ADTRAN-GENVDSL2-LINE-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
27
Rows
27
Columns
542

adGenVdsl2LineConfProfileTable

table
.1.3.6.1.4.1.664.5.65.1.1.1 · 1 row entry · 116 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2LineConfProfileTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2LineConfProfileTable' 
This table contains information on the VDSL2 line
configuration.  One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL2 line.
adGenVdsl2LineConfProfileEntry row .1.3.6.1.4.1.664.5.65.1.1.1.1
Each entry consists of a list of parameters that
represents the configuration of an VDSL2 modem.

`Static' profiles - profiles are automaticly
created or destroyed as VDSL2 physical lines
are discovered a…
Indexes
Column Syntax OID
adGenVdsl2LineConfProfileName
This object is used by the line configuration table
in order to identify a row of this table.

This value cannot be user-specified and is not dynamic.

There is a one-to-one relationship betw…
OctetString
Constraints:
range: 1-10
 .1.3.6.1.4.1.664.5.65.1.1.1.1.1
adGenVdsl2ConfDsRateMode
Defines what form of downstream rate adaptation is
configured on this modem.
Enumerationr/w
Enumerated Values:
1fixed
2adaptAtStartup
3adaptAtRuntime
 .1.3.6.1.4.1.664.5.65.1.1.1.1.2
adGenVdsl2ConfDsTargetSnrMgn
Configured Target Signal/Noise Margin. This is the noise
margin the modem must achieve with the target BER (10-7)
or better to successfully complete initialization. The
noise margin ranges from 0 to 31 dB with 0.1 dB …
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.3
adGenVdsl2ConfDsMaxSnrMgn
Configured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation. The noise margin ranges from 0 to 31 dB
with 0.1 dB st…
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.4
adGenVdsl2ConfDsMinSnrMgn
Configured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output. If that
is not possible the modem will attempt to re-initialize
or s…
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.5
adGenVdsl2ConfUsTargetSnrMgn
Configured Target Signal/Noise Margin. This is the noise
margin the modem must achieve with the target BER (10-7)
or better to successfully complete initialization. The
noise margin ranges from 0 to 31 dB with 0.1 dB …
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.6
adGenVdsl2ConfUsMaxSnrMgn
Configured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation. The noise margin ranges from 0 to 31 dB
with 0.1 dB st…
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.7
adGenVdsl2ConfUsMinSnrMgn
Configured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output. If that
is not possible the modem will attempt to re-initialize
or s…
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.8
adGenVdsl2LineConfProfileRowStatus
This object is used to create a new row or modify or
delete an existing row in this table.

A profile activated by setting this object to
`active'. When `active' is set, the system
will validate the profi…
SNMPv2-TCRowStatus
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.664.5.65.1.1.1.1.9
adGenVdsl2ConfServiceMode
The configuration parameter sets the modem service mode.
Enumerationr/w
Enumerated Values:
1multiMode
2t1413
3gDMT
4gLite
5g9923
6g9924
7g9925
8readsl
9adsl1MultiMode
10g9925AnxM
11g9931
12g9932
13vdsl2MultiMode
14vdsl2PtmFallback
255tseMultimode
 .1.3.6.1.4.1.664.5.65.1.1.1.1.10
adGenVdsl2ConfMultiModeDmtTse
Multimode DMT Transmission System Enabling (XTSE). A list of the
different modulation types enabled in this profile for multimode.
It is coded in a bit-map representation with 1 or more bits set.
A bit set to '1' mean…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.1.1.11
adGenVdsl2ConfBandProfiles
Bit-map of ITU-T G.993.2 implementation profiles supported by
an VTU-x and can be provisioned on the VDSL2 line.

