APPLIC-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
30
Rows
30
Columns
249
.1.3.6.1.4.1.81.19.1.1
·
1 row entry
·
25 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lseGroupTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lseGroupTable'
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lseGroupIdmandatory
Slot number in which the group is installed.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.1.1.1.1 |
|
lseGroupFastOpenmandatory
Setting the value of this attribute to ON activates the port for short idle time
when code violation was detected. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.2 |
|
lseGroup10MSqltmandatory
Setting the value of this attribute to ON activates the mechanism of detection
preamble of 10Mhz. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.3 |
|
lseGroupSmartSqltobsolete
Control the mechnism of the input sensitivity of the port.
|
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.4 |
|
lseGroupCParametermandatory
Defines the number of consecutive collisions the port waits before it ceases transmitting
of 512 bits time toward the station. |
Integer32r/w | .1.3.6.1.4.1.81.19.1.1.1.5 |
|
lseGroupIPGJamLengthmandatory
Defines the IPG jam length in Ethernet bit time (100nS) start at 16 bit time in
steps of 16, to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values are from 48 bit times (480nano-seconds) in step of 4, … |
Integer32r/w | .1.3.6.1.4.1.81.19.1.1.1.6 |
|
lseGroupJamLengthmandatory
Defines the Jam Length in time starting from 8 (800micro-seconds) to
120 (12mili-seconds). Each step of 8 is equal 800micro-seconds. For LFE-100, values are from 8 (80micro-seconds) to 32 (320micro-seconds), each step… |
Integer32r/w | .1.3.6.1.4.1.81.19.1.1.1.7 |
|
lseGroupDataBlinderLengthmandatory
Defines the Data Blinder Length in Ethernet bit time (100nS) start at 16 bit time in steps of
16 to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values are from 0 bit times in step of 4, to 124 (1240na… |
Integer32r/w | .1.3.6.1.4.1.81.19.1.1.1.8 |
|
lseGroupIPGDataLengthmandatory
Defines the IPG (Inter Packet Gap) length in Ethernet bit time
(100nS) starting at 16 bit time in steps of 16 to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values are from 48 bit times (480nano-seconds… |
Integer32r/w | .1.3.6.1.4.1.81.19.1.1.1.9 |
|
lseGroupActiveMonitormandatory
This attribute defines the module which is the high-speed bus active monitor.
|
Enumeration | .1.3.6.1.4.1.81.19.1.1.1.10 |
|
lseGroupBackbone12mandatory
Port 1 and 2 in the board perform as Backbone link.
lse208 - upper cluster is RX only and lower cluster is TX only. lse404 - upper port is Rx only and second port is Tx only. Two remains port are performed as regular fo… |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.11 |
|
lseGroupSetDefaultsmandatory
Set all hardware parameters to their default values. This item will
always return a value of off(2), since it acts like a toggle switch. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.12 |
|
lseGroupBackbone34mandatory
Port 3 and 4 in the board performed as Backbone link.
lse404 - Third port is Rx only and forth port is Tx only. Two remaining ports performed as regular foirl interfaces. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.13 |
|
lseGroupBackboneRedun12mandatory
Value on(1) of this attribute defines a redundancy (backup)
relationship between Backbone port 1 and backbone port 2 on a LANswiltch module. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.14 |
|
lseGroupBackoffFromJammandatory
Value on(1) of this attribute defines non-consecutive
jam after a collision has occured in LANswitch modules. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.15 |
|
lseGroupCAMClearmandatory
Value on(1) of this attribute causes the LANSwitch
module to clear the CAM tables. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.16 |
|
lseGroupJamPreventmandatory
Jam prevent flag.
Functionaly, Jam prevent is a back-pressure into the line direction. There are two modes of opration: 1) automatic - the sensor gets the items status from HW 2) manual - the sensor gets the items … |
Enumerationr/w Constraints: range: 1-4 |
.1.3.6.1.4.1.81.19.1.1.1.17 |
|
lseGroupNormOpClmandatory
Normaly Open/Close flag.
When open(1) state is set, the sensor should activate a delay mechanism for the module to operate at Normaly-Closed mode for 30 seconds in order to enable the port's CAM to learn the current seg… |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.18 |
|
lseGroupNormOpDelaymandatory
When sets to a value greater than 0 (zero) and the MIB item
lseGroupNormOpCl is equal to closed(2), this item define the time delay that the module will remain in normally open mode before it will move to normaly clos… |
Integer32r/w | .1.3.6.1.4.1.81.19.1.1.1.19 |
|
lseGroupAutoPartitionEnablemandatory
Enables autopartition mechanism support in the group level for each port of the group.
|
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.20 |
|
lseGroupWorkStatemandatory
One of the possible states of the module: this item
indicates if the module is runing or booting. The value runAndBoot(3) indicates a serious software problem. |
Enumeration | .1.3.6.1.4.1.81.19.1.1.1.21 |
|
lseGroupBITResultmandatory
The Bit Indication Test in state 'faulty' indicates a problem.
The agent should send a fault trap in this case. |
Enumeration | .1.3.6.1.4.1.81.19.1.1.1.22 |
|
lseGroupAssignSlotsmandatory
In a multi-backbone configuration within a single HUB, this item enables to assign
backbone module with specific slot numbers. Only packets from these slots should be handled by the backbone module, Packets from other… |
OctetStringr/w | .1.3.6.1.4.1.81.19.1.1.1.23 |
|
lseGroupHSBMonStatusmandatory
This is a bit-masked attribute which displays events which may cause HSB Reset.
When a bit is '1', the relevant evet may cause HSB Reset. When a bit is '0', the relevant evet will not cause HSB Reset. The following are … |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.1.1.1.24 |
|
lseGroupEnableHSBResetmandatory
This item enables/disables the HSB Reset mechanism in the module.
|
Enumerationr/w | .1.3.6.1.4.1.81.19.1.1.1.25 |
.1.3.6.1.4.1.81.19.1.2.1
·
1 row entry
·
46 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lseIntPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lseIntPortTable'
An entry in the table, containing data about a single internal LanSwitch bank.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lseIntPortGroupIdmandatory
Id of the group to which the port belongs.
|
Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.1 |
|
lseIntPortIdmandatory
Number of LanSwitch port in the board.
|
Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.2 |
|
lseIntPortIOModemandatory
on(1) activates IO mode in which all packets on the
high-speed bus that were not captured by any regular port are captured by the I/O port. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.3 |
|
lseIntPortResetSwitchCAMmandatory
Acting like toggle switch thus always returns off(2)
on read. When set to on(1), causes the reset of the LANswitch CAM (addresses) memory. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.4 |
|
lseIntPortVideoPacketmandatory
When set to on(1), all Tx packets toward the
high-speed bus to video type packets. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.5 |
|
lseIntPortPriorityStateMachinemandatory
Setting the value of this attribute to on(1) activates
the priority mechanism. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.6 |
|
lseIntPortActiveBroadcastPrioritymandatory
Setting the value of this attribute to on(1) activates
the active broadcast mode in priority mechanism. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.7 |
|
lseIntPortPriorityLevelmandatory
This attribute defines the priority levels of
Tx packets toward the high-speed bus. The highest priority is broadcast(1). |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.8 |
|
lseIntPortSuperPriorityEnablemandatory
When limited space is left in Tx buffer, only the highest priority
packets are accepted. This in turn can create a situation in which one port tries to send a packet and never gets its chance to be accepted. In or… |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.9 |
|
lseIntPortRoutingModemandatory
generic(1) - examines all the packets that are
not members of any virtual network. net(2) - examines only the packets that have the port's network number. allPackets(4) - examine all packets regardless of their routin… |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.10 |
|
lseIntPortGlobalmandatory
Setting the global mode to on(1) sets the
port in a network routing mode that examines all packets that are not members of all virtual networks. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.11 |
|
lseIntPortLearnIOCAMmandatory
Setting this parameter to on(1) enables an I/O port to
learn incoming MAC addresses received in its port and store them in its CAM. Packets with destination address that match the CAM addresses are not transferred to t… |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.12 |
|
lseIntPortSecuritymandatory
Setting the value of this attribute to on(1) activates the security mode.
|
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.13 |
|
lseIntPortIgnoreBusymandatory
Setting the value of this attribute to on(1) activates the ignore busy mode.
