BINTEC-IPEXT-MIB Table View

The ipExtIfTable contains extended information related to
IP and the interfaces found on the system. Entries can only
be added or deleted by the system.

ipExtIfEntry row .0.3.1

Indexes

ipExtIfIndex

Column	Syntax	OID
ipExtIfIndex Unique interface index	Integer32 Type Constraints: range: -2147483648..2147483647	.0.3.1.1
ipExtIfRipSend specifies which versions of RIP messages are sent to that interface. Usually RIP messages are sent as broadcast, except this object is set to ripV2mcast. In this case RIP V2 messages are sent to the multicast address 22…	Enumerationr/w	.0.3.1.3
ipExtIfRipReceive specifies which versions of RIP messages are accepted from that interface. RIP V2 messages are received regardless if they are sent as broadcast or multicast.	Enumerationr/w	.0.3.1.4
ipExtIfProxyArp Switch for Proxy ARP on this interface.	Enumerationr/w	.0.3.1.5
ipExtIfNat This object can be used to switch NAT on and off for a specific interface.	Enumerationr/w	.0.3.1.6
ipExtIfNatRmvFin This object specifies, whether entries in the IpNatTable shall be removed, when TCP-FINS have been received and acknowledged in both directions, a TCP-RST has been received or a ICMP-ERROR message has been received for …	Enumerationr/w Enumerated Values: 1 forwardNoFrames 2 forwardAllFramesAsTagged 3 forwardAllFramesAsUntagged	.0.3.1.7
ipExtIfNatTcpTimeout TCP NAT entries vanish unconditionally after not being used for the amount of time specified by this object in seconds.	secondsInteger32r/w Constraints: range: 0-5184000	.0.3.1.8
ipExtIfNatOtherTimeout Non-TCP NAT entries vanish unconditionally after not being used for the amount of time specified by this object in seconds.	secondsInteger32r/w Constraints: range: 0-5184000	.0.3.1.9
ipExtIfNatOutXlat This object can be used to switch the outgoing address translation off. Then, all addresses are passed instead of being translated. The session mechanism remains active and implements a security mechanism.	Enumerationr/w	.0.3.1.10
ipExtIfAccounting Switch for accounting on the specified interface. An IP packet is being accounted, when this object is set to on for either the source or the destination interface.	Enumerationr/w	.0.3.1.11
ipExtIfTcpSpoofing Switch for TCP spoofing on this interface. TCP keepalive polls are answered by the BRICK to prevent unnecessary ISDN connections. Set this object to on for ISDN dialup interfaces.	Enumerationr/w	.0.3.1.12
ipExtIfAccessAction This object describes the action, that is done, when a packet received from the interface has been filtered out. When set to ignore, no action takes place. When set to refuse, an ICMP unreachable message is being sent t…	Enumerationr/w	.0.3.1.13
ipExtIfAccessReport This object specifies, how a packed filtered by accesslists should be logged. When set to none, no logging takes place. When set to info, protocol, ip-addresses and portnumbers are logged. When set to dump, a dump of th…	Enumerationr/w	.0.3.1.14
ipExtIfOspf Configure the OSPF status of this interface. Routing information about routes on passive and active interfaces is propagated on active interfaces. Only active interfaces run the OSPF protocol. When set to off the inte…	Enumerationr/w	.0.3.1.15
ipExtIfOspfMetric Configure the metric calculation of OSPF interfaces. If set to auto the metric is calculated based on ifSpeed. If set to fixed the metric is taken from the ospfIfMetricTable. Additionaly the metric adjustment for dialup…	Enumerationr/w	.0.3.1.16
ipExtIfTcpCksum Enable or disable the TCP checksum check for local packets received on the corresponding interface. Disabling the check may improve performance for some local applications (i.e. remote CAPI). This object should only be …	Enumerationr/w	.0.3.1.17
ipExtIfBackRtVerify This object activates an additional check for incoming packets. If set to on, incoming packets are only accepted if return packets sent back to their source IP address would be sent over the same interface. This preven…	Enumerationr/w	.0.3.1.18
ipExtIfRuleIndex This object defines the index of the first access rule that is applied for incoming packets. If set to 0 or if there is no access rule with this index no access rules are applied for this interface.	Integer32r/w Enumerated Values: 1 other 2 static 3 gvrp 4 ctDynamicEgress 5 etsysPolicyProfile 6 ctPortDefFwdMode 7 rfc3580VlanTunnelAttribute 8 mvrp Type Constraints: range: -2147483648..2147483647	.0.3.1.19
ipExtIfAuthentication This object defines the authentication scheme used for incoming packets.	Enumerationr/w Enumerated Values: 1 tagged 2 untagged 3 forbidden	.0.3.1.20
ipExtIfAuthMode This object defines the authentication mode. If set to strict each source IP address must be authenticated. If set to loose all source IP addresses are allowed if at least one IP address is successfully authenticated.	Enumerationr/w	.0.3.1.21
ipExtIfAuthLifeTime This object defines the time in seconds a successful authentication is valid since the IP partner was authenticated.	secondsInteger32r/w Constraints: range: 180-36000	.0.3.1.22
ipExtIfAuthKeepalive This object defines the period between short authentications that are invisible to the user	secondsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.3.1.23
ipExtIfRouteAnnounce This object defines the condition when routes on this interface are propagated by routing protocols. If set to up-only routes are only propagated if the operational status of the interface is up. If set to up-dormant ro…	Enumerationr/w	.0.3.1.24
ipExtIfIpFragmentation This object defines different modes used for fragmentation of IP datagrams greater than the MTU of the destination interface. If set to enabled (1) each IP datagram will be splitted into a first fragment MTU sized and t…	Enumerationr/w	.0.3.1.25
ipExtIfRerouting This object enables or disables rerouting on this interface. The default value is enabled. If set to disabled, then only the better one route from two or more possible routes is chosen, even if the ifOperStatus of the…	Enumerationr/w	.0.3.1.26
ipExtIfBodRuleIndex This object defines the index of the first rule used for Bandwidth on Demand (BOD) that is applied for incoming and/or outgoing traffic. If set to 0 or if there is no entry in the ipBodRuleTable with this index no BOD-s…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.3.1.27
ipExtIfQosRuleIndex This object defines the index of the first rule used for Qos (Qualtiy of Service) rules applied for IP traffic. If set to 0 or if there is no entry in the ipQoSTable with this index no QoS-specific information is applie…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.3.1.28
ipExtIfIpsecAccounting This object determines, whether packets which are en- or decapsulated by IPSec should be accounted with encapsulation header(ipsec) or without the encapsulation header (clear), or even twice (both).	Enumerationr/w	.0.3.1.29
ipExtIfMulticast Enable that multicast frames are accepted from that interface.	Enumerationr/w Enumerated Values: 1 tagged 2 untagged 3 forbidden	.0.3.1.30
ipExtIfNatSilentDeny This object specifies - if NAT is enabled (see ipExtIfNat) - whether incoming IP packets not passed by the NAT barrier should answered with an ICMP Host Unreachable or TCP RST message addressed to to packet originator. …	Enumerationr/w	.0.3.1.31
ipExtIfNatPPTPXlat This object specifies - if NAT is enabled (see ipExtIfNat) - whether PPTP (point to point protocol) connections are translated. This is needed if there are more than one PPTP client behind NAT.	Enumerationr/w	.0.3.1.33
ipExtIfTcpMssClamping This object specifies whether TCP MSS clamping is enabled on the interface. -1 disables clamping, 0 clamps the MSS depending on the interface MTU. A value > 0 will be used as clamping size.	bytesInteger32r/w Constraints: range: -1-32000	.0.3.1.34
ipExtIfNbdgmRelayAddress This object contains the destination IP address to which Netbios Datagram request are forwarded by the router.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.3.1.35
ipExtIfNatMaxSessions This object limits the maximum number of NAT sessions on a interface.	Integer32r/w Constraints: range: 1-65535	.0.3.1.36
ipExtIfAllowedPeers If this object is set to 'dhcpclients', the router refuses to exchange data with hosts which are not DHCP clients on this interface. If this object is set to 'all', the router accepts to exchange data with any host.	Enumerationr/w	.0.3.1.37
ipExtIfNatFlush If this object in enabled NAT-Flushing is done else not. NAT-Flushing means that the NAT Entries for this interface will be deleted in the case of an OperStatus change to down or dormant.	Enumerationr/w	.0.3.1.38
ipExtIfHttpRedirect If not set to 'disabled' all HTTP requests on this interface will be directed either to the local HTTP daemon or HTTP proxy.	Enumerationr/w	.0.3.1.39
ipExtIfWolRuleIndex This object defines the index of the first rule used for Wake-On-LAN (WOL) that is applied for incoming and/or outgoing traffic. If set to 0 or if there is no entry in the ipWolRuleTable with this index no WOL-specific …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.3.1.40