Bit Assignments:
Bit 00: Profile 8A
Bit 01: Profile 8B
Bit …
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.1.1.12
adGenVdsl2ConfSpecificPsdSelect
The VDSL2 specific PSD selections to be used in the upstream
and downstream directions. The validity of these selections
is dependent of the VDSL2 band profile selection.
Enumerationr/w
Enumerated Values:
21vdsl1-ansi-fttcab-m1
22vdsl1-ansi-fttcab-m2
23vdsl1-ansi-fttex-m1
24vdsl1-ansi-fttex-m2
41vdsl1-etsi-fttcab-pcab-m1
42vdsl1-etsi-fttcab-pcab-m2
43vdsl1-etsi-fttex-p1-m1-o-isdn
44vdsl1-etsi-fttex-p1-m2-o-isdn
45vdsl1-etsi-fttex-p2-m1-o-pots
46vdsl1-etsi-fttex-p2-m2-o-pots
101vdsl2-a-m1-eu32
102vdsl2-a-m2-eu36
103vdsl2-a-m3-eu40
104vdsl2-a-m4-eu44
105vdsl2-a-m5-eu48
106vdsl2-a-m6-eu52
107vdsl2-a-m7-eu56
108vdsl2-a-m8-eu60
109vdsl2-a-m9-eu64
110vdsl2-a-eu128
121vdsl2-a-m1-998-35b-eu32
129vdsl2-a-m9-998-35b-eu64
201vdsl2-a-m1-adlu32
202vdsl2-a-m2-adlu36
203vdsl2-a-m3-adlu40
204vdsl2-a-m4-adlu44
205vdsl2-a-m5-adlu48
206vdsl2-a-m6-adlu52
207vdsl2-a-m7-adlu56
208vdsl2-a-m8-adlu60
209vdsl2-a-m9-adlu64
210vdsl2-a-adlu128
301vdsl2-b7-1-997-m1c-a-7
302vdsl2-b7-2-997-m1x-m-8
303vdsl2-b7-3-997-m1x-m
304vdsl2-b7-4-997-m2x-m-8
305vdsl2-b7-5-997-m2x-a
306vdsl2-b7-6-997-m2x-m
307vdsl2-b7-7-hpe17-m1-nus0
308vdsl2-b7-8-hpe30-m1-nus0
309vdsl2-b7-9-997e17-m2x-nus0
310vdsl2-b7-10-997e30-m2x-nus0
401vdsl2-b8-1-998-m1x-a
402vdsl2-b8-2-998-m1x-b
403vdsl2-b8-3-998-m1x-nus0
404vdsl2-b8-4-998-m2x-a
405vdsl2-b8-5-998-m2x-m
406vdsl2-b8-6-998-m2x-b
407vdsl2-b8-7-998-m2x-nus0
408vdsl2-b8-8-998e17-m2x-nus0
409vdsl2-b8-9-998e17-m2x-nus0-m
410vdsl2-b8-10-998ade17-m2x-nus0-m
411vdsl2-b8-11-998ade17-m2x-a
412vdsl2-b8-12-998ade17-m2x-b
413vdsl2-b8-13-998e30-m2x-nus0
414vdsl2-b8-14-998e30-m2x-nus0-m
415vdsl2-b8-15-998ade30-m2x-nus0-m
416vdsl2-b8-16-998ade30-m2x-nus0-a
419vdsl2-b8-19-998e35-m2x-a
420vdsl2-b8-20-998ade35-m2x-a
421vdsl2-b8-21-998ade35-m2x-b
422vdsl2-b8-22-998ade35-m2x-m
431vdsl2-b8-998ade17-m2x-m
432vdsl2-b8-998e17-m2x-a
501vdsl2-c-fttcab-a
502vdsl2-c-fttcab-m
503vdsl2-c-fttex-a
504vdsl2-c-fttex-m
505vdsl2-c-o-adsl
506vdsl2-c-o-tcmisdn
601vdsl2-c-anfp
 .1.3.6.1.4.1.664.5.65.1.1.1.1.13
adGenVdsl2ConfUsPsdMaskU0Select
Enable or disable of the use of the VDSL2 U0 band in the
upstream direction. U0 is a relatively small frequency band
of operation used by ADSL2+/ADSL2/ADSL modems. It is optional
depending on the selected band profile…
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.5.65.1.1.1.1.14
adGenVdsl2ConfUsTrellis
Enable or disable Upstream Trellis Encoding.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.5.65.1.1.1.1.15
adGenVdsl2ConfDsTrellis
Enable or disable Downstream Trellis Encoding.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.5.65.1.1.1.1.16
adGenVdsl2ConfUsPboSetting
Defines the Upstream Power Backoff mode setting.
Enumerationr/w
Enumerated Values:
0pboOff
1pboEnvA
2pboEnvB
3pboEnvC
4pboEnvD
5pboEnvE
6pboEnvF
7pboANFP
254pboAuto
255pboCustom
 .1.3.6.1.4.1.664.5.65.1.1.1.1.17
adGenVdsl2ConfDsPboSetting
Defines the Downstream Power Backoff mode setting.
Enumerationr/w
Enumerated Values:
0pboOff
1pboEnvA
2pboEnvB
3pboEnvC
4pboEnvD
5pboEnvE
6pboEnvF
7pboANFP
254pboAuto
255pboCustom
 .1.3.6.1.4.1.664.5.65.1.1.1.1.18
adGenVdsl2ConfUsVnoiseSetting
Defines upstream virtual noise setting.
Enumerationr/w
Enumerated Values:
0off
1low
2med
3high
254auto
255custom
 .1.3.6.1.4.1.664.5.65.1.1.1.1.19
adGenVdsl2ConfDsVnoiseSetting
Defines downstream virtual noise setting.
Enumerationr/w
Enumerated Values:
0off
1low
2med
3high
254auto
255custom
 .1.3.6.1.4.1.664.5.65.1.1.1.1.20
adGenVdsl2ConfUsBitSwap
Defines upstream Bit Swap to be enabled or not.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.5.65.1.1.1.1.21
adGenVdsl2ConfDsBitSwap
Defines downstream Bit Swap to be enabled or not.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.5.65.1.1.1.1.22
adGenVdsl2ConfHamBandNotches
A bit-map of transmit power spectral density mask code, used
to avoid interference with HAM (Handheld Amateur Radio)
radio bands by introducing power control (notching) in one
or more of these bands. A bit set indicates…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.1.1.23
adGenVdsl2ConfUsNomAggTxPwr
The maximum nominal aggregate transmit power in the upstream
direction during initialization and Showtime. It ranges from
0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.664.5.65.1.1.1.1.24
adGenVdsl2ConfDsNomAggTxPwr
The maximum nominal aggregate transmit power in the
downstream direction during initialization and Showtime. It
ranges from 0 to 255 units of 0.1 dBm (physical values are 0
to 25.5 dBm).
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.5.65.1.1.1.1.25
adGenVdsl2ConfUsMaxNomTxPsd
This parameter represents the maximum nominal transmit PSD in
the upstream direction during initialization and showtime
(in dBm/Hz). It ranges from -60 to -30 dBm/Hz, with 0.1 dB steps
(-600..-300).
Integer32r/w
Constraints:
range: -600-300
 .1.3.6.1.4.1.664.5.65.1.1.1.1.26
adGenVdsl2ConfDsMaxNomTxPsd
This parameter represents the maximum nominal transmit PSD in
the downstream direction during initialization and showtime
(in dBm/Hz). It ranges from -60 to -30 dBm/Hz, with 0.1 dB steps
(-600..-300).
Integer32r/w
Constraints:
range: -600-300
 .1.3.6.1.4.1.664.5.65.1.1.1.1.27
adGenVdsl2ConfUsMaxAggRxPwr
The maximum upstream aggregate receive power over the relevant
set of sub-carriers. The xTU-C should verify that the
upstream power cutback is such that this maximum aggregate
receive power value is honored. It ranges…
Integer32r/w
Constraints:
range: -255-255
 .1.3.6.1.4.1.664.5.65.1.1.1.1.28
adGenVdsl2ConfFramingMode
This is the PMS-TC layer Framing mode setting.
Enumerationr/w
Enumerated Values:
0auto
1atm
2efm
3hdlc
 .1.3.6.1.4.1.664.5.65.1.1.1.1.29
adGenVdsl2ConfUsLp0MaxPayloadRate
Latency Path 0 upstream maximum payload data rate.
bpsUnsigned32r/w
Constraints:
range: 0-96000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.30
adGenVdsl2ConfUsLp0MinPayloadRate
Latency Path 0 upstream minimum payload data rate.
bpsUnsigned32r/w
Constraints:
range: 0-96000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.31
adGenVdsl2ConfUsLp0MaxDelay
Latency Path 0 upstream maximum Interleave Delay.
This parameter is the maximum one-way interleaving delay
in milli-seconds introduced by the PMS-TC between the
alfa and the beta reference points, in the direction of
th…
msecUnsigned32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.32
adGenVdsl2ConfUsLp0MinProtection
Latency Path 0 upstream Minimum Impulse Noise Protection.
This parameter specifies the minimum impulse noise
protection for the latency path in 0.5 fractions of DMT
symbols. A value of 0 indicates no minimum bound.
0.5 SymUnsigned32r/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.664.5.65.1.1.1.1.33
adGenVdsl2ConfUsLp0RaRatio
This parameter (expressed in %) specifies the ratio that
should be taken into account for the latency path when
performing rate adaptation in the direction of the
channel. The ratio is defined as a percentage in the
0 t…
%Integer32r/w
Constraints:
range: 0-100
 .1.3.6.1.4.1.664.5.65.1.1.1.1.34
adGenVdsl2ConfUsLp0InitPolicy
Selects the US latency path 0 channel framing parameter
policy during initialization. The options are to
maximize net data rate (ndr) or impulse noise
protection (inp).
Enumerationr/w
Enumerated Values:
0ndr
1inp
 .1.3.6.1.4.1.664.5.65.1.1.1.1.35
adGenVdsl2ConfDsLp0MaxPayloadRate
Latency Path 0 downstream maximum payload data rate.
bpsUnsigned32r/w
Constraints:
range: 0-350000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.36
adGenVdsl2ConfDsLp0MinPayloadRate
Latency Path 0 downstream minimum payload data rate.
bpsUnsigned32r/w
Constraints:
range: 0-350000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.37
adGenVdsl2ConfDsLp0MaxDelay
Latency Path 0 downstream maximum Interleave Delay.
This parameter is the maximum one-way interleaving delay
in milli-seconds introduced by the PMS-TC between the
alfa and the beta reference points, in the direction of
…
msecUnsigned32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.38
adGenVdsl2ConfDsLp0MinProtection
Latency Path 0 downstream Minimum Impulse Noise Protection.
This parameter specifies the minimum impulse noise
protection for the latency path in 0.5 fractions of DMT
symbols. A value of 0 indicates no minimum bound.
0.5 SymUnsigned32r/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.664.5.65.1.1.1.1.39
adGenVdsl2ConfDsLp0RaRatio
This parameter (expressed in %) specifies the ratio that
should be taken into account for the latency path when
performing rate adaptation in the direction of the
channel. The ratio is defined as a percentage in the
0 t…
%Integer32r/w
Constraints:
range: 0-100
 .1.3.6.1.4.1.664.5.65.1.1.1.1.40
adGenVdsl2ConfDsLp0InitPolicy
Selects the DS latency path 0 channel framing parameter
policy during initialization. The options are to
maximize net data rate (ndr) or impulse noise
protection (inp).
Enumerationr/w
Enumerated Values:
0ndr
1inp
 .1.3.6.1.4.1.664.5.65.1.1.1.1.41
adGenVdsl2ConfUsLp1MaxPayloadRate
Latency Path 1 upstream maximum payload data rate.
bpsUnsigned32r/w
Constraints:
range: 0-96000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.42
adGenVdsl2ConfUsLp1MinPayloadRate
Latency Path 1 upstream minimum payload data rate.
bpsUnsigned32r/w
Constraints:
range: 0-96000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.43
adGenVdsl2ConfUsLp1MaxDelay
Latency Path 1 upstream maximum Interleave Delay.
This parameter is the maximum one-way interleaving delay
in milli-seconds introduced by the PMS-TC between the
alfa and the beta reference points, in the direction of
th…
msecUnsigned32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.44
adGenVdsl2ConfUsLp1MinProtection
Latency Path 1 upstream Minimum Impulse Noise Protection.
This parameter specifies the minimum impulse noise
protection for the latency path in 0.5 fractions of DMT
symbols. A value of 0 indicates no minimum bound.
0.5 SymUnsigned32r/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.664.5.65.1.1.1.1.45
adGenVdsl2ConfUsLp1RaRatio
This parameter (expressed in %) specifies the ratio that
should be taken into account for the latency path when
performing rate adaptation in the direction of the
channel. The ratio is defined as a percentage in the
0 t…
%Integer32r/w
Constraints:
range: 0-100
 .1.3.6.1.4.1.664.5.65.1.1.1.1.46
adGenVdsl2ConfUsLp1InitPolicy
Selects the US latency path 1 channel framing parameter
policy during initialization. The options are to
maximize net data rate (ndr) or impulse noise
protection (inp).
Enumerationr/w
Enumerated Values:
0ndr
1inp
 .1.3.6.1.4.1.664.5.65.1.1.1.1.47
adGenVdsl2ConfDsLp1MaxPayloadRate
Latency Path 1 downstream maximum payload data rate.
bpsUnsigned32r/w
Constraints:
range: 0-350000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.48
adGenVdsl2ConfDsLp1MinPayloadRate
Latency Path 1 downstream minimum payload data rate.
bpsUnsigned32r/w
Constraints:
range: 0-350000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.49
adGenVdsl2ConfDsLp1MaxDelay
Latency Path 1 downstream maximum Interleave Delay.
This parameter is the maximum one-way interleaving delay
in milli-seconds introduced by the PMS-TC between the
alfa and the beta reference points, in the direction of
…
msecUnsigned32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.50
adGenVdsl2ConfDsLp1MinProtection
Latency Path 1 downstream Minimum Impulse Noise Protection.
This parameter specifies the minimum impulse noise
protection for the latency path in 0.5 fractions of DMT
symbols. A value of 0 indicates no minimum bound.
0.5 SymUnsigned32r/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.664.5.65.1.1.1.1.51
adGenVdsl2ConfDsLp1RaRatio
This parameter (expressed in %) specifies the ratio that
should be taken into account for the latency path when
performing rate adaptation in the direction of the
channel. The ratio is defined as a percentage in the
0 t…
%Integer32r/w
Constraints:
range: 0-100
 .1.3.6.1.4.1.664.5.65.1.1.1.1.52
adGenVdsl2ConfDsLp1InitPolicy
Selects the DS latency path 1 channel framing parameter
policy during initialization. The options are to
maximize net data rate (ndr) or impulse noise
protection (inp).
Enumerationr/w
Enumerated Values:
0ndr
1inp
 .1.3.6.1.4.1.664.5.65.1.1.1.1.53
adGenVdsl2ConfUsLp0Type
Selects the US latency path 0 channel type options.
Enumerationr/w
Enumerated Values:
1noChannel
2fastOnly
3interleavedOnly
 .1.3.6.1.4.1.664.5.65.1.1.1.1.54
adGenVdsl2ConfDsLp0Type
Selects the DS latency path 0 channel type options.
Enumerationr/w