The busy signal toward the high-speed bus is not activated even though the TX buffer is full. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.14 |
|
lseIntPortRetryPriorityLevel1mandatory
The port increases the priority level of the high-speed bus packets after the defined number
(0..31) trials. |
Integer32r/w | .1.3.6.1.4.1.81.19.1.2.1.1.15 |
|
lseIntPortRetryPriorityLevel2mandatory
The port increases the priority level of the high-speed bus packets after the defined number
(0..255) trials. |
Integer32r/w | .1.3.6.1.4.1.81.19.1.2.1.1.16 |
|
lseIntPortRetryPriorityLevel3mandatory
The port increases the priority level of the high-speed bus packets after the defined number
(0..255) trials. |
Integer32r/w | .1.3.6.1.4.1.81.19.1.2.1.1.17 |
|
lseIntPortIgnoreProtocolTypemandatory
Any packet regardless of the protocol type is received from the high-speed bus.
|
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.18 |
|
lseIntPortCompanyMACmandatory
The attribute defines the first three bytes of the MAC address of the video host server.
|
OctetStringr/w | .1.3.6.1.4.1.81.19.1.2.1.1.19 |
|
lseIntPortTxSafetyZonemandatory
Defines the Tx Safety Zone in bits.
|
Integer32r/w | .1.3.6.1.4.1.81.19.1.2.1.1.20 |
|
lseIntPortRxSafetyZonemandatory
Defines the Rx Safety Zone in bits.
|
Integer32r/w | .1.3.6.1.4.1.81.19.1.2.1.1.21 |
|
lseIntPortTxBurstLengthmandatory
Defines the TX Burst Length in bits.
|
Integer32r/w Constraints: range: 1-65535 |
.1.3.6.1.4.1.81.19.1.2.1.1.22 |
|
lseIntPortSecurityIntrudermandatory
The value on(1) of this attribute reflects a security violation occurrence.
|
Enumeration Constraints: range: 1-65535 |
.1.3.6.1.4.1.81.19.1.2.1.1.23 |
|
lseIntPortJabbermandatory
Value on(1) of this attribute reflects that jabber was transmitted
to the port by the high-speed bus. |
Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.24 |
|
lseIntPortCAMmandatory
112 bytes of MAC addresses. Each contains one
byte of the port number and six bytes of the MAC address. This enables to send 16 MAC Addresses ( 16*7=112 bytes) |
OctetStringr/w | .1.3.6.1.4.1.81.19.1.2.1.1.25 |
|
lseIntPortVideoStateMachinemandatory
Setting the value of this attribute to on(1) activates the video state machine mode.
Received packets are filtered by demand from the station. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.26 |
|
lseIntPortTransmitWeightmandatory
Defines the Transmit Weight of the frames for the current LANswitch port toward
the high - speed bus. |
Integer32r/w | .1.3.6.1.4.1.81.19.1.2.1.1.27 |
|
lseIntPortSuperPrioritymandatory
Setting the value of this attribute to on(1) activates the retry priority functions.
|
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.28 |
|
lseIntPortAlignmentmandatory
The number of alignment errors observed on a specified port.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.1.2.1.1.29 |
|
lseIntPortRxRejectobsolete
The number of Rx buffer full observed on a specified port, from the line toward the
High-speed bus. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.1.2.1.1.30 |
|
lseIntPortTxRejectobsolete
The number of Tx buffer full observed on a specified port, from the line toward the
High-speed bus. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.1.2.1.1.31 |
|
lseIntPortRxEmpty0mandatory
Define the highest threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is full. When the buffer reached this threshold, all packets will be rejected. Version 7.0 |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.1.2.1.1.32 |
|
lseIntPortRxEmpty1mandatory
Define the middle threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is almost full. When the buffer reached this threshold, the only packets that the port will receive will be… |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.1.2.1.1.33 |
|
lseIntPortRxEmpty2mandatory
Define the lowest threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is almost full. When the buffer reached this threshold, the only packets that the port will receive will be… |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.1.2.1.1.34 |
|
lseIntPortSuperNetNumbermandatory
If the internal port supports SuperNet mode, the user
have to define the supernet number. Default value is 0. Change of this number when the internal port is Generic, Global or Global SuperNet must be blocked by the s… |
Integer32r/w | .1.3.6.1.4.1.81.19.1.2.1.1.35 |
|
lseIntPortGlobalSuperNetmandatory
An internal port that is part of all SuperNets is set to
Global SuperNet routing. The SuperNet number is 15 in this case. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.36 |
|
lseIntPortMACAddressmandatory
The MAC address of the port, if it has. If not, an octet
string of length 0. |
OctetString | .1.3.6.1.4.1.81.19.1.2.1.1.37 |
|
lseIntPortIgnoreRoutingModemandatory
When this parameter is 'ignore', the LANSwitch
port monitors all packets without paying attention to the virtual net assignment. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.38 |
|
lseIntPortCAMLastChangemandatory
This attribute contains the value of sysUpTime
at the time any change occured to the content of the specific CAM. |
RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.1.2.1.1.39 |
|
lseIntPortCopiedPortmandatory
The port monitored on the LANswitch bus by the
LSE-PM module. The value of this item is: 32*(S-1)+P, where S is the slot number in the hub and P the port within the slot (1.. 32). When the value of this item is 0, th… |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.1.2.1.1.40 |
|
lseIntPortBroadcastBehaviormandatory
This item relates only to LSE-PM modules. The value of
this item defines the method by which the module treats broadcast and multicast packets. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.41 |
|
lseIntPortFilteringMethodmandatory
This item is relevant only to the LSE-PM module.
The value of this item defines the filtering method used to capture packets from the Cellenium bus to the Ethernet connection. |
Enumerationr/w Constraints: range: 1-65535 |
.1.3.6.1.4.1.81.19.1.2.1.1.42 |
|
lseIntPortSetFiltermandatory
This item is relevant only to the LSE-PM module.
The item is used to add new addresses to the module's filtering table. The string is a sequence of MAC addresses, 6 bytes each. When the item is set, each address in th… |
OctetStringr/w Constraints: range: 1-65535 |
.1.3.6.1.4.1.81.19.1.2.1.1.43 |
|
lseIntPortRemoveFiltermandatory
This item is relevant only to the LSE-PM module.
The item is used to remove existing addresses from the module's filtering table. The string is a sequence of MAC addresses, 6 bytes each. When the item is set, all ad… |
OctetStringr/w | .1.3.6.1.4.1.81.19.1.2.1.1.44 |
|
lseIntPortClearFiltermandatory
This item is relevant only to the LSE-PM module.