The ipExtRtTable can be used in addition (not instead of)
to the ipRouteTable to specify routing of IP datagrams. 
The selection of datagram-types is more specific with
the ipExtRtTable, so routing of different services over
different pathes is possible. The specification of local 
IP-addresses is not possible in the ipExtRtTable.
          
The ipExtRtTable will be searched before the ipRouteTable.
If a matching entry is found, it will be taken for routing
and no further lookup in the ipRouteTable will happen.

ipExtRtEntry row .0.4.1

Each entry in the ipExtRtTable describes a set of IP
datagrams and the destination interface for that set.
Metric parameters allow for ordering of the different
specifications for overlapping sets.

Indexes

ipExtRtProtocol

Column	Syntax	OID
ipExtRtProtocol This object specifies the value of the protocolfield in the ip header for all IP-datagrams belonging to the set. If this object is set to dont-verify, the value of the protocol field is not specified and can take any va…	Enumerationr/w	.0.4.1.1
ipExtRtSrcIfIndex This object specifies the source index of the IP-datagrams. If this object has a value other than 0, only datagrams received over the interface with the appropriate interface index are considered to be part of the set.…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.2
ipExtRtSrcAddr This object describes together with ipExtRtSrcMask the range of the source-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0.0 the source- addresses for the datagrams in the set is no…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.4.1.3
ipExtRtSrcMask This object describes together with ipExtRtSrcAddr the range of the source-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0.0 the source- addresses for the datagrams in the set is no…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.4.1.4
ipExtRtSrcPort This object describes together with ipExtRtSrcPortRange the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and including the two objects are within the range. …	Integer32r/w Constraints: range: -1-65535	.0.4.1.5
ipExtRtSrcPortRange This object describes together with ipExtRtSrcPort the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and including the two objects are within the range. If …	Integer32r/w Constraints: range: -1-65535	.0.4.1.6
ipExtRtDstAddr This object describes together with ipExtRtDstMask the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0.0 the target- addresses for the datagrams in the set is no…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.4.1.7
ipExtRtDstMask This object describes together with ipExtRtDstAddr the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0.0 the target- addresses for the datagrams in the set is no…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.4.1.8
ipExtRtDstPort This object describes together with ipExtRtDstPortRange the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and including the two objects are within the range. …	Integer32r/w Constraints: range: -1-65535	.0.4.1.9
ipExtRtDstPortRange This object describes together with ipExtRtDstPort the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and including the two objects are within the range. If …	Integer32r/w Constraints: range: -1-65535	.0.4.1.10
ipExtRtTos This object describes together with ipExtRtTosMask the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TOS value is considered within the range, when the following …	Integer32r/w Constraints: range: 0-255	.0.4.1.11
ipExtRtTosMask This object describes together with ipExtRtTos the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TOS value is considered within the range, when the following equa…	Integer32r/w Constraints: range: 0-255	.0.4.1.12
ipExtRtDstIfMode This object describes different behavior depending on the ifOperStatus of the destination interface: dialup-wait: The route matches, when the ifOperStatus of the destination interface is either up or do…	Enumerationr/w	.0.4.1.13
ipExtRtDstIfIndex This object specifies the destination interface for the IP-datagrams belonging to the set. If the value of this object is set to 0, the datagrams of the set are discarded and an ICMP destination unreachable datagram is …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.14
ipExtRtNextHop This object is used on point-to-multipoint interfaces with indirect routes (see ipExrRtType) to specify the IP-address of the gateway on the network, where the datagram should be routed to.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.4.1.15
ipExtRtType This object specifies, on point-to-multipoint interface whether the datagram shall be sent to the destination IP address in the IP datagram header (direct) or to a gateway (indirect). In the later case, the IP-addres of…	Enumerationr/w	.0.4.1.16
ipExtRtMetric1 This object is used to specify an order on the entries in the ipExtRtTable. If a datagram is matching multiple entries, the entry with the lowest value of ipExtRtMetric1 is choosen. The decision is undefined, when even …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.17
ipExtRtMetric2 Undefined yet; for further extension	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.18
ipExtRtMetric3 Undefined yet; for further extension	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.19
ipExtRtMetric4 Undefined yet; for further extension	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.20
ipExtRtMetric5 Undefined yet; for further extension	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.21
ipExtRtProto This object describes, how the route has been gained. This will normaly be netmgmt, because there is currently no routing protocol, that is able to handle extended routes.	Enumerationr/w	.0.4.1.22
ipExtRtAge This object specifies the age of the route.	RFC1155-SMITimeTicksr/w Type Constraints: range: 0..4294967295	.0.4.1.23
ipExtRtDescription A textual string describing this extended route.	OctetStringr/w Constraints: range: 0-255	.0.4.1.24

If NAT is switched on for an interface, this table contains
an entry for each session running over the interface. Table
entries are creates by the system whenever a valid session
is established. A session may be either a tcp connection,
a udp connection or an icmp connection with icmp-echo messages
(ping). A valid session is either an outgoing session or
an incoming session specified in the ipNatPresetTable.
          
Everything behind an interface with NAT enabled is called
outside. The BRICK itself and all networks connected
to it via interfaces without NAT are called inside.
          
Table entries are removed after timeout. This timeout
is
	specified by ipExtIfNatOtherTimeout for UDP
	and ICMP sessions.
          
	specified by ipExtIfTcpTimeout for TCP sessions
          
	16 seconds for closed TCP-sessions (FIN has been
	received and acknowledged in both directions).