Enumerated Values:
1noChannel
2fastOnly
3interleavedOnly
 .1.3.6.1.4.1.664.5.65.1.1.1.1.55
adGenVdsl2ConfUsLp1Type
Selects the US latency path 1 channel type options.
Enumerationr/w
Enumerated Values:
1noChannel
2fastOnly
3interleavedOnly
 .1.3.6.1.4.1.664.5.65.1.1.1.1.56
adGenVdsl2ConfDsLp1Type
Selects the DS latency path 1 channel type options.
Enumerationr/w
Enumerated Values:
1noChannel
2fastOnly
3interleavedOnly
 .1.3.6.1.4.1.664.5.65.1.1.1.1.57
adGenVdsl2ConfUsRateMode
Defines what form of upstream rate adaptation is
configured on this modem.
Enumerationr/w
Enumerated Values:
1fixed
2adaptAtStartup
3adaptAtRuntime
 .1.3.6.1.4.1.664.5.65.1.1.1.1.58
adGenVdsl2ConfUsCustomPboElecLenKL
Upstream power back-off electrical length (KL0).
0.1 dBInteger32r/w
Constraints:
range: 0-1280
 .1.3.6.1.4.1.664.5.65.1.1.1.1.59
adGenVdsl2ConfUsCustomPboForceLen
Upstream power back-off force electrical length.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.5.65.1.1.1.1.60
adGenVdsl2ConfUsCustomPboBoostMode
Upstream power back-off boost mode.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.5.65.1.1.1.1.61
adGenVdsl2ConfDsCustomPboElecLen
Downstream G997.1 Exchange side electrical length. only multiples of .5 are valid
0.1 dBInteger32r/w
Constraints:
range: 0-2555
 .1.3.6.1.4.1.664.5.65.1.1.1.1.62
adGenVdsl2ConfDsCustomPboCableA
Downstream G997.1 Exchange side cable parameter A.
scalarInteger32r/w
Constraints:
range: 0-640
 .1.3.6.1.4.1.664.5.65.1.1.1.1.63
adGenVdsl2ConfDsCustomPboCableB
Downstream G997.1 Exchange side cable parameter B.
scalarInteger32r/w
Constraints:
range: 0-640
 .1.3.6.1.4.1.664.5.65.1.1.1.1.64
adGenVdsl2ConfDsCustomPboCableC
Downstream G997.1 Exchange side cable parameter C.
scalarInteger32r/w
Constraints:
range: 0-640
 .1.3.6.1.4.1.664.5.65.1.1.1.1.65
adGenVdsl2ConfDsCustomPboMinSignal
Downstream G997.1 Minimum Usable Signal. only multiples of .5 are valid
0.1 dBInteger32r/w
Constraints:
range: 0-1275
 .1.3.6.1.4.1.664.5.65.1.1.1.1.66
adGenVdsl2ConfDsCustomPboMinFreq
Downstream G997.1 Minimum Power Backoff Frequency
4.3125kHz tonesInteger32r/w
Constraints:
range: 0-2048
 .1.3.6.1.4.1.664.5.65.1.1.1.1.67
adGenVdsl2ConfDsCustomPboMaxFreq
Downstream G997.1 Maximum Power Backoff Frequency
4.3125kHz tonesInteger32r/w
Constraints:
range: 32-4095
 .1.3.6.1.4.1.664.5.65.1.1.1.1.68
adGenVdsl2ConfAnfpCalValue
ANFP loss calibration value
dBInteger32r/w
Constraints:
range: 0-52
 .1.3.6.1.4.1.664.5.65.1.1.1.1.69
adGenVdsl2ConfDsDownshiftSnrMgn
Threshold SNR margin to trigger a downstream downshift.
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.70
adGenVdsl2ConfDsUpshiftSnrMgn
Threshold SNR margin to trigger a downstream upshift.
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.71
adGenVdsl2ConfDsMinUpshiftTime
Minimum configured time that must elapse
between downstream upshifts. A value of 2
indicates a downshift cannot occur unless 2
seconds have elapsed since the previous
downshift.
secondsUnsigned32r/w
Constraints:
range: 0-16383
 .1.3.6.1.4.1.664.5.65.1.1.1.1.72
adGenVdsl2ConfDsMinDownshiftTime
Minimum configured time that must elapse
between downstream downshifts. A value of 2
indicates a downshift cannot occur unless 2
seconds have elapsed since the previous
downshift.
secondsUnsigned32r/w
Constraints:
range: 0-16383
 .1.3.6.1.4.1.664.5.65.1.1.1.1.73
adGenVdsl2ConfUsDownshiftSnrMgn
Threshold SNR margin to trigger a upstream downshift.
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.74
adGenVdsl2ConfUsUpshiftSnrMgn
Threshold SNR margin to trigger a upstream upshift.
tenth dBInteger32r/w
Constraints:
range: 0-310
 .1.3.6.1.4.1.664.5.65.1.1.1.1.75
adGenVdsl2ConfUsMinUpshiftTime
Minimum configured time that must elapse
between upstream upshifts. A value of 2
indicates a downshift cannot occur unless 2
seconds have elapsed since the previous
downshift.
secondsUnsigned32r/w
Constraints:
range: 0-16383
 .1.3.6.1.4.1.664.5.65.1.1.1.1.76
adGenVdsl2ConfUsMinDownshiftTime
Minimum configured time that must elapse
between upstream downshifts. A value of 2
indicates a downshift cannot occur unless 2
seconds have elapsed since the previous
downshift.
secondsUnsigned32r/w
Constraints:
range: 0-16383
 .1.3.6.1.4.1.664.5.65.1.1.1.1.77
adGenVdsl2ConfUsLp0RtxSetting
Retransmission setting
Enumerationr/w
Enumerated Values:
0rtxOff
255rtxCustom
 .1.3.6.1.4.1.664.5.65.1.1.1.1.78
adGenVdsl2ConfUsLp0CustomRtxMaxNdr
Retransmission maximum allowed net data rate.
Valid values are in 8000 bps increments.
bpsUnsigned32r/w
Constraints:
range: 0-96000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.79
adGenVdsl2ConfUsLp0CustomRtxMinDelay
Retransmission minimum allowed delay
msInteger32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.80
adGenVdsl2ConfUsLp0CustomRtxMaxDelay
Retransmission maximum allowed delay
msInteger32r/w
Constraints:
range: 1-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.81
adGenVdsl2ConfUsLp0CustomRtxInpMinShine
Retransmission minimum impulse noise protection against
SHINE when subcarrier spacing is 4.3125Khz
DMT symbolsInteger32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.82
adGenVdsl2ConfUsLp0CustomRtxInpMinRein
Retransmission minimum impulse noise protection against
REIN when subcarrier spacing is 4.3125Khz
DMT symbolsInteger32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.664.5.65.1.1.1.1.83
adGenVdsl2ConfUsLp0CustomRtxIatRein
Retransmission inter-arrival time for REIN
Enumerationr/w
Enumerated Values:
1rtxRein100Hz
2rtxRein120Hz
 .1.3.6.1.4.1.664.5.65.1.1.1.1.84
adGenVdsl2ConfUsLp0CustomRtxLeftrThresh
Retransmission parameter that specifies the fraction of
the NDR used as the threshold to declare leftr defects.
A minimum value of ETR/2 is required. A special value
of 0 sets the threshold to ETR.
NDR - net data rat…
Percent of NDRInteger32r/w
Constraints:
range: 0-99
 .1.3.6.1.4.1.664.5.65.1.1.1.1.85
adGenVdsl2ConfDsLp0RtxSetting
Retransmission setting
Enumerationr/w
Enumerated Values:
0rtxOff
255rtxCustom
 .1.3.6.1.4.1.664.5.65.1.1.1.1.86
adGenVdsl2ConfDsLp0CustomRtxMaxNdr
Retransmission maximum allowed net data rate.
Valid values are in 8000 bps increments.
bpsUnsigned32r/w
Constraints:
range: 0-350000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.87
adGenVdsl2ConfDsLp0CustomRtxMinDelay
Retransmission minimum allowed delay
msInteger32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.88
adGenVdsl2ConfDsLp0CustomRtxMaxDelay
Retransmission maximum allowed delay
msInteger32r/w
Constraints:
range: 1-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.89
adGenVdsl2ConfDsLp0CustomRtxInpMinShine
Retransmission minimum impulse noise protection against
SHINE when subcarrier spacing is 4.3125Khz
DMT symbolsInteger32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.90
adGenVdsl2ConfDsLp0CustomRtxInpMinRein
Retransmission minimum impulse noise protection against
REIN when subcarrier spacing is 4.3125Khz
DMT symbolsInteger32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.664.5.65.1.1.1.1.91
adGenVdsl2ConfDsLp0CustomRtxIatRein
Retransmission inter-arrival time for REIN
Enumerationr/w
Enumerated Values:
1rtxRein100Hz
2rtxRein120Hz
 .1.3.6.1.4.1.664.5.65.1.1.1.1.92
adGenVdsl2ConfDsLp0CustomRtxLeftrThresh
Retransmission parameter that specifies the fraction of
the NDR used as the threshold to declare leftr defects.
A minimum value of ETR/2 is required. A special value
of 0 sets the threshold to ETR.
NDR - net data rat…
Percent of NDRInteger32r/w
Constraints:
range: 0-99
 .1.3.6.1.4.1.664.5.65.1.1.1.1.93
adGenVdsl2ConfUsLp1RtxSetting
Retransmission setting
Enumerationr/w
Enumerated Values:
0rtxOff
255rtxCustom
 .1.3.6.1.4.1.664.5.65.1.1.1.1.94
adGenVdsl2ConfUsLp1CustomRtxMaxNdr
Retransmission maximum allowed net data rate.
Valid values are in 8000 bps increments.
bpsUnsigned32r/w
Constraints:
range: 0-96000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.95
adGenVdsl2ConfUsLp1CustomRtxMinDelay
Retransmission minimum allowed delay
msInteger32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.96
adGenVdsl2ConfUsLp1CustomRtxMaxDelay
Retransmission maximum allowed delay
msInteger32r/w
Constraints:
range: 1-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.97
adGenVdsl2ConfUsLp1CustomRtxInpMinShine
Retransmission minimum impulse noise protection against
SHINE when subcarrier spacing is 4.3125Khz
DMT symbolsInteger32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.98
adGenVdsl2ConfUsLp1CustomRtxInpMinRein
Retransmission minimum impulse noise protection against
REIN when subcarrier spacing is 4.3125Khz
DMT symbolsInteger32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.664.5.65.1.1.1.1.99
adGenVdsl2ConfUsLp1CustomRtxIatRein
Retransmission inter-arrival time for REIN
Enumerationr/w
Enumerated Values:
1rtxRein100Hz
2rtxRein120Hz
 .1.3.6.1.4.1.664.5.65.1.1.1.1.100
adGenVdsl2ConfUsLp1CustomRtxLeftrThresh
Retransmission parameter that specifies the fraction of
the NDR used as the threshold to declare leftr defects.
A minimum value of ETR/2 is required. A special value
of 0 sets the threshold to ETR.
NDR - net data rat…
Percent of NDRInteger32r/w
Constraints:
range: 0-99
 .1.3.6.1.4.1.664.5.65.1.1.1.1.101
adGenVdsl2ConfDsLp1RtxSetting
Retransmission setting
Enumerationr/w
Enumerated Values:
0rtxOff
255rtxCustom
 .1.3.6.1.4.1.664.5.65.1.1.1.1.102
adGenVdsl2ConfDsLp1CustomRtxMaxNdr
Retransmission maximum allowed net data rate.
Valid values are in 8000 bps increments.
bpsUnsigned32r/w
Constraints:
range: 0-350000000
 .1.3.6.1.4.1.664.5.65.1.1.1.1.103
adGenVdsl2ConfDsLp1CustomRtxMinDelay
Retransmission minimum allowed delay
msInteger32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.104
adGenVdsl2ConfDsLp1CustomRtxMaxDelay
Retransmission maximum allowed delay
msInteger32r/w
Constraints:
range: 1-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.105
adGenVdsl2ConfDsLp1CustomRtxInpMinShine
Retransmission minimum impulse noise protection against
SHINE when subcarrier spacing is 4.3125Khz
DMT symbolsInteger32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.664.5.65.1.1.1.1.106
adGenVdsl2ConfDsLp1CustomRtxInpMinRein
Retransmission minimum impulse noise protection against
REIN when subcarrier spacing is 4.3125Khz
DMT symbolsInteger32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.664.5.65.1.1.1.1.107
adGenVdsl2ConfDsLp1CustomRtxIatRein
Retransmission inter-arrival time for REIN
Enumerationr/w
Enumerated Values:
1rtxRein100Hz
2rtxRein120Hz
 .1.3.6.1.4.1.664.5.65.1.1.1.1.108
adGenVdsl2ConfDsLp1CustomRtxLeftrThresh
Retransmission parameter that specifies the fraction of
the NDR used as the threshold to declare leftr defects.
A minimum value of ETR/2 is required. A special value
of 0 sets the threshold to ETR.
NDR - net data rat…
Percent of NDRInteger32r/w
Constraints:
range: 0-99
 .1.3.6.1.4.1.664.5.65.1.1.1.1.109
adGenVdsl2ConfAmRadioFreqMask1
AM radio station 1 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies around radio station 1 center frequency.
kHzInteger32r/w
Constraints:
range: 0-0
range: 540-1700
 .1.3.6.1.4.1.664.5.65.1.1.1.1.110
adGenVdsl2ConfAmRadioFreqMask2
AM radio station 2 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies around radio station 2 center frequency.
kHzInteger32r/w
Constraints:
range: 0-0
range: 540-1700
 .1.3.6.1.4.1.664.5.65.1.1.1.1.111
adGenVdsl2ConfAmRadioFreqMask3
AM radio station 3 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies around radio station 3 center frequency.
kHzInteger32r/w
Constraints:
range: 0-0
range: 540-1700
 .1.3.6.1.4.1.664.5.65.1.1.1.1.112
adGenVdsl2ConfAmRadioFreqMask4
AM radio station 4 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies around radio station 4 center frequency.
kHzInteger32r/w
Constraints:
range: 0-0
range: 540-1700
 .1.3.6.1.4.1.664.5.65.1.1.1.1.113
adGenVdsl2ConfAmRadioFreqMask5
AM radio station 5 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies around radio station 5 center frequency.
kHzInteger32r/w
Constraints:
range: 0-0
range: 540-1700
 .1.3.6.1.4.1.664.5.65.1.1.1.1.114
adGenVdsl2ConfAmRadioFreqMask6
AM radio station 6 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies around radio station 6 center frequency.
kHzInteger32r/w
Constraints:
range: 0-0
range: 540-1700
 .1.3.6.1.4.1.664.5.65.1.1.1.1.115
adGenVdsl2ConfMemorySplitRatio
This parameter defines the ratio of how the interleaver memory
is allocated between the downstream and upstream directions.
For example a ratio of 2:1 will assign twice as much interleaver
memory to the downstream path …
Enumerationr/w
Enumerated Values:
1oneToOne
2twoToOne
3threeToOne
4fourToOne
5fiveToOne
 .1.3.6.1.4.1.664.5.65.1.1.1.1.116