The item acts as a toggle switch: when its value is set to clear(2), the contents of the module's filtering tables are cleared. This item always returns an empty string… |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.2.1.1.45 |
|
lseIntPortMonitorMissedEventsmandatory
This item is relevant only to LSE-PM modules. The value
of the counter is the number of packets that were not captured by the port as a result of overload on the Ethernet line, though the port's filter was configured… |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.1.2.1.1.46 |
.1.3.6.1.4.1.81.19.1.2.2.1
·
1 row entry
·
4 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lseIntPortMACAddTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lseIntPortMACAddTable'
An entry in the table containing data about a single internal switch port.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lseIntPortMACAddGroupIdmandatory
Id of the group to which the port belongs.
|
Integer32 | .1.3.6.1.4.1.81.19.1.2.2.1.1.1 |
|
lseIntPortMACAddPortIdmandatory
The LANswitch port number in the board.
|
Integer32 | .1.3.6.1.4.1.81.19.1.2.2.1.1.2 |
|
lseIntPortMACAddLAIdmandatory
The lower 2 bytes of the Last MAC Address on the previous
list. Use the 0 value to start from the beginning of the list. |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.1.2.2.1.1.3 |
|
lseIntPortMACAddListmandatory
This item contains MAC address (source addresses) of the port.
Each MAC address is 6 bytes long. The list is started with the MAC address that follows the lseIntPortMACAddLAId. |
OctetString | .1.3.6.1.4.1.81.19.1.2.2.1.1.4 |
.1.3.6.1.4.1.81.19.1.2.3.1
·
1 row entry
·
4 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lseIntPortFilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lseIntPortFilterTable'
This table is supported only for the LSE-PM module.
The table reports the contents of the port's filtering
mechanism.
The table reports the contents of the port's filtering
mechanism.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lseIntPortFilterGroupIdmandatory
This item is relevant only for the LSE-PM module. The
item defines the group to which the port belongs (i.e., the module number). |
Integer32 | .1.3.6.1.4.1.81.19.1.2.3.1.1.1 |
|
lseIntPortFilterPortIdmandatory
This item is relevant only for the LSE-PM module. The
item defines the number of the LANswitch port in the board. |
Integer32 | .1.3.6.1.4.1.81.19.1.2.3.1.1.2 |
|
lseIntPortFilterLAIdmandatory
This item is relevant only for the LSE-PM module. The
item contains the lower 2 bytes of the Last MAC Address on the previous list. Use the 0 value to start from the beginning of the list. |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.1.2.3.1.1.3 |
|
lseIntPortFilterListmandatory
This item is relevant only for the LSE-PM module. The
item contains the MAC addresses in the filter. Each MAC address is 6 bytes long. The list is started with the MAC address that follows the lseIntPortFilterLAId. |
OctetString | .1.3.6.1.4.1.81.19.1.2.3.1.1.4 |
.1.3.6.1.4.1.81.19.1.2.4
·
1 row entry
·
5 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lseIntPortMACVlanTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lseIntPortMACVlanTable'
This table extends the lseIntPortMACAddTable table with VLAN support providing mirrow of CAM content arranged by port and Vlan. The table supports the show cam commands for stack switch products.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lseIntPortMACVlanGroupIdmandatory
Id of the group to which the port belongs.
|
Integer32 | .1.3.6.1.4.1.81.19.1.2.4.1.1 |
|
lseIntPortMACVlanPortIdmandatory
The LANswitch port number in the board.
|
Integer32 | .1.3.6.1.4.1.81.19.1.2.4.1.2 |
|
lseIntPortMACVlanVlanmandatory
Id of the Vlan
|
Integer32 | .1.3.6.1.4.1.81.19.1.2.4.1.3 |
|
lseIntPortMACVlanLAIdmandatory
The lower 2 bytes of the Last MAC Address on the previous
list. Use the 0 value to start from the beginning of the list. |
Integer32 | .1.3.6.1.4.1.81.19.1.2.4.1.4 |
|
lseIntPortMACVlanMAClistmandatory
This item contains MAC address (source addresses) of the port.
Each MAC address is 6 bytes long. The list is started with the MAC address that follows the lseIntPortMACVlanLAId. |
OctetString | .1.3.6.1.4.1.81.19.1.2.4.1.5 |
.1.3.6.1.4.1.81.19.1.3.1
·
1 row entry
·
4 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsePortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsePortTable'
An entry in the table containing data about a single external switch port.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsePortGroupIdmandatory
Id of the group to which the port belongs.
|
Integer32 | .1.3.6.1.4.1.81.19.1.3.1.1.1 |
|
lsePortIdmandatory
Number of LanSwitch port in the board.
|
Integer32 Constraints: range: 0-100 |
.1.3.6.1.4.1.81.19.1.3.1.1.2 |
|
lsePortPolaritymandatory
Setting the value of this attribute to ON activates the automatic port polarity
detection mode. |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.3.1.1.3 |
|
lsePortBackboneStatusmandatory
It is the status of a single port that associated with a particular
Backbone port. It is utilized by the Agent in the Soft Redundancy algorithm between Backbone ports in LANswitch environment |
Enumerationr/w | .1.3.6.1.4.1.81.19.1.3.1.1.4 |
.1.3.6.1.4.1.81.19.2.1
·
1 row entry
·
3 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lhsGroupTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lhsGroupTable'
Table with group-related parameters.
Entry in the table.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lhsGroupIdmandatory
Unique slot identifier in which the module is located.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.2.1.1.1 |
|
lhsGroupMainSWVersionmandatory
Software version of the main CPU.
|
RFC1213-MIBDisplayString | .1.3.6.1.4.1.81.19.2.1.1.2 |
|
lhsGroupProtocolTypemandatory
This attribute set the protocol type in which the LHB is collecting from
the high-speed bus. |
Enumerationr/w Constraints: range: 0-100 |
.1.3.6.1.4.1.81.19.2.1.1.3 |
.1.3.6.1.4.1.81.19.2.2
·
1 row entry
·
15 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lhsPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lhsPortTable'
Table with port-related parameters.
Entry in the table.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lhsPortGroupIdmandatory
Slot index in which the module is located.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.2.2.1.1 |
|
lhsPortIdmandatory
Port number to which the data is related.
|
Integer32 Constraints: range: 0-100 |
.1.3.6.1.4.1.81.19.2.2.1.2 |
|
lhsTxUCastmandatory
Number of unicast packets transmitted.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.3 |
|
lhsTxBCastmandatory
Number of broadcast packets transmitted.
|
RFC1155-SMICounter Constraints: range: 0-100 |
.1.3.6.1.4.1.81.19.2.2.1.4 |
|
lhsTxMCastmandatory
Number of multicast packets transmitted.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.5 |
|
lhsTxUrunErrmandatory
Number of transmit packet underruns.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.6 |
|
lhsTxParErrmandatory
Number of transmit packet parity errors.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.7 |
|
lhsRxUCastmandatory
Number of unicast packets received.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.8 |
|
lhsRxBCastmandatory
Number of broadcast packets received.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.9 |
|
lhsRxMCastmandatory
Number of multicast packets received.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.10 |
|
lhsRxOrunErrmandatory
Number of receive overrun errors.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.11 |
|
lhsRxParErrmandatory
Number of receive parity errors.
|
RFC1155-SMICounter Constraints: range: 6-6 |
.1.3.6.1.4.1.81.19.2.2.1.12 |
|
lhsRxRscErrmandatory
Number of receive resource errors.
|
RFC1155-SMICounter Constraints: range: 6-6 |
.1.3.6.1.4.1.81.19.2.2.1.13 |
|
lhsRxBadTypeErrmandatory
Number of bad frame type packets received.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.2.2.1.14 |
|
lhsLinkStatusmandatory
This attribute describes the status of the optical link as detected
by the sensor software. |
Enumeration Constraints: range: 1-255 |
.1.3.6.1.4.1.81.19.2.2.1.15 |
.1.3.6.1.4.1.81.19.3.2.13
·
1 row entry
·
3 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsBusStatsPriorityTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsBusStatsPriorityTable'
A list of priority count entries.
