walk the MIB subtree
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-APS-EXT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-APS-EXT-MIB::cApsExtMIB'
Objects (38)
Showing 38 of 38 objects
Object legend
Object type
Icons distinguish tables, entry rows, columns, scalars, and structural nodes.
SNMPv2-TCTruthValue
Syntax
Blue badges identify the value syntax. Connected badges read as defining module and convention.
IF-MIBifIndex
Table index
Green identifies an index object; yellow names its module when the index is defined elsewhere.
r/w
deprecated
obsolete
Access and status
r/w means read-write. Grey labels mark definitions retained for compatibility.
OBS ✓
Observium use
The indicator appears only when Observium directly references that object.
ifOperStatus
.1.3.6.1.2.1…
Names and OIDs
Object names link to their detail pages. Hover or focus a linked name or badge for available definition details.
.1.3.6.1.4.1.9.10.72 |
||
.1.3.6.1.4.1.9.10.72.1 |
||
.1.3.6.1.4.1.9.10.72.1.1 |
||
.1.3.6.1.4.1.9.10.72.1.2 |
||
.1.3.6.1.4.1.9.10.72.1.2.1 |
||
|
|
Enumeration
|
.1.3.6.1.4.1.9.10.72.1.2.1.1 |
|
OctetString
|
.1.3.6.1.4.1.9.10.72.1.2.1.10 |
|
.1.3.6.1.4.1.9.10.72.1.2.1.11 |
||
.1.3.6.1.4.1.9.10.72.1.2.1.12 |
||
|
|
Enumeration
|
.1.3.6.1.4.1.9.10.72.1.2.1.2 |
|
Integer32
|
.1.3.6.1.4.1.9.10.72.1.2.1.3 |
|
|
secondsInteger32
|
.1.3.6.1.4.1.9.10.72.1.2.1.4 |
|
|
secondsInteger32
|
.1.3.6.1.4.1.9.10.72.1.2.1.5 |
|
.1.3.6.1.4.1.9.10.72.1.2.1.6 |
||
|
millisecondsInteger32
|
.1.3.6.1.4.1.9.10.72.1.2.1.7 |
|
|
Integer32
|
.1.3.6.1.4.1.9.10.72.1.2.1.8 |
|
|
millisecondsInteger32
|
.1.3.6.1.4.1.9.10.72.1.2.1.9 |
|
.1.3.6.1.4.1.9.10.72.1.3 |
||
.1.3.6.1.4.1.9.10.72.1.3.1 |
||
.1.3.6.1.4.1.9.10.72.1.3.1.1 |
||
.1.3.6.1.4.1.9.10.72.1.3.1.2 |
||
.1.3.6.1.4.1.9.10.72.1.3.1.3 |
||
.1.3.6.1.4.1.9.10.72.1.4 |
||
.1.3.6.1.4.1.9.10.72.1.4.1 |
||
.1.3.6.1.4.1.9.10.72.1.4.1.1 |
||
.1.3.6.1.4.1.9.10.72.1.5 |
||
.1.3.6.1.4.1.9.10.72.1.5.1 |
||
.1.3.6.1.4.1.9.10.72.1.5.1.1 |
||
.1.3.6.1.4.1.9.10.72.1.6 |
||
.1.3.6.1.4.1.9.10.72.1.6.1 |
||
|
OctetString
|
.1.3.6.1.4.1.9.10.72.1.6.1.1 |
|
.1.3.6.1.4.1.9.10.72.1.6.1.2 |
||
.1.3.6.1.4.1.9.10.72.1.6.1.3 |
||
.1.3.6.1.4.1.9.10.72.1.6.1.4 |
||
.1.3.6.1.4.1.9.10.72.1.6.1.5 |
||
.1.3.6.1.4.1.9.10.72.2 |
||
.1.3.6.1.4.1.9.10.72.2.1 |
||
.1.3.6.1.4.1.9.10.72.2.2 |
Dependencies (10) 7 direct · 3 transitive Show tree and compile order Hide dependency details
Each imported module is resolved in the importing module's source directory first, then through the normal default-variant rules.
Dependency tree
Dependency-first compile order
- SNMPv2-SMIrfc
- CISCO-SMIcisco
- SNMPv2-TCrfc
- IANAifType-MIBrfc
- SNMPv2-CONFrfc
- SNMPv2-MIBrfc
- IF-MIBrfc
- SNMP-FRAMEWORK-MIBrfc
- CISCO-APS-MIBcisco
- INET-ADDRESS-MIBrfc
- CISCO-APS-EXT-MIBciscoselected
Type Definitions (3)
| Integer32 |
range: 0..14 |
|
| Enumeration |
none(1)autoSelect(2)dcc(3)apsChannel(4)ip(5)osc(6) |
|
| OctetString |
range: 2 |
Conformance Groups (12)
|
A managed object that controls the generation of APS-related
notifications defined in the CISCO-APS-MIB. |
.1.3.6.1.4.1.9.10.72.2.1.1
|
|
|
An augmentation to cApsConfigTable objects providing
configuration information applicable to path APS architectures. |
.1.3.6.1.4.1.9.10.72.2.1.2
|
|
|
An augmentation to cApsConfigTable objects providing
configuration information applicable to APS groups when Y cable protection is supported. |
.1.3.6.1.4.1.9.10.72.2.1.3
|
|
|
An augmentation to cApsConfigTable objects providing
configuration information applicable to APS groups in which the standby interface is not monitored. |
.1.3.6.1.4.1.9.10.72.2.1.4
|
|
|
An augmentation to cApsStatusTable objects providing status
information applicable to APS groups for CDL. |
.1.3.6.1.4.1.9.10.72.2.1.5
|
|
|
An augmentation to cApsConfigTable objects providing
configuration information to prevent quick successive switchovers. |
.1.3.6.1.4.1.9.10.72.2.1.6
|
|
|
cApsConfigMessageTransport cApsConfigMessageHolddown cApsConfigMessageHolddownCount cApsConfigMessageMaxInterval cApsConfigFarEndGroupName
An augmentation to cApsConfigTable objects providing
configuration information applicable to message transport used to exchange APS protocol messages. |
.1.3.6.1.4.1.9.10.72.2.1.7
|
|
|
An augmentation to cApsConfigTable objects providing
configuration information applicable to APS groups communicating over IP. |
.1.3.6.1.4.1.9.10.72.2.1.8
|
|
|
An augmentation to cApsStatusTable objects providing
status information applicable to message transport used to exchange APS protocol messages. |
.1.3.6.1.4.1.9.10.72.2.1.9
|
|
|
An augmentation to cApsChanStatusTable objects providing
additional status information for channels in APS groups. |
.1.3.6.1.4.1.9.10.72.2.1.10
|
|
|
An augmentation to cApsChanConfigTable objects providing
configuration information of channels in APS groups. |
.1.3.6.1.4.1.9.10.72.2.1.11
|
|
|
cApsChanAssociationTable object provides for all
protection/working channels, the associated working/protection channel IP address. |
.1.3.6.1.4.1.9.10.72.2.1.12
|
Compliance Statements (3)
OID
.1.3.6.1.4.1.9.10.72.2.2.1The compliance statement for augmented APS groups.
Required groups
| mandatory | cApsNotifiesEnableGroup | |
| mandatory | cApsConfigPathExt | |
| optional | cApsConfigYcableExt |
This group is required for entities that implement Y cable protection. |
| optional | cApsConfigSearchExt |
This group is required for entities that do not always monitor the standby interface. |
| optional | cApsStatusCdlExt |
This group is required for entities that support APS on CDL interfaces. |
Object refinements
| Object | Access | Syntax | Description |
|---|---|---|---|
| cApsConfigSpan | readonly | Write access and support for the 'end-to-end' codepoint are not required. |
OID
.1.3.6.1.4.1.9.10.72.2.2.2The compliance statement for augmented APS groups.
Required groups
| mandatory | cApsNotifiesEnableGroup | |
| mandatory | cApsConfigPathExt | |
| optional | cApsConfigYcableExt |
This group is required for entities that implement Y cable protection. |
| optional | cApsConfigSearchExt |
This group is required for entities that do not always monitor the standby interface. |
| optional | cApsStatusCdlExt |
This group is required for entities that support transport of APS messages in the APS channel on CDL interfaces. |
| optional | cApsConfigMessageExt |
This group is required for entities that support APS message transport over data communication channels (DCCs), optical supervisory channels (OSCs), or Data Communication Networks (DCNs). |
| optional | cApsConfigSwitchoverTimerExt | This group is optional. |
| optional | cApsConfigIPExt |
This group is required for entities that support APS message transport over IP. The IP network can consist of any combination of data communication channels (DCCs), optical supervisory channels (OSCs), and Data Communication Networks (DCNs). |
| optional | cApsStatusMessageExt |
This group is required for entities that support APS message transport over data communication channels (DCCs), optical supervisory channels (OSCs), or Data Communication Networks (DCNs). |
| optional | cApsChanStatusRequestExt | This group is optional. |
Object refinements
| Object | Access | Syntax | Description |
|---|---|---|---|
| cApsConfigSpan | readonly | Write access and support for the 'end-to-end' codepoint are not required. |
|
| cApsConfigMessageTransport | readonly | Write access is not required. |
OID
.1.3.6.1.4.1.9.10.72.2.2.3The compliance statement for augmented APS groups.
Required groups
| mandatory | cApsChanConfigExt | |
| mandatory | cApsChanAssociationGroup |