adGenVdsl2LineAlarmConfProfileTable

table
.1.3.6.1.4.1.664.5.65.1.1.2 · 1 row entry · 25 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2LineAlarmConfProfileTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2LineAlarmConfProfileTable' 
This table contains information on the VDSL2 line
configuration.  One entry in this table reflects a
profile defined by a manager which can be used to
configure the modem for a physical line
adGenVdsl2LineAlarmConfProfileEntry row .1.3.6.1.4.1.664.5.65.1.1.2.1
Each entry consists of a list of parameters that
represents the configuration of an VDSL2 modem.

`Static' profiles - profiles are automaticly
created or destroyed as VDSL2 physical lines
are discovered a…
Indexes
Column Syntax OID
adGenVdsl2LineAlarmConfProfileName
This object is used by the line configuration table
in order to identify a row of this table.

This value cannot be user-specified and is not dynamic.

There is a one-to-one relationship betw…
OctetString
Constraints:
range: 1-10
 .1.3.6.1.4.1.664.5.65.1.1.2.1.1
adGenVdsl2VtucThreshSnrMgn
The SNR margin on the VDSL2 interface below which
the SNMP agent sends an adGenVdsl2USPerfSNRThresTrap.
One trap will be sent per interval per interface.
A value of '0' will disable the trap.
dBInteger32r/w
Constraints:
range: 0-99
 .1.3.6.1.4.1.664.5.65.1.1.2.1.2
adGenVdsl2VtucThresh15MinLofs
The number of Loss of Frame Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VtucPerfLofsThreshTrap.
One trap wil…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.3
adGenVdsl2VtucThresh15MinLoss
The number of Loss of Signal Seconds
encountered by VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VtucPerfLossThreshTrap.
One trap will …
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.4
adGenVdsl2VtucThresh15MinLols
The number of Loss of Link Seconds
encountered by VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VtucPerfLolsThreshTrap.
One trap will be…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.5
adGenVdsl2VtucThresh15MinLprs
The number of Loss of Power Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VtucPerfLprsThreshTrap.
One trap wil…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.6
adGenVdsl2VtucThresh15MinEs
The number of Errored Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VtucPerfESThreshTrap.
One trap will be sen…
secondsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.7
adGenVdsl2VtucThresh15MinSes
The number of Errored Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VtucPerfSESThreshTrap.
One trap will be se…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.8
adGenVdsl2VtucThresh15MinUas
The number of Errored Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VtucPerfUASThreshTrap.
One trap will be se…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.9
adGenVdsl2VturThreshSnrMgn
The SNR Margin on the VDSL2 interface below which
the SNMP agent sends an adGenVdsl2DSPerfSNRThresTrap.
One trap will be sent per interval per interface.
A value of '0' will disable the trap.
dBInteger32r/w
Constraints:
range: 0-99
 .1.3.6.1.4.1.664.5.65.1.1.2.1.10
adGenVdsl2VturThresh15MinLofs
The number of Loss of Frame Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VturPerfLofsThreshTrap.
One trap wil…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.11
adGenVdsl2VturThresh15MinLoss
The number of Loss of Signal Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VturPerfLossThreshTrap.
One trap wi…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.12
adGenVdsl2VturThresh15MinLprs
The number of Loss of Power Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VturPerfLprsThreshTrap.
One trap wil…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.13
adGenVdsl2VturThresh15MinEs
The number of Errored Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VturPerfESThreshTrap.
One trap will be sen…
secondsUnsigned32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.664.5.65.1.1.2.1.14
adGenVdsl2VturThresh15MinSes
The number of Errored Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VturPerfSESThreshTrap.
One trap will be se…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.15
adGenVdsl2VturThresh15MinUas
The number of Errored Seconds
encountered by an VDSL2 interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adGenVdsl2VturPerfUASThreshTrap.
One trap will be se…
secondsUnsigned32r/w
Constraints:
range: 0-900
 .1.3.6.1.4.1.664.5.65.1.1.2.1.16
adGenVdsl2LineAlarmConfProfileRowStatus
This object is used to create a new row or modify or
delete an existing row in this table.