A list of statistics related to a specific priority level on
the LANswitch bus.
the LANswitch bus.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsBusStatsPriorityIndexmandatory
The priority for which this entry reports statistics .
|
Integer32 | .1.3.6.1.4.1.81.19.3.2.13.1.1 |
|
lsBusStatsPriorityPktsmandatory
The total number of packets (including error packets)
received on the LANswitch bus whose priority is that defined for this entry. |
RFC1155-SMICounter Constraints: range: 0-7 |
.1.3.6.1.4.1.81.19.3.2.13.1.2 |
|
lsBusStatsPriorityOctetsmandatory
The total number of octets (including error packets)
received on the LANswitch bus whose packets have the priority defined for this entry. |
RFC1155-SMICounter Constraints: range: 0-7 |
.1.3.6.1.4.1.81.19.3.2.13.1.3 |
.1.3.6.1.4.1.81.19.3.2.15
·
1 row entry
·
3 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsBusStatsVirtualNetTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsBusStatsVirtualNetTable'
A list of virtual net statistics.
A list of staistics related to a specific virtual net which
exists on the LANswitch bus.
exists on the LANswitch bus.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsBusStatsVirtualNetmandatory
The virtual net for which this entry reports statistics .
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.3.2.15.1.1 |
|
lsBusStatsVirtualNetPacketsmandatory
The number of good packets that were
transmitted to this virtual net by ports in this hub. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.2.15.1.2 |
|
lsBusStatsVirtualNetOctetsmandatory
The number of octets in good packets that
were transmitted to this virtual net by ports in this hub. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.2.15.1.3 |
.1.3.6.1.4.1.81.19.3.3.1
·
1 row entry
·
6 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsPortControlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsPortControlTable'
A list of port control entries.
A list of parameters that set up the collection
of extended statistics related to LANswitch ports.
Data is collected in the lsPortExtendedStatsTable.
of extended statistics related to LANswitch ports.
Data is collected in the lsPortExtendedStatsTable.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsPortControlIndexmandatory
An index that uniquely identifies an entry in
the lsPortControlTable. Each such entry defines a function that monitors ports and places statistics about them in the portTable on behalf of this lsPortControlEntry. |
Integer32 | .1.3.6.1.4.1.81.19.3.3.1.1.1 |
|
lsPortControlDataSourcemandatory
This object identifies the source of the data for
this instance of the port function. The statistics in this group reflect all packets on the LANswitch bus that are trasferred by the lsPortFilterTable. This object may n… |
ObjectIdentifierr/w | .1.3.6.1.4.1.81.19.3.3.1.1.2 |
|
lsPortControlTableSizemandatory
The number of ports for which SW counters are
collected by the agent. This number is limited to 5. |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.3.3.1.1.3 |
|
lsPortControlLastDeleteTimemandatory
The value of sysUpTime when the last entry
was deleted from the portion of the portTable associated with this lsPortControlEntry. If no deletions have occurred, this value shall be zero. |
RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.3.1.1.4 |
|
lsPortControlOwnermandatory
The entity that configured this entry and is
therefore using the resources assigned to it. |
RFC1213-MIBDisplayStringr/w | .1.3.6.1.4.1.81.19.3.3.1.1.5 |
|
lsPortControlStatusmandatory
The status of this lsPortControl entry.
If this object is not equal to valid(1), all associated entries in the lsPortTable, shall be deleted by the agent. |
Enumerationr/w | .1.3.6.1.4.1.81.19.3.3.1.1.6 |
.1.3.6.1.4.1.81.19.3.3.2
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsPortFilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsPortFilterTable'
A list of LANswitch ports to be monitored on the high-speed bus. The OID of this table is a legitimate value for the lsPortControlDataSource. When this OID is a source for the host table, a port in the table has the same meaning as an instruction to the agent to collect statistics for all the hosts connected to that port. The maximum size of this table is 5 entries
An entry in the filter table.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsPortFiltermandatory
The port monitored on the LANswitch bus. The value
of this item is: (16*S-1)+P, where S is the slot number in the hub (1..16) and P the port within the slot (1..N). |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.3.3.2.1.1 |
|
lsPortFilterStatusmandatory
The status of this lsPortFilter entry. When the status is
valid, the port defined in the corresponding lsPortFilter is a part of the filter. |
Enumerationr/w Constraints: range: 6-6 |
.1.3.6.1.4.1.81.19.3.3.2.1.2 |
.1.3.6.1.4.1.81.19.3.3.4
·
1 row entry
·
7 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsPortTable'
A list of port entries. Each entry contains statistical data pertaining to a single port. An entry is maintained at all times for each of the LANswitch ports that exist in the hub. This table is not controlled by the lsPortControlTable.
A collection of statistics for a particular LANswitch port.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsPortNumbermandatory
The monitored port. The value of this item is:
16*(S-1)+P, where S is the slot number in the hub (1..16) and P the port within the slot (1..N). |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.3.3.4.1.1 |
|
lsPortInPktsmandatory
The number of good packets transmitted through
this port into the LANswitch bus . |
RFC1155-SMICounter Constraints: range: 4-4 |
.1.3.6.1.4.1.81.19.3.3.4.1.2 |
|
lsPortInFCSErrorsmandatory
The number of packets with FCS errors transmitted
through this port into the LANswitch bus . |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.3.4.1.3 |
|
lsPortInTooLongPktsmandatory
The number of packets longer than 1518 bytes
transmitted through this port into the LANswitch bus . |
RFC1155-SMICounter Constraints: range: 1-255 |
.1.3.6.1.4.1.81.19.3.3.4.1.4 |
|
lsPortInOctetsmandatory
The number of octets in good packets
(excluding framing bits but including FCS octets) transmitted through this port into the LANswitch bus . |
RFC1155-SMICounter Constraints: range: 1-255 |
.1.3.6.1.4.1.81.19.3.3.4.1.5 |
|
lsPortInTotalErrorsmandatory
This item is a summation of all errors on this port.
It contains the total hardware errors related to a specific port. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.3.4.1.6 |
|
lsPortInCollisionsmandatory
This counter is incremented by one for any
CarrierEvent signal on the port for which the CollisionEvent signal on this port is also asserted. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.3.4.1.7 |
.1.3.6.1.4.1.81.19.3.3.6
·
1 row entry
·
6 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsPortExtendedStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsPortExtendedStatsTable'
A list of port entries.
A collection of statistics for a particular
LANswitch port.