ipNatEntry row .0.5.1

Indexes

ipNatIfIndex ipNatProtocol ipNatIntAddr ipNatIntPort

Column	Syntax	OID
ipNatIfIndex This object specifies the interface, for which the session is monitored.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.5.1.1
ipNatProtocol This object specifies the protocol, the session is using. The value icmp specifies an icmp-echo (ping) session. ICMP error messages are processed by the appropriate tcp or udp session.	Enumeration	.0.5.1.2
ipNatIntAddr This object specifies the internal local IP Address used for the session. The internal address is only visible to inside networks and is translated to the external address, when a packet is being sent outside.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.5.1.3
ipNatIntPort This object specifies the internal local portnumber used for the session. The internal portnumber is only visible to inside networks and is translated to the external portnumber whenever a packet is being sent outside.	Integer32 Constraints: range: 0-65535	.0.5.1.4
ipNatExtAddr This object specifies the external local address used for the session. This address is visible outside only and will be translated to the internal address, whenever a packet is received from outside.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.5.1.5
ipNatExtPort This object specifies the external local portnumber used for the session. This address is visible outside only and is translated to the internal portnumber, whenever a packet is received from outside.	Integer32 Constraints: range: 0-65535	.0.5.1.6
ipNatRemoteAddr This object specifies the remote IP-address used for the session. This is an outside address. However, it is visible to outside networks and also to inside networks.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.5.1.7
ipNatRemotePort This object specifies the remote portnumber used for the session. This is an outside portnumber. However, it is visible to outside networks and also to inside networks.	Integer32 Constraints: range: 0-65535	.0.5.1.8
ipNatDirection This object specifies, whether the session is incoming (from outside to inside) or outgoing (from inside to outside).	Enumeration	.0.5.1.9
ipNatAge This object specifies how long no packet has been transferred for the session and is used internally for timeout purposes.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.0.5.1.10
ipNatContext This object holds a protocol specific context needed to identify sessions for ICMP unreachable address mapping.	Integer32 Constraints: range: 0-4294967295	.0.5.1.11
ipNatTimeout When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds.	secondsInteger32 Constraints: range: 1-5184000	.0.5.1.12
ipNatState Set this object to delete to remove this entry.	Enumeration	.0.5.1.13
ipNatCategory Specifies the NAT category according RFC 3489 and 5389 to be applied for UDP traffic matching with this entry.	Enumeration	.0.5.1.14

This table specifies the IP addresses and port numbers
for sessions requested from outside. If this table is
empty and NAT is enabled, only packets for sessions
initiated from inside are forwarded.
          
The IP address and the port number of the internal server
can be specified individually for each combination of
          
	- protocol (udp/tcp/icmp)
	- initiating hosts IP address (RemoteAddr, RemoteMask)
	- destination address or network (ExtAddr, ExtMask)
	- destination port number or range (ExtPort, ExtPortRange)
          
Entries in the table are created and removed manually
by network management.

ipNatPresetEntry row .0.6.1

Indexes

ipNatPrIfIndex ipNatPrProtocol ipNatPrExtPort

Column	Syntax	OID
ipNatPrIfIndex This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use NAT.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.6.1.1
ipNatPrProtocol This object specifies the protocol, for which the table entry shall be valid.	Enumerationr/w	.0.6.1.2
ipNatPrRemoteAddr This object specifies together with ipNatPrRemoteMask the the set of IP addresses of remote hosts initiating a session. The table entry will be valid for an incoming packet, when the IP adress of the remote host initiat…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.6.1.3
ipNatPrRemoteMask This object specifies together with ipNatPrRemoteAddr the set of IP addresses of remote hosts initiating the session. The table entry will be valid for an incoming packet, when the IP adress of the remote host initiatin…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.6.1.4
ipNatPrExtAddr This object specifies together with ipNatPrExtMask the set of destination IP addresses, for which the table entry shall be valid. The entry is valid, if the target IP address of an incoming IP packet lies in the range s…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.6.1.5
ipNatPrExtMask This object specifies together with ipNatPrExtAddr the set of destination IP addresses, for which the table entry shall be valid. The entry is valid, if the target IP address of an incoming packet lies in the range spec…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.6.1.6
ipNatPrExtPort This object specifies together with ipNatPrExtPortRange the range of port numbers for incoming packets, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all portnumbers. If…	Integer32r/w Constraints: range: -1-65535	.0.6.1.7
ipNatPrExtPortRange This object specifies together with ipNatPrExtPort the range of portnumbers for incoming packets, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all portnumbers. If ipNat…	Integer32r/w Constraints: range: -1-65535	.0.6.1.8
ipNatPrIntAddr With ipNatPrIntMask, this object specifies the internal target host's IP address for incoming packets matching the table entry. An incoming packet matching this entry will be routed to the internal server…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.6.1.9
ipNatPrIntPort This object specifies the internal target host's port-number for incoming packets matching the table entry. If this object is set to -1, the target portnumber will be taken from the original incoming packet. No translat…	Integer32r/w Constraints: range: -1-65535	.0.6.1.10
ipNatPrIntMask With ipNatPrIntAddr, this object specifies the internal target host's IP address for incoming packets matching the table entry. An incoming packet matching this entry will be routed to the internal server…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.6.1.11
ipNatPrTimeout When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. If set to the default value of 0, the timeout will be set …	secondsInteger32r/w Constraints: range: 0-5184000	.0.6.1.12
ipNatPrDescr A textual string describing this NAT forwarding rule.	OctetStringr/w Constraints: range: 0-255	.0.6.1.13

.

ipSessionEntry row .0.7.1

Indexes

ipSessionProtocol ipSessionSrcAddr ipSessionSrcPort ipSessionDstAddr ipSessionDstPort

Column	Syntax	OID
ipSessionSrcAddr source address of IP session	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.7.1.1
ipSessionSrcPort source port of IP session	Integer32 Constraints: range: 0-65535	.0.7.1.2
ipSessionDstAddr destination port of IP session	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.7.1.3
ipSessionDstPort destination port of IP session	Integer32 Constraints: range: 0-65535	.0.7.1.4
ipSessionOutPkts outgoing packets in IP session	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.7.1.5
ipSessionOutOctets outgoing octets in IP session	bytesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.7.1.6
ipSessionInPkts incoming packets in IP session	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.7.1.7
ipSessionInOctets incoming octets in IP session	bytesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.7.1.8
ipSessionProtocol protocol of IP session	Enumeration	.0.7.1.9
ipSessionAge age of IP session	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.0.7.1.10
ipSessionIdle idle time of IP session	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.0.7.1.11
ipSessionSrcIfIndex source interface index of IP session	Integer32 Type Constraints: range: -2147483648..2147483647	.0.7.1.12
ipSessionDstIfIndex destination interface index of IP session	Integer32 Type Constraints: range: -2147483648..2147483647	.0.7.1.13

This table specifies how routes from one routing protocol
are imported into another routing protocol. The dummy
protocol default-route allows the generation of a default
route for the routing domain. Not all combinations of 
source and destination protocols might be valid or 
implemented.

ipImportEntry row .0.12.1

Indexes

ipImportSrcProto ipImportDstProto ipImportAddr

Column	Syntax	OID
ipImportSrcProto This object describes the protocol that generated the route and inserted it into the routing table.	Enumerationr/w	.0.12.1.1
ipImportDstProto This object describes the destination protocol into that the routes should be imported.	Enumerationr/w	.0.12.1.2
ipImportMetric1 This object defines the metric in the context of the destination protocol the imported routes should get. If set to -1 these routes get a protocol specific default metric.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.12.1.3
ipImportType This object might define protocol specific properties of the imported routes in the context of the destination protocol.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.12.1.4
ipImportAddr This object specifies together with ipImportMask the range of IP addresses for which the table entry should be valid. The entry is valid if the destination IP address of the route lies in the range specified by both obj…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.12.1.5
ipImportMask This object specifies together with ipImportAddr the range of IP addresses for which the table entry should be valid. The entry is valid if the destination IP address of the route lies in the range specified by both obj…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.12.1.6
ipImportEffect This object defines the effect this row should have. If set to import, the importation from ipImportSrcProto to ipImportDstProto takes place. If set to doNotImport the importation is prevented.	Enumerationr/w	.0.12.1.7
ipImportIfIndex This object specifies the interface index of the interface for which the entry should be valid. If set to -1 it will be valid for all interfaces.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.12.1.8
ipImportAssociatedAS This object specifies an optional Autonomous System identifier for use with BGP.	Integer32r/w Constraints: range: 0-65535	.0.12.1.9
ipImportRouteMapName This object specifies an optional route-map name for use with BGP.	OctetStringr/w Constraints: range: 0-255	.0.12.1.10

This table defines the order, in which routes from different
protocols are being used to determine the destination of an
ip packet. The table will contain an entry for each type
of routing protocol including STATIC and DIRECT routes.
A priority-value can be configured for each of those protocols
to get an order between the different protocols. The table
contains a fixed number of entries. Only the priority may be
configured.