A profile activated by setting this object to
`active'. When `active' is set, the system
will validate the profi…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.664.5.65.1.1.2.1.17
adGenVdsl2ThreshUsLp0RateUp
Configured change in rate on the latency path causing an
adGenVdsl2VtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.
bpsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.18
adGenVdsl2ThreshUsLp0RateDown
Configured change in rate on the latency path causing an
adGenVdsl2VtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.
bpsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.19
adGenVdsl2ThreshDsLp0RateUp
Configured change in rate on the latency path causing an
adGenVdsl2VtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.
bpsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.20
adGenVdsl2ThreshDsLp0RateDown
Configured change in rate on the latency path causing an
adGenVdsl2VtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.
bpsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.21
adGenVdsl2ThreshUsLp1RateUp
Configured change in rate on the latency path causing an
adGenVdsl2VtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.
bpsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.22
adGenVdsl2ThreshUsLp1RateDown
Configured change in rate on the latency path causing an
adGenVdsl2VtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.
bpsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.23
adGenVdsl2ThreshDsLp1RateUp
Configured change in rate on the latency path causing an
adGenVdsl2VtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.
bpsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.24
adGenVdsl2ThreshDsLp1RateDown
Configured change in rate on the latency path causing an
adGenVdsl2VtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.
bpsSNMPv2-SMIGauge32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.1.2.1.25

adGenVdsl2RestoreDefaultTable

table
.1.3.6.1.4.1.664.5.65.1.1.3 · 1 row entry · 1 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2RestoreDefaultTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2RestoreDefaultTable' 
This table contains items to restore line and/or
alarm provisioning to their default values.
adGenVdsl2RestoreDefaultEntry row .1.3.6.1.4.1.664.5.65.1.1.3.1
For later
Indexes
Column Syntax OID
adGenVdsl2ConfRestoreDefaults
This object is used to restore the set of provisioning
indicated. A read will always return a value of 1.
Enumerationr/w
Enumerated Values:
1restoreProvisioning
2restoreAlarms
3restoreAll
 .1.3.6.1.4.1.664.5.65.1.1.3.1.1

adGenVdsl2BandConfProfileTable

table
.1.3.6.1.4.1.664.5.65.1.1.4 · 1 row entry · 3 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2BandConfProfileTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2BandConfProfileTable' 
This table contains information on the VDSL2 Band
configuration.  One entry in this table reflects band
profile defined by a manager which can be used to
configure the VDSL2 bands for a given
adGenVdsl2LineConfProfileEntry.
adGenVdsl2BandConfProfileEntry row .1.3.6.1.4.1.664.5.65.1.1.4.1
Each entry consists of a list of parameters that
represents the configuration of an VDSL2 modem
band parameters. These entries extend that of the
adGenVdsl2LineConfProfileTable by band.
Indexes
Column Syntax OID
adGenVdsl2BandNumber
VDSL2 band number. Band values are 1 - 5 corresponding
to upstream bands U0..U4 and downstream bands D1..D5.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.1.4.1.1
adGenVdsl2BandConfUsCustomPboCableA
Upstream power back-off band cable A parameter.
This parameter defines the UPBO reference PSD used
to compute the upstream power backoff for each
upstream band except US0. A UPBOPSD defined for each
band shall consist o…
0.01 dBm/HzUnsigned32r/w
Constraints:
range: 4000-8095
 .1.3.6.1.4.1.664.5.65.1.1.4.1.2
adGenVdsl2BandConfUsCustomPboCableB
Upstream power back-off band cable B parameter.
This parameter defines the UPBO reference PSD used
to compute the upstream power backoff for each
upstream band except US0. A UPBOPSD defined for each
band shall consist o…
0.01 dBm/HzUnsigned32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.664.5.65.1.1.4.1.3

adGenVdsl2AlarmSlotProvTable

table
.1.3.6.1.4.1.664.5.65.1.1.5 · 1 row entry · 1 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2AlarmSlotProvTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2AlarmSlotProvTable' 
This table sets alarm severity for all VDSL2 interfaces.
adGenVdsl2AlarmSlotProvEntry row .1.3.6.1.4.1.664.5.65.1.1.5.1
Indexes
Column Syntax OID
adGenVdsl2AlmSlotLinkdownSeverity
Sets the Linkdown alarm severity (affects all VDSL2 Ports)
Enumerationr/w
Enumerated Values:
2info
3alert
4minor
5major
6critical
 .1.3.6.1.4.1.664.5.65.1.1.5.1.1

adGenVdsl2LineTable

table
.1.3.6.1.4.1.664.5.65.1.2.1 · 1 row entry · 8 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2LineTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2LineTable' 
This table includes common attributes describing
both ends of the line.  It is required for all VDSL2
physical interfaces.  VDSL2 physical interfaces are
those ifEntries where ifType is equal to vdsl(97).
adGenVdsl2LineEntry row .1.3.6.1.4.1.664.5.65.1.2.1.1
An entry in adGenVdsl2LineTable.
Indexes
Column Syntax OID
adGenVdsl2LineCoding
Specifies the VDSL2 coding type used on this
line.
Enumeration
Enumerated Values:
1other
2dmt
3cap
4qam
 .1.3.6.1.4.1.664.5.65.1.2.1.1.1
adGenVdsl2LinePortServiceState
VDSL2 port service state.
Enumerationr/w
Enumerated Values:
1is
2oosUas
3oosMA
 .1.3.6.1.4.1.664.5.65.1.2.1.1.3
adGenVdsl2LineStatus
Indicates current state of the dsl line.
Enumeration
Enumerated Values:
1portDown
2portTraining
3showtime
 .1.3.6.1.4.1.664.5.65.1.2.1.1.6
adGenVdsl2LineUpTime
Indicates the amount of time the line has
been in showtime.
secondsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.1.1.7
adGenVdsl2LineCurrTransSysMode
A report of the current operating xDSL line transmission mode.
offline (0) -- Unknow mode (not connected)
multiMode (1) -- Automatic mode selection
t1413 (2), -- T1.413 Mode
g9921a (3), …
Enumeration
Enumerated Values:
0unknown
1multimode
2t1413
3g9921a
4g9921b
5g9921c
6g9921h
7g9921i
8g9922
9g9922c
10g9923a
11g9923b
12g9923i
13g9923j
14g9923m
15g9923l
16g9924a
17g9924i
18g9925a
19g9925b
20g9925i
21g9925j
22g9925m
23g9931
24g9932a
25g9932b
26g9932c
27g9935
28g9932y
 .1.3.6.1.4.1.664.5.65.1.2.1.1.8
adGenVdsl2LineCurrBandProfile
The current VDSL2 band profile in use.
Enumeration
Enumerated Values:
0unknown
1g99328a
2g99328b
3g99328c
4g99328d
5g993212a
6g993212b
7g993217a
8g993230a
9g993217b
10g993235b
 .1.3.6.1.4.1.664.5.65.1.2.1.1.9
adGenVdsl2LineCurrEstimatedLength
 SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.1.1.10
adGenVdsl2LineCurrTpsTcFramingMode
Parameter that indicates the application-specific
Transport Protocol Specific Transmission
Convergence (TPS-TC) type.
Enumeration
Enumerated Values:
0auto
1atm
2efm
3hdlc
 .1.3.6.1.4.1.664.5.65.1.2.1.1.11

adGenVdsl2VtucPhysTable

table
.1.3.6.1.4.1.664.5.65.1.2.2 · 1 row entry · 21 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VtucPhysTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VtucPhysTable' 
This table provides one row for each Vtuc.
Each row contains the Physical Layer Parameters
table for that Vtuc. VDSL2 physical interfaces are
those ifEntries where ifType is equal to vdsl(97).
adGenVdsl2VtucPhysEntry row .1.3.6.1.4.1.664.5.65.1.2.2.1
An entry in the adGenVdsl2VtucPhysTable.
Indexes
Column Syntax OID
adGenVdsl2VtucInvSerialNumber
The vendor specific string that identifies the
vendor equipment.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.2.2.1.1
adGenVdsl2VtucInvVendorID
The vendor ID code is a copy of the binary
vendor identification field defined by the
PHY[10] and expressed as readable characters.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.2.2.1.2
adGenVdsl2VtucInvVersionNumber
The vendor specific version number sent by this ATU
as part of the initialization messages. It is a copy
of the binary version number field defined by the
PHY[10] and expressed as readable characters.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.2.2.1.3
adGenVdsl2CurrUSSnrMgn
Noise Margin as seen by this ATU with respect to its
received signal in tenth dB.
tenth dBInteger32
Constraints:
range: -640-640
 .1.3.6.1.4.1.664.5.65.1.2.2.1.4
adGenVdsl2CurrUSAtn
Measured difference in the total power transmitted by
the peer ATU and the total power received by this ATU.
tenth dBInteger32
Constraints:
range: 0-630
 .1.3.6.1.4.1.664.5.65.1.2.2.1.5
adGenVdsl2VtucCurrStatus
Indicates current state of the Vtuc line. This is a
bit-map of possible conditions. The various bit
positions are:

Bit 00 : There no defects on the line

Bit 01 : …
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.6
adGenVdsl2VtucCurrOutputPwr
Measured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence.
tenth dBmInteger32
Constraints:
range: -310-310
 .1.3.6.1.4.1.664.5.65.1.2.2.1.7
adGenVdsl2VtucCurrAttainableRate
Indicates the maximum currently attainable data rate
by the ATU. This value will be equal or greater than
the current line rate.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.8
adGenVdsl2VtucCurrTxRate
The payload rate of the last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.9
adGenVdsl2VtucPrevTxRate
The payload rate of the previous successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.10
adGenVdsl2VtucActTxPsd
Actual Power Spectrum Density (PSD) transmitted. The average
transmit PSD over the sub-carriers.
It ranges from -900 to 0 units of 0.1 dB
(Physical values are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indica…
0.1 dBInteger32
Constraints:
range: -900-0
range: 2147483647-2147483647
 .1.3.6.1.4.1.664.5.65.1.2.2.1.11
adGenVdsl2VtucCurrTpsTcStatus
Attributes with this syntax are status parameters that
reflect the failure status for Transmission Convergence (TC)
layer of a given data layer interface (data path over a VDSL2
/ADSL/ADSL2 or ADSL2+ link).
Enumeration
Enumerated Values:
0noDefect
1outOfSync
 .1.3.6.1.4.1.664.5.65.1.2.2.1.12
adGenVdsl2VtucCurrTxLineRate
The line rate, including all payload and
overhead rates.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.13
adGenVdsl2VtucPrevTxLineRate
The line rate, including all payload and
overhead rates, of the previous successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.14
adGenVdsl2VtucCircuitProviderCode
Returns local circuit provider code
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.2.2.1.15
adGenVdsl2VtucCurrTxRateMax
Returns max payload rate since last successful
train.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.16
adGenVdsl2VtucCurrTxRateMin
Returns min payload rate since last successful
train.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.17
adGenVdsl2VtucLastSraDownshift
Returns system uptime of last SRA downshift
since last successful train.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.664.5.65.1.2.2.1.18
adGenVdsl2VtucLastSraUpshift
Returns system uptime of last SRA upshift
since last successful train.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.664.5.65.1.2.2.1.19
adGenVdsl2VtucRtxUsed
Specifies whether retransmission is active in the
transmit direction.
Enumeration
Enumerated Values:
1rtxInUse
2rtxNotInUseForbidden
3rtxNotInUseNotSupportedXTUC
4rtxNotInUseNotSupportedXTUR
5rtxNotInUseNotSupportedXTUCAndXTUR
 .1.3.6.1.4.1.664.5.65.1.2.2.1.20
adGenVdsl2VtucRtxEtr
Expected throughput rate calculated from combined effect of
impulse noise protection against worst-case REIN and worst-case
SHINE and overhead from correction of stationary noise errors.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.2.1.21

adGenVdsl2VturPhysTable

table
.1.3.6.1.4.1.664.5.65.1.2.3 · 1 row entry · 21 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VturPhysTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VturPhysTable' 
This table provides one row for each Vtur.
Each row contains the Physical Layer Parameters
table for that Vtur. VDSL2 physical interfaces are
those ifEntries where ifType is equal to vdsl(97).
adGenVdsl2VturPhysEntry row .1.3.6.1.4.1.664.5.65.1.2.3.1
An entry in the adGenVdsl2VturPhysTable.
Indexes
Column Syntax OID
adGenVdsl2VturInvSerialNumber
The vendor specific string that identifies the
vendor equipment.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.2.3.1.1
adGenVdsl2VturInvVendorID
The vendor ID code is a copy of the binary
vendor identification field defined by the
PHY[10] and expressed as readable characters.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.2.3.1.2
adGenVdsl2VturInvVersionNumber
The vendor specific version number sent by this ATU
as part of the initialization messages. It is a copy
of the binary version number field defined by the
PHY[10] and expressed as readable characters.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.2.3.1.3
adGenVdsl2CurrDSSnrMgn
Noise Margin as seen by this ATU with respect to its
received signal in tenth dB.
tenth dBInteger32
Constraints:
range: -640-640
 .1.3.6.1.4.1.664.5.65.1.2.3.1.4
adGenVdsl2CurrDSAtn
Measured difference in the total power transmitted by
the peer ATU and the total power received by this ATU.
tenth dBInteger32
Constraints:
range: 0-630
 .1.3.6.1.4.1.664.5.65.1.2.3.1.5
adGenVdsl2VturCurrStatus
Indicates current state of the Vtur line. This is a
bit-map of possible conditions. Due to the isolation
of the Vtur when line problems occur, many state
conditions like loss of power, loss of quality signal,
and init…
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.6
adGenVdsl2VturCurrOutputPwr
Measured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence.
tenth dBmInteger32
Constraints:
range: -310-310
 .1.3.6.1.4.1.664.5.65.1.2.3.1.7
adGenVdsl2VturCurrAttainableRate
Indicates the maximum currently attainable data rate
by the ATU. This value will be equal or greater than
the current line rate.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.8
adGenVdsl2VturCurrTxRate
The payload rate of the last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.9
adGenVdsl2VturPrevTxRate
The payload rate of the previous successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.10
adGenVdsl2VturActTxPsd
Actual Power Spectrum Density (PSD) transmitted. The average
transmit PSD over the sub-carriers.
It ranges from -900 to 0 units of 0.1 dB
(Physical values are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indica…
0.1 dBInteger32
Constraints:
range: -900-0
range: 2147483647-2147483647
 .1.3.6.1.4.1.664.5.65.1.2.3.1.11
adGenVdsl2VturCurrTxLineRate
The line rate, including all payload and
overhead rates.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.12
adGenVdsl2VturPrevTxLineRate
The line rate, including all payload and
overhead rates, of the previous successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.13
adGenVdsl2VturCircuitProviderCode
Returns remote circuit provider code
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.2.3.1.14
adGenVdsl2VturCircuitCapabilities
Returns remote circuit capabilities in bit masks with following order:
0 - Disabled, 1 - Enabled
Byte Order of octet string:
Byte 0. Byte 1. Byte 2. Byte 3. Byte 4. Byte 5. Byte 6. Byte 7

Byte 0: Bit 2 - …
OctetString
Constraints:
range: 8-8
 .1.3.6.1.4.1.664.5.65.1.2.3.1.15
adGenVdsl2VturCurrTxRateMax
Returns max payload rate since last successful
train.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.16
adGenVdsl2VturCurrTxRateMin
Returns min payload rate since last successful
train.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.17
adGenVdsl2VturLastSraDownshift
Returns system uptime of last SRA downshift
since last successful train.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.664.5.65.1.2.3.1.18
adGenVdsl2VturLastSraUpshift
Returns system uptime of last SRA upshift
since last successful train.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.664.5.65.1.2.3.1.19
adGenVdsl2VturRtxUsed
Specifies whether retransmission is active in the
transmit direction.
Enumeration
Enumerated Values:
1rtxInUse
2rtxNotInUseForbidden
3rtxNotInUseNotSupportedXTUC
4rtxNotInUseNotSupportedXTUR
5rtxNotInUseNotSupportedXTUCAndXTUR
 .1.3.6.1.4.1.664.5.65.1.2.3.1.20
adGenVdsl2VturRtxEtr
Expected throughput rate calculated from combined effect of
impulse noise protection against worst-case REIN and worst-case
SHINE and overhead from correction of stationary noise errors.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.3.1.21

adGenVdsl2VtucChanTable

table
.1.3.6.1.4.1.664.5.65.1.2.4 · 1 row entry · 7 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VtucChanTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VtucChanTable' 
This table provides one row for each Vtuc channel.
VDSL2 channel interfaces are those ifEntries
where ifType is equal to channel.
adGenVdsl2VtucChanEntry row .1.3.6.1.4.1.664.5.65.1.2.4.1
An entry in the adGenVdsl2VtucChanTable.
Indexes
Column Syntax OID
adGenVdsl2VtucChannelNumber
VDSL2 logical channel. Channel values are 1 - 4.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.2.4.1.1
adGenVdsl2VtucChanInterleaveDelay
Interleave Delay for this channel.