LANswitch port.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsPortExtendedStatsNumbermandatory
The monitored port.The value of this item is:
16*(S-1)+P, where S is the slot number in the hub (1..16) and P the port within the slot (1..N). |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.3.3.6.1.1 |
|
lsPortCreationOrdermandatory
An index that defines the relative ordering of
the discovery time of ports captured for a particular lsPortControlEntry. This index shall be between 1 and N, where N is the value of the associated lsPortControlTableSiz… |
Integer32 | .1.3.6.1.4.1.81.19.3.3.6.1.2 |
|
lsPortIndexmandatory
The set of collected port statistics of which
this entry is a part. The set of ports identified by a particular value of this index is associated with the lsPortControlEntry as identified by the same value of lsPortCon… |
Integer32 | .1.3.6.1.4.1.81.19.3.3.6.1.3 |
|
lsPortOutPktsmandatory
The number of packets without errors
transmitted from the LANswitch bus to this port. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.3.6.1.4 |
|
lsPortInBroadcastPktsmandatory
The number of good Ethernet packets directed
towards the broadcast address that were transmitted to the LANswitch bus through this port. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.3.6.1.5 |
|
lsPortInMulticastPktsmandatory
The number of good Ethernet packets
directed to a multicast address that were transmitted to the LANswitch bus through this port. |
RFC1155-SMICounter Constraints: range: 0-440 |
.1.3.6.1.4.1.81.19.3.3.6.1.6 |
.1.3.6.1.4.1.81.19.3.4
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsHostFilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsHostFilterTable'
A list of hosts to be monitored on the high-speed bus by the RMON MIB hosts group. The OID of this table is a legitimate value for the hostControlDataSource. The size of the table is limited to 200 entries.
An entry in the filter table.
Indexes
| Column | Syntax | OID |
|---|---|---|
|
lsHostFilterAddressmandatory
The MAC address of a host monitored on the
high-speed bus. |
OctetString | .1.3.6.1.4.1.81.19.3.4.1.1 |
|
lsHostFilterStatusmandatory
The status of this lsHostFilter entry. When the status is
valid, the host defined in the corresponding lsHostFilter is a part of the filter. |
Enumerationr/w Constraints: range: 0-48 |
.1.3.6.1.4.1.81.19.3.4.1.2 |
.1.3.6.1.4.1.81.19.3.6
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsHostPortFilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsHostPortFilterTable'
A list of ports to be monitored on the high-speed bus. The OID of this table is a legitimate value for the hostControlDataSource. When this OID is a source for the host table, a port in the table has the same meaning as an instruction to the agent to collect statistics for all the hosts connected to that port. The size of this table is limited to 5 entries.
An entry in the filter table.
Indexes
| Column | Syntax | OID |
|---|---|---|
|
lsHostPortFiltermandatory
The port monitored on the LANswitch bus. The value
of this item is: 16*(S-1)+P, where S is the slot number in the hub (1..16) and P the port within the slot (1..N). |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.3.6.1.1 |
|
lsHostPortFilterStatusmandatory
The status of this lsHostPortFilter entry. When the
status is valid, the hosts defined by the corresponding lsHostPortFilter are a part of the filter. |
Enumerationr/w Constraints: range: 384-384 |
.1.3.6.1.4.1.81.19.3.6.1.2 |
.1.3.6.1.4.1.81.19.3.8
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsMatrixFilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsMatrixFilterTable'
A list of hosts to be monitored on the high-speed bus by the RMON MIB matrix group. The OID of this table is a legitimate value for the hostControlDataSource. The size of the table is limited to 200 entries.
An entry in the filter table.
Indexes
| Column | Syntax | OID |
|---|---|---|
|
lsMatrixFilterAddressmandatory
The MAC address of a host monitored on the
high-speed bus. |
OctetString | .1.3.6.1.4.1.81.19.3.8.1.1 |
|
lsMatrixFilterStatusmandatory
The status of this lsMatrixFilter entry. When the status
is valid, the hosts defined by the corresponding lsMatrixFilter are a part of the filter. |
Enumerationr/w Constraints: range: 6-6 |
.1.3.6.1.4.1.81.19.3.8.1.2 |
.1.3.6.1.4.1.81.19.3.10
·
1 row entry
·
4 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsHostTimePortCorrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsHostTimePortCorrTable'
An addition to the RMON MIBs hostTimeTable. This table contains a list of MAC addresses that were monitored on the high-speed bus and the switch ports to which they are connected. The index of this table is the same as for the standard RMON hostTimeTable. Indexes are hostTimeCreationOrder and hostTimeIndex. The MAC address is stored in hostTimeAddress. The port to which the MAC address is connected hostTimePortConnection.
An entry in the MAC to port correlation table.
Indexes
| Column | Syntax | OID |
|---|---|---|
|
hostTimeAddressmandatory
The physical address of this host.
|
OctetString Constraints: range: 1-65535 |
.1.3.6.1.4.1.81.19.3.10.1.1 |
|
hostTimeCreationOrdermandatory
An index that uniquely identifies an entry in
the hostTime table among those entries associated with the same hostControlEntry. This index shall be between 1 and N, where N is the value of the associated hostControlTab… |
Integer32 | .1.3.6.1.4.1.81.19.3.10.1.2 |
|
hostTimeIndexmandatory
The set of collected host statistics of which
this entry is a part. The set of hosts identified by a particular value of this index is associated with the hostControlEntry as identified by the same value of hostControl… |
Integer32 | .1.3.6.1.4.1.81.19.3.10.1.3 |
|
hostTimePortConnectionmandatory
The switch port to which this hostTimeAddress is connected.
The coding of the port number varies for different hubs and packplanes. For the LANSwitch HSB the value of this item is: The value of this item is: 32*(S… |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.3.10.1.4 |
.1.3.6.1.4.1.81.19.3.11
·
1 row entry
·
23 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsHistoryTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsHistoryTable'
A list of High Speed Bus history entries.
An historical sample of LANswitch statistics on a HSB.
This sample is associated with the historyControlEntry which set up
the parameters for a regular collection of these samples.
This sample is associated with the historyControlEntry which set up
the parameters for a regular collection of these samples.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsHistoryIndexmandatory
The history of which this entry is a part. The history identified by a particular value of this
index is the same history as identified by the same value of historyControlIndex. |
Integer32 Constraints: range: 0-2147483647 |
.1.3.6.1.4.1.81.19.3.11.1.1 |
|
lsHistorySampleIndexmandatory
An index that uniquely identifies the particular
sample this entry represents among all samples associated with the same lshistoryControlEntry. This index starts at 1 and increases by one as each new sample is taken. |
Integer32 | .1.3.6.1.4.1.81.19.3.11.1.2 |
|
lsHistoryIntervalTimemandatory
The value of sysUpTime when this bucket was sampled .
|
RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.3 |
|
lsHistoryStatsDropEventsmandatory
The total number of events in which packets were dropped by the probe due to lack of
resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has … |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.4 |
|
lsHistoryStatsPktsmandatory
The total number of packets (including error packets) received on the LANswitch bus.
|
RFC1155-SMICounter Constraints: range: 1-65535 |
.1.3.6.1.4.1.81.19.3.11.1.5 |
|
lsHistoryStatsOctetsmandatory
The total number of octets of data (including those in bad packets) received on the
LANswitch bus (excluding framing bits but including FCS octets). |
RFC1155-SMICounter Constraints: range: 1-2147483647 |
.1.3.6.1.4.1.81.19.3.11.1.6 |
|
lsHistoryStatsEthBroadcastPktsmandatory
The total number of good Ethernet packets received that were directed to the broadcast
address. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.7 |
|
lsHistoryStatsEthMulticastPktsmandatory
The total number of good packets received that were directed to a multicast address.
