AP80-PRIVATE-MIB Table View

Table of descriptive and status information about
configuration of each RS-232 line in this system

lineEntry row .1.3.6.1.4.1.14823.2.3.2.2.1.1

An entry in the table, containing information
about configuration in one RS232 line of the Access Point.

Indexes

lineIndex

Column	Syntax	OID
lineIndex This is defined as RS-232 index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.2.1.1.1
lineDataBits This is defined as number of data bits for the RS232 interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.2.1.1.2
lineParity This is defined as parity of the RS232 interface.	Enumeration Enumerated Values: 1 odd 2 even 99 none	.1.3.6.1.4.1.14823.2.3.2.2.1.1.3
lineSpeed This is defined as the speed of the RS-232 interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.2.1.1.4
lineStopBits This is defined as the number of stop bits for the RS-232 interface.	SNMPv2-SMIInteger32 Constraints: range: 0-9	.1.3.6.1.4.1.14823.2.3.2.2.1.1.5

Table of descriptive and status information about
configuration of each switch port (including expansion slot)
in this system. This table also contains information
about each trunk (similar to Cisco's EtherChannel).

portEntry row .1.3.6.1.4.1.14823.2.3.2.3.1.1

An entry in the table, containing information
about configuration in one switch port of the switch.

Indexes

portIndex

Column	Syntax	OID
portIndex This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.3.1.1.1
portName Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later).	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.14823.2.3.2.3.1.1.2
portType Indicates the port type.	Enumeration Enumerated Values: 1 other 2 hundredBaseTX 3 hundredBaseFX 4 thousandBaseSX 5 thousandBaseLX 6 thousandBaseT 7 thousandBaseGBIC 8 thousandBaseMiniGBIC	.1.3.6.1.4.1.14823.2.3.2.3.1.1.3
portSpeedDpxCfg Indicates the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) …	Enumeration Enumerated Values: 1 reserved 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000	.1.3.6.1.4.1.14823.2.3.2.3.1.1.4
portFlowCtrlCfg (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in…	Enumeration Enumerated Values: 1 enabled 2 disabled 3 backPressure 4 dot3xFlowControl Constraints: range: 0-9	.1.3.6.1.4.1.14823.2.3.2.3.1.1.5
portCapabilities Port capabilities.	Enumeration Enumerated Values: 1 portCap10full 2 portCap100half 3 portCap100full 4 portCap1000half 5 portCap1000full 6 reserved6 7 reserved7 8 reserved8 9 reserved9 10 reserved10 11 reserved11 12 reserved12 13 reserved13 14 portCapSym 15 portCapFlowCtrl 99 portCap10half	.1.3.6.1.4.1.14823.2.3.2.3.1.1.6
portAutonegotiation Whether autonegotiation is enabled.	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.3.1.1.7
portSpeedDpxStatus The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk and the result is inconsistent among its member ports, this …	Enumeration Enumerated Values: 1 error 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000	.1.3.6.1.4.1.14823.2.3.2.3.1.1.8
portFlowCtrlStatus (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trunk and the result is inconsistent among its member ports, thi…	Enumeration Enumerated Values: 1 error 2 backPressure 3 dot3xFlowControl 4 none	.1.3.6.1.4.1.14823.2.3.2.3.1.1.9

Table of descriptive and status information about
configuration of each authentication server.

dot11AuthenticationServerEntry row .1.3.6.1.4.1.14823.2.3.2.7.2.1

An entry in the table, containing information
about configuration of one authentication server of the AP.