Interleave delay applies only to the
interleave channel and defines the mapping
(relative spacing) between subsequent input
bytes at the interleaver input and their plac…
0.1 milli-secondsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.4.1.2
adGenVdsl2VtucChanCurrTxRate
Actual transmit rate on this channel.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.4.1.3
adGenVdsl2VtucChanPrevTxRate
The rate at the time of the last
adGenVdsl2VtucRateChangeTrap event. It is also set at
initialization to prevent a trap being sent.
Rate changes less than adGenVdsl2VtucThresh(*)RateDown
or less than adGenVdsl2VtucThres…
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.4.1.4
adGenVdsl2VtucChanCrcBlockLength
Indicates the length of the channel data-block
on which the CRC operates. Refer to Line Code
Specific MIBs, [11] and [12] for more
information.
byteSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.4.1.5
adGenVdsl2VtucChanINP
Current impulse noise protection on this channel,
measured in increments of 0.1 DMT symbols.
0.1 dmt symbolsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.4.1.6
adGenVdsl2VtucChanINPRein
Current impulse noise protection against REIN on this
channel, measured in increments of 0.1 DMT symbols.
0.1 dmt symbolsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.4.1.7

adGenVdsl2VturChanTable

table
.1.3.6.1.4.1.664.5.65.1.2.5 · 1 row entry · 7 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VturChanTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VturChanTable' 
This table provides one row for each Vtur channel.
VDSL2 channel interfaces are those ifEntries
where ifType is equal to channel.
adGenVdsl2VturChanEntry row .1.3.6.1.4.1.664.5.65.1.2.5.1
An entry in the adGenVdsl2VturChanTable.
Indexes
Column Syntax OID
adGenVdsl2VturChannelNumber
VDSL2 logical channel. Channel values are 1 - 4.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.2.5.1.1
adGenVdsl2VturChanInterleaveDelay
Interleave Delay for this channel.

Interleave delay applies only to the
interleave channel and defines the mapping
(relative spacing) between subsequent input
bytes at the interleaver input and their plac…
0.1 milli-secondsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.5.1.2
adGenVdsl2VturChanCurrTxRate
Actual transmit rate on this channel.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.5.1.3
adGenVdsl2VturChanPrevTxRate
The rate at the time of the last
adGenVdsl2VturRateChangeTrap event. It is also set at
initialization to prevent a trap being sent.
Rate changes less than adGenVdsl2VturThresh(*)RateDown
or less than adGenVdsl2VturThres…
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.5.1.4
adGenVdsl2VturChanCrcBlockLength
Indicates the length of the channel data-block
on which the CRC operates. Refer to Line Code
Specific MIBs, [11] and [12] for more
information.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.5.1.5
adGenVdsl2VturChanINP
Current impulse noise protection on this channel,
measured in increments of 0.1 DMT symbols.
0.1 dmt symbolsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.5.1.6
adGenVdsl2VturChanINPRein
Current impulse noise protection against REIN on this
channel, measured in increments of 0.1 DMT symbols.
0.1 dmt symbolsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.5.1.7

adGenVdsl2BandStatusTable

table
.1.3.6.1.4.1.664.5.65.1.2.6 · 1 row entry · 11 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2BandStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2BandStatusTable' 
This table contains per band status information for VDSL2
configuration.  One entry in this table reflects band
profile defined by a manager which can be used to
configure the VDSL2 bands for a given
adGenVdsl2LineConfProfileEntry.
adGenVdsl2BandStatusEntry row .1.3.6.1.4.1.664.5.65.1.2.6.1
Each entry consists of a list of band status items.
Indexes
Column Syntax OID
adGenVdsl2BandStatusNumber
VDSL2 band number. Band values are 1 - 5 corresponding
to upstream bands U0..U4 and downstream bands D1..D5.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.2.6.1.1
adGenVdsl2BandStatusUsStartCarrier
The starting carrier of the VDSL2 upstream band at 4.3125KHz
spacing
Unsigned32
Constraints:
range: 0-8192
 .1.3.6.1.4.1.664.5.65.1.2.6.1.2
adGenVdsl2BandStatusUsStopCarrier
The ending carrier of the VDSL2 upstream band at 4.3125KHz
spacing
Unsigned32
Constraints:
range: 0-8192
 .1.3.6.1.4.1.664.5.65.1.2.6.1.3
adGenVdsl2BandStatusUsMargin
Upstream Signal-to-Noise Ratio Margin per Band. This parameter
is defined by usable band. The upstream signal to noise ratio
margin per band is the maximum increase in dB of the noise
power received at the VTU-C such th…
0.1 dBInteger32
Constraints:
range: -641-630
 .1.3.6.1.4.1.664.5.65.1.2.6.1.4
adGenVdsl2BandStatusUsLatn
Upstream Line Attenuation per Band. This parameter is defined per
usable bands. It is the measured difference in the total power
transmitted in this band and the total power received over all
subcarriers of this band du…
0.1 dBInteger32
Constraints:
range: 0-1270
 .1.3.6.1.4.1.664.5.65.1.2.6.1.5
adGenVdsl2BandStatusUsSatn
Upstream Signal Attenuation per Band. This parameter is defined per
usable bands. It is the measured difference in the total power
transmitted in this band and the total power received over all
subcarriers of this band …
0.1 dBInteger32
Constraints:
range: 0-1270
 .1.3.6.1.4.1.664.5.65.1.2.6.1.6
adGenVdsl2BandStatusDsStartCarrier
The starting carrier of the VDSL2 downstream band at 4.3125KHz
spacing
Unsigned32
Constraints:
range: 0-8192
 .1.3.6.1.4.1.664.5.65.1.2.6.1.7
adGenVdsl2BandStatusDsStopCarrier
The ending carrier of the VDSL2 downstream band at 4.3125KHz
spacing
Unsigned32
Constraints:
range: 0-8192
 .1.3.6.1.4.1.664.5.65.1.2.6.1.8
adGenVdsl2BandStatusDsMargin
Downstream Signal-to-Noise Ratio Margin per Band. This parameter
is defined by usable band. The downstream signal to noise ratio
margin per band is the maximum increase in dB of the noise
power received at the VTU-R suc…
0.1 dBInteger32
Constraints:
range: -641-630
 .1.3.6.1.4.1.664.5.65.1.2.6.1.9
adGenVdsl2BandStatusDsLatn
Downstream Line Attenuation per Band. This parameter is defined per
usable bands. It is the measured difference in the total power
transmitted in this band and the total power received over all
subcarriers of this band …
0.1 dBInteger32
Constraints:
range: 0-1270
 .1.3.6.1.4.1.664.5.65.1.2.6.1.10
adGenVdsl2BandStatusDsSatn
Downstream Signal Attenuation per Band. This parameter is defined per
usable bands. It is the measured difference in the total power
transmitted in this band and the total power received over all
subcarriers of this ban…
0.1 dBInteger32
Constraints:
range: 0-1270
 .1.3.6.1.4.1.664.5.65.1.2.6.1.11

adGenVdsl2ScStatusTable

table
.1.3.6.1.4.1.664.5.65.1.2.7 · 1 row entry · 11 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2ScStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2ScStatusTable' 
This table contains per band status information for VDSL2
configuration.  One entry in this table reflects band
profile defined by a manager which can be used to
configure the VDSL2 bands for a given
adGenVdsl2LineConfProfileEntry.
adGenVdsl2ScStatusEntry row .1.3.6.1.4.1.664.5.65.1.2.7.1
Each entry consists of a list of band status items.
Indexes
Column Syntax OID
adGenVdsl2ScStatusNumber
DMT subcarrier number. There are 4096 possible DMT sub-carriers
spaced by 4.3125 KHz in the upstream and downstream directions.
These carriers are typically broken up into non-overlapping
groups called bands. For this r…
Integer32
Constraints:
range: 1-8192
 .1.3.6.1.4.1.664.5.65.1.2.7.1.1
adGenVdsl2ScStatusUsBits
Bits allocated per subcarrier in the upstream direction.
Value ranges from 0 to 15. A zero value indicates
that no bits are allocated the upstream subcarrier.
Integer32
Constraints:
range: 0-15
 .1.3.6.1.4.1.664.5.65.1.2.7.1.2
adGenVdsl2ScStatusUsGain
Upstream gains allocation per subcarrier. It is an array of integer
values in the range of 0 to 4095 for each subcarrier.
The gain value is represented as a multiple of 1/512 on
linear scale. The value of zero indicate…
Integer32
Constraints:
range: 0-4095
 .1.3.6.1.4.1.664.5.65.1.2.7.1.3
adGenVdsl2ScStatusUsSnr
Upstream signal to noise (SNR) per sub-carrier number. The SNR
ranges from 0 to +95.0 dB with 0.1 dB steps. A special value of
955 indicates that no measurement could be done for the
subcarrier because it is out of the …
0.1 dBInteger32
Constraints:
range: 0-955
 .1.3.6.1.4.1.664.5.65.1.2.7.1.4
adGenVdsl2ScStatusDsBits
Bits allocated per subcarrier in the downstream direction.
Value ranges from 0 to 15. A zero value indicates
that no bits are allocated the downstream subcarrier.
Integer32
Constraints:
range: 0-15
 .1.3.6.1.4.1.664.5.65.1.2.7.1.5
adGenVdsl2ScStatusDsGain
Downstream gains allocation per subcarrier. It is an array of
integer values in the range of 0 to 4095 for each subcarrier.
The gain value is represented as a multiple of 1/512 on
linear scale. The value of zero indica…
Integer32
Constraints:
range: 0-4095
 .1.3.6.1.4.1.664.5.65.1.2.7.1.6
adGenVdsl2ScStatusDsSnr
Downstream signal to noise (SNR) per sub-carrier number. The SNR
ranges from 0 to +95.0 dB with 0.1 dB steps. A special value of
955 indicates that no measurement could be done for the
subcarrier because it is out of th…
0.1 dBInteger32
Constraints:
range: 0-955
 .1.3.6.1.4.1.664.5.65.1.2.7.1.7
adGenVdsl2ScStatusUsQln
Upstream quiet line noise (QLN) per sub-carrier number. The QLN
ranges from -150.5 to -23.0 dBm/Hz with 0.1 dB steps. A special
value of -1505 indicates that no measurement could be done for the
subcarrier because it is…
0.1 dBm/HzInteger32
Constraints:
range: -1505--230
 .1.3.6.1.4.1.664.5.65.1.2.7.1.8
adGenVdsl2ScStatusDsQln
Upstream quiet line noise (QLN) per sub-carrier number. The QLN
ranges from -150.5 to -23.0 dBm/Hz with 0.1 dB steps. A special
value of -1505 indicates that no measurement could be done for the
subcarrier because it is…
0.1 dBm/HzInteger32
Constraints:
range: -1505--230
 .1.3.6.1.4.1.664.5.65.1.2.7.1.9
adGenVdsl2ScStatusUsHlog
Upstream channel transfer function (HLOG) per sub-carrier number. The HLOG
ranges from -96.3 to +6.0 dB with 0.1 dB steps. A special value of
-963 indicates that no measurement could be done for the
subcarrier because i…
0.1 dBInteger32
Constraints:
range: -963-60
 .1.3.6.1.4.1.664.5.65.1.2.7.1.10
adGenVdsl2ScStatusDsHlog
Downstream channel transfer function (HLOG) per sub-carrier number. The HLOG
ranges from -96.3 to +6.0 dB with 0.1 dB steps. A special value of
-963 indicates that no measurement could be done for the
subcarrier because…
0.1 dBInteger32
Constraints:
range: -963-60
 .1.3.6.1.4.1.664.5.65.1.2.7.1.11