ipPriorityEntry row .0.13.1

Indexes

ipPriorityProto

Column	Syntax	OID
ipPriorityProto This object specifies the routig-protocol, for which the entry is valid.	Enumeration	.0.13.1.1
ipPriorityValue This object contains the priority-value for a specific routing protocol. Low values mean high precedence.	Integer32r/w Constraints: range: 0-63	.0.13.1.2

The ipFilterTable defines filters that describe subsets
of IP packets. The filter matches if all conditions defined
are true when comparing with the header of an IP packet.

ipFilterEntry row .0.15.1

Indexes

ipFilterProtocol

Column	Syntax	OID
ipFilterIndex This object uniquely references this filter. The index value is generated automatically.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.15.1.1
ipFilterDescr A textual string describing this filter.	OctetStringr/w Constraints: range: 0-255	.0.15.1.2
ipFilterProtocol This object specifies the value of the protocol field in the ip header for all IP-datagrams belonging to the set. If this object is set to dont-verify, the value of the protocol field is not specified and can take any v…	Enumerationr/w	.0.15.1.3
ipFilterSrcAddr This object specifies together with ipFilterSrcMask the set of IP addresses of datagrams that belong to the subset defined by this entry. If both objects are set to 0.0.0.0 the source-addresses for the datagrams in the…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.15.1.4
ipFilterSrcMask This object specifies together with ipFilterSrcAddr the set of IP addresses of datagrams that belong to the subset defined by this entry. If both objects are set to 0.0.0.0 the source-addresses for the datagrams in the…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.15.1.5
ipFilterSrcPort This object describes together with ipFilterSrcPortRange the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and including the two objects are within the range. …	Integer32r/w Constraints: range: -1-65535	.0.15.1.6
ipFilterSrcPortRange This object describes together with ipFilterDstPort the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and including the two objects are within the range. If…	Integer32r/w Constraints: range: -1-65535	.0.15.1.7
ipFilterDstAddr This object describes together with ipFilterDstMask the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0.0 the target- addresses for the datagrams in the set is n…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.15.1.8
ipFilterDstMask This object describes together with ipFilterDstAddr the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0.0 the target- addresses for the datagrams in the set is n…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.15.1.9
ipFilterDstPort This object describes together with ipFilterDstPortRange the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and including the two objects are within the range. …	Integer32r/w Constraints: range: -1-65535	.0.15.1.10
ipFilterDstPortRange This object describes together with ipFilterDstPort the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and including the two objects are within the range. If…	Integer32r/w Constraints: range: -1-65535	.0.15.1.11
ipFilterTcpConnState This object describes the state of the TCP connection associated with the packets belonging to the set. If this object is set to established, the value of the TCP flags of incoming packets is checked. Packets with fl…	Enumerationr/w	.0.15.1.12
ipFilterIcmpType This object describes the ICMP type of the packets belonging to the set. If this object is set to dont-verify, the value of the ICMP type field is not specified and can take any value.	Enumerationr/w	.0.15.1.13
ipFilterTos This object describes together with ipFilterTosMask the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TOS value is considered within the range, when the following…	Integer32r/w Constraints: range: 0-255	.0.15.1.14
ipFilterTosMask This object describes together with ipFilterTos the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TOS value is considered within the range, when the following equ…	Integer32r/w Constraints: range: 0-255	.0.15.1.15
ipFilterLevel2Prio This object describes together with ipFilterLevel2PrioMask the range of the level 2 priority field associated with the IP-datagrams belonging to the set. A priority value is considered within the range, when the follow…	Integer32r/w Constraints: range: 0-7	.0.15.1.16
ipFilterLevel2PrioMask This object describes together with ipFilterLevel2PrioMask the range of the level 2 priority field associated with the IP-datagrams belonging to the set. A priority value is considered within the range, when the follow…	Integer32r/w Constraints: range: 0-7	.0.15.1.17
ipFilterSrcIfIndex This object specifies the source index of the IP-datagrams. If this object has a value other than 0, only datagrams received over the interface with the appropriate interface index are considered to be part of the set.…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.15.1.18

The ipRuleTable defines access rules for checking incoming
IP packets. The rules are processed in order, i.e. each rule
has a link to the next rule. The set of rules is processed
until a match occurs, that means the rule's associated filter 
matches and the specified action is performed (either accept
or deny a packet). The last rule is implicitly a deny rule.
The set of rules to be processed can be defined for each
interface

ipRuleEntry row .0.16.1

Indexes

ipRuleFilterIndex

Column	Syntax	OID
ipRuleIndex Unique rule index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.16.1.1
ipRuleFilterIndex References the rule's associated filter.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.16.1.2
ipRuleAction This object specifies the action to be performed if the rule's associated filter matches. If set to ignore the filter is not consulted and the next rule is processed immediately.	Enumerationr/w	.0.16.1.3
ipRuleNextRuleIndex Specifies the next rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.16.1.4
ipRuleDescr A textual string describing this access rule.	OctetStringr/w Constraints: range: 0-255	.0.16.1.5

This table specifies the IP address translation for
outgoing sessions. If no matching entry is found the
IP address is set to the IP address defined on the
interface configured for NAT. If a matching entry is
found, the source IP address of outgoing IP packets
is translated according to the couple 'ipNatOutExtAddr /
ipNatOutExtMask'.
          
	- If external IP address is a 'host IP address', the
	  whole source IP address is mapped.
	- If external IP address is a 'net IP address', only
	  the 'net part' of source IP address is affected.
	  This table is only used if the outgoing address 
translation is activated (ipExtIfNatOutXlat).
          
Entries in the table are created and removed manually
by network management.

ipNatOutEntry row .0.18.1

Indexes

ipNatOutIfIndex ipNatOutIntAddr ipNatOutExtAddr

Column	Syntax	OID
ipNatOutIfIndex This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use NAT.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.18.1.1
ipNatOutProtocol This object specifies the protocol, for which the table entry shall be valid.	Enumerationr/w	.0.18.1.2
ipNatOutRemoteAddr This object specifies together with ipNatOutRemoteMask the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.0, the table entry will be valid for any target IP address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.18.1.3
ipNatOutRemoteMask This object specifies together with ipNatOutRemoteAddr the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.0, the table entry will be valid for any target IP address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.18.1.4
ipNatOutExtAddr With ipNatOutExtMask, this object specifies the external 'IP address' or 'NET address' to which the internal IP address is mapped. - To map exactly to ipNatOutExtAddr (i.e. map to a single IP address),…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.18.1.5
ipNatOutRemotePort This object specifies together with ipNatOutRemotePortRange the range of portnumbers for outgoing packets, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all portnumbers.…	Integer32r/w Constraints: range: -1-65535	.0.18.1.6
ipNatOutRemotePortRange This object specifies together with ipNatOutRemotePort the range of portnumbers for outgoing packets, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all portnumbers. If i…	Integer32r/w Constraints: range: -1-65535	.0.18.1.7
ipNatOutIntAddr This object specifies together with ipNatOutIntMask the internal hosts IP address for outgoing packets matching the table entry. If both objects are set to 0.0.0.0, the table entry will be valid for any source IP …	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.18.1.8
ipNatOutIntMask This object specifies together with ipNatOutIntAddr the internal hosts IP address for outgoing packets matching the table entry. If both objects are set to 0.0.0.0, the table entry will be valid for any source IP …	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.18.1.9
ipNatOutIntPort This object specifies the internal source port for which the table entry shall be valid. If this object is set to -1, any internal source port matches this entry.	Integer32r/w Constraints: range: -1-65535	.0.18.1.10
ipNatOutExtPort This object may be used to specify a fixed external source port to which the internal source port is mapped. If this object is set to -1, the port is mapped to the next free source port available.	Integer32r/w Constraints: range: -1-65535	.0.18.1.11
ipNatOutExtMask With ipNatOutExtAddr, this object specifies the external 'IP address' or 'NET address' to which the internal IP address is mapped. - To map exactly to ipNatOutExtAddr (i.e. map to a single IP address),…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.18.1.12
ipNatOutTimeout When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. If set to the default value of 0, the timeout will be set …	secondsInteger32r/w Constraints: range: 0-5184000	.0.18.1.13
ipNatOutDescr A textual string describing this NAT translation rule.	OctetStringr/w Constraints: range: 0-255	.0.18.1.14
ipNatOutNatCategory Specifies the NAT category according RFC 3489 and 5389 to be applied for UDP traffic matching with this entry.	Enumerationr/w	.0.18.1.15
ipNatOutIntPortRange This object specifies together with ipNatOutIntPort the internal source port range for which the table entry shall be valid. If this object is set to -1, only ipNatOutIntPort is used as selector for this entry.	Integer32r/w Constraints: range: -1-65535	.0.18.1.16
ipNatOutExtPortRange This object may be used together with ipNatOutExtPort to specify a fixed external source port number range to which the internal source port numbers are mapped. This mapping depends on the position of the original sourc…	Integer32r/w Constraints: range: -1-65535	.0.18.1.17

This table specifies the watched IP addresses.
          
Entries in the table are created and removed manually
by network management.

ipHostsAliveEntry row .0.19.1

Indexes

ipHostsAliveIPAddress

Column	Syntax	OID
ipHostsAliveGroup The group of the watched IP-Addresses	Integer32r/w Constraints: range: 0-255	.0.19.1.1
ipHostsAliveIPAddress The watched IP-Address. If set to zero, the default gateway is used.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.19.1.2
ipHostsAliveState The State of the watched IP-Address	Enumeration	.0.19.1.3
ipHostsAliveInterval This is the time interval for state verification	secondsInteger32r/w Constraints: range: 1-65536	.0.19.1.4
ipHostsAliveDownAction Action be performed if the ipHostsAliveState changes to down (2), If set to none (4) there is no action specified, if set to monitor (7) this entry just enables monitoring of this status in other subsystem context like …	Enumerationr/w	.0.19.1.5
ipHostsAliveFirstIfIndex The first ifc	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.19.1.6
ipHostsAliveRange The range of all ifc's	Integer32r/w Constraints: range: 0-65536	.0.19.1.7
ipHostsAliveSrcIPAddress The source IP-Address	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.19.1.8
ipHostsAliveTrials How many ping attempts until host is considered down. Default value is 3.	Integer32r/w Constraints: range: 1-65535	.0.19.1.9
ipHostsAliveBackups How many successful pings until host is considered up. Default value is 1.	Integer32r/w Constraints: range: 1-65535	.0.19.1.10

The ipBodRuleTable defines access rules for checking incoming
IP packets. The rules are processed in order, i.e. each rule
has a link to the next rule. The set of rules is processed
until a match occurs, that means the rule's associated filter 
matches and the specified action is performed (either request
or deny additional bandwidth). The last rule is implicitly a
deny rule. The set of rules to be processed can be defined
for each interface.

ipBodRuleEntry row .0.21.1

Indexes

ipBodRuleFilterIndex

Column	Syntax	OID
ipBodRuleIndex Unique rule index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.21.1.1
ipBodRuleFilterIndex References the rule's associated filter.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.21.1.2
ipBodRuleAction This object specifies the action to be performed if the rule's associated filter matches. If set to ignore the filter is not consulted and the next rule is processed immediately.	Enumerationr/w	.0.21.1.3
ipBodRuleDirection This object specifies the direction of the packets for which the rule is processed.	Enumerationr/w	.0.21.1.4
ipBodRuleChannels The number of B-channels to invoke if the rule's associated filter matches.	Integer32r/w Constraints: range: 0-8	.0.21.1.5
ipBodRuleNextRuleIndex Specifies the next rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.21.1.6
ipBodRuleIdleTime Specifies the time in seconds the interface-specific shorthold interval (see biboPPPTable) is extended if the rule's associated filter matches. When set to zero this setting is ignored. When set to -1 matching packets a…	secondsInteger32r/w Constraints: range: -1-3600	.0.21.1.7

The ipQosTable defines the classifier rules that are applied
to IP traffic arriving this interface in a particular
direction. The rules are processed in order, i.e. each rule
has a link to the next rule. The set of rules is processed
until a match occurs, that means the rule's associated filter
matches and the specified action is performed (alter the IP
headers TOS field, alter associated level 2 priority, specify 
a service class for QoS). The set of these rules to be 
processed can be defined for each interface.

ipQoSEntry row .0.22.1

Indexes

ipQoSFilterIndex

Column	Syntax	OID
ipQoSIndex Unique rule index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.22.1.1
ipQoSFilterIndex References the associated filter (see IpFilterTable).	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.22.1.2
ipQoSNextRuleIndex Specifies the next classifier rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.22.1.3
ipQoSActionobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: This object specifies the action to be performed if …	Enumerationr/w	.0.22.1.4
ipQoSTosobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Value for TOS field inside IP header to be set.	Integer32r/w Constraints: range: 0-255	.0.22.1.5
ipQoSTosSetRateobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Maximum amount of packets per second that should be …	Integer32r/w Constraints: range: 0-65535	.0.22.1.7
ipQoSTosSetBurstobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Maximum amount of packets per second additional to t…	Integer32r/w Constraints: range: 0-65535	.0.22.1.8
ipQoSTosSetExceedActionobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: This object specifies how to mark packets in excess …	Enumerationr/w	.0.22.1.9
ipQoSTosRemarkobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Value for TOS field inside IP header to be set when…	Integer32r/w Constraints: range: 0-255	.0.22.1.10
ipQoSServiceClass This object specifies together with ipQoSClassId the class of service used for the congestion management, priorization and traffic shapping. If set to high-priority(2) (high priority service class) the related traffic w…	Enumerationr/w	.0.22.1.11
ipQoSClassId This object specifies together with ipQoSServiceClass (normal(1) only) the class of service used for congestion avoidance, congestion management, priorization and traffic shapping. Note that this ID is not used to give …	Integer32r/w Constraints: range: 1-255	.0.22.1.12
ipQoSDirection This object specifies the direction for witch this classifier rule applies on this interface, possible values: outgoing(1) = used for outgoing packets only incoming(2) = used for incoming packets only both(3) = used fo…	Enumerationr/w	.0.22.1.13
ipQoSTosSetRateLimitationobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: This field specifies a rate limitation for the packe…	Enumerationr/w	.0.22.1.14
ipQoSTosSetRateBpsobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Maximum amount of trafic in bits per second that sho…	bpsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.22.1.15
ipQoSTosSetBurstBpsobsolete WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Maximum amount of additional trafic to the ipQoSTosS…	bpsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.22.1.16
ipQoSClassifyAction This object specifies the action to be performed if the associated filter matches. If set to disabled the filter is not consulted and the next rule is processed immediately, possible values: classify(1) = filter matc…	Enumerationr/w	.0.22.1.17
ipQoSExceedRateLimitation This field specifies a rate limitation between in-profile and out-profile datagrams. Possible values: none(1) = no limitation is defined. packets(2) = a limitation is defined in number of packets per second. t…	Enumerationr/w	.0.22.1.18
ipQoSExceedRate Maximum amount of packets per second that are considered in-profile. Packets in excess of (ipQosExceedRate + ipQosExceedBurst) are considered out-profile.	Integer32r/w Constraints: range: 0-65535	.0.22.1.19
ipQoSExceedBurst Maximum additional amount of packets per second that are considered in-profile. Packets in excess of (ipQosExceedRate + ipQosExceedBurst) are considered out-profile.	Integer32r/w Constraints: range: 0-65535	.0.22.1.20
ipQoSExceedRateBps Maximum amount of traffic in bits per second that is considered in-profile. Traffic in excess of (ipQosExceedRateBps + ipQosExceedBurstBps) is considered out-profile.	bpsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.22.1.21
ipQoSExceedBurstBps Maximum amount of additional traffic that is considered in-profile. Traffic in excess of (ipQosExceedRateBps + ipQosExceedBurstBps) is considered out-profile.	bpsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.22.1.22
ipQoSTosAndMask AND mask applied to TOS field inside IP header of in-profile datagrams.	Integer32r/w Constraints: range: 0-255	.0.22.1.23
ipQoSTosOrMask OR mask applied to TOS field inside IP header of in-profile datagrams.	Integer32r/w Constraints: range: 0-255	.0.22.1.24
ipQoSLevel2PrioAndMask AND mask applied to level 2 priority associated with in-profile datagrams.	Integer32r/w Constraints: range: 0-7	.0.22.1.25
ipQoSLevel2PrioOrMask OR mask applied to level 2 priority associated with in-profile datagrams.	Integer32r/w Constraints: range: 0-7	.0.22.1.26
ipQoSTosAndMaskExceed AND mask applied to TOS field inside IP header of out-profile datagrams.	Integer32r/w Constraints: range: 0-255	.0.22.1.27
ipQoSTosOrMaskExceed OR mask applied to TOS field inside IP header of out-profile datagrams.	Integer32r/w Constraints: range: 0-255	.0.22.1.28
ipQoSLevel2PrioAndMaskExceed AND mask applied to level 2 priority associated with out-profile datagrams.	Integer32r/w Constraints: range: 0-7	.0.22.1.29
ipQoSLevel2PrioOrMaskExceed OR mask applied to level 2 priority associated with out-profile datagrams.	Integer32r/w Constraints: range: 0-7	.0.22.1.30
ipQoSDescr A textual string describing this classifier rules.	OctetStringr/w Constraints: range: 0-255	.0.22.1.31