Indexes

dot11AuthenticationServerIndex

Column	Syntax	OID
dot11AuthenticationServerIndex Index of the Authentication Server	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.7.2.1.1
dot11AuthenticationServer This value indicates the IP address of the authentication server.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.14823.2.3.2.7.2.1.2
dot11AuthenticationPort This value indicates the UDP Port used by the authentication server.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.14823.2.3.2.7.2.1.3
dot11AuthenticationKey This value indicates the shared key used by the authentication server.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.14823.2.3.2.7.2.1.4
dot11AuthenticationRetransmit This value indicates the retransmit timer length used by the authentication server.	Integer32r/w Constraints: range: 1-30	.1.3.6.1.4.1.14823.2.3.2.7.2.1.5
dot11AuthenticationTimeout This value indicates the Timeout value(sec) used by the authentication server.	Integer32r/w Constraints: range: 0-9 range: 1-60	.1.3.6.1.4.1.14823.2.3.2.7.2.1.6
dot11AuthenticationAcctPort The port number for radius server accounting.	Integer32r/w Constraints: range: 1-20 range: 1024-65535	.1.3.6.1.4.1.14823.2.3.2.7.2.1.7
dot11AuthenticationAcctInterimUpdate This value indicates the Timeout value(sec) used by the radius server interim update.	Integer32r/w Constraints: range: 60-86400	.1.3.6.1.4.1.14823.2.3.2.7.2.1.8
dot11AuthenticationMACAddressFormat This value indicates the MAC address format from Radius MAC authentication. no-delimiter format: aabbccddeeff single-dash format: aabbcc-ddeeff multi-dash format: aa-bb-cc-dd-ee-ff multi-colon format: aa:bb:cc:…	Enumerationr/w Enumerated Values: 1 no-delimiter 2 single-dash 3 multi-dash 4 multi-colon	.1.3.6.1.4.1.14823.2.3.2.7.2.1.9
dot11AuthenticationVLANIDFormat This value indicates the VLAN ID format from Radius server.	Enumerationr/w Enumerated Values: 1 hex 2 ascii	.1.3.6.1.4.1.14823.2.3.2.7.2.1.10

Table of status information about
each configured MAC Address Filtering Entry.

dot11FilterEntry row .1.3.6.1.4.1.14823.2.3.2.7.3.2.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

dot11FilterAddress

Column	Syntax	OID
dot11FilterAddress This value indicates the MAC address of the filter entry.	MacAddress Type Constraints: range: 6	.1.3.6.1.4.1.14823.2.3.2.7.3.2.1.1
dot11FilterStatus This value indicates the Status of the filter entry. Ifallowed, the client is allowed access to the network. If disallowed, the no frames will be forwarded to the network from the client.	Enumerationr/w Enumerated Values: 30 allowed 31 denied 32 delete	.1.3.6.1.4.1.14823.2.3.2.7.3.2.1.2

Table of descriptive and status information about
configuration of supplicant

dot11AuthenticationSupplicantEntry row .1.3.6.1.4.1.14823.2.3.2.7.5.1

An entry in the table, containing information
about configuration of one supplicant.

Indexes

dot11AuthenticationSuppIndex

Column	Syntax	OID
dot118021xSuppIndex Index of the interface for which this supplicant is running. Currently only the ethernet interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.7.5.1.1
dot118021xSuppState This object is used to enable or disable the 802.1x supplicant.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.14823.2.3.2.7.5.1.2
dot118021xSuppUser This value indicates the username for supplicant. If value is configured, will display ****. Else will display EMPTY.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.14823.2.3.2.7.5.1.3
dot118021xSuppPasswd This value indicates the password for supplicant. If value is configured, will display ****. Else will display EMPTY.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.14823.2.3.2.7.5.1.4

Table of descriptive and status information about
configuration of 8021x for each Vap.

dot11VapAuthenticationEntry row .1.3.6.1.4.1.14823.2.3.2.7.6.1

An entry in the table, containing information
about configuration of 8021x for each Vap of the AP.

Indexes

dot11Vap8021xIndex

Column	Syntax	OID
dot11Vap8021xIndex Index for configuration.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.7.6.1.1
dot11Vap8021xState This attribute indicates that the Enterprise the state of the 802.1x authentication algorithm.	Enumerationr/w Enumerated Values: 0 disabled 1 supported 2 required	.1.3.6.1.4.1.14823.2.3.2.7.6.1.2
dot11Vap8021xBroadcastKeyRefreshRate The number (in minutes) between changing the broadcast key for 802.1x and WPA clients	Integer32r/w Constraints: range: 0-1440	.1.3.6.1.4.1.14823.2.3.2.7.6.1.3
dot11Vap8021xSessionKeyRefreshRate The number (in minutes) between changing session keys for 802.1x and WPA clients	Integer32r/w Constraints: range: 0-1440	.1.3.6.1.4.1.14823.2.3.2.7.6.1.4
dot11Vap8021xReauthenticationTimeout The number (in minutes) between forcing 802.1x clients to reauthenticate	Integer32r/w Constraints: range: 0-1440	.1.3.6.1.4.1.14823.2.3.2.7.6.1.5
dot11VapAuthMACAuthenticationType This value indicates the type of mac authentication in use.	Enumerationr/w Enumerated Values: 0 disabled 1 local 2 remote	.1.3.6.1.4.1.14823.2.3.2.7.6.1.6
dot11VapAuthMACAuthenticationTimeout The number (in minutes) between forcing Radius MAC to authenticate.	Integer32r/w Constraints: range: 0-1440	.1.3.6.1.4.1.14823.2.3.2.7.6.1.7

Table used to manage the Vlans for each
wireless interface.

enterpriseApNativeVlanEntry row .1.3.6.1.4.1.14823.2.3.2.9.3.1

An entry in the table, containing information
about vlan configuration of one wireless interface.

Indexes

nativeVlanIfIndex nativeVlanSsidNumber

Column	Syntax	OID
nativeVlanIfIndex Interface Index of the wireless interface for which the vlan is assigned to.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.9.3.1.1
nativeVlanSsidNumber Associated Number for Service Set Id (SSID) of the wireless interface for which the vlan is assigned to. Note: This is for future support of multiple SSIDs per radio interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.9.3.1.2
nativeVlanVlanId This value indicates the native VLAN id of the wireless interface associated with the if index and the SSID number(if it is not 0).	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.9.3.1.3

Table of descriptive and status information about
configuration of the filter protocol table.

enterpriseApFilterProtocolEntry row .1.3.6.1.4.1.14823.2.3.2.10.4.1

An entry in the filter protocol table, containing information
about configuration of one filter table entry.

Indexes

enterpriseApFilterProtocolIndex

Column	Syntax	OID
enterpriseApFilterProtocolIndex Index of the Protocol Filters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.10.4.1.1
enterpriseApFilterProtocolName This value indicates the name of the protocol filter. One of the following: Aironet_DDP, Appletalk_ARP, ARP, Banyan, Berkeley_Trailer_Negotiation, CDP, DEC_LAT, DEC_MOP, DEC_MOP_Dump_Load, DEC_XNS, EAPOL, Enet_Confi…	DisplayString	.1.3.6.1.4.1.14823.2.3.2.10.4.1.2
enterpriseApFilterProtocolISODesignator This value indicates the name of the protocol filter.	DisplayString	.1.3.6.1.4.1.14823.2.3.2.10.4.1.3
enterpriseApFilterProtocolState This value indicates whether the protocol filter is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.10.4.1.4

Table of descriptive and status information about
configuration of the Uplink Port MAC Address Filter Table.

uplinkPortMACAddrFilteringEntry row .1.3.6.1.4.1.14823.2.3.2.10.5.3.1

An entry in Uplink Port MAC Address Filter Table.

Indexes

uplinkPortMacAddrIndex

Column	Syntax	OID
uplinkPortMacAddrIndex The index for Uplink Port MAC Address Filter Table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.10.5.3.1.1
uplinkPortMACAddr The MAC Address of wireless clients which allowed to communicate on subnet.	MacAddress Type Constraints: range: 6	.1.3.6.1.4.1.14823.2.3.2.10.5.3.1.2

Table of descriptive and status information about
configuration of each syslog server.

enterpriseApSyslogServerEntry row .1.3.6.1.4.1.14823.2.3.2.13.4.1

An entry in the table, containing information
about configuration of one syslog server of the AP.

Indexes

enterpriseApSyslogServerIndex

Column	Syntax	OID
enterpriseApSyslogServerIndex Index of the Syslog Server	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.13.4.1.1
enterpriseApSyslogServerState This value indicates whether the syslog server is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.13.4.1.2
enterpriseApSyslogServerIPAddress This value indicates the IP address of the syslog server.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.14823.2.3.2.13.4.1.3
enterpriseApSyslogServerPort This value indicates the UDP Port used by the syslog server.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.14823.2.3.2.13.4.1.4

Table of descriptive and status information about
configuration of each radio in terms of security settings.

enterpriseApSecurityEntry row .1.3.6.1.4.1.14823.2.3.2.14.1.1

An entry in the table, containing information
about configuration of one radio of the AP.

Indexes

enterpriseApSecurityIndex

Column	Syntax	OID
enterpriseApSecurityIndex Radio Index for security settings.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.14.1.1.1
enterpriseApSecuritySharedKeyLen This value indicates the shared key length for this radio interface.	Enumeration Enumerated Values: 0 none 1 sixtyFour 2 oneHundredTwentyEight 3 oneHundredFiftyTwo	.1.3.6.1.4.1.14823.2.3.2.14.1.1.3
enterpriseApSecurityWPAMode This value indicates the state of WPA for this radio interface.	Enumerationr/w Enumerated Values: 0 supported 1 required 2 disabled	.1.3.6.1.4.1.14823.2.3.2.14.1.1.4
enterpriseApSecurityWPAKeyType This value indicates the type of WPA Key Management in use for this radio interface.	Enumerationr/w Enumerated Values: 0 dot1x 1 presharedkey	.1.3.6.1.4.1.14823.2.3.2.14.1.1.5
enterpriseApSecurityWPACipherobsolete This value indicates the type of WPA Cipher in use for this radio interface.	Enumerationr/w Enumerated Values: 0 wep 1 tkip 2 aes	.1.3.6.1.4.1.14823.2.3.2.14.1.1.6
enterpriseApSecurityWPAPSKType This value indicates the type of WPA Pre Shared Key in use for this radio interface.	Enumerationr/w Enumerated Values: 0 hex 1 alphanumeric	.1.3.6.1.4.1.14823.2.3.2.14.1.1.7
enterpriseApSecurityWPAPSK This value indicates WPA Pre Shared Key in use for this radio interface.	OctetStringr/w Constraints: range: 0-80	.1.3.6.1.4.1.14823.2.3.2.14.1.1.8
enterpriseApSecurityWEPKeyType This value indicates the type of WEP Key in use for this radio interface.	Enumerationr/w Enumerated Values: 0 hexadecimal 1 alphanumeric	.1.3.6.1.4.1.14823.2.3.2.14.1.1.9
enterpriseApSecurityWEPEnabled This value indicates whether WEP is enabled.	TruthValuer/w Type Values: 1 true 2 false	.1.3.6.1.4.1.14823.2.3.2.14.1.1.10
enterpriseApSecurityWPACipherSuite This value indicates the type of WPA Cipher Suite in use for this radio interface.	Enumerationr/w Enumerated Values: 0 aes-ccmp 1 tkip 2 wep	.1.3.6.1.4.1.14823.2.3.2.14.1.1.11
enterpriseApSecurityWPAPreAuthentication Whether Pre-Authentication is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.14.1.1.12
enterpriseApSecurityWPAPmksaLifetime The number (in minutes) for Pmksa-Lifetime.	Integer32r/w Constraints: range: 0-14400	.1.3.6.1.4.1.14823.2.3.2.14.1.1.13

Table of descriptive and status information about
configuration of each radio.

enterpriseApRadioEntry row .1.3.6.1.4.1.14823.2.3.2.15.1.1

An entry in the table, containing information
about configuration of one radio of the AP.

Indexes

enterpriseApRadioIndex

Column	Syntax	OID
enterpriseApRadioIndex Radio Index for configuration.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.15.1.1.1
enterpriseApRadioStateobsolete This value indicates the state of the radio interface.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.15.1.1.2
enterpriseApRadioAutoChannel This value indicates whether auto channel selection is enabled or not for this radio interface	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.15.1.1.3
enterpriseApRadioTransmitPower This value indicates the transmit power for this radio interface.	Enumerationr/w Enumerated Values: 0 min 1 eighth 2 quarter 3 half 4 full	.1.3.6.1.4.1.14823.2.3.2.15.1.1.4
enterpriseApRadioClosedSystemobsolete This value indicates whether closed system is enabled for this radio interface.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.15.1.1.5
enterpriseApRadioMaxAssocobsolete This value indicates the max number of clients allowed on this radio interface.	Integer32r/w Constraints: range: 1-64	.1.3.6.1.4.1.14823.2.3.2.15.1.1.6
enterpriseApRadioTransmitKeyobsolete This value indicates default transmit key in use for this radio interface.	Integer32r/w Constraints: range: 1-4	.1.3.6.1.4.1.14823.2.3.2.15.1.1.7
enterpriseApRadioTurboMode This value indicates whether turbo mode is enabled for this radio interface.	Enumerationr/w Enumerated Values: 1 disabled 2 static-turbo 3 dynamic-turbo	.1.3.6.1.4.1.14823.2.3.2.15.1.1.8
enterpriseApRadioDescriptionobsolete This value indicates the description for this radio interface.	OctetStringr/w Constraints: range: 0-80	.1.3.6.1.4.1.14823.2.3.2.15.1.1.9
enterpriseApRadioDataRate This value indicates the data rate for this radio interface. Radio interface A operates at 6, 9, 12, 18, 24, 36, 48, 54. Radio interface G operates all listed data rates. The auto setting will attempt to set the best …	Enumerationr/w Enumerated Values: 1 oneMbps 2 twoMbps 5 fiveAndHalfMbps 6 sixMbps 9 nineMbps 11 elevenMbps 12 twelveMbps 18 eighteenMbps 24 twentyFourMbps 36 thirtySixMbps 48 fourtyEightMbps 54 fiftyFourMbps 255 auto	.1.3.6.1.4.1.14823.2.3.2.15.1.1.10
enterpriseApRadioGMode This value indicates the radio mode for the 802.11g radio. This setting is only valid for the 802.11g interface.	Enumerationr/w Enumerated Values: 1 bOnly 2 gOnly 3 bg	.1.3.6.1.4.1.14823.2.3.2.15.1.1.11
enterpriseApRadioAntennaMode This value indicates the antenna mode in use for the G-radio. The values are interpreted as follows: fixed(1) means use both built-in antennas, external(2) means use one external antenna on the right side. This setti…	Enumerationr/w Enumerated Values: 1 fixed 2 external	.1.3.6.1.4.1.14823.2.3.2.15.1.1.12
enterpriseApRadioAntennaId	DisplayString	.1.3.6.1.4.1.14823.2.3.2.15.1.1.13
enterpriseApRadioRogueApDetection The status of Rogue AP detection for each index. enabled(1) To set rogue Ap detection enabled. disabled(2) To set rogue Ap detection disabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.15.1.1.16
enterpriseApRadioRogueApScanInterval This value indicates the interval between each rogue AP scan.(unit: minutes)	Integer32r/w Constraints: range: 30-10080	.1.3.6.1.4.1.14823.2.3.2.15.1.1.17
enterpriseApRadioRogueApScanDuration This value indicates the rogue AP scan duratoin.(unit: minutes)	Integer32r/w Constraints: range: 100-1000	.1.3.6.1.4.1.14823.2.3.2.15.1.1.18
enterpriseApRadioRogueApScanNow To force Ap to do rogue AP scan right away. enabled(1) To do Rogue AP scan right now. disabled(2) To set rogue Ap.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.15.1.1.19
enterpriseApRadioMICMode This value indicates the MIC mode status for this radio index. software(1) To set MIC mode to software. hardware(2) To set MIC mode to hardware.	Enumerationr/w Enumerated Values: 1 software 2 hardware	.1.3.6.1.4.1.14823.2.3.2.15.1.1.21
enterpriseApRadioSuperMode This value indicates the super mode status for this radio index. enabled (1) To set super mode enabled. disabled(2) To set super mode disabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.15.1.1.22
enterpriseApRadioBeaconInterval This value indicates the beacon interval for this radio index.	Integer32r/w Constraints: range: 20-1000	.1.3.6.1.4.1.14823.2.3.2.15.1.1.23
enterpriseApRadioDataBeaconRate This value indicates the data beacon rate for the radio index.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.15.1.1.24
enterpriseApRadioChannel This valud indicates the radio channel for the radio index. set channel 42/50/58/152/160 for static turbo mode, set channel 40/48/56/153/161 for dynamic turbo mode, set channel 36/40/44/48/52/56/60/64/149/153/157/161/16…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.15.1.1.25
enterpriseApRadioFragmentLength This value indicates the fragment length for the radio index.(unit: Byte)	Integer32r/w Constraints: range: 256-2346	.1.3.6.1.4.1.14823.2.3.2.15.1.1.26
enterpriseApRadioRTSThreshold This value indicates the RTS Threshold for the radio index.(unit: Byte)	Integer32r/w Constraints: range: 0-2347	.1.3.6.1.4.1.14823.2.3.2.15.1.1.27
enterpriseApRadioAntennaGainReduction This value indicates the antenna gain reduction for the radio index.(unit: dB)	Integer32r/w Constraints: range: 0-29	.1.3.6.1.4.1.14823.2.3.2.15.1.1.28

Table of descriptive and status information about
configuration of each trap receiving server.

enterpriseApSNMPTrapDestinationEntry row .1.3.6.1.4.1.14823.2.3.2.16.3.1

An entry in the table, containing information
about configuration of one trap receiving server.