adGenVdsl2ReserveInstanceBulkVDSLTlvTable

table
.1.3.6.1.4.1.664.5.65.1.2.8 · 1 row entry · 1 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2ReserveInstanceBulkVDSLTlvTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2ReserveInstanceBulkVDSLTlvTable' 
Table contains instances that are created when there is a request to reserve a Bulk VDSL instance
adGenVdsl2ReserveInstanceBulkVDSLTlvEntry row .1.3.6.1.4.1.664.5.65.1.2.8.1
Index is the slot number.
Indexes
Column Syntax OID
adGenVdsl2ReserveInstanceBulkVDSLSlotInstance
Used to index the Tlv table; each time this is called by slot it
creates an instance for that viewer
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.5.65.1.2.8.1.1

adGenVdsl2BulkVDSLTlvTable

table
.1.3.6.1.4.1.664.5.65.1.2.9 · 1 row entry · 4 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2BulkVDSLTlvTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2BulkVDSLTlvTable' 
Table contains filters that can be applied on the requested instances
adGenVdsl2BulkVDSLTlvEntry row .1.3.6.1.4.1.664.5.65.1.2.9.1
Indexes are the slot and instance number
Indexes
Column Syntax OID
adGenVdsl2BulkVDSLTlvInstance
Used to index the table by TLV Instance number.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.5.65.1.2.9.1.1
adGenVdsl2BulkVDSLTlvType
Used to set the type of VDSL info to return in the VDSL TLV instance:
1 - Bit Allocation Table (BAT), 2 - Signal Noise Ratio (SNR),
3 - Quiet Line Noise (QLN), 4 - Channel Transfer Function (HLOG)
Enumerationr/w
Enumerated Values:
1bat
2snr
3qln
4hlog
 .1.3.6.1.4.1.664.5.65.1.2.9.1.2
adGenVdsl2BulkVDSLTlvPort
Used to set the VDSL port to get the info for VDSL TLV instance
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.2.9.1.3
adGenVdsl2BulkVDLSTlvCreate
Set this OID to 1 to update the instance with Bulk VDSL info depending on type set.
A get on this OID always returns a 1.
Enumerationr/w
Enumerated Values:
1updateinstance
 .1.3.6.1.4.1.664.5.65.1.2.9.1.4

adGenVdsl2VtucPerfDataTable

table
.1.3.6.1.4.1.664.5.65.1.3.1 · 1 row entry · 62 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VtucPerfDataTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VtucPerfDataTable' 
This table provides one row for each Vtuc.
VDSL2 physical interfaces are
those ifEntries where ifType is equal to vdsl(97).
adGenVdsl2VtucPerfDataEntry row .1.3.6.1.4.1.664.5.65.1.3.1.1
An entry in adGenVdsl2VtucPerfDataTable.
Indexes
Column Syntax OID
adGenVdsl2VtucPerfLofs
Count of the number of Loss of Framing failures since
agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.1
adGenVdsl2VtucPerfLoss
Count of the number of Loss of Signal failures since
agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.2
adGenVdsl2VtucPerfLols
Count of the number of Loss of Link failures since
agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.3
adGenVdsl2VtucPerfLprs
Count of the number of Loss of Power failures since
agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.4
adGenVdsl2VtucPerfEs
Count of Errored Seconds since the unit was last reset.
An Errored Second is a one-second interval containing one
or more CRC anomalies, or one or more LOS or LOF defects.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.5
adGenVdsl2VtucPerfInits
Count of the line initialization attempts since
agent reset. Includes both successful and failed
attempts.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.6
adGenVdsl2VtucPerfSes
Count of Severely Errored Seconds since the unit was last
reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.7
adGenVdsl2VtucPerfUas
Count of Unavailable Seconds since the unit was last
reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.8
adGenVdsl2VtucPerfFecs
Count of the number of FEC Seconds since agent
reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.9
adGenVdsl2VtucPerfCrc
Count of the number of CRC anomolies since agent
reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.10
adGenVdsl2VtucPerfFec
Count of the number of FEC anomolies since agent
reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.11
adGenVdsl2VtucPerfValidIntervals
The number of previous 15-minute intervals in the
interval table for which data was collected. Given
that <n> is the maximum # of intervals supported.
The value will be <n> unless the measurement was
(re-)started withi…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.664.5.65.1.3.1.1.12
adGenVdsl2VtucPerfInvalidIntervals
The number of intervals in the range from
0 to the value of adGenVdsl2VtucPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are not a…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.664.5.65.1.3.1.1.13
adGenVdsl2VtucPerfCurr15MinTimeElapsed
Total elapsed seconds in this interval.
secondsUnsigned32
Constraints:
range: 0-899
 .1.3.6.1.4.1.664.5.65.1.3.1.1.14
adGenVdsl2VtucPerfCurr15MinLofs
Count of seconds in the current 15 minute interval
when there was Loss of Framing.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.15
adGenVdsl2VtucPerfCurr15MinLoss
Count of seconds in the current 15 minute interval
when there was Loss of Signal.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.16
adGenVdsl2VtucPerfCurr15MinLols
Count of seconds in the current 15 minute interval
when there was Loss of Link.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.17
adGenVdsl2VtucPerfCurr15MinLprs
Count of seconds in the current 15 minute interval
when there was Loss of Power.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.18
adGenVdsl2VtucPerfCurr15MinEs
Count of Errored Seconds during this interval. An Errored
Second is a one-second interval containing one or more CRC
anomalies, or one or more LOS or LOF defects.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.19
adGenVdsl2VtucPerfCurr15MinInits
Count of the line initialization attempts in the
current 15 minute interval. Includes both successful
and failed attempts.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.20
adGenVdsl2VtucPerfCurr15MinSes
Count of Severely Errored Seconds in the current 15
minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.21
adGenVdsl2VtucPerfCurr15MinUas
Count of Unavailable Seconds in the current 15
minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.22
adGenVdsl2VtucPerfCurr15MinFecs
Count of FEC Seconds in the current 15 minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.23
adGenVdsl2VtucPerfCurr15MinCrc
Count of CRC anomolies in the current 15 minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.24
adGenVdsl2VtucPerfCurr15MinFec
Count of FEC anomolies in the current 15 minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.25
adGenVdsl2VtucPerfCurr1DayTimeElapsed
Number of seconds that have elapsed since the
beginning of the current 1-day interval.
secondsUnsigned32
Constraints:
range: 0-86399
 .1.3.6.1.4.1.664.5.65.1.3.1.1.26
adGenVdsl2VtucPerfCurr1DayLofs
Count of the number of seconds when there was Loss
of Framing during the current day as measured by
adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.27
adGenVdsl2VtucPerfCurr1DayLoss
Count of the number of seconds when there was Loss
of Signal during the current day as measured by
adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.28
adGenVdsl2VtucPerfCurr1DayLols
Count of the number of seconds when there was Loss
of Link during the current day as measured by
adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.29
adGenVdsl2VtucPerfCurr1DayLprs
Count of the number of seconds when there was Loss
of Power during the current day as measured by
adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.30
adGenVdsl2VtucPerfCurr1DayEs
Count of Errored Seconds (ES) since the beginning
of the current 1-day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.31
adGenVdsl2VtucPerfCurr1DayInits
Count of the line initialization attempts in the
day as measured by adGenVdsl2VtucPerfCurr1DayTimeElapsed.
Includes both successful and failed attempts.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.32
adGenVdsl2VtucPerfCurr1DaySes
Count of Severely Errored Seconds during the current day as
measured by adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.33
adGenVdsl2VtucPerfCurr1DayUas
Count of Unavailable Seconds during the current day as
measured by adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.34
adGenVdsl2VtucPerfCurr1DayFecs
Count of FEC Seconds during the current day as
measured by adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.35
adGenVdsl2VtucPerfCurