BIANCA-BRICK-WIRELESS-CONTROLLER-MIB Table View

This table lists the IP address type 
and the IP address of the AC

wlcACAddressEntry row .0.61.1.2.1

Indexes

wlcACAddressIndex

Column	Syntax	OID
wlcACAddressIndex Unique index of an accessible AC.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.2.1.1
wlcACAddressInetType IP address type. Possible values are: -unknown(0): an unknown address type -ipv4(1) : an IPv4 address -ipv6(2) : an IPv6 address -ipv4z(3) : a non-global IPv4 address including a zone index -ipv6z…	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.0.61.1.2.1.2
wlcACAddressInetAddress The IP address of the accessbile AC.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.61.1.2.1.3
wlcACAddressAdminStatus Enable, disable or delete the requested AC address.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled 32 delete	.0.61.1.2.1.4

The wlcWTPTable contains information relating to the WTPs
currently managed by our Access Controller (AC).
Each entry corresponds to a managed Wireless Termination Point
(WTP). Entries can be added or deleted by the user.

wlcWTPEntry row .0.61.1.3.1

Indexes

wlcWTPIndex

Column	Syntax	OID
wlcWTPIndex Unique index for the WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.3.1.1
wlcWTPAdminStatus Enable, disable or delete the requested WTP.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled 32 delete	.0.61.1.3.1.2
wlcWTPOperStatus This notification shows if the WTP is currently operative.	Enumeration Enumerated Values: 1 disabled 2 enabled 3 initialising 4 no-license-available	.0.61.1.3.1.3
wlcWTPMacAddress First ethernet MAC address of the WTP.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.0.61.1.3.1.4
wlcWTPDescription Description of the requested WTP.	OctetStringr/w Constraints: range: 0-63	.0.61.1.3.1.5
wlcWTPName Name of the requested WTP.	OctetStringr/w Constraints: range: 0-63	.0.61.1.3.1.6
wlcWTPLocation Location of the requested WTP.	OctetStringr/w Constraints: range: 0-63	.0.61.1.3.1.7
wlcWTPAdminSwVer This variable displays the current software version of each WTP	OctetStringr/w Constraints: range: 0-31	.0.61.1.3.1.8
wlcWTPEncryption Enable or disable the encryption between AC and WTP.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.0.61.1.3.1.9
wlcWTPTriggerStat Setting this variable to update(2) the WTP is triggered to send statistics (VSS, ACLDenied, stations, ...). After the trigger is sent it is switched back to idle(1). Default is idle(1).	Enumerationr/w Enumerated Values: 1 idle 2 update	.0.61.1.3.1.10
wlcWTPsecIndex This attribute shows the currently configured secIndex of the requested WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.3.1.11
wlcWTPauthEapolIndex This attribute shows the currently configured EapolIndex of the requested WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.3.1.12
wlcWTPglobalIndex This attribute shows the currently configured globalIndex of the requested WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.3.1.13
wlcWTPradiusSrvIndex This attribute shows the currently configured radiusSrvIndex of the requested WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.3.1.14
wlcWTPlogHostIndex This attribute shows the currently configured logHostIndex of the requested WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.3.1.15
wlcWTPscheduleIndex This attribute shows the currently configured scheduleIndex of the requested WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.3.1.16
wlcWTPlocalServicesIndex This attribute shows the currently configured localServicesIndex of the requested WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.3.1.17

This table delivers maintenance/debugging actions 
executed on the WTP

wlcWTPMaintenanceEntry row .0.61.1.4.1

Indexes

wlcWTPMaintenanceIndex

Column	Syntax	OID
wlcWTPMaintenanceIndex Index of WTP to be addressed with maintenance command.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.4.1.1
wlcWTPMaintenanceState This variable displays the current maintenance state of each WTP: idle: idle state start: start maintenance event (get state file or do update) running: maintenance event is running rebooting: WTP is reb…	Enumerationr/w Enumerated Values: 1 idle 2 start 3 running 4 done 5 error 6 stopped 7 rebooting 32 delete	.0.61.1.4.1.2
wlcWTPMaintenanceCommand Type of action performed on WTP software: software update state: get state file	Enumerationr/w Enumerated Values: 1 state 2 software	.0.61.1.4.1.3
wlcWTPMaintenanceURL Contains URL of the http or tftp server. Depending on wlcWTPMaintenanceCommand it serves for either destination (command state) or source (command software).	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.0.61.1.4.1.4

The wlcSecProfileTable describes profiles 
for different security settings.

wlcSecProfileEntry row .0.61.1.5.1

Indexes

wlcSecProfileIndex

Column	Syntax	OID
wlcSecProfileIndex Unique index of a security profile.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.5.1.1
wlcSecProfileAdminStatus Enable or delete the requestes security profile.	Enumerationr/w Enumerated Values: 1 enabled 32 delete	.0.61.1.5.1.2
wlcSecProfileAdminCommunity The Community name used for admin access.	OctetStringr/w Constraints: range: 0-63	.0.61.1.5.1.3
wlcSecProfileReadCommunity The Community name used for read-only access.	OctetStringr/w Constraints: range: 0-63	.0.61.1.5.1.4
wlcSecProfileWriteCommunity The Community name used for read-write access.	OctetStringr/w Constraints: range: 0-63	.0.61.1.5.1.5

This table combines WTP with the RADIUS service profile.

wlcRadiusSrvEntry row .0.61.1.6.1

Indexes

wlcRadiusSrvIndex

Column	Syntax	OID
wlcRadiusSrvIndex This variable contains the unique WTP index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.6.1.1
wlcRadiusSrvAdminStatus Enable or delete the RADIUS service profile from the requested WTP.	Enumerationr/w Enumerated Values: 1 enabled 32 delete	.0.61.1.6.1.2
wlcRadiusSrvProfIndex This variable contains the unique RADIUS service profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.6.1.3

The wlcRadiusSrvProfileTable describes different 
RADIUS service profiles.

wlcRadiusSrvProfileEntry row .0.61.1.7.1

Indexes

wlcRadiusSrvProfileIndex

Column	Syntax	OID
wlcRadiusSrvProfileIndex Unique index of a RADIUS service profile.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.7.1.1
wlcRadiusSrvProfileAddressType The IP address type of the requested RADIUS service can be: -unknown(0): an unknown address type -ipv4(1) : an IPv4 address -ipv6(2) : an IPv6 address -ipv4z(3) : a non-global IPv4 address including a zone …	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.0.61.1.7.1.2
wlcRadiusSrvProfileAddress The RADIUS Server IP Address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.61.1.7.1.3
wlcRadiusSrvProfilePort The RADIUS server authentication port. Please notice that RFC2138 assigns ports 1812 and 1813 for authentication and accounting, respectively. Many RADIUS servers still use the formerly assigned ports 1645 and 1646 inst…	Integer32r/w Constraints: range: 0-65535	.0.61.1.7.1.4
wlcRadiusSrvProfileSecret The shared secret between RADIUS server and Brick.	OctetStringr/w Constraints: range: 0-63	.0.61.1.7.1.5
wlcRadiusSrvProfilePriority The RADIUS server with the lowest priority is the first used for request. If there is no response (see also the values Timeout and Retries) the RADIUS server with the next lowest priority will be used.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.7.1.6
wlcRadiusSrvProfileTimeout The amount of milliseconds (1/1000s) waiting for an outstanding request.	millisecondsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.7.1.7
wlcRadiusSrvProfileRetries The number of retries sent for each request, until the server state is set to inactive. Default value is 1. To prevent the radiusSrvState ever switch to inactive, set this value to 0.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.7.1.8
wlcRadiusSrvProfileState When operational, the server state is active(1). If the RADIUS server does not respond, its state is set to inactive(2). The administrator can set the state manually to disabled(3), or delete(32) the entry.	Enumerationr/w Enumerated Values: 1 active 2 inactive 3 disabled 32 delete	.0.61.1.7.1.9
wlcRadiusSrvProfileKeepAlive Enables the periodicaly keep alive check of 'inactive' (see radiusSrvState) server.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.7.1.10

The wlcRadiusSrvProfileTable describes 
different auth eapol profiles.

wlcAuthEapolProfileEntry row .0.61.1.8.1

Indexes

wlcAuthEapolProfileIndex

Column	Syntax	OID
wlcAuthEapolProfileIndex Unique index of a auth eapol profile.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.8.1.1
wlcAuthEapolProfileAdminStatus Enable or delete the requested auth eapol profile.	Enumerationr/w Enumerated Values: 1 enabled 32 delete	.0.61.1.8.1.2
wlcAuthEapolProfilePTK1Timeout The time after which the first EAPOL-key Message in the pairwise temporal key negotiation phase (PTK1) is retransmitted if there is no reply from supplicant. Time can be changed in steps of 100 milliseconds.	millisecondsInteger32r/w Constraints: range: 100-30000	.0.61.1.8.1.3
wlcAuthEapolProfilePTK3Timeout The time after which the third EAPOL-key Message in the pairwise temporal key negotiation phase (PTK3) is retransmitted if there is no reply from supplicant. Time can be changed in steps of 100 milliseconds.	millisecondsInteger32r/w Constraints: range: 100-30000	.0.61.1.8.1.4
wlcAuthEapolProfileGTKTimeout The time after which the first EAPOL-key Message in the group temporal key negotiation phase (GTK) is retransmitted if there is no reply from supplicant. Time can be changed in steps of 100 milliseconds.	millisecondsInteger32r/w Constraints: range: 100-30000	.0.61.1.8.1.5
wlcAuthEapolProfilePairwiseUpdateCount The number of times EAPOL Message 1 and Message 3 in the pairwise temporal key negotiation phase (PTK) will be retried.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.8.1.6
wlcAuthEapolProfileGroupUpdateCount The number of times Message 1 in the group temporal key negotiation phase (GTK) will be retried.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.8.1.7
wlcAuthEapolProfileAuthPeriod The time after a disassociation/deauthentication should be committed by the client if there is no EAPOL Message from authenticator. Time can be changed in steps of 1 seconds.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.8.1.8
wlcAuthEapolProfileQuietPeriod Period of time during which the authenticator will not attempt to acquire a supplicant. Time can be changed in steps of 1 seconds. Default value is 60 seconds.	sInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.8.1.9
wlcAuthEapolProfileTxPeriod A period used by the authenticator PAE state machine to determine when an EAPOL PDU is to be transmitted. Time can be changed in steps of 1 seconds. Default value is 30 seconds.	sInteger32r/w Constraints: range: 0-65535	.0.61.1.8.1.10
wlcAuthEapolProfileSuppTimeout A timeout used by the backend authentication state machine in order to determine timeout conditions in the exchanges between the authenticator and the supplicant. Time can be changed in steps of 1 seconds. Default val…	sInteger32r/w Constraints: range: 1-3600	.0.61.1.8.1.11
wlcAuthEapolProfileReAuthPeriod A period used by the reauthentication timer state machine to determine when reauthentication of the supplicant takes place. Time can be changed in steps of 1 seconds. Default value is 3600 seconds.	sInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.8.1.12
wlcAuthEapolProfileReAuthEnabled The state variable reAuthEnabled controls whether periodic reauthentication takes place. Default value is false.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.8.1.13
wlcAuthEapolProfileMaxReq The maximum number of times that the state machine will retransmit an EAP Request packet to the supplicant before it times out the authentication session. Default value is 2.	Integer32r/w Constraints: range: 1-10	.0.61.1.8.1.14
wlcAuthEapolProfileKeyTxEnabled The EAPOL protocol optionally supports the transmission of global key information from the Authenticator to the Supplicant, following a successful authentication exchange, in circumstances in which encryption is avail…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.8.1.15

This table cotains WTP debug level settings

wlcWTPGlobalProfileEntry row .0.61.1.9.1

Indexes

wlcWTPGlobalProfileIndex

Column	Syntax	OID
wlcWTPGlobalProfileIndex Unique index of a global profile.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.9.1.1
wlcWTPGlobalProfileDebugType Wireless LAN Controler degugging type. With type common(1) debugging messages of authentication, access_point, bridge and client handling will be shown. With type authentication(2) only messages concerning the authent…	Enumerationr/w Enumerated Values: 1 common 2 authentication 3 access-point 4 bridge 5 client 6 lowlevel 7 all	.0.61.1.9.1.3
wlcWTPGlobalProfileDebugLevel WLC degugging verbosity level. With a higher value more debugging information will be created. Default is normal(2).	Enumerationr/w Enumerated Values: 1 quiet 2 normal 3 verbose 4 very-verbose	.0.61.1.9.1.4
wlcWTPGlobalProfileAdminStatus WLC global AdminStatus. The AP could be used unmanaged(1) and must therefore be configured directly or managed(2) by a WLAN controller. Delete(32) deletes the required profile. Default is managed(1).	Enumerationr/w Enumerated Values: 1 unmanaged 2 managed 32 delete	.0.61.1.9.1.5

This table combines WTP with the log host profile.

wlcLogHostEntry row .0.61.1.10.1

Indexes

wlcLogHostIndex

Column	Syntax	OID
wlcLogHostIndex The wlcLogHostIndex is the unique WTP index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.10.1.1
wlcLogHostAdminStatus Enable or delete the log host profile from the requested WTP.	Enumerationr/w Enumerated Values: 1 enabled 32 delete	.0.61.1.10.1.2
wlcLogHostProfIndex This variable contains the unique log host profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.10.1.3

The wlcLogHostProfileTable contains profiles 
to list hosts which are to receive syslog messages.
This table also defines which types and levels of
messages to send.

wlcLogHostProfileEntry row .0.61.1.11.1

Indexes

wlcLogHostProfileIndex

Column	Syntax	OID
wlcLogHostProfileIndex Unique index of a loghost profile	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.11.1.1
wlcLogHostProfileAddrType The IP address type of the requested loghost. could be: -unknown(0): an unknown address type -ipv4(1) : an IPv4 address -ipv6(2) : an IPv6 address -ipv4z(3) : a non-global IPv4 address including a zone …	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.0.61.1.11.1.2
wlcLogHostProfileAddr IP Address where syslog messages are sent. If the facility is set to memory or console, this field is not used.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.0.61.1.11.1.3
wlcLogHostProfileLevel Priorities lower than or equal to this level are sent to loghost. The delete priority is used to discard the whole entry.	Enumerationr/w Enumerated Values: 1 emerg 2 alert 3 crit 4 err 5 warning 6 notice 7 info 8 debug 32 delete	.0.61.1.11.1.4
wlcLogHostProfileFacility The facility used for the syslog messages being generated.	Enumerationr/w Enumerated Values: 1 local0 2 local1 3 local2 4 local3 5 local4 6 local5 7 local6 8 local7	.0.61.1.11.1.5
wlcLogHostProfileType The subject of the messages that are to be generated. system means all subjects except accounting, all means all subjects.	Enumerationr/w Enumerated Values: 1 system 2 acct 3 all	.0.61.1.11.1.6
wlcLogHostProfileTimestamp This object describes the format of the timestamp. none(1) = no timestamp, time(2) = only time is printed, all(3) = date and time is printed.	Enumerationr/w Enumerated Values: 1 none 2 time 3 all	.0.61.1.11.1.7
wlcLogHostProfileMethod This object provides protocol for sending syslog messages: udp(1) = udp tcp(2) = tcp	Enumerationr/w Enumerated Values: 1 udp 2 tcp	.0.61.1.11.1.8

This table combines WTP with the schedule profile.

wlcScheduleEntry row .0.61.1.12.1

Indexes

wlcScheduleIndex

Column	Syntax	OID
wlcScheduleIndex This variable contains the unique WTP index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.12.1.1
wlcScheduleAdminStatus Enable or delete the schedule profile from the requested WTP.	Enumerationr/w Enumerated Values: 1 enabled 32 delete	.0.61.1.12.1.2
wlcScheduleProfIndex This variable contains the unique schedule profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.12.1.3

The wlcScheduleProfileTable contains different schedule profiles.

wlcScheduleProfileEntry row .0.61.1.13.1

Indexes

wlcScheduleProfileIndex

Column	Syntax	OID
wlcScheduleProfileIndex Unique schedule profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.13.1.1
wlcScheduleProfileAdminStatus Enable or delete the requested schedule profile.	Enumerationr/w Enumerated Values: 1 enabled 32 delete	.0.61.1.13.1.2
wlcScheduleProfileDescr This object specifies the description (name) of this entry. Only for information.	OctetStringr/w Constraints: range: 0-63	.0.61.1.13.1.3
wlcScheduleProfileAction This variable isn't in use right now.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.13.1.4
wlcScheduleProfileCondition This object specifies the condition when the event is active Time events (active at the time 'Start' until 'End'): daily : the time event is daily active at given time monday..sunday: the time event is we…	Enumerationr/w Enumerated Values: 1 greater 2 equal 3 less 4 notequal 5 range 6 daily 7 sunday 8 monday 9 tuesday 10 wednesday 11 thursday 12 friday 13 saturday 14 mon-fri 15 mon-sat 16 sat-sun 17 day1 18 day2 19 day3 20 day4 21 day5 22 day6 23 day7 24 day8 25 day9 26 day10 27 day11 28 day12 29 day13 30 day14 31 day15 32 day16 33 day17 34 day18 35 day19 36 day20 37 day21 38 day22 39 day23 40 day24 41 day25 42 day26 43 day27 44 day28 45 day29 46 day30 47 day31	.0.61.1.13.1.5
wlcScheduleProfileStart This object specifies the start value. In case of a time event it must be a time in format 'hh:mm'. In case of a value event it must be a valid value for the specified 'VarName', to specify the compare v…	OctetStringr/w Constraints: range: 0-31	.0.61.1.13.1.6
wlcScheduleProfileEnd This object specifies the end value (time or value range). In case of a time event it must be a time in format 'hh:mm'. If this is not given, the event is active only at the time 'Start', and set back to …	OctetStringr/w Constraints: range: 0-31	.0.61.1.13.1.7
wlcScheduleProfileParameters This variable isn't in use right now.	OctetStringr/w Constraints: range: 0-255	.0.61.1.13.1.8

This table combines WTP with the local services profile.

wlcLocalServicesEntry row .0.61.1.14.1

Indexes

wlcLocalServicesIndex

Column	Syntax	OID
wlcLocalServicesIndex This variable contains the unique WTP index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.14.1.1
wlcLocalServicesAdminStatus Enable or delete the local services profile from the requested WTP	Enumerationr/w Enumerated Values: 1 enabled 32 delete	.0.61.1.14.1.2
wlcLocalServicesProfIndex This variable contains the unique RADIUS service profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.14.1.3

This table contains configuration profiles for 
local services (e.g. httpd, sshd) on the WTP.

wlcLocalServicesProfileEntry row .0.61.1.15.1

Indexes

wlcLocalServicesProfileIndex

Column	Syntax	OID
wlcLocalServicesProfileIndex Unique local services profile index	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.15.1.1
wlcLocalServicesProfileAdminStatus The administrative status of this entry. The entry can be enabled(1), disabled(2) or set to delete(32) and is therefore deleted. Default is enabled(1).	Enumerationr/w Enumerated Values: 1 enabled 2 disabled 32 delete	.0.61.1.15.1.2
wlcLocalServicesProfileName The name of the ServicesProfile entry.	OctetStringr/w Constraints: range: 0-63	.0.61.1.15.1.3
wlcLocalServicesProfilePort The port number.	Integer32r/w Constraints: range: -1-65535	.0.61.1.15.1.4
wlcLocalServicesProfilePortRange The port range.	Integer32r/w Constraints: range: 1-65536	.0.61.1.15.1.5
wlcLocalServicesProfileProtocol The protocol type of this entry.	Enumerationr/w Enumerated Values: 1 icmp 2 igmp 4 ip 6 tcp 17 udp 253 udptcp 254 any 256 dont-verify	.0.61.1.15.1.6

The wlcWlanIfTable contains all WLAN interfaces of each WTP 
with their configured profiles.

wlcWlanIfEntry row .0.61.1.16.1

Indexes

wlcWlanIfIndex

Column	Syntax	OID
wlcWlanIfIndex Unique index which is incremented for each new WLAN interface entry.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.1
wlcWlanIfWTPIndex The wlcWlanIfWTPIndex is the uniqe WTP index see wlcWTPIndex.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.2
wlcWlanIfWTPMacAddress wlcWlanIfWTPMacAddress is the first ethernet MAC address of the WTP.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.0.61.1.16.1.3
wlcWlanIfProfIndex The wlcWlanIfProfIndex is the configured WLAN interface profile. See wlcWlanIfProfileIndex.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.4
wlcWlanIfType The current WLAN physical interface type for the WTP off(1) interface disabled access-point(2) access point client(3) client mode default(4) the type of the corresponding wlcWlanIfProfile delete(32) delete	Enumerationr/w Enumerated Values: 1 off 2 access-point 3 client 7 default 32 delete	.0.61.1.16.1.5
wlcWlanIfChannel The physical channel.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.6
wlcWlanIfAutoSelectedChannel The auto selected channel.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.7
wlcWlanIfSecondaryChannel The wlcWlanIfSecondaryChannel describes if the secondary channel (40Mhz bandwidth) is below(1) or above(2) of the current selected channel.	Enumerationr/w Enumerated Values: 1 below 2 above 3 default	.0.61.1.16.1.8
wlcWlanIfAutoSecondaryChannel The wlcWlanIfAutoSecondaryChannel describes if the secondary channel (40Mhz bandwidth) is below(1) or above(2) of the auto selected channel.	Enumeration Enumerated Values: 1 below 2 above	.0.61.1.16.1.9
wlcWlanIfTxPower Transmitter output power in dBm.	dBmInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.10
wlcWlanIfClientScanState This attribute holds the foreground scanning status. Writing scanning(2) in idle state triggers a new foreground scan cycle. All entries for this client interface in the wlcScanResultsTable are removed. When the WLAN …	Enumerationr/w Enumerated Values: 1 idle 2 scanning 3 update	.0.61.1.16.1.11
wlcWlanIfClientIndex Index pointer to the wlcClientProfileTable.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.12
wlcWlanIfHWIndex Index pointer to the wlcWlanHWTable.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.13
wlcWlanIfRadioIndexWTP WLAN interface index on the WTP.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.16.1.14

This table contains WLAN interface profiles.

wlcWlanIfProfileEntry row .0.61.1.17.1

Indexes

wlcWlanIfProfileIndex

Column	Syntax	OID
wlcWlanIfProfileIndex Unique index of a WIFI interface profile.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.17.1.1
wlcWlanIfProfileName The name of the requested profile.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.0.61.1.17.1.2
wlcWlanIfProfileType The WLAN physical interface type: off(1) interface disabled access-point(2) access point client(3) client mode delete(32) delete	Enumerationr/w Enumerated Values: 1 off 2 access-point 3 client 32 delete	.0.61.1.17.1.3
wlcWlanIfProfileMode Mixed and compatibility modes between various 802.11 substandards.	Enumerationr/w Enumerated Values: 1 m802-11b 2 m802-11g 3 m802-11mixed 4 m802-11mixed-long 5 m802-11mixed-short 6 m802-11a 7 m802-11bgn 8 m802-11gn 10 m802-11n 11 m802-11an 12 m802-11abg 13 m802-11abgn 14 m802-11agn	.0.61.1.17.1.4
wlcWlanIfProfileSpeed The value defines the bitrate or the coding scheme to use for data frames. Default value auto(31) enables automatic rate adaption.	Enumerationr/w Enumerated Values: 1 s1mbit 2 s2mbit 3 s5mbit 4 s6mbit 5 s9mbit 6 s11mbit 7 s12mbit 8 s18mbit 9 s24mbit 10 s36mbit 11 s48mbit 12 s54mbit 13 sMCS0-HT 14 sMCS1-HT 15 sMCS2-HT 16 sMCS3-HT 17 sMCS4-HT 18 sMCS5-HT 19 sMCS6-HT 20 sMCS7-HT 21 sMCS8-HT 22 sMCS9-HT 23 sMCS10-HT 24 sMCS11-HT 25 sMCS12-HT 26 sMCS13-HT 27 sMCS14-HT 28 sMCS15-HT 31 auto 32 sMCS16-HT 33 sMCS17-HT 34 sMCS18-HT 35 sMCS19-HT 36 sMCS20-HT 37 sMCS21-HT 38 sMCS22-HT 39 sMCS23-HT	.0.61.1.17.1.5
wlcWlanIfProfileSkipChannels24GHz If a bit is set the according channel will be skipped from the channel scan list (channel 1-14 for 2.4 GHz). Default is to scan all channels (i.e. no bit is set).	Bitsr/w Enumerated Values: 0 channel-1 1 channel-2 2 channel-3 3 channel-4 4 channel-5 5 channel-6 6 channel-7 7 channel-8 8 channel-9 9 channel-10 10 channel-11 11 channel-12 12 channel-13 13 channel-14	.0.61.1.17.1.6
wlcWlanIfProfileSkipChannels5GHz If a bit is set the accordingly channel will be skipped from the channel scan list (channel 36-173 for 5 GHz). Default is to scan all channels (i.e. no bit is set).	Bitsr/w Enumerated Values: 0 channel-36 1 channel-40 2 channel-44 3 channel-48 4 channel-52 5 channel-56 6 channel-60 7 channel-64 8 channel-100 9 channel-104 10 channel-108 11 channel-112 12 channel-116 13 channel-120 14 channel-124 15 channel-128 16 channel-132 17 channel-136 18 channel-140 19 channel-149 20 channel-153 21 channel-157 23 channel-161 24 channel-165 25 channel-169 26 channel-173	.0.61.1.17.1.7
wlcWlanIfProfileRtsThreshold This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed, except as RTS/CTS is used as a cross modulation protection mechanism. An RTS/CTS handshake shall be…	Integer32r/w Constraints: range: 1-2347	.0.61.1.17.1.8
wlcWlanIfProfileFragmentationThreshold This attribute shall specify the current maximum size, in octets, of the PSDU that may be delivered to the PHY. This maximum size does not apply in the case of A-MPDU. An MSDU, A-MSDU or MMPDU shall be broken into fragm…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.17.1.9
wlcWlanIfProfileBurst Sending wireless frames without backoff time.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.0.61.1.17.1.10
wlcWlanIfProfileCountry This attribute identifies the country in which the station is operating. The first two octets of this string are the two character country code as described in document ISO/IEC 3166-1. The third octet shall be one of th…	OctetStringr/w Constraints: range: 0-3	.0.61.1.17.1.11
wlcWlanIfProfileBand Frequency band. 'b24-GHz' -> 2.4 GHz band, 'b5-GHz' -> 5 GHz band, 'b58-GHz' -> 5.8 GHz band, 'b24-5-GHz' -> 2.4 GHz and 5 GHz band.	Enumerationr/w Enumerated Values: 1 b24-GHz 2 b5-GHz 3 b58-GHz 4 b24-5-GHz	.0.61.1.17.1.12
wlcWlanIfProfileAckWindow Additional 802.11 ACK timeout in microseconds. This must be set to non-zero value for radio distances larger than about 700m. Recommended setting is about 10 microseconds per kilometer.	millisecondsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.17.1.13
wlcWlanIfProfileBeaconPeriod This attribute contains the number of TU that this BSS uses for scheduling Beacon transmissions.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.17.1.14
wlcWlanIfProfileDTIMPeriod The number of DTIM intervals between the start of CFPs for this BSS.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.17.1.15
wlcWlanIfProfileSpatialStreams This attribute indicates the maximum number of spatial streams enabled. The default value of this attribute is 3.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.17.1.16
wlcWlanIfProfileGreenfield This attribute, when TRUE, indicates that the HT Greenfield option is enabled. The default value of this attribute is FALSE.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.17.1.17
wlcWlanIfProfileShortGI This attribute, when TRUE, indicates that the Short Guard option is enabled for 40 MHz operation. The default value of this attribute is FALSE.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.17.1.18
wlcWlanIfProfileRxSTBC This attribute, when TRUE, indicates that the entity's capability of receiving frames that are sent using the Space-Time Block Code (STBC) is enabled. The default value of this attribute is FALSE.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.17.1.19
wlcWlanIfProfileTxSTBC This attribute, when TRUE, indicates that the entity's capability of transmitting frames using Space-Time Block Code (STBC) option is enabled. The default value of this attribute is FALSE.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.17.1.20
wlcWlanIfProfileFortyMHzOperation This attribute, when TRUE, indicates that the 40 MHz Operation is enabled. The default value of this attribute is FALSE.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.17.1.21
wlcWlanIfProfileShortRetry This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to dot11RTSThreshold, that shall be made before a failure condition is indicated. The defau…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.17.1.22
wlcWlanIfProfileLongRetry This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than dot11RTSThreshold, that shall be made before a failure condition is indicated. The default value …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.17.1.23
wlcWlanIfProfileBgScanning Enable/disable background-scanning.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.0.61.1.17.1.24
wlcWlanIfProfileAirtimeFairness If AirtimeFairness is enabled(1), background or best-effort traffic sent from AP to STA is fairly scheduled among all stations associated to this radio profile, in respect of airtime usage. The default value of this att…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.0.61.1.17.1.25

This table contains WTP radio client profiles.

wlcClientProfileEntry row .0.61.1.18.1

Indexes

wlcClientProfileIndex

Column	Syntax	OID
wlcClientProfileIndex Unique Client profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.18.1.1
wlcClientProfileScanPeriodAMin Minimum time in ms to spend on a frequency when active scanning. Default is 10ms.	millisecondsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.18.1.2
wlcClientProfileScanPeriodAMax Maximum time in ms to spend on a frequency when active scanning. Default is 40ms.	millisecondsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.18.1.3
wlcClientProfileScanPeriodMin Minimum time in ms to spend on a frequency when passive scanning. Default is 20ms.	millisecondsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.18.1.4
wlcClientProfileScanPeriodMax Maximum time in ms to spend on a frequency when passive scanning. Default is 120ms.	millisecondsInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.18.1.5
wlcClientProfileAdminStatus Enable or delte the requested WLAN client profile.	Enumerationr/w Enumerated Values: 1 enabled 32 delete	.0.61.1.18.1.7

This table combines WTP with the VSS profile.

wlcVSSEntry row .0.61.1.19.1

Indexes

wlcVSSIndex

Column	Syntax	OID
wlcVSSIndex This variable contains a unique index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.19.1.1
wlcVSSwlanIfIndex This variable is the WLAN interface of the requested WTP WLAN interface.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.19.1.2
wlcVSSProfIndex This variable contains the unique VSS profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.19.1.3
wlcVSSAdminStatus Enable or delete the VSS profile from the requested WTP.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled 3 default 32 delete	.0.61.1.19.1.4

This table contains different 
VSS setting profiles.

wlcVSSProfileEntry row .0.61.1.20.1

Indexes

wlcVSSProfileIndex

Column	Syntax	OID
wlcVSSProfileIndex Unique VSS profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.20.1.1
wlcVSSProfileId This attribute reflects the Service Set ID used in the DesiredSSID parameter of the most recent MLME scan request.	OctetStringr/w Constraints: range: 0-32	.0.61.1.20.1.2
wlcVSSProfileName The VSS profile name.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.0.61.1.20.1.3
wlcVSSProfileAdminStatus Enable, disable or delete the requested VSS profile.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled 32 delete	.0.61.1.20.1.4
wlcVSSProfileSecurity The Security Option which will be used. wep40 and wep104:= WEP-Authentication wpa-psk := WPA-Authentication with PSK wpa := WPA-Authentication with radius (802.1X) wpa2 := OBSOLETE and not used anymore!	Enumerationr/w Enumerated Values: 1 none 2 wep40 3 wep104 4 wpa-psk 5 wpa 6 wpa2	.0.61.1.20.1.5
wlcVSSProfileDefaultKey Default key for WEP encryption.	Enumerationr/w Enumerated Values: 1 key1 2 key2 3 key3 4 key4	.0.61.1.20.1.6
wlcVSSProfileKey1 Key string for WEP key no. 1. Also used for WPA passphrase.	OctetStringr/w Constraints: range: 0-64	.0.61.1.20.1.7
wlcVSSProfileKey2 Key string for WEP key no. 2.	OctetStringr/w Constraints: range: 0-64	.0.61.1.20.1.8
wlcVSSProfileKey3 Key string for WEP key no. 3.	OctetStringr/w Constraints: range: 0-64	.0.61.1.20.1.9
wlcVSSProfileKey4 Key string for WEP key no. 4.	OctetStringr/w Constraints: range: 0-64	.0.61.1.20.1.10
wlcVSSProfileTotal The number of allowed clients of the requested VSS.	Integer32r/w Constraints: range: 1-256	.0.61.1.20.1.11
wlcVSSProfileMAC MAC Media Access Control via MAC Address.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.20.1.12
wlcVSSProfileLocal Routing between connected Clients.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.20.1.13
wlcVSSProfileHidden Define whether SSID is hidden (true) or not (false). Default value is false.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.20.1.14
wlcVSSProfileWPAUnicastCipher The set of unicast ciphers used for WPA.	Bitsr/w Enumerated Values: 1 tkip 2 aes	.0.61.1.20.1.15
wlcVSSProfileRSNUnicastCipher The set of unicast ciphers used for RSN.	Bitsr/w Enumerated Values: 1 tkip 2 aes	.0.61.1.20.1.16
wlcVSSProfileWpaMixedMode Allows mixed operation of WPA and WPA2 by value wpaandwpa2(3) (default value). For tightened security, value wpa2(2) can be selected. The value wpa(1) is available for some older clients with drivers that are unable to …	Enumerationr/w Enumerated Values: 1 wpa 2 wpa2 3 wpaandwpa2	.0.61.1.20.1.17
wlcVSSProfileRsnPreauthentication When this object is set to TRUE, this shall indicate that RSNA preauthentication is enabled on this entity. This object requires that dot11RSNAEnabled also be set to TRUE.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.20.1.18
wlcVSSProfileWMM This object defines whether WMM (Wi-Fi Multimedia) is active for this service set. Depending on the WLAN hardware and driver, WMM might only be allowed for one service set, i.e. enabling WMM for one service set disa…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.20.1.19
wlcVSSProfileARPProcessing This object defines whether ARP processing is active for this service set or not. ARP processing is a feature to reduce the number of ARP broadcast packets. If the AP finds the requested IP address in the node table …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.20.1.20
wlcVSSProfileVlanId The VLAN-Tag-Id used for the virtual interface.	Integer32r/w Constraints: range: 0-4095	.0.61.1.20.1.21
wlcVSSProfileSoftTotal If wlcVSSProfileSoftTotal STAs are connected to this VSS, subsequent association attempts will be rejected with BUSY. If a STA still tries to associate within 30sec, the association request will be accepted.	Integer32r/w Constraints: range: 1-256	.0.61.1.20.1.22
wlcVSSProfileBandSteeringPreference Define the preferred band for Band Steering. none : no preference (default) b24-GHz: prefer 2,4 GHz b5-GHz : prefer 5 GHz	Enumerationr/w Enumerated Values: 1 none 2 bs-24GHz 3 bs-5GHz	.0.61.1.20.1.23
wlcVSSProfileBlacklist Enable or disable blacklisting via MAC addresses.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.0.61.1.20.1.24
wlcVSSProfileUAPSD Enable or disable UAPSD	Enumerationr/w Enumerated Values: 1 enable 2 disable	.0.61.1.20.1.25
wlcVSSProfileStaRxShaping STA to AP bandwidth limitation per associated station. The value is given in bits per seconds, -1 is unlimited (default)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.20.1.26
wlcVSSProfileStaTxShaping AP to STA bandwidth limitation per associated station. The value is given in bits per seconds, -1 is unlimited (default)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.20.1.27

This table contains different ACL profiles.
The WLAN Access List is based on MAC Addresses.

wlcACLProfileEntry row .0.61.1.21.1

Indexes

wlcACLProfileIndex wlcACLProfileAddress

Column	Syntax	OID
wlcACLProfileIndex The variable is the unique profile index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.61.1.21.1.1
wlcACLProfileAddress The MAC Address for the accepted client.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.0.61.1.21.1.2
wlcACLProfileAdminStatus Enable, disable or delete the requested ACL profile entry.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled 32 delete	.0.61.1.21.1.3

The table contains different information of each WTP.

wlcWTPInfoEntry row .0.61.1.23.1

Indexes

wlcWTPInfoIndex

Column	Syntax	OID
wlcWTPInfoIndex Unique WTP information index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.23.1.1
wlcWTPInfoWTPIndex Unique WTP index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.23.1.2
wlcWTPInfoMacAddress The first ethernet MAC address of the WTPs.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.0.61.1.23.1.3
wlcWTPInfoState Reflects the current (CAPWAP) state of the WTP. idle(1) - WTP is idle (isn't seen by AC) discovery(2) - WTP is discovered by AC authorize(3) - WTP is waiting to be authorized by AC join(4) - WTP send join request to AC…	Enumeration Enumerated Values: 1 idle 2 discovery 3 authorize 4 join 5 configure 6 mib-configure 7 data-check 8 run 9 reset 10 lostac	.0.61.1.23.1.4
wlcWTPInfoDevice The official WTP device name.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.0.61.1.23.1.5
wlcWTPInfoSerialNo The unique serial number of the WTP	OctetString Constraints: range: 0-64	.0.61.1.23.1.6
wlcWTPInfoSwVer Current software version of the WTP	OctetString Constraints: range: 0-32	.0.61.1.23.1.7
wlcWTPInfoInetAddressType The IP address type of the WTP. It is one of: -unknown(0): an unknown address type -ipv4(1) : an IPv4 address -ipv6(2) : an IPv6 address -ipv4z(3) : a non-global IPv4 address including a zone …	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.0.61.1.23.1.8
wlcWTPInfoInetAddress IP address of the requested WTP.	RFC1155-SMIIpAddress Type Constraints: range: 4	.0.61.1.23.1.9
wlcWTPInfoNoRadios Number of radios that the device has.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.23.1.10
wlcWTPInfoConnectTime This attribute records the time since last state change.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.0.61.1.23.1.11
wlcWTPInfoTxPackets The transmitted packets of the requested WTP.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.23.1.12
wlcWTPInfoTxBytes Number of transmitted bytes of the requested WTP.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.23.1.13
wlcWTPInfoRxPackets Number of received packets of the requested WTP.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.23.1.14
wlcWTPInfoRxBytes Number of received bytes of the requested WTP.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.23.1.15
wlcWTPInfoRetransmissions Number of retransmissions of the requested WTP.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.23.1.16
wlcWTPInfoLastSeen On Ac this is the timestamp of the last receved CAPWAP UDP packet from that WTP. On WTP this is the timestamp of the last received CAPWAP UDP packet from AC.		.0.61.1.23.1.17

This table lists all features of supported wireless cards.

wlcWlanHWEntry row .0.61.1.24.1

Indexes

wlcWlanHWIndex

Column	Syntax	OID
wlcWlanHWIndex Unique WLAN hardware index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.24.1.1
wlcWlanHWName Name of the WLAN hardware.	OctetString Constraints: range: 0-32	.0.61.1.24.1.2
wlcWlanHWTxPowerSteps The steps of the TX power the wireless card supports.	OctetString Constraints: range: 0-64	.0.61.1.24.1.3
wlcWlanHWShortRetries This variable says if the wireless card supports the configuration of the short retry value or not. Default is false.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.24.1.4
wlcWlanHWLongRetries This variable says if the wireless card supports the configuration of the long retry value or not. Default is false.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.24.1.5
wlcWlanHWFragmentationThreshold This variable says if the wireless card supports the configuration of the fragmentation threshold value or not.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.24.1.6
wlcWlanHWNoSpatialRx This attribute indicates the number of receivable spatial streams.	Integer32 Constraints: range: 1-8	.0.61.1.24.1.7
wlcWlanHWNoSpatialTx This attribute indicates the maximum of transmittable spatial streams.	Integer32 Constraints: range: 1-8	.0.61.1.24.1.8
wlcWlanHWBands The supported WLAN bands.	Bits Enumerated Values: 0 band24 1 band5 2 band58	.0.61.1.24.1.9
wlcWlanHWModes The Supported WLAN modes.	Bits Enumerated Values: 0 m802-11a 1 m802-11b 2 m802-11g 3 m802-11n	.0.61.1.24.1.10
wlcWlanHWBandwidth The supported bandwidth capabilities of the radio. In case of false only 20MHz bandwidth is supported. In case of true also 40MHz bandwidth is supported.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.24.1.11
wlcWlanHWShortGI This attribute, when TRUE, indicates that the Short Guard option is implemented. The default value of this attribute is FALSE.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.24.1.12
wlcWlanHWGreenfield This attribute, when TRUE, indicates that the HT Greenfield option is implemented. The default value of this attribute is FALSE.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.24.1.13
wlcWlanHWRxSTBC This attribute, when TRUE, indicates that the entity is capable of receiving frames that are sent using the Space-Time Block Code (STBC). The default value of this attribute is FALSE.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.24.1.14
wlcWlanHWTxSTBC This attribute, when TRUE, indicates that the entity is capable of transmitting frames using Space-Time Block Code (STBC) option. The default value of this attribute is FALSE.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.24.1.15
wlcWlanHWSkipModes This variable says which modes of the WlanIfSkipChannels the wireless card supports.	Bits Enumerated Values: 0 ap24ghz 1 ap5ghz 2 client24ghz 3 client5ghz	.0.61.1.24.1.16

This table contains the current settings and statistics of each
WLAN interface.

wlcWlanIfStatEntry row .0.61.1.25.1

Indexes

wlcWlanIfStatIndex

Column	Syntax	OID
wlcWlanIfStatIndex Uniqe WLAN interface statistic index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.25.1.1
wlcWlanIfStatChannel Current selected channel of the requested WLAN interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.25.1.2
wlcWlanIfStatSecondaryChannel Current secondary channel of the requested WLAN interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.25.1.3
wlcWlanIfStatAddress The MAC address of the requested WLAN interface.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.0.61.1.25.1.4
wlcWlanIfStatType The type which is setup for the requested WLAN interface.	Enumeration Enumerated Values: 1 off 2 access-point 3 client 32 delete	.0.61.1.25.1.5
wlcWlanIfStatBand The current operation band of the requested WLAN interface.	Enumeration Enumerated Values: 1 b24-GHz 2 b5-GHz 3 b58-GHz 4 b24-5-GHz	.0.61.1.25.1.6
wlcWlanIfStatMode The current operation mode of the requested WLAN interface.	Enumeration Enumerated Values: 1 m802-11b 2 m802-11g 3 m802-11mixed 4 m802-11mixed-long 5 m802-11mixed-short 6 m802-11a 7 m802-11bgn 8 m802-11gn 10 m802-11n 11 m802-11an 12 m802-11abg 13 m802-11abgn 14 m802-11agn	.0.61.1.25.1.7
wlcWlanIfStatTxPower The current transmit power of the requested WLAN interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.25.1.8
wlcWlanIfStatFortyMHzOperation This variable is TRUE if the requested WLAN interface currently operates with 40MHz bandwidth.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.25.1.9
wlcWlanIfStatShortGI This variable is TRUE if the short guard interval is currently enabled on the requested WLAN interface.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.25.1.10
wlcWlanIfStatNoSpatialEnabled Number of enabled spatial stream on the requested WLAN interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.25.1.11
wlcWlanIfStatGreenfield This variable is TRUE if the green field option is currently enabled on the requested WLAN interface.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.25.1.12
wlcWlanIfStatTxPackets Number of transmitted packets.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.25.1.13
wlcWlanIfStatTxBytes Number of transmitted bytes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.25.1.14
wlcWlanIfStatTxDropped Number of dropped packets in transmit direction.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.25.1.15
wlcWlanIfStatRxPackets Number of received packets.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.25.1.16
wlcWlanIfStatRxBytes Number of received bytes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.25.1.17
wlcWlanIfStatRxErrors This variable is counting packets that were not received correctly.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.25.1.18
wlcWlanIfStatAssociated Number of currently associated clients.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.25.1.19
wlcWlanIfStatOperState This attribute reflects the operational state of the corresponding WLAN card. 'true' -> radio is enabled, 'false' -> radio is disabled.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.25.1.20

This table contains statistic information about each VSS.

wlcVSSStatEntry row .0.61.1.26.1

Indexes

wlcVSSStatVSSIndex

Column	Syntax	OID
wlcVSSStatVSSIndex The unique VSS index.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.26.1.1
wlcVSSStatCurrent Number of currently associated stations.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.26.1.2
wlcVSSStatBytesTx Transmitted Bytes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.26.1.3
wlcVSSStatBytesRx Received Bytes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.61.1.26.1.4
wlcVSSStatBSSID This object contains the current BSSID for the service set.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.0.61.1.26.1.5
wlcVSSStatOperState This object contains the current OperState for the service set.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.61.1.26.1.6
wlcVSSStatSoftTotalDenied Number of rejected clients due to wlcVSSProfileSoftTotal limit.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.26.1.7
wlcVSSStatBSMovements Number of clients moved to other band by band steering mechanism.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.26.1.8
wlcVSSStatClearCounter counting := accounting is active, clearing := clear all statistics	Enumerationr/w Enumerated Values: 1 counting 2 clearing	.0.61.1.26.1.9
wlcVSSStatTotalDenied Number of rejected clients due to wlcVSSProfileTotal limit.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.26.1.10

This table contains the list of BSS entries found by foreground 
or background scanning.

wlcScanResultsEntry row .0.61.1.27.1

Indexes

wlcScanResultsIndex wlcScanResultswlanIfIndex

Column	Syntax	OID
wlcScanResultsIndex Auxiliary index for different BSS entries.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.27.1.1
wlcScanResultswlanIfIndex Index of WLAN Interface the scan results belong to.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.27.1.2
wlcScanResultsBSSID BSSID of this BSS.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.0.61.1.27.1.3
wlcScanResultsRSSI Receive signal strength of this BSS.	WlanRSSI Type Constraints: range: -110..0	.0.61.1.27.1.4
wlcScanResultsSSID SSID aka network name of this BSS. If broadcasting of SSID is disabled on this BSS, this string may be empty.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.0.61.1.27.1.5
wlcScanResultsChannel The channel this BSS was received on.	Integer32 Type Constraints: range: -2147483648..2147483647	.0.61.1.27.1.6
wlcScanResultsPrivacy This attribute contains the privacy type of the scanned device.	Enumeration Enumerated Values: 1 none 2 wep 3 wpa-psk 4 wpaandwpa2-psk 5 wpa2-psk 6 wpa-enterprise 7 wpaandwpa2-enterprise 8 wpa2-enterprise	.0.61.1.27.1.7
wlcScanResultsType This attribute contains the device type of the scanned device.	Enumeration Enumerated Values: 1 access-point 2 ad-hoc	.0.61.1.27.1.8
wlcScanResultsWPAUnicastCipher This attribute contains the WPA unicast ciphers of the scanned device.	Bits Enumerated Values: 0 cipher-none 1 cipher-wep40 2 cipher-wep104 3 cipher-tkip 4 cipher-aes	.0.61.1.27.1.9
wlcScanResultsRSNUnicastCipher This attribute contains the RSN unicast ciphers of the scanned device.	Bits Enumerated Values: 0 cipher-none 1 cipher-wep40 2 cipher-wep104 3 cipher-tkip 4 cipher-aes	.0.61.1.27.1.10
wlcScanResultsAPType This attribute contains the type of the scanned access point. 'own' -> managed AP, 'neighborhood' -> neighborhood AP 'rogue' -> foreign AP but with one of our SSIDs, 'own-manipulated' -> managed AP but with manipulated…	Enumeration Enumerated Values: 1 own 2 neighborhood 3 rogue 4 own-manipulated 5 knownneighbor 6 knownrogue	.0.61.1.27.1.11
wlcScanResultsLastSeen This attribute contains that time when an access point or client was seen for the last time.		.0.61.1.27.1.12