Indexes

enterpriseApSNMPTrapDestinationIndex

Column	Syntax	OID
enterpriseApSNMPTrapDestinationIndex Index of the Trap Destination Table.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.14823.2.3.2.16.3.1.1
enterpriseApSNMPTrapDestinationCommunity The SNMP Trap Community	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.14823.2.3.2.16.3.1.2
enterpriseApSNMPTrapDestinationIP The IP address of the trap receiving server.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.14823.2.3.2.16.3.1.3
enterpriseApSNMPTrapDestinationState This value indicates whether the trap receiving server is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.16.3.1.4

This table list all sessions (wireless stations) status

enterpriseApSessionEntry row .1.3.6.1.4.1.14823.2.3.2.17.1.1

An entry in the table, containing information
about status and statistics of the wireless station.

Indexes

enterpriseApSessionIfIndex enterpriseApSessionStationAddres

Column	Syntax	OID
enterpriseApSessionIfIndex Interface index for the radio this session is associated with.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.17.1.1.1
enterpriseApSessionStationAddres The unique MAC Address of the station for this session.	MacAddress Type Constraints: range: 6	.1.3.6.1.4.1.14823.2.3.2.17.1.1.2
enterpriseApSessionAuthenticated Whether the session is authenticated or not.	TruthValue Type Values: 1 true 2 false	.1.3.6.1.4.1.14823.2.3.2.17.1.1.3
enterpriseApSessionAssociated Whether the session is associated or not. It is rare case that not associated stations show up in the table.	TruthValue Type Values: 1 true 2 false	.1.3.6.1.4.1.14823.2.3.2.17.1.1.4
enterpriseApSessionIsForwarding Whether the AP is forwarding the client station traffic (higher level authentication)	TruthValue Type Values: 1 true 2 false	.1.3.6.1.4.1.14823.2.3.2.17.1.1.5
enterpriseApSessionKeyType The encryption key type used by the station. Note that wpa-wep is not supported	Enumeration Enumerated Values: 1 none 2 staticWep 3 dynamicWep 4 wpaWep 5 wpaTkip 6 wpaAes	.1.3.6.1.4.1.14823.2.3.2.17.1.1.6
enterpriseApSessionAssociationId The internal association identify number	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.17.1.1.7
enterpriseApSessionLastAuthenticatedTime This is the time in hundredths of a second last time the client is authenticated. Note that a session may be authenticated multiple times. The value is related to the system startup	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.14823.2.3.2.17.1.1.8
enterpriseApSessionAssociatedTime This is the time in hundredths of a second since the client associated. The value is related to the system startup	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.14823.2.3.2.17.1.1.9
enterpriseApSessionLastAssociatedTime This is the time in hundredths of a second when the client associated in last session. The value is related to the system startup	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.14823.2.3.2.17.1.1.10
enterpriseApSessionLastDisassociatedTime This is the time in hundredths of a second when the client disassociated in last session. The value is related to the system startup	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.14823.2.3.2.17.1.1.11
enterpriseApSessionTxPacketCount This is the number of packets transmitted from the client to the AP. It includes data, control and management packets.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.14823.2.3.2.17.1.1.12
enterpriseApSessionRxPacketCount This is the number of unicast packets transmitted from the AP to the client. It includes data, control and management packets.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.14823.2.3.2.17.1.1.13
enterpriseApSessionTxByteCount This is the number of bytes transmitted from the client to the AP. It includes the bytes of data, control and management packets.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.14823.2.3.2.17.1.1.14
enterpriseApSessionRxByteCount This is the number of unicast bytes transmitted from the AP to the client. It includes the bytes of data, control and management packets.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.14823.2.3.2.17.1.1.15

Table of descriptive and status information about
configuration of each radio.

enterpriseAPVapRadioEntry row .1.3.6.1.4.1.14823.2.3.2.20.1.1

An entry in the table, containing information
about configuration of one radio of the AP.

Indexes

enterpriseAPVapRadioIndex

Column	Syntax	OID
enterpriseAPVapRadioIndex Radio Index for configuration.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.20.1.1.1
enterpriseAPVapRadioState This value indicates the state of the radio interface.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.20.1.1.2
enterpriseAPVapRadioClosedSystem This value indicates whether closed system is enabled for this radio interface.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.20.1.1.3
enterpriseAPVapRadioMaxAssoc This value indicates the max number of clients allowed on this radio interface.	Integer32r/w Constraints: range: 1-64	.1.3.6.1.4.1.14823.2.3.2.20.1.1.4
enterpriseAPVapRadioTransmitKey This value indicates default transmit key in use for this radio interface.	Integer32r/w Constraints: range: 1-4	.1.3.6.1.4.1.14823.2.3.2.20.1.1.5
enterpriseAPVapRadioDescription This value indicates the description for this radio interface.	OctetStringr/w Constraints: range: 0-80	.1.3.6.1.4.1.14823.2.3.2.20.1.1.6
enterpriseAPVapRadioAuthTimeoutInterval This value indicates the Authentication Timeout interval for this radio interface.	Integer32r/w Constraints: range: 5-60	.1.3.6.1.4.1.14823.2.3.2.20.1.1.8
enterpriseAPVapRadioAssocTimeoutInterval This value indicates the Association Timeout interval for this radio interface.	Integer32r/w Constraints: range: 0-9 range: 5-60	.1.3.6.1.4.1.14823.2.3.2.20.1.1.9
enterpriseAPVapRadioWPA2PMKSALifeTime This value indicates the WPA2 PMSA Life Time for this radio interface.	Integer32r/w Constraints: range: 1-20 range: 1-1440	.1.3.6.1.4.1.14823.2.3.2.20.1.1.10

Table of configuration information for Wds for each
Radio interface.

enterpriseApRadioWdsEntry row .1.3.6.1.4.1.14823.2.3.2.22.1.1

An entry in the table, containing information
about configuration of peer Bridging
for one radio of the AP. The table is indexed by radio
Index (corresponding to enterpriseApRadioTable). The table does not contain …

Indexes

enterpriseApRadioIndex

Column	Syntax	OID
wdsApRole This value indicates the role of the Ap for this radio, roleAp(1): AP operation. roleBridgeMaster(2): Root-Bridge mode. roleBridge(4): Bridge Mode. relay wireless traffic.	Enumerationr/w Enumerated Values: 1 roleAp 2 roleBridgeMaster 4 roleBridge	.1.3.6.1.4.1.14823.2.3.2.22.1.1.1
wdsChannelAutoSync This value indicates the states of channel auto synchronize for this radio.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.22.1.1.3
wdsMasterSlaveMode This value indicates the Master/Slave mode for this radio. master (1) To set to master mode. slave (2) To set to slave mode.	Enumerationr/w Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.14823.2.3.2.22.1.1.4

Table of configuration information for Wds Peers for each
Radio interface.

enterpriseApRadioWdsPeerEntry row .1.3.6.1.4.1.14823.2.3.2.22.2.1

An entry in the table, containing information
about configuration of peer Bridging
for one radio of the AP. The table is indexed by radio
Index (corresponding to enterpriseApRadioTable) and the peer
index …

Indexes

enterpriseApRadioIndex wdsPeerIndex

Column	Syntax	OID
wdsPeerIndex Peer Index for the radio interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.22.2.1.1
wdsPeerBssid The BSSID for this peer.	OctetStringr/w Constraints: range: 1-6	.1.3.6.1.4.1.14823.2.3.2.22.2.1.2

The table of WMM information for each radio interface.

enterpriseApWMMEntry row .1.3.6.1.4.1.14823.2.3.2.24.1.1

An entry of table, contains the WMM information.

Indexes

enterpriseApWMMModeIndex

Column	Syntax	OID
enterpriseApWMMModeIndex Peer Index for the radio interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.24.1.1.1
enterpriseApWMMMode This value indicates the WMM mode for the radio interface. disabled(1) To set WMM mode disabled. support (2) To set WMM mode supported. required(3) To set WMM mode required.	Enumerationr/w Enumerated Values: 1 disabled 2 support 3 required	.1.3.6.1.4.1.14823.2.3.2.24.1.1.2

The table of WMM Ack Policy information for each ac number on the radio interface.

enterpriseApWMMAckPolicyEntry row .1.3.6.1.4.1.14823.2.3.2.24.2.1

An entry of table, contains the WMM Ack Policy information.

Indexes

enterpriseApWMMAckPolicyIndex

Column	Syntax	OID
enterpriseApWMMAckPolicyIndex The value indicates the AC number for each radio interface. 0 --> AC0 (Best Effect) 1 --> AC1 (Background) 2 --> AC2 (Video) 3 --> AC3 (Voice)	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.24.2.1.1

The table of WMM BSS parameter information.

enterpriseApWMMBSSParamEntry row .1.3.6.1.4.1.14823.2.3.2.24.3.1

An entry of table, contains the WMM BSS parameter information for each ac number on the radio interface.

Indexes

enterpriseApWMMBSSParamIndex

Column	Syntax	OID
enterpriseApWMMBSSParamIndex The value indicates the AC number for each radio interface. 0 --> AC0 (Best Effort) 1 --> AC1 (Background) 2 --> AC2 (Video) 3 --> AC3 (Voice)	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.24.3.1.1
enterpriseApWMMBSSParamLogCwMin This value indicates the WMM BSS parameter logCwMin of AC number for the radio interface.	Integer32r/w Constraints: range: 1-15	.1.3.6.1.4.1.14823.2.3.2.24.3.1.2
enterpriseApWMMBSSParamLogCwMax This value indicates the WMM BSS parameter logCwMax of each AC number for the radio interface.	Integer32r/w Constraints: range: 1-15	.1.3.6.1.4.1.14823.2.3.2.24.3.1.3
enterpriseApWMMBSSParamAIFSN This value indicates the WMM BSS parameters AIFSN of each AC number for the radio interface.	Integer32r/w Constraints: range: 1-15	.1.3.6.1.4.1.14823.2.3.2.24.3.1.4
enterpriseApWMMBSSParamTXOPLimit This value indicates the WMM BSS parameters TXOP Limit of each AC number for the radio interface.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.14823.2.3.2.24.3.1.5
enterpriseApWMMBSSParamAdmissionCtrl This value indicates the BSS parameters Admission Control of each AC number for the radio interface.	Enumerationr/w Enumerated Values: 1 ebabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.24.3.1.6

The table of configuration information for WMM AP parameters for each ac number on the radio interface.

enterpriseApWMMAPParamEntry row .1.3.6.1.4.1.14823.2.3.2.24.4.1

An entry table, include the Ap parameter information for each ac numbers.

Indexes

enterpriseApWMMAPParamIndex

Column	Syntax	OID
enterpriseApWMMAPParamIndex The value indicates the AC number for each radio interface. 0 --> AC0 (Best Effort) 1 --> AC1 (Background) 2 --> AC2 (Video) 3 --> AC3 (Voice)	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.24.4.1.1
enterpriseApWMMAPParamLogCwMin This value indicates the LogCwMin of AP parameter for each AC number on the radio interface.	Integer32r/w Constraints: range: 1-15	.1.3.6.1.4.1.14823.2.3.2.24.4.1.2
enterpriseApWMMAPParamLogCwMax This value indicates the LogCwMax of AP parameter for each AC number on the radio interface.	Integer32r/w Constraints: range: 1-15	.1.3.6.1.4.1.14823.2.3.2.24.4.1.3
enterpriseApWMMAPParamAIFSN This value indicates the AIFSN of AP parameter for each AC number on the radio interface.	Integer32r/w Constraints: range: 1-15	.1.3.6.1.4.1.14823.2.3.2.24.4.1.4
enterpriseApWMMAPParamTXOPLimit This value indicates the TXOP Limit of AP parameter for each AC number on the radio interface.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.14823.2.3.2.24.4.1.5
enterpriseApWMMAPParamAdmissionCtrl This value indicates the admission control of AP parameter for each AC number on the radio interface.	Enumerationr/w Enumerated Values: 1 ebabled 2 disabled	.1.3.6.1.4.1.14823.2.3.2.24.4.1.6

The table of STP link Path Cost and link port priority information for each nodes on radio interface.

enterpriseApSTPNodeEntry row .1.3.6.1.4.1.14823.2.3.2.25.6.1.1

An entry in a table, contain the link path cost and link port priroity information.

Indexes

enterpriseApSTPNodeIndex

Column	Syntax	OID
enterpriseApSTPNodeIndex Peer Index for the nodes on the radio interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.14823.2.3.2.25.6.1.1.1
enterpriseApSTPNodeLinkPathCost This value indicates the link path cost for the node on this radio interface.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.14823.2.3.2.25.6.1.1.2
enterpriseApSTPNodeLinkPortPriority This value indicates the link path cost for the node on this radio interface.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.14823.2.3.2.25.6.1.1.3