CADANT-CMTS-POLICY-MIB Table View

A table contains SCM access control list information. 
Each physical interface is associated with the access list number defined 
as hjpolAccListNumber in hjpolAccListTable of NETPLANE-POLICY-MIB. With
this information, C4 can permit/deny access usnig access list filtering before 
the packet reach SCM from the specified physical interface.

cadScmAccessEntry row .1.3.6.1.4.1.4998.1.1.35.1.1.1

A conceptual row containing information about SCM access list
for each physical interface.

Indexes

cadScmAccIfIndex

Column	Syntax	OID
cadScmAccIfIndex The value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which SCM access control is applied	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.35.1.1.1.1
cadScmAccListNumber The value of this object identifies entry(or entries) in the hjpolAccListTable. The identified entry(or entries) contains SCM access parameters to be used when filtering traffic from individual interface sent to SCM.	Integer32r/w Constraints: range: 1-99	.1.3.6.1.4.1.4998.1.1.35.1.1.1.2
cadScmAccRowStatus Control Object for row creation and deletion.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.1.1.3

Distribute List In Table

cadDistListInEntry row .1.3.6.1.4.1.4998.1.1.35.1.2.1

A row in Distribute List In table

Indexes

cadDistListInProtocol cadDistListInProtocolProcess cadDistListInIfIndex cadDistListInAccessListNum

Column	Syntax	OID
cadDistListInProtocol Protocol for which distribute list is applied.	CadPolicyProtocol Type Values: 1 other 2 local 3 netmgmt 4 icmp 5 egp 6 ggp 7 hello 8 rip 9 isIs 10 esIs 11 ciscoIgrp 12 bbnSpfIgp 13 ospf 14 bgp 15 idpr 16 ciscoEigrp	.1.3.6.1.4.1.4998.1.1.35.1.2.1.1
cadDistListInProtocolProcess VRF for which distribute list is applied.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4998.1.1.35.1.2.1.2
cadDistListInIfIndex Interface for which distribute list is applied. The value will be 1 if the distribute list is applied to all interfaces.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.35.1.2.1.3
cadDistListInAccessListNum The configured distribute in list refers to the access list specified.	Integer32 Constraints: range: 1-99	.1.3.6.1.4.1.4998.1.1.35.1.2.1.4
cadDistListInAccessListName Name of the access list referred by distribute in list.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.4998.1.1.35.1.2.1.5
cadDistListInStatus The row status variable, used according to row installation and removal conventions. Once access list specified default row status is active.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.2.1.6

A table of rate limiting policies applied to a physical interface.