Note that this number does not include packets directed to the broadcast address. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.8 |
|
lsHistoryStatsGoodEthPktsmandatory
The total number of good Ethernet packets received on the LANswitch bus.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.9 |
|
lsHistoryStatsGoodEthOctetsmandatory
The total number of octets that were received on the LANswitch bus in good
Ethernet packets (excluding framing bits but including FCS octets). |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.10 |
|
lsHistoryStatsBadEthPktsmandatory
The total number of bad Ethernet packets received on the LANswitch bus.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.11 |
|
lsHistoryStatsBadEthOctetsmandatory
The total number of octets that were received on the LANswitch bus in bad Ethernet packets (excluding framing bits but including FCS octets).
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.12 |
|
lsHistoryStatsNonEthPktsmandatory
The total number of packets received on the LANswitch bus in non Ethernet packets.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.13 |
|
lsHistoryStatsNonEthOctetsmandatory
The total number of octets that were received on the LANswitch bus in non Ethernet packets (excluding framing bits but including FCS octets).
|
RFC1155-SMICounter Constraints: range: 1-65535 |
.1.3.6.1.4.1.81.19.3.11.1.14 |
|
lsHistoryStatsPriority1Pktsmandatory
The total number of packets (including error packets) received on the LANswitch
bus whose priority is that defined for this entry. |
RFC1155-SMICounter Constraints: range: 1-2147483647 |
.1.3.6.1.4.1.81.19.3.11.1.15 |
|
lsHistoryStatsPriority1Octetsmandatory
The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.16 |
|
lsHistoryStatsPriority2Pktsmandatory
The total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.17 |
|
lsHistoryStatsPriority2Octetsmandatory
The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.18 |
|
lsHistoryStatsPriority3Pktsmandatory
The total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.19 |
|
lsHistoryStatsPriority3Octetsmandatory
The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.20 |
|
lsHistoryStatsPriority4Pktsmandatory
The total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.21 |
|
lsHistoryStatsPriority4Octetsmandatory
The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.3.11.1.22 |
|
lsHistoryBusUtilizationmandatory
The utilization of the LANswitch bus, expressed in percents of the maximum LANswitch traffic possible.
|
Integer32 | .1.3.6.1.4.1.81.19.3.11.1.23 |
.1.3.6.1.4.1.81.19.4.1.1
·
1 row entry
·
36 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lstIntPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lstIntPortTable'
An entry in the table, containing data about
a LANswitch port of LANswitch Token-Ring modules.
a LANswitch port of LANswitch Token-Ring modules.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lstIntPortGroupIdmandatory
Id of the group to which the switch port belongs.
|
Integer32 | .1.3.6.1.4.1.81.19.4.1.1.1.1 |
|
lstIntPortIdmandatory
Switch port Id in module
|
Integer32 | .1.3.6.1.4.1.81.19.4.1.1.1.2 |
|
lstIntPortSidebandModemandatory
Enable Sideband mode on internal port. In this mode,
MAC level management of all rings can be done. |
Enumerationr/w | .1.3.6.1.4.1.81.19.4.1.1.1.3 |
|
lstIntPortTotalOctetsmandatory
Total number of octets circling in the ring. It is the
sum of local octets, in octets and out octets. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.4.1.1.1.4 |
|
lstIntPortTotalTrafficmandatory
Total traffic in ring as part of the maximum possible
utilization, 4Mbps or 16Mbps, expressed in percents. It is the sum of local traffic, in traffic and out traffic. |
Integer32 | .1.3.6.1.4.1.81.19.4.1.1.1.5 |
|
lstIntPortLocalOctetsmandatory
Number of octets local to the ring. The local traffic
includes only traffic between stations on the local ring. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.4.1.1.1.6 |
|
lstIntPortLocalTrafficmandatory
Local traffic in ring as part of the maximum possible
utilization, 4Mbps or 16Mbps, expressed in percents. The local traffic includes only traffic between stations on the local ring. |
Integer32 | .1.3.6.1.4.1.81.19.4.1.1.1.7 |
|
lstIntPortInOctetsmandatory
Number of octets passing in to the HSB from the ring.
The In traffic includes only traffic going from stations on the local ring to stations on other rings. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.4.1.1.1.8 |
|
lstIntPortInTrafficmandatory
In traffic to the HSB from the ring as part of the
maximum possible utilization, 4Mbps or 16Mbps, expressed in percents. The In traffic includes only traffic going from stations on the local ring to stations on othe… |
Integer32 | .1.3.6.1.4.1.81.19.4.1.1.1.9 |
|
lstIntPortOutOctetsmandatory
Number of octets passing out from the HSB to
the ring. The Out traffic includes only traffic going to stations on the local ring from stations on other rings. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.4.1.1.1.10 |
|
lstIntPortOutTrafficmandatory
Out traffic from the HSB to the ring as part
of the maximum possible utilization, 4Mbps or 16Mbps, expressed in percents. The Out traffic includes only traffic going to stations on the local ring from stations on o… |
Integer32 Constraints: range: 32-32 |
.1.3.6.1.4.1.81.19.4.1.1.1.11 |
|
lstIntPortTotalFramesmandatory
Total number of frames in the ring.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.4.1.1.1.12 |
|
lstIntPortLostFramesmandatory
Number of lost frames because of Back Pressure.
|
RFC1155-SMICounter Constraints: range: 32-32 |
.1.3.6.1.4.1.81.19.4.1.1.1.13 |
|
lstIntPortClaimFramesmandatory
Number of Claim-Token frames in the ring.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.4.1.1.1.16 |
|
lstIntPortPurgeFramesmandatory
Number of Ring-Purge frames in the ring.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.19.4.1.1.1.17 |
|
lstIntPortNormallyCloseOpenmandatory
Defines the IO mode of the switch port:
normally close or normally open. When the port is in 'normallyOpen' mode, all packets enter the port regardless to CAM content. |
Enumerationr/w | .1.3.6.1.4.1.81.19.4.1.1.1.18 |
|
lstIntPortSlicingEnablemandatory
Packet slicing mechanism for decreasing
the delay of packets transmission in the HSB. Value 'on' enables the slicing mechanism. |
Enumerationr/w Constraints: range: 6-6 |
.1.3.6.1.4.1.81.19.4.1.1.1.19 |
|
lstIntPortSliceLengthmandatory
The slice length in bytes. It determines
the delay of packet's transmission through the HSB. |
Integer32r/w Constraints: range: 1-4095 |
.1.3.6.1.4.1.81.19.4.1.1.1.20 |
|
lstIntPortUNAddrmandatory
MAC address of the Upstream Neighbor
of the line interface. |
OctetString Constraints: range: 1-4095 |
.1.3.6.1.4.1.81.19.4.1.1.1.21 |
|
lstIntPortMACAddressmandatory
MAC address of the line interface.