The 'ipRipTimerTable' contains the basic configuration
of the RIP protocol. Formerly created to define only
the 3 timers involved in RIP process (cf RFC 2453).
          
This set of timers is unique for the router. Values
should be the same on all the routers of the whole network.

ipRipTimerEntry row .0.23.1

Indexes

ipRipVersion

Column	Syntax	OID
ipRipVersion RFC 2453, RIP Version 2.	Integer32 Constraints: range: 1-3	.0.23.1.1
ipRipTimerUpdate An unsollicited RIP response is broadcast every 'ipRipTimerUpdate' seconds.	secondsInteger32r/w Constraints: range: 1-65535	.0.23.1.2
ipRipTimerTimeout If 'ipRipTimerTimeout' seconds elapse from the last time an update message is received for this route, the route is dropped but keeped in routing table. Then 'garbage process' is started.	secondsInteger32r/w Constraints: range: 1-65535	.0.23.1.3
ipRipTimerGarbage If 'ipRipTimerGarbage' seconds elapse from the start of 'garbage process' (and if route is still 'dropped'), the route is removed from the routing table.	secondsInteger32r/w Constraints: range: 1-65535	.0.23.1.4
ipRipRfc2453Timer The 'ipRipRfc2453Timer' enabled/disables variable timer definition from RFC 2453.	Enumerationr/w	.0.23.1.5
ipRipRfc2091Timer The 'ipRipRfc2453Timer' enabled/disables variable timer definition from RFC 2091.	Enumerationr/w	.0.23.1.6
ipRipUpdatePacketRetryTimer If 'ipRipTimerUpdatePacketRetry' seconds elapse since the transmission of the last update packet without receiving an acknowledge the update packet is resend.	secondsInteger32r/w Constraints: range: 1-10	.0.23.1.7
ipRipPoisonedReverse Enable or disable the (currently unimplemented) control over 'poisoned reverse' route distribution.	Enumerationr/w	.0.23.1.8
ipRipDistributeDefaultRoutes Enable or disable the distribution of 'default routes'.	Enumerationr/w	.0.23.1.9
ipRipHoldDownTimer If 'ipRipHoldDownTimer' seconds elapse from the start of 'database timeout' (and if route is still 'dropped'), the route is removed from the routing table.	secondsInteger32r/w Constraints: range: 1-65535	.0.23.1.10

The ipRipFilterTable contains additional information related
to IP and the interfaces found on the system. Entries can only
be added or deleted by the system.

ipRipFilterEntry row .0.33.1

Indexes

ipRipFilterIfIndex ipRipFilterIpAddr ipRipFilterNetMask ipRipFilterPriority ipRipFilterDirection

Column	Syntax	OID
ipRipFilterEntryState makes entry active	Enumerationr/w	.0.33.1.1
ipRipFilterIfIndex The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.33.1.2
ipRipFilterIpAddr The IP-Address range affected by the filter operation. Ranges are separately defined for import and export. IP-Address ranges which are not matched by any filters pass the filter stage unmodified. If this isn't intended…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.33.1.3
ipRipFilterNetMask Indicate the mask to be logical-ANDed with the ip-address before being compared to the value in the ipRipFilterIpAddr field. If a subnet mask is not specified, it will be set automatically according to the following tab…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.33.1.4
ipRipFilterPriority If more than one filter matches the IP-Address range this priority decides which filter to apply. 1 indictes highest priority and 16 lowest priority	Integer32r/w Constraints: range: 1-16	.0.33.1.5
ipRipFilterDirection The direction the filter is defined for.	Enumerationr/w	.0.33.1.6
ipRipFilterDistribution Include or exclude the IP-Address range from distribution.	Enumerationr/w	.0.33.1.7
ipRipFilterMetric1IfUpOffset Add 'ipRipFilterMetric1IfUpOffset' to metric1 during import of this route if the operation status of this interface is up. On export, add 'ipRipFilterMetric1IfUpOffset' to the exported metric value if the operation stat…	Integer32r/w Constraints: range: -16-16	.0.33.1.8
ipRipFilterMetric1IfDormantOffset Add 'ipRipFilterMetric1IfDormantOffset' to metric1 during import of this route if the operation status of this interface is dormant. On export, add 'ipRipFilterMetric1IfDormantOffset' to the exported metric value if the…	Integer32r/w Constraints: range: -16-16	.0.33.1.9

If NAT is switched on for an interface, this table contains
entries for expected sessions. Table entries are creates by 
the system whenever there is a need for a new incoming session.
Table entries are removed after timeout or if the expected
session is established.

ipNatExpEntry row .0.34.1

Indexes

ipNatExpIfIndex

Column	Syntax	OID
ipNatExpIfIndex This object specifies the interface, for which the session is expected. A value of 0 means ANY interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.34.1.1
ipNatExpProtocol This object specifies the protocol, the expected session is using.	Enumeration	.0.34.1.2
ipNatExpIntAddr This object specifies the internal local IP Address used for the expected session.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.34.1.3
ipNatExpIntPort This object specifies the internal local port-number used for the expected session. A value of -1 means to copy the related external port-number without any NAT-translation.	Integer32 Constraints: range: -1-65535	.0.34.1.4
ipNatExpExtAddr This object specifies the external local address used for the expected session. A value of 0.0.0.0 means ANY address.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.34.1.5
ipNatExpExtPort This object specifies the external local port-number used for the expected session. A value of -1 means ANY port-number.	Integer32 Constraints: range: -1-65535	.0.34.1.6
ipNatExpRemoteAddr This object specifies the remote IP-address used for the expected session. A value of 0.0.0.0 means ANY address.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.34.1.7
ipNatExpExtPortType This field is used for NAT-internal signalling. Applications shall set it to <supplied>. For automatically generated, NAT-out-triggered entries, the system sets this field to <pool> temporarily when the related ExtPort-…	Enumeration	.0.34.1.8
ipNatExpRemotePort This object specifies the remote port-number used for the expected session. A value of -1 means ANY port number.	Integer32 Constraints: range: -1-65535	.0.34.1.9
ipNatExpTimeout Set a specific Timeout in seconds for a new expected session. A value of 0 means UNSPECIFIED (default-value is taken).	secondsInteger32 Constraints: range: 0-86400	.0.34.1.10

Entries in the Multicast Forwarding Table define a rule
where to forward packets with a specified multicast group address
to a dedicated destination interface.

mcastFwdEntry row .0.53.1

An entry in the Multicast Forwarding Table.

Indexes

mcastFwdAddress

Column	Syntax	OID
mcastFwdAddress The multicast forwarding group address which will be forwarded. The group address 224.0.0.0 may be used as a wildcard matching all addresses.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.53.1.1
mcastFwdSrcIfIndex The source interface of incoming multicast packets.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.53.1.2
mcastFwdDestIfIndex The destination interface where to forward multicast packets.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.53.1.3
mcastFwdStatus The status of this entry.	Enumerationr/w	.0.53.1.4

.

ipLfiEntry row .0.57.1

Indexes

ipLfiIfIndex

Column	Syntax	OID
ipLfiIfIndex This object specifies the associated interface.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.57.1.1
ipLfiMode This object enables Link Framentation and Interleave (LFI) mode on the associated interface.	Enumerationr/w	.0.57.1.2
ipLfiMaxFragSize This object specifies the current maximum fragment size used for Link Fragmentation and Interleave (LFI) mode on the associated interface.	bytesInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.57.1.10
ipLfiMinFragSize This object specifies the current minimum fragment size used for Link Fragmentation and Interleave (LFI) mode on the associated interface.	bytesInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.57.1.11
ipLfiCurrVoipCalls The current number of VoIP Calls routed via the associated interface.	Integer32r/w Constraints: range: 0-64	.0.57.1.12

This table specifies the IP addresses and port numbers 
for sessions that must not be processed by NAT.		 
          
Entries in the table are created and removed manually
by network management.

ipNatExcludeEntry row .0.60.1

Indexes

ipNatExIfIndex ipNatExProtocol ipNatExLocalPort ipNatExRemotePort

Column	Syntax	OID
ipNatExIfIndex This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use NAT.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.60.1.1
ipNatExProtocol This object specifies the protocol, for which the table entry shall be valid.	Enumerationr/w	.0.60.1.2
ipNatExLocalAddr This object specifies together with ipNatExLocalMask the set of IP addresses of local hosts involved in the communication. The table entry will be valid when the IP address of the local host lies in the range specifi…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.60.1.3
ipNatExLocalMask This object specifies together with ipNatExLocalAddr the set of IP addresses of local hosts involved in the communication. The table entry will be valid when the IP address of the local host lies in the range specifi…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.60.1.4
ipNatExLocalPort This object specifies together with ipNatExLocalPortRange the range of local portnumbers, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all local portnumbers. If ipNa…	Integer32r/w Constraints: range: -1-65535	.0.60.1.5
ipNatExLocalPortRange This object specifies together with ipNatExLocalPort the range of local portnumbers, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all local portnumbers. If ipNatExLo…	Integer32r/w Constraints: range: -1-65535	.0.60.1.6
ipNatExRemoteAddr This object specifies together with ipNatExRemoteMask the set of IP addresses of remote hosts involved in the communication. The table entry will be valid when the IP address of the remote host lies in the range spec…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.60.1.7
ipNatExRemoteMask This object specifies together with ipNatExRemoteAddr the set of IP addresses of remote hosts involved in the communication. The table entry will be valid when the IP address of the remote host lies in the range spec…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.60.1.8
ipNatExRemotePort This object specifies together with ipNatExRemotePortRange the range of remote portnumbers, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all remote portnumbers. If i…	Integer32r/w Constraints: range: -1-65535	.0.60.1.9
ipNatExRemotePortRange This object specifies together with ipNatExRemotePort the range of remote portnumbers, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all remote portnumbers. If ipNatE…	Integer32r/w Constraints: range: -1-65535	.0.60.1.10
ipNatExDescr A textual string describing this NAT excluding rule.	OctetStringr/w Constraints: range: 0-255	.0.60.1.11
ipNatExAction This object specifies which packets will be excluded from NAT processing. When set to 'exclude' (default value), any packet matching the parameters of the entry will be excluded from NAT processing. When set to 'excl…	Enumerationr/w	.0.60.1.12

This table displays all currently active IP address translation
policies in 'outgoing' direction. It's similar to the former
defined ipNatOutTable.
Table entries are created:
- either by the IP subsystem itself due to the
  administratively-defined ipNatOutTable entries
  (ipNatOutOperType_permanent(1))
- or by several subsystems whenever there is a need for such
  non-static NAT policies (ipNatOutOperType_temporary(2))
          
Table entries are deleted:
- either by the IP subsystem itself due to the
  administratively-defined ipNatOutTable entries
  (ipNatOutOperType_permanent(1))
- or by several subsystems whenever there is a need for such
  non-static NAT policies (ipNatOutOperType_temporary(2))
- or, in case of non-permanent entries, by the administrator
          
If no matching entry is found (neither in the IP address is
set to the IP address defined on the interface configured for
NAT. If a matching entry is found, the source IP address of
outgoing IP packets is translated according to the couple
'ipNatOutOperExtAddr /ipNatOutOperExtMask'.
          
- If external IP address is a 'host IP address', the
 whole source IP address is mapped.
- If external IP address is a 'net IP address', only
 the 'net part' of source IP address is affected.
This table is only used if the outgoing address
translation is activated (ipExtIfNatOutXlat).

ipNatOutOperEntry row .0.61.1

Indexes

ipNatOutOperIfIndex ipNatOutOperIntAddr ipNatOutOperExtAddr

Column	Syntax	OID
ipNatOutOperIfIndex This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use NAT.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.1
ipNatOutOperProtocol This object specifies the protocol, for which the table entry shall be valid.	Enumeration	.0.61.1.2
ipNatOutOperRemoteAddr This object specifies together with ipNatOutOperRemoteMask the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.0, the table entry will be valid for any target IP address.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.61.1.3
ipNatOutOperRemoteMask This object specifies together with ipNatOutOperRemoteAddr the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.0, the table entry will be valid for any target IP address.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.61.1.4
ipNatOutOperExtAddr With ipNatOutOperExtMask, this object specifies the external 'IP address' or 'NET address' to which the internal IP address is mapped. - To map exactly to ipNatOutOperExtAddr (i.e. map to a single IP addr…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.61.1.5
ipNatOutOperRemotePort This object specifies together with ipNatOutRemotePortRange the range of portnumbers for outgoing packets, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all portnumbers.…	Integer32 Constraints: range: -1-65535	.0.61.1.6
ipNatOutOperRemotePortRange This object specifies together with ipNatOutOperRemotePort the range of portnumbers for outgoing packets, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all portnumbers. …	Integer32 Constraints: range: -1-65535	.0.61.1.7
ipNatOutOperIntAddr This object specifies together with ipNatOutOperIntMask the internal hosts IP address for outgoing packets matching the table entry. If both objects are set to 0.0.0.0, the table entry will be valid for any source IP ad…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.61.1.8
ipNatOutOperIntMask This object specifies together with ipNatOutOperIntAddr the internal hosts IP address for outgoing packets matching the table entry. If both objects are set to 0.0.0.0, the table entry will be valid for any source IP ad…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.61.1.9
ipNatOutOperIntPort This object specifies the internal source port for which the table entry shall be valid. If this object is set to -1, any internal source port matches this entry.	Integer32 Constraints: range: -1-65535	.0.61.1.10
ipNatOutOperExtPort This object may be used to specify a fixed external source port to which the internal source port is mapped. If this object is set to -1, the port is mapped to the next free source port available.	Integer32 Constraints: range: -1-65535	.0.61.1.11
ipNatOutOperExtMask With ipNatOutOperExtAddr, this object specifies the external 'IP address' or 'NET address' to which the internal IP address is mapped. - To map exactly to ipNatOutOperExtAddr (i.e. map to a single IP addr…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.61.1.12
ipNatOutOperTimeout When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. If set to the default value of 0, the timeout will be set to …	secondsInteger32 Constraints: range: 0-5184000	.0.61.1.13
ipNatOutOperType Specifies whether there is an associated ipNatOutTable entry (permanent) or not (temporary). Note that entries with type permanent (1) cannot be deleted by the administrator directly.	Enumeration	.0.61.1.14
ipNatOutOperParent Row number of the associated ipNatOutTable entry.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.15
ipNatOutOperNatCategory Specifies the NAT category according RFC 3489 and 5389 to be applied for UDP traffic matching with this entry.	Enumeration	.0.61.1.16
ipNatOutOperIntPortRange This object specifies together with ipNatOutOperIntPort the internal source port range for which the table entry shall be valid. If this object is set to -1, only ipNatOutOperIntPort is used as selector for this entry.	Integer32 Constraints: range: -1-65535	.0.61.1.17
ipNatOutOperExtPortRange This object may be used together with ipNatOutOperExtPort to specify a fixed external source port number range to which the internal source port numbers are mapped. This mapping depends on the position of the original s…	Integer32 Constraints: range: -1-65535	.0.61.1.18

This table specifies the IP addresses and port numbers
for sessions requested from outside. If this table is
empty and NAT is enabled, only packets for sessions
initiated from inside are forwarded.
It's similar to the former defined ipNatPresetTable.
          
The IP address and the port number of the internal server
can be specified individually for each combination of
- protocol (udp/tcp/icmp)
- initiating hosts IP address (RemoteAddr, RemoteMask)
- destination address or network (ExtAddr, ExtMask)
- destination port number or range (ExtPort, ExtPortRange)
          
Entries in the table are created:
- either by the IP subsystem itself due to the
   administratively-defined ipNatPresetTable entries
  (ipNatPresetOperType_permanent(1))
- or by several subsystems whenever there is a need for such
 non-static NAT policies (ipNatPresetOperType_temporary(2))
          
Entries are deleted:
- either by the IP subsystem itself due to the
  administratively-defined ipNatPresetTable entries
  (ipNatPresetOperType_permanent(1))
- or by several subsystems whenever there is a need for such
  non-static NAT policies (ipNatPresetOperType_temporary(2))
- or, in case of non-permanent entries, by the administrator.

ipNatPresetOperEntry row .0.63.1

Indexes

ipNatPrOperIfIndex ipNatPrOperProtocol ipNatPrOperExtPort

Column	Syntax	OID
ipNatPrOperIfIndex This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use NAT.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.63.1.1
ipNatPrOperProtocol This object specifies the protocol, for which the table entry shall be valid.	Enumeration	.0.63.1.2
ipNatPrOperRemoteAddr This object specifies together with ipNatPrOperRemoteMask the the set of IP addresses of remote hosts initiating a session. The table entry will be valid for an incoming packet, when the IP adress of the remote host ini…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.63.1.3
ipNatPrOperRemoteMask This object specifies together with ipNatPrOperRemoteAddr the set of IP addresses of remote hosts initiating the session. The table entry will be valid for an incoming packet, when the IP adress of the remote host initi…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.63.1.4
ipNatPrOperExtAddr This object specifies together with ipNatPrOperExtMask the set of destination IP addresses, for which the table entry shall be valid. The entry is valid, if the target IP address of an incoming IP packet lies in the ran…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.63.1.5
ipNatPrOperExtMask This object specifies together with ipNatPrOperExtAddr the set of destination IP addresses, for which the table entry shall be valid. The entry is valid, if the target IP address of an incoming packet lies in the range …	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.63.1.6
ipNatPrOperExtPort This object specifies together with ipNatPrOperExtPortRange the range of portnumbers for incoming packets, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all portnumbers.…	Integer32 Constraints: range: -1-65535	.0.63.1.7
ipNatPrOperExtPortRange This object specifies together with ipNatPrOperExtPort the range of portnumbers for incoming packets, for which the table entry shall be valid. If both objects are set to -1, the entry is valid for all portnumbers. If i…	Integer32 Constraints: range: -1-65535	.0.63.1.8
ipNatPrOperIntAddr With ipNatPrOperIntMask, this object specifies the internal target host's IP address for incoming packets matching the table entry. An incoming packet matching this entry will be routed to the internal s…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.63.1.9
ipNatPrOperIntPort This object specifies the internal target host's port-number for incoming packets matching the table entry. If this object is set to -1, the target portnumber will be taken from the original incoming packet. No translat…	Integer32 Constraints: range: -1-65535	.0.63.1.10
ipNatPrOperIntMask With ipNatPrOperIntAddr, this object specifies the internal target host's IP address for incoming packets matching the table entry. An incoming packet matching this entry will be routed to the internal s…	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.63.1.11
ipNatPrOperTimeout When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. If set to the default value of 0, the timeout will be set …	secondsInteger32 Constraints: range: 0-5184000	.0.63.1.12
ipNatPrOperTcpOption Additional selector, increases the prossible granularity of the TCP-related NAT preset rules. This parameter doesn't matter if not set, in all other cases initial TCP SYN messages without the associated TCP option will …	Bits	.0.63.1.13
ipNatPrOperType Specifies whether there is an associated ipNatPrestTable entry (permanent) or not (temporary). Note that entries with type permanent (1) cannot be deleted by the administrator directly.	Enumeration	.0.63.1.14
ipNatPrOperParent Row number of the associated ipNatPresetTable entry.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.63.1.15

The ipWolRuleTable defines access rules for checking incoming
IP packets. The rules are processed in order, i.e. each rule
has a link to the next rule. The set of rules is processed
until a match occurs, that means the rule's associated filter 
matches and the specified action is performed (either send a 
Wake-On-LAN packet via Ethernet or via UDP). The last rule is
implicitly a deny rule. The set of rules to be processed can be
defined	for each interface.

ipWolRuleEntry row .0.67.1

Indexes

ipWolRuleFilterIndex

Column	Syntax	OID
ipWolRuleIndex Unique rule index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.67.1.1
ipWolRuleFilterIndex References the rule's associated filter.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.67.1.2
ipWolRuleAction This object specifies the action to be performed if the rule's associated filter matches. If set to ignore the filter is not consulted and the next rule is processed immediately. invoke, invoke WoL if f…	Enumerationr/w	.0.67.1.3
ipWolRuleNextRuleIndex Specifies the next rule to be processed. The value 0 is used to mark the end of the rule set.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.67.1.4
ipWolRuleWolType Which Wake-On-LAN standard should be used.	Enumerationr/w	.0.67.1.5
ipWolRuleTarget The mac address of the interface to be woken up.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.0.67.1.6
ipWolRulePassword Wake-On-LAN password. The password length is either 0, 4 or 6.	OctetStringr/w Constraints: range: 0-6	.0.67.1.7
ipWolRuleDescr A textual string describing this Wake-On-LAN rule.	OctetStringr/w Constraints: range: 0-255	.0.67.1.8
ipWolRuleTargetIfIndex The index value which uniquely identifies Wake-On-LAN outbound interface.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.67.1.9