cadPolicyRateLimitEntry row .1.3.6.1.4.1.4998.1.1.35.1.4.1

An ordered list of the rate limit polices

Indexes

cadPolicyRateLimitIfIndex cadPolicyRateLimitDirection cadPolicyRateLimitIndex

Column	Syntax	OID
cadPolicyRateLimitIfIndex The value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which the rate limit policy is applied	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.35.1.4.1.1
cadPolicyRateLimitDirection Direction of traffic on interface to apply the rate limit policy	CADANT-TCCadIfDirection Type Values: 1 in 2 out	.1.3.6.1.4.1.4998.1.1.35.1.4.1.2
cadPolicyRateLimitIndex Index of rate limit policy. Policies are applied in the order specified by this index value	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.4998.1.1.35.1.4.1.3
cadPolicyRateLimitStatus Create and delete table row entries.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.4.1.4
cadPolicyRateLimitAclType Type of ACL associated with rate limit policy	CADANT-TCCadAclTyper/w Type Values: 0 none 1 std-access-list 2 ext-access-list 3 rate-limit-access-list 4 remark 5 ipv6-access-list	.1.3.6.1.4.1.4998.1.1.35.1.4.1.5
cadPolicyRateLimitAclNum ACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IP traffic matches the policy.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.4.1.6
cadPolicyRateLimitBps Average rate, in bits per second (bps).	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.4.1.7
cadPolicyRateLimitBurstNormal Normal burst size, in bytes. The minimum value is bps divided by 2000.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.4.1.8
cadPolicyRateLimitBurstMax Excess burst size, in bytes. Must be equal to or larger than cadPolicyRateLimitBurstNormal	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.4.1.9
cadPolicyRateLimitConformAction Action to take on packets that conform to the specified rate limit.	CadPolicyRateLimitActionr/w Type Values: 1 transmit 2 drop 3 set-prec-transmit 4 set-dscp-transmit 5 set-priority-transmit	.1.3.6.1.4.1.4998.1.1.35.1.4.1.10
cadPolicyRateLimitConformValue Value to set if action is set-prec-transmit, set-dscp-transmit or set-priority-transmit. For set-priority-transmit,the valid value range is 0-7.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.4998.1.1.35.1.4.1.11
cadPolicyRateLimitExceedAction Action to take on packets that exceed to the specified rate limit.	CadPolicyRateLimitActionr/w Type Values: 1 transmit 2 drop 3 set-prec-transmit 4 set-dscp-transmit 5 set-priority-transmit	.1.3.6.1.4.1.4998.1.1.35.1.4.1.12
cadPolicyRateLimitExceedValue Value to set if action is set-prec-transmit, set-dscp-transmit or set-priority-transmit. For set-priority-transmit,the valid value range is 0-7.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.4998.1.1.35.1.4.1.13
cadPolicyRateLimitClearCounts If set to true, clear the counts in the CadPolicyRateLimitStatusEntry. When read, this field always returns false. The correct way to clear the counts is to first read them, then set ClearCounts to true.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.4.1.14

A table of counts of rate limiting policies
applied to a physical interface.

cadPolicyRateLimitStatusEntry row .1.3.6.1.4.1.4998.1.1.35.1.5.1

Dyanmic status associated with a rate limit policy

Indexes

No indexes recorded

Column	Syntax	OID
cadPolicyRateLimitConformPackets Number of packets conforming to the policy rate	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.5.1.1
cadPolicyRateLimitConformBytes Number of bytes conforming to the policy rate	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.5.1.2
cadPolicyRateLimitExceedPackets Number of packets exceeding to the policy rate	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.5.1.3
cadPolicyRateLimitExceedBytes Number of bytes exceeding to the policy rate	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.5.1.4
cadPolicyRateLimitCurrentBurst The current number of bytes in the burst exceeding the average bps rate	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.5.1.5
cadPolicyRateLimitLastCleared The value of SysUptime when the rate limit counters were last cleared.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.4998.1.1.35.1.5.1.6

A table contains access control list (ACL) information. 
Each row corresponds to an access control entry (ACE),
and each ACL may have multiple ACEs that are applied
in order to the packet being inspected.

cadPolicyAclEntry row .1.3.6.1.4.1.4998.1.1.35.1.6.1

A conceptual row containing information about SCM access list
for each physical interface.

Indexes

cadAclNumber cadAclIndex

Column	Syntax	OID
cadAclNumber IPv6 ACL number. IPv6 ACLs are in the range 200-399. Extended ACL number. Extended ACLs are in the range 100-199. Standard ACLs are in the range 1-99.	Integer32 Constraints: range: 1-399	.1.3.6.1.4.1.4998.1.1.35.1.6.1.1
cadAclIndex Order in which this ACE is used in the ACL.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4998.1.1.35.1.6.1.2
cadAclType Indicates whether this EACE is used as a standard, extended, or remark ACL. The rate-limiting type is not valid for this table. Remark is the only valid type that can be set, standard and extended are set by the age…	CADANT-TCCadAclTyper/w Type Values: 0 none 1 std-access-list 2 ext-access-list 3 rate-limit-access-list 4 remark 5 ipv6-access-list	.1.3.6.1.4.1.4998.1.1.35.1.6.1.3
cadAclStatus RowStatus used to add and remove ACEs. ACEs that contain only remarks should have their status set to notInService and should be created with createAndWait.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.6.1.4
cadAclPermit Permit or Deny the packet when matched.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.6.1.5
cadAclProtocol Protocol number to match	CADANT-TCCadProtocolTyper/w Type Constraints: range: -1..255	.1.3.6.1.4.1.4998.1.1.35.1.6.1.6
cadAclSrcIp Source IP address to match	CADANT-TCInetAddressIPv4or6r/w Type Constraints: range: 0 range: 4 range: 8 range: 16 range: 20	.1.3.6.1.4.1.4998.1.1.35.1.6.1.7
cadAclSrcIpMask Source IP wildcard mask to match. Default to match anything	CADANT-TCInetAddressIPv4or6r/w Type Constraints: range: 0 range: 4 range: 8 range: 16 range: 20	.1.3.6.1.4.1.4998.1.1.35.1.6.1.8
cadAclSrcPortOp Source port condition (lt,gt,eq,ne) to match.	CADANT-TCCadExtAclConditionr/w Type Values: 0 na 1 eq 2 ne 3 lt 4 le 5 gt 6 ge 7 range	.1.3.6.1.4.1.4998.1.1.35.1.6.1.9
cadAclSrcPortLo First Source port number to match. -1 indicates that this field is not used.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.6.1.10
cadAclSrcPortHi Second Source port number to match. -1 indicates that this field is not used.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.6.1.11
cadAclDstIp Destination IP address to match	CADANT-TCInetAddressIPv4or6r/w Type Constraints: range: 0 range: 4 range: 8 range: 16 range: 20	.1.3.6.1.4.1.4998.1.1.35.1.6.1.12
cadAclDstIpMask Destination IP wildcard (inverse) mask to match. Default to match anything.	CADANT-TCInetAddressIPv4or6r/w Type Constraints: range: 0 range: 4 range: 8 range: 16 range: 20	.1.3.6.1.4.1.4998.1.1.35.1.6.1.13
cadAclDstPortOp Destination port condition (lt,gt,eq,ne) to match.	CADANT-TCCadExtAclConditionr/w Type Values: 0 na 1 eq 2 ne 3 lt 4 le 5 gt 6 ge 7 range	.1.3.6.1.4.1.4998.1.1.35.1.6.1.14
cadAclDstPortLo First Destination port number to match. -1 indicates that this field is not used.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.6.1.15
cadAclDstPortHi Second Destination port number to match. -1 indicates that this field is not used	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.6.1.16
cadAclLogging Turn on or off the ACE matching log	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.6.1.17
cadAclProtoType Sub-protocol qualifiers. For protocol type ICMP, this value matches the ICMP message type (0 - 255). For IGMP, this value matches the IGMP message type (0-15). A value of -1 means that this field is not used.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.6.1.18
cadAclProtoCode Sub-protocol qualifiers. For protocol type ICMP, this value matches the ICMP message type code (0 - 255). A value of -1 indicates this value is not used.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.6.1.19
cadAclIpTos Matches the TOS field of the IP header.	CADANT-TCCadIpTosr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4998.1.1.35.1.6.1.20
cadAclIpTosMask Mask to apply to the IpTos object when finding a mactch on the TOS field of the IP header. A value of 0 is used to indicate that the TOS is not used.	CADANT-TCCadIpTosMaskr/w Type Constraints: range: 0 range: 30 range: 224 range: 254..255	.1.3.6.1.4.1.4998.1.1.35.1.6.1.21
cadAclTcpFlags Matches the flags field of the TCP header.	CADANT-TCCadTcpFlagsr/w Type Values: 0 urg 1 ack 2 push 3 rst 4 syn 5 fin	.1.3.6.1.4.1.4998.1.1.35.1.6.1.22
cadAclTcpFlagsMask Mask to apply to the TcpFlags object when finding a mactch on the flags field of the TCP header.	CADANT-TCCadTcpFlagsr/w Type Values: 0 urg 1 ack 2 push 3 rst 4 syn 5 fin	.1.3.6.1.4.1.4998.1.1.35.1.6.1.23
cadAclFragments Indicates whether this EACE applies to noninitial fragments of packets. The default is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.6.1.24
cadAclRemark The comment associated with the access control entry. This is only valid for ACEs of type remark.	CADANT-TCCadAclStringr/w Type Constraints: range: 0..32	.1.3.6.1.4.1.4998.1.1.35.1.6.1.26
cadAclIpAddrType IP Address type	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4998.1.1.35.1.6.1.27

A table contains the access list information associated with the 
community string. Each community string defined in snmpCommunithTable 
can be configured with one access list number. C4 can permit/deny access 
usnig access list filtering. Filtering will occur in software, after 
the SNMP traffic passed through the OSE protocol stack and received by 
the agent. Standard ACLs will be used to enforce the access restrictions

cadSnmpCommAccessEntry row .1.3.6.1.4.1.4998.1.1.35.1.7.1

A conceptual row containing information about access list filtering
associated with community string.

Indexes

cadSnmpCommAccessName

Column	Syntax	OID
cadSnmpCommAccessName The index value that uniquely identifies an entry in snmpCommunityTable.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.4998.1.1.35.1.7.1.1
cadSnmpCommAccessList The value of this object identifies entry (or entries) in the cadPolicyAclTable. The identified entry (or entries) contains access parameters to be used when filtering traffic sent to SNMP agent.	Integer32r/w Constraints: range: 1-99	.1.3.6.1.4.1.4998.1.1.35.1.7.1.2
cadSnmpCommAccessStatus Control Object for row creation and deletion.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.7.1.3

A table of access group policies applied to a physical interface.

cadPolicyAccessGroupEntry row .1.3.6.1.4.1.4998.1.1.35.1.8.1

An ordered list of the access group polices

Indexes

cadPolicyAccessGroupIfIndex cadPolicyAccessGroupDirection

Column	Syntax	OID
cadPolicyAccessGroupIfIndex The value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which the access group policy is applied	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.35.1.8.1.1
cadPolicyAccessGroupDirection Direction of traffic on interface to apply the access group policy	CADANT-TCCadIfDirection Type Values: 1 in 2 out	.1.3.6.1.4.1.4998.1.1.35.1.8.1.2
cadPolicyAccessGroupStatus This table supports sets of createAndGo(4) and destroy(6)	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.8.1.3
cadPolicyAccessGroupIpv4AclNum ACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IPv4 traffic matches the policy.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.8.1.4
cadPolicyAccessGroupClearCounts If set to true, clear the counts in the CadPolicyAccessGroupStatusEntry. When read, this field always returns false. The correct way to clear the counts is to first read them, then set ClearCounts to true.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.8.1.5
cadPolicyAccessGroupIpv6AclNum ACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IPv6 traffic matches the policy.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.35.1.8.1.6
cadPolicyAccessGroupIpv6AclName ACL name.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.35.1.8.1.7

A table of counts of rate limiting policies
applied to a physical interface.

cadPolicyAccessGroupStatusEntry row .1.3.6.1.4.1.4998.1.1.35.1.9.1

Dyanmic status associated with a rate limit policy

Indexes

No indexes recorded

Column	Syntax	OID
cadPolicyAccessGroupPermitPackets Number of packets conforming to the access group policy permit ACL	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.9.1.1
cadPolicyAccessGroupDenyPackets Number of packets conforming to the access group policy deny ACL	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.9.1.2
cadPolicyAccessGroupLastCleared The value of SysUptime when the access group policy counters were last cleared.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.4998.1.1.35.1.9.1.3

Prefix List Table

cadPolicyPfxListEntry row .1.3.6.1.4.1.4998.1.1.35.1.11.1

A row in Prefix list table

Indexes

cadPolicyPfxListNumber cadPolicyPfxListName cadPolicyPfxListSeqNumber cadPolicyPfxListAfi cadPolicyPfxListSafi cadPolicyPfxListIpAddress cadPolicyPfxListIpAddMaskLen cadPolicyPfxListMaskGeValue cadPolicyPfxListMaskLeValue

Column	Syntax	OID
cadPolicyPfxListNumber Prefix list is identified by number value of 0 should be passed for this object if prefix list is configured by name	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4998.1.1.35.1.11.1.1
cadPolicyPfxListName Name of prefix list.Null value is assigned to this Object if the prefix list is identified by number	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.35.1.11.1.2
cadPolicyPfxListSeqNumber A sequence in the prefix list is identified by sequence number. If no sequence is specified defalut sequence of 5 is assumend. IF one more sequence is configured sequence number 10 is assigned (multiples of 5)	Integer32 Constraints: range: 5-2147483645	.1.3.6.1.4.1.4998.1.1.35.1.11.1.3
cadPolicyPfxListIpAddress This is the source ipv4 or ipv6 address on which the filtering needs to be applied	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.4998.1.1.35.1.11.1.4
cadPolicyPfxListIpAddMaskLen Mask length of the Source IP address	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.35.1.11.1.5
cadPolicyPfxListMaskGeValue If the received route matches the source address and the mask length is greater than the value specified, apply the specified action to the route	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.35.1.11.1.6
cadPolicyPfxListMaskLeValue This value specifies if the received route mask length is less the value specified here do the action specified (permit/deny)	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.35.1.11.1.7
cadPolicyPfxListAction specifies the action to be taken. Possible actions include permit(1) and deny(2)	CadPolicyActionr/w Type Constraints: range: 1..2	.1.3.6.1.4.1.4998.1.1.35.1.11.1.8
cadPolicyPfxListStatus The row status variable, used according to row installation and removal conventions.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.11.1.9
cadPolicyPfxListAfi This is the Address Family Identifier (AFI) of the prefix that will follow. Only IPv4 or IPv6 prefix-list will be supported.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4998.1.1.35.1.11.1.10
cadPolicyPfxListSafi This is the Subsequent Address Family Identifier (SAFI) of the prefix that will follow.	Enumeration Enumerated Values: 1 unicast 2 multicast 3 both 128 mplsBgpVpn	.1.3.6.1.4.1.4998.1.1.35.1.11.1.11

Distribute List Out Table

cadPolicyDistListOutEntry row .1.3.6.1.4.1.4998.1.1.35.1.12.1

A row in Distribute List Out table

Indexes

cadPolicyDistListOutSrcProtocol cadPolicyDistListOutSrcProtocolProcess cadPolicyDistListOutRoutingProtocol cadPolicyDistListOutRoutingProcess cadPolicyDistListOutAutonomousSystemNum cadPolicyDistListOutIfIndex cadPolicyDistListOutAccessListNum

Column	Syntax	OID
cadPolicyDistListOutSrcProtocol Source Protocol under which distribute list is configured.	CadPolicyProtocol Type Values: 1 other 2 local 3 netmgmt 4 icmp 5 egp 6 ggp 7 hello 8 rip 9 isIs 10 esIs 11 ciscoIgrp 12 bbnSpfIgp 13 ospf 14 bgp 15 idpr 16 ciscoEigrp	.1.3.6.1.4.1.4998.1.1.35.1.12.1.1
cadPolicyDistListOutSrcProtocolProcess Source VRF ID under which distribute list is configured.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4998.1.1.35.1.12.1.2
cadPolicyDistListOutRoutingProtocol Destination Protocol to which routes need to be sent.	CadPolicyProtocol Type Values: 1 other 2 local 3 netmgmt 4 icmp 5 egp 6 ggp 7 hello 8 rip 9 isIs 10 esIs 11 ciscoIgrp 12 bbnSpfIgp 13 ospf 14 bgp 15 idpr 16 ciscoEigrp	.1.3.6.1.4.1.4998.1.1.35.1.12.1.3
cadPolicyDistListOutRoutingProcess Destination VRF ID under which distribute list is configured.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4998.1.1.35.1.12.1.4
cadPolicyDistListOutAutonomousSystemNum Autonomous system number of BGP to which routes need to be redistributed. If destination protocol is BGP appropriate AS number needs to be filled for this object. Otherwise set a value of 1 for this object.	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.4998.1.1.35.1.12.1.5
cadPolicyDistListOutAccessListNum The configured distribute out list refers to the access list specified. The access list number must be in the range of 1 - 99	Integer32 Constraints: range: 1-99	.1.3.6.1.4.1.4998.1.1.35.1.12.1.6
cadPolicyDistListOutAccessListName Name of the access list referred by distribute list. The access list name must be less than 32 characters	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.4998.1.1.35.1.12.1.7
cadPolicyDistListOutStatus The row status variable, used according to row installation and removal conventions. Once access list specified default row status is UP.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.12.1.8
cadPolicyDistListOutIfIndex Interface for which distribute list is applied. The value will be 1 if the distribute list is applied to all interfaces.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.35.1.12.1.9

Distribute List Out Table

cadDistListOutEntry row .1.3.6.1.4.1.4998.1.1.35.1.13.1

A row in Distribute List Out table

Indexes

cadDistListOutVrIndex cadDistListOutDestProtocol cadDistListOutSrcProtocol

Column	Syntax	OID
cadDistListOutVrIndex virtual router index	Integer32 Constraints: range: 1-99	.1.3.6.1.4.1.4998.1.1.35.1.13.1.1
cadDistListOutDestProtocol Destination protocol for which distribute list is applied.		.1.3.6.1.4.1.4998.1.1.35.1.13.1.2
cadDistListOutSrcProtocol Source protocol for which distribute list is applied.		.1.3.6.1.4.1.4998.1.1.35.1.13.1.3
cadDistListOutAccessListNum Access List Number	Integer32r/w Constraints: range: 0-999	.1.3.6.1.4.1.4998.1.1.35.1.13.1.4
cadDistListOutStatus The row status variable, used according to row installation and removal conventions. Once access list specified default row status is active.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.13.1.5
cadDistListOutAccessListName Access List Name	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.35.1.13.1.6

This table maps names to ACL entries.
Each row associates a name with the indexed ACL.

cadAclNameEntry row .1.3.6.1.4.1.4998.1.1.35.1.14.1

A conceptual row containing name information about an ACL.

Indexes

cadNameAclName cadNameAclNumber

Column	Syntax	OID
cadNameAclName The name of the access control list.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.4998.1.1.35.1.14.1.1
cadNameAclNumber Extended ACL number. Extended ACLs are in the range 100-199. Standard ACLs are in the range 1-99.	Integer32 Constraints: range: 1-399	.1.3.6.1.4.1.4998.1.1.35.1.14.1.2
cadNameAclStatus RowStatus used to add and remove names for ACLs. When an ACL is removed, the associated name is also removed.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.14.1.3

The cadPolicyAclExtTable augments the cadPolicyAclTable with
a count for total number of times the access list
entry has been matched by all referencing applications.

cadPolicyAclExtEntry row .1.3.6.1.4.1.4998.1.1.35.1.16.1

Information about the policy access list entry.

Indexes

No indexes recorded

Column	Syntax	OID
cadAclEntryCount Total number of times the access list entry has been matched by all referencing applications.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.16.1.1

This table maps policy route map names to route map entries.
Each row associates a name with the indexed policy route map.

cadRouteMapTagEntry row .1.3.6.1.4.1.4998.1.1.35.1.30.1.1

A conceptual row containing name information for a policy route map.

Indexes

cadRouteMapTagName

Column	Syntax	OID
cadRouteMapTagName Name to used for this policy route map	OctetString Constraints: range: 1-64	.1.3.6.1.4.1.4998.1.1.35.1.30.1.1.1
cadRouteMapTagId Id used to associate entries in the policy route map table to this name.	Integer32r/w Constraints: range: 1-64	.1.3.6.1.4.1.4998.1.1.35.1.30.1.1.2
cadRouteMapTagRowStatus The row status variable used according to row installation and removal convention. In our case, we have simplified this to the usage of only the following states - active, createAndGo, and destroy. Other three states no…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.30.1.1.3

This table contains policy route map data where each row
contains information about the ACL being used and what
set operations should be applied to the IP packet on a match.

cadRouteMapEntry row .1.3.6.1.4.1.4998.1.1.35.1.30.2.1

A conceptual row containing information for a policy route map entry.

Indexes

cadRouteMapId cadRouteMapSeqNum

Column	Syntax	OID
cadRouteMapId Id used to associate entries in the policy route map table.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.1
cadRouteMapSeqNum Sequence number used to order the match statements.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.2
cadRouteMapMatchType Type of match to used for this entry. Permit matches on the provided ACL and then applies the defined set operations before destination routing. Deny matches on the provided ACL and then directly routes to the destina…	Enumerationr/w Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.3
cadRouteMapMatchAcl ACL used to match the incoming packet. Since IPv4 is the only supported address type, the ACL number must be an extended or standard ACL. A value 0 implies that no ACL is used and all packets will match this entry.	Integer32r/w Constraints: range: 0-199	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.4
cadRouteMapSetIpPrec Indicates whether the IP Precedence should be changed on the packet if it matches the ACL and this is a permit type of match.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.5
cadRouteMapIpPrec The IP precedence value that should be used to replace the existing IP precedence of the matching packet.	Enumerationr/w Enumerated Values: 0 routine 1 priority 2 immediate 3 flash 4 flash-override 5 critical 6 internet 7 network	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.6
cadRouteMapSetIpTos Indicates whether the IP TOS should be changed on the packet if it matches the ACL and this is a permit type of match.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.7
cadRouteMapIpTos The IP TOS value that should be used to replace the existing IP TOS of the matching packet.	Enumerationr/w Enumerated Values: 0 normal 1 min-monetary-cost 2 max-reliability 4 max-throughput 8 min-delay	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.8
cadRouteMapSetNextHop Indicates whether the next hop setting should be used to specify the adjacent next hop router when forwarding the matching packet.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.9
cadRouteMapNextHopAddrType The address type of the next hop and backup next hop addresses. Currently IPv4 is the only supported address type.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.10
cadRouteMapNextHop The address of the adjacent next hop router to use in forwading the matching packet. The next hop router address must be the address of an ajacent router, and the routing table (VRF?) is used to verify that the addre…	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.11
cadRouteMapSetBackupNextHop Indicates whether the backup next hop setting should be used to specify the adjacent next hop router when forwarding the matching packet. This only would be done if the primary next hop was not set or was unreachable.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.12
cadRouteMapBackupNextHop The address type of a second next hop, that can be used only if the primary next hop address can not be reached. Only Ipv4 addresses are currently supported.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.13
cadRouteMapSetNullInterface If set to true and the packet matches the ACL, it will be dropped.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.14
cadRouteMapRowStatus The row status variable used according to row installation and removal convention. In our case, we have simplified this to the usage of only the following states - active, createAndGo, and destroy. Other three states no…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.15
cadRouteMapSetIpDscp Indicates whether the IP DSCP should be changed on the packet if it matches the ACL and this is a permit type of match.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.16
cadRouteMapIpDscp The IP DSCP value that should be used to replace the existing IP DSCP of the matching packet.	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.17
cadRouteMapSetRecursiveNextHop Indicates whether the recursive next hop setting should be used to specify the next hop for the remote router when forwarding the matching packet.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.18
cadRouteMapRecursiveNextHop The address type of a remote router next hop, that is used to perform a recursive route lookup. Only Ipv4 addresses are currently supported.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.19

This table contains policy route map counts where each row
contains information about the number of packets that match
the specified ACL and were successfully changed with the defined
set operations, as well as those that matched the ACL but failed
the set operations.

cadRouteMapStatsEntry row .1.3.6.1.4.1.4998.1.1.35.1.30.3.1

A conceptual row containing counts information for a policy route map entry.

Indexes

cadRouteMapId cadRouteMapSeqNum

Column	Syntax	OID
cadRouteMapPktMatched The number of packets that match the ACL defined in the route map entry and where the action was also successful. For matches of type deny, the packet is routed by destination, and for packets of type match, the packet…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.35.1.30.3.1.1
cadRouteMapByteMatched The number of bytes that match the ACL defined in the route map entry and where the action was also successful. For matches of type deny, the packet is routed by destination, and for packets of type match, the packet i…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.30.3.1.2
cadRouteMapPktFailed The number of packets that match the ACL defined in the route map entry and where the action failed. For route map entries of type match, the set operation failed.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.35.1.30.3.1.3
cadRouteMapByteFailed The number of packets that match the ACL defined in the route map entry and where the action failed. For route map entries of type match, the set operation failed.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.35.1.30.3.1.4