|
OctetString | .1.3.6.1.4.1.81.19.4.1.1.1.22 |
|
lstIntPortSMPTransmitEnablemandatory
Enable SMP MAC frame transmission by line
interface during single-station situation. |
Enumerationr/w | .1.3.6.1.4.1.81.19.4.1.1.1.23 |
|
lstIntPortIPGLengthmandatory
Number of bytes interval between frames
transmission of the line interface to the ring. |
Integer32r/w | .1.3.6.1.4.1.81.19.4.1.1.1.24 |
|
lstIntPortBPDummyWindowmandatory
The time (in 0.25ms) between Dummy frames
sendings during Back Pressure situation of the line interface. |
Integer32r/w | .1.3.6.1.4.1.81.19.4.1.1.1.25 |
|
lstIntPortBPTokenWindowmandatory
The time (in 0.25ms) until Token release
during Back Pressure situation of the line interface. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.4.1.1.1.26 |
|
lstIntPortTransmitWindowmandatory
The time (in 0.25ms) of line interface
transmission until Token release. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.4.1.1.1.27 |
|
lstIntPortBlockingPrioritymandatory
The priority of the line interface during
Back Pressure situation. |
Integer32r/w | .1.3.6.1.4.1.81.19.4.1.1.1.28 |
|
lstIntPortNormalPrioritymandatory
The priority of the line interface for HSB
packets transmission into the ring. |
Integer32r/w Constraints: range: 0-36 |
.1.3.6.1.4.1.81.19.4.1.1.1.29 |
|
lstIntPortDummyMVmandatory
Content of MV (Major Vector) field in Dummy
frame during Back Pressure of line interface. |
Integer32r/w | .1.3.6.1.4.1.81.19.4.1.1.1.30 |
|
lstIntPortTxConsecutiveBusiesThreshmandatory
The threshold of the number of consecutive
busies counter. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.4.1.1.1.31 |
|
lstIntPortTxBufFullThreshmandatory
Threshold indicator for frames buffer full.
|
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.4.1.1.1.32 |
|
lstIntPortRxEmpty0mandatory
Upper threshold pointer of Rx buffer.
Determines the degree of buffer overflow and back pressure efficiency. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.4.1.1.1.33 |
|
lstIntPortRxEmpty1mandatory
Middle threshold pointer of Rx buffer.
Determines the degree of buffer overflow and back pressure efficiency.. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.4.1.1.1.34 |
|
lstIntPortRxEmpty2mandatory
Lower threshold pointer of Rx buffer. Determines
the degree of buffer overflow and back pressure efficiency. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.4.1.1.1.35 |
|
lstIntPortRxFullmandatory
Rx full threshold pointer. Determines the degree
of buffer overflow and back pressure efficiency. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.4.1.1.1.36 |
|
lstIntPortBPEnablemandatory
Enable/disable the Back Pressure mechanism.
|
Enumerationr/w | .1.3.6.1.4.1.81.19.4.1.1.1.37 |
|
lstIntPortRouteSidebandmandatory
Set the internal port ability to get from the HSB sideband packets. The
value 'on' enables the routing of sideband packet from the HSB into the internal port. |
Enumerationr/w | .1.3.6.1.4.1.81.19.4.1.1.1.38 |
.1.3.6.1.4.1.81.19.5
·
1 row entry
·
3 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lseWANTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lseWANTable'
LAN Switch WAN data table. Implementation of this table is mandatory for all LANswitch modules with WAN ports.
Entry in the table.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lseWANGroupIdmandatory
Slot number in which the module is located.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.5.1.1 |
|
lseWANPortIdmandatory
WAN port index.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.5.1.2 |
|
lseWANConnectionmandatory
WAN connection status.
|
Enumeration | .1.3.6.1.4.1.81.19.5.1.3 |
.1.3.6.1.4.1.81.19.7.1
·
1 row entry
·
14 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk vnsPacketTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::vnsPacketTable'
VNS packets data table. Implementation of this table is mandatory for 3LS (3rd layer switch) module.
Entry in the table.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
vnsPacketMACAddressmandatory
The Mac Address of the sending station.
|
OctetString | .1.3.6.1.4.1.81.19.7.1.1.1 |
|
vnsPacketProtocolTypeMaskmandatory
This is a mask of the exising protocols.
Bit(0)='1' when IP protocol exist and '0' otherwise, Bit(1)='1' when IPX protocol exist and '0' otherwise, all other bits are '0' for the moment. |
OctetString | .1.3.6.1.4.1.81.19.7.1.1.2 |
|
vnsPacketIPAddressmandatory
The IP address of the packet's sending station.
In case the typeaddress is not IP this field will be 0.0.0.0. |
RFC1155-SMIIpAddress Type Constraints: range: 4 |
.1.3.6.1.4.1.81.19.7.1.1.3 |
|
vnsPacketIPNetMaskmandatory
The IP Address Mask from the IP Interface Table.
|
RFC1155-SMIIpAddress Type Constraints: range: 4 |
.1.3.6.1.4.1.81.19.7.1.1.4 |
|
vnsPacketIPXnetworkmandatory
The IPX NetWork Address of the packet's sending station.
In case that the typeaddress is not IPX this field will be 0.0.0.0. |
OctetString | .1.3.6.1.4.1.81.19.7.1.1.5 |
|
vnsPacketStationTypemandatory
The Station Type indicates from where comes the packets
in the case of the IPX protocol. |
Enumeration | .1.3.6.1.4.1.81.19.7.1.1.6 |
|
vnsPacketPortGroupIdmandatory
Index which identifies the group inside the chassis for which this
entry contains information. It equals with the slot number. |
Integer32 | .1.3.6.1.4.1.81.19.7.1.1.7 |
|
vnsPacketPortIdmandatory
Index which identifies the port inside the group for which this
entry contains information. It equals with the port number. |
Integer32 | .1.3.6.1.4.1.81.19.7.1.1.8 |
|
vnsPacketBackbonePortmandatory
The value 2 indicates that the port source of the packet is a
backbone port. |
Enumeration | .1.3.6.1.4.1.81.19.7.1.1.9 |
|
vnsPacketExpectedVLANmandatory
The value of this item is the VLAN number that the packet had to have
according to it's address. |
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.7.1.1.10 |
|
vnsPacketDetectedVLANmandatory
The value of this item is the detected VLAN number of the arrived packet.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.19.7.1.1.11 |
|
vnsPacketBoxAgentIPmandatory
The IP Address of the Hub's BoxAgent where the 3LS (3rd layer switch) module exist.
|
RFC1155-SMIIpAddress Type Constraints: range: 4 |
.1.3.6.1.4.1.81.19.7.1.1.12 |
|
vnsPacketExpectedIfNamemandatory
The value of this item is the name of the interface the packet was expected to be received on according to it's address.
|
RFC1213-MIBDisplayString | .1.3.6.1.4.1.81.19.7.1.1.13 |
|
vnsPacketDetectedIfNamemandatory
The value of this item is the name of the interface the packet was actually received on.
|
RFC1213-MIBDisplayString | .1.3.6.1.4.1.81.19.7.1.1.14 |
.1.3.6.1.4.1.81.23.3.4
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk ethTopMessageResultTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::ethTopMessageResultTable'
A table that contains 3 items with the results of the topology messages received by the agent.
An entry in the table, containing part of the received data.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
ethTopMessageResultIdmandatory
The table's index. Can assume the values 1,2, or 3.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.23.3.4.1.1 |
|
ethTopMessageResultmandatory
A row in the Topology Messages result table. Each row contains up to 44 elements.
|
OctetString | .1.3.6.1.4.1.81.23.3.4.1.2 |
.1.3.6.1.4.1.81.23.3.6
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk ethTopMACFindResultTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::ethTopMACFindResultTable'
A table that contains 4 rows with the results of the MACFind process. Each row contains the results for one of the hub's buses. The number of items supported is equal to the number of buses supported by the agent.
An entry in the table, containing one LSA item.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
ethTopMACFindBusmandatory
The bus for which the results are reported.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.23.3.6.1.1 |
|
ethTopMACFindResultmandatory
The results of the search for the requested MAC addresses fo the relevant bus. The format is: MAC (6 bytes), slot (1 byte), port (1 byte).
