BINTEC-AUX-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
2
Rows
2
Columns
29

auxConfigTable

table
.0.3.1.10 · 1 row entry · 13 columns
Open in standard view
Uses the bintec variant from /opt/observium/mibs/bintec.
Command help
Walk auxConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'BINTEC-AUX-MIB' -M '/opt/observium/mibs/bintec:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'BINTEC-AUX-MIB::auxConfigTable' 
The auxConfigTable configures each corresponding aux device.
auxConfigEntry row .0.3.1.10.1
A single auxConfigTable entry.
Indexes
Column Syntax OID
auxConfigIfIndex
The index of the corresponding tty interface.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .0.3.1.10.1.1
auxConfigSpeed
The speed of the aux device. The default value is 9600.
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.3.1.10.1.2
auxConfigPIN
The PIN code of the SIM card. This is used to
authorize the access to the SIM card.
OctetStringr/w
Constraints:
range: 0-8
 .0.3.1.10.1.3
auxConfigModulation
The Modulation used by the modem.
With auto(1) the modulation will be automatically chosen.
mdm_9600(2) sets the modulation to 9600 bps (V.32).
mdm_14400(3) sets the modulation to 14400 bps (V.34).
The values v110_9600(…
Enumerationr/w
Enumerated Values:
1auto
2mdm-9600
3mdm-14400
4v110-9600
5v110-14400
6v120
7gprs
 .0.3.1.10.1.4
auxConfigDispatch
The dispatch service the modem should be used for.
The service could be either ppp(1), isdnlogin(2) or
none.
Enumerationr/w
Enumerated Values:
1ppp
2isdnlogin
3none
 .0.3.1.10.1.5
auxConfigAPN
GPRS Access Point Name (APN).
OctetStringr/w
Constraints:
range: 0-80
 .0.3.1.10.1.6
auxConfigInit
Additional Modem init sequence.
This sequence will be send to the modem to initialize it.
Normally this string should be empty (un-used).
OctetStringr/w
Constraints:
range: 0-80
 .0.3.1.10.1.7
auxConfigEscape
Modem escape character.
This character is sent to the modem to terminate the session.
For GPRS/UMTS modems this parameter should be zero.
Integer32r/w
Constraints:
range: 0-255
 .0.3.1.10.1.8
auxConfigAccessType
The default Access Type used by a GPRS/UMTS modem.
This setting works only for vendors who publish the
AT commands needed offically in the internet.
Enumerationr/w
Enumerated Values:
1auto
2gprs-only
3umts-only
4gprs-pref
5umts-pref
 .0.3.1.10.1.9
auxConfigPUK
The PUK code of the SIM card needed to reset
the PIN code if the PIN is invalidated.
This is used to enter a new PIN code.
The PUK isn't stored in the configuration for
security reasons and used only temporarily
if avai…
OctetStringr/w
Constraints:
range: 0-16
 .0.3.1.10.1.10
auxConfigPinData
Field used for storing the PIN permanently.
OctetString
Constraints:
range: 0-16
 .0.3.1.10.1.11
auxConfigRoamingMode
The Roaming configuration for this TTY interface.
Possible values are:
disabled - no roaming at all
auto - roaming decision by modems factory defaults
unrestricted - no restrictions for roamin…
Enumerationr/w
Enumerated Values:
1disabled
2auto
3unrestricted
4international
5national
6fixed
 .0.3.1.10.1.12
auxConfigRoamingPLMN
The PLMN (Public Land Mobile Netword) code allowed for
Roaming. Used only if auxConfigRoamingMode_fixed is selected.
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.3.1.10.1.13

auxStatTable

table
.0.3.1.11 · 1 row entry · 16 columns
Open in standard view
Uses the bintec variant from /opt/observium/mibs/bintec.
Command help
Walk auxStatTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'BINTEC-AUX-MIB' -M '/opt/observium/mibs/bintec:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'BINTEC-AUX-MIB::auxStatTable' 
The auxStatTable holds statistics about the corresponding 
aux device.
auxStatEntry row .0.3.1.11.1
A single auxStatTable entry.
Indexes
Column Syntax OID
auxStatIfIndex
The index of the corresponding tty interface.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .0.3.1.11.1.1
auxStatOperStatus
The operational status of the GSM modem. The following
states can occur:
- up(1) the device is up - initialization finished
- down(2) the device is down
- init(3) initialization state
- cal…
Enumeration
Enumerated Values:
1up
2down
3init
4called
5calling
6connect
7simwait
8pinwait
9error
10disconnected
11pukwait
12regwait
13apnwait
 .0.3.1.11.1.2
auxStatErrorCode
If an error occurs (OperStatus is set to error) this variable
shows the reason for the error. Currently the following error
codes are possible:
- none(1) no error occured
- unspecified(2) error can't be specified…
Enumeration
Enumerated Values:
1none
2unspecified
3pinerror
4pukerror
5apnerror
6simerror
7reg-denied
 .0.3.1.11.1.3
auxStatNetwork
The name of the PLMN (Public Land Mobile Network)
actually being used.
OctetString
Constraints:
range: 0-60
 .0.3.1.11.1.4
auxStatCommand
The last Command that was sent to the Modem.
OctetString
Constraints:
range: 0-40
 .0.3.1.11.1.5
auxStatAnswer
The last Answer gotten from the Modem.
OctetString
Constraints:
range: 0-60
 .0.3.1.11.1.6
auxStatCSQ
The GSM receive signal level in decibel (db).
A value below -100 signals a very low signal quality.
A value between -100 and -80 means that signal quality is low.
If the value is between -80 and -70 the quality is ok. T…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .0.3.1.11.1.7
auxStatControlChannelobsolete
If the UMTS card provides several channels and one could
be used to control the card e.g. get status information
from the card like the signal quality a dedicated daemon
will do this and the auxStatControlChannel will b…
Enumeration
Enumerated Values:
1not-available
2available
 .0.3.1.11.1.8
auxStatAccessTypeobsolete
The Access Type the modem actually registers on.
Normally the `edge' or `hs*pa' Access Types aren't
provided in detail by the operator.
Enumeration
Enumerated Values:
1unknown
2gsm
3compact-gsm
4umts
5gsm-edge
6umts-hsdpa
7umts-hsupa
8umts-hspa
 .0.3.1.11.1.9
auxStatInDiscards
The number of frames which can't be enqueued upstream.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .0.3.1.11.1.10
auxStatHomePLMN
The PLMN (Public Land Mobile Network) code of the Home PLMN.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .0.3.1.11.1.11
auxStatCurrentPLMN
The PLMN (Public Land Mobile Network) code of the Network
currently used.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .0.3.1.11.1.12
auxStatIMEIobsolete
The IMEI (International Mobile Equipment Identity)
of the detected GSM/UMTS device.
OctetString
Constraints:
range: 0-32
 .0.3.1.11.1.13
auxStatIccIdobsolete
The ICC-ID of the SIM-Card found in the device
which is actually enumerated with auxStatIfIndex.

Some UMTS modem vendors offer no capability to
read this ID before entering a valid PIN :-(
In this case th…
OctetString
Constraints:
range: 0-32
 .0.3.1.11.1.14
auxStatLocationAreaCode
The actual Location Area Code the UMTS-Modem is registered.
This may differ for GSM/UMTS Access Technology.
OctetString
Constraints:
range: 0-16
 .0.3.1.11.1.15
auxStatCellId
The actual Cell-ID the UMTS-Modem is registered.
This may differ for GSM/UMTS Access Technology.
OctetString
Constraints:
range: 0-16
 .0.3.1.11.1.16