If the Agent doesn't find a MAC's correlation, the slot and port will be '0'. |
OctetString | .1.3.6.1.4.1.81.23.3.6.1.2 |
.1.3.6.1.4.1.81.23.3.7
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk ethTopLSATable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::ethTopLSATable'
A table that contains 8 rows with the last source addresses found on the hub's ports. Each row in the table reports the last source addresses for specific slots in the hub: #1: modules 1,2,17,18; #5: modules 9,10,25, 26; #2: modules 3,4,19,20; #6: modules 11,12,27, 28; #3: modules 5,6,21,22; #7: modules 13,14,29,30; #4: modules 7,8,23,24; #8: modules 15,16,31,32; The data in the items appears by the slot order defined above. All 8 items exist even if some of them are empty.
An entry in the table, containing one LSA item.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
ethTopLSAIdmandatory
The table's index. Assumes values 1,2,3,...,8.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.23.3.7.1.1 |
|
ethTopLSAmandatory
This item contains the last source addresses for modules in related slots. For each port the data is: slot (one byte), port (one byte), address (6 bytes). For none existing ports the LSA will be 0.
The first bit (MSB) … |
OctetString | .1.3.6.1.4.1.81.23.3.7.1.2 |
.1.3.6.1.4.1.81.23.3.8
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk ethTopAddressTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::ethTopAddressTable'
A table that contains the MAC addresses used by the agent for the topology messages.
An entry in the topology address table. The number of entries is
equal to the number of Ethernet
buses supported by the agent.
equal to the number of Ethernet
buses supported by the agent.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
ethTopBusmandatory
The bus for which this address is defined.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.23.3.8.1.1 |
|
ethTopAddressmandatory
The MAC address used by the agent for the topology discovery
process on the related bus. |
OctetStringr/w | .1.3.6.1.4.1.81.23.3.8.1.2 |
.1.3.6.1.4.1.81.30.1.1
·
1 row entry
·
2 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk alarmMonitorStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::alarmMonitorStatusTable'
A list of alarms status for Alarm entries.
Each entry contains an index (appropriate to specific alarmIndex item)
and the alarmed status of this alarm entry
and the alarmed status of this alarm entry
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
alarmMonitorStatusIndexmandatory
An index that uniquely identifies an entry in the alarmMonitorStatusTable.
This index is the same as the appropriate alarm Table. |
Integer32 | .1.3.6.1.4.1.81.30.1.1.1.1 |
|
alarmMonitorStatusmandatory
The alarms' status for the appropriate alarm table
1 - ok 2 - alarmState. |
Enumeration | .1.3.6.1.4.1.81.30.1.1.1.2 |
.1.3.6.1.4.1.81.30.3.1
·
1 row entry
·
4 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk portHistoryExtendedControlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::portHistoryExtendedControlTable'
A list of extended history control entries.
A list of extended parameters that set up a periodic sampling of statistics.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
portHistoryExtendedControlCreateTimemandatory
The value of sysUpTime at the creation of the control row and start of the history
collection index with the same value of the historyControlIndex. |
RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.1.1.1 |
|
The index of the last bucket that was stored to the history table.
|
Integer32 Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.81.30.3.1.1.2 |
|
The number of buckets stored in the probe.
|
Integer32 | .1.3.6.1.4.1.81.30.3.1.1.3 |
|
portHistoryExtendedControlNamemandatory
The name of the this history collection.
|
RFC1213-MIBDisplayStringr/w | .1.3.6.1.4.1.81.30.3.1.1.4 |
.1.3.6.1.4.1.81.30.3.2
·
1 row entry
·
7 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk lsPortHistoryTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::lsPortHistoryTable'
A list of LANswitch port history entries.
An historical sample of port switch statistics with the historyControlEntry,
which set up the parameters for a regular collection of these samples.
which set up the parameters for a regular collection of these samples.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
lsPortHistoryIndexmandatory
The history of which this entry is a part. The history identified by a particular value of this
index is the same history as identified by the same value of historyControlIndex. |
Integer32 | .1.3.6.1.4.1.81.30.3.2.1.1 |
|
lsPortHistorySampleIndexmandatory
An index that uniquely identifies the particular sample,
this entry represents among all samples associated with the same lshistoryControlEntry. This index starts at 1 and increases by one as each new sample is taken. |
Integer32 | .1.3.6.1.4.1.81.30.3.2.1.2 |
|
lsPortHistoryIntervalTimemandatory
The value of sysUpTime at the start of the interval
over which this sample was measured. |
RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.2.1.3 |
|
lsPortHistoryBoxConfigurationmandatory
Octet String build by concatenating the genGroupType of the
maximum 16 modules in the LANSwitch box. By reading this variable a management application can draw a list of the LANSwitch modules and ports configuration re… |
OctetString | .1.3.6.1.4.1.81.30.3.2.1.4 |
|
lsPortHistoryPktsmandatory
The total number of good packets received on the port.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.2.1.5 |
|
lsPortHistoryCollisionsmandatory
The best estimate of the total number of collisions
on this port during this sampling interval. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.2.1.6 |
|
lsPortHistoryTotalErrorsmandatory
The total number of errors detected by the switching hardware on this port,
including FCS errors and too long packets. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.2.1.7 |
.1.3.6.1.4.1.81.30.3.3
·
1 row entry
·
9 columns
Uses the avaya variant from
Command help
/opt/observium/mibs/avaya.
Walk scPortHistoryTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'APPLIC-MIB' -M '/opt/observium/mibs/avaya:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'APPLIC-MIB::scPortHistoryTable'
A list of Xswitch port history entries.
An historical sample of port switch statistics with the historyControlEntry,
which set up the parameters for a regular collection of these samples.
which set up the parameters for a regular collection of these samples.
Indexes
No indexes recorded
| Column | Syntax | OID |
|---|---|---|
|
scPortHistoryIndexmandatory
The history of which this entry is a part. The history identified by a particular value of this
index is the same history as identified by the same value of historyControlIndex. |
Integer32 | .1.3.6.1.4.1.81.30.3.3.1.1 |
|
scPortHistorySampleIndexmandatory
An index that uniquely identifies the particular sample,
this entry represents among all samples associated with the same scHistoryControlEntry. This index starts at 1 and increases by one as each new sample is taken. |
Integer32 | .1.3.6.1.4.1.81.30.3.3.1.2 |
|
scPortHistoryIntervalTimemandatory
The value of sysUpTime at the start of the interval
over which this sample was measured. |
RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.3.1.3 |
|
scPortHistoryBoxConfigurationmandatory
Octet String build by concatenating the genGroupType of the
maximum 14 modules in the Meritage box or 4 boxes in the Visage stack. By reading this variable a management application can draw a list of the modules (box… |
OctetString | .1.3.6.1.4.1.81.30.3.3.1.4 |
|
scPortHistoryGoodPktsRecmandatory
The total number of good packets received by the port.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.3.1.5 |
|
scPortHistoryGoodNonUnicastPktsRecmandatory
The total number of good packets received that were
directed to multicat or broadcast address. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.3.1.6 |
|
scPortHistoryCollisionsmandatory
The best estimate of the total number of collisions on the
Ethernet segment connected to the port. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.3.1.7 |
|
scPortHistoryBadPktsmandatory
The total number of bad packets filtered by the port.
This item is the summation of: scEthPortCRCAlignErrors, scEthPortOversizePkts, scEthPortFragments and scEthPortJabber. |
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.3.1.8 |
|
scPortHistoryGoodPktsSentmandatory
The total number of good packets sent by the port.
|
RFC1155-SMICounter Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.81.30.3.3.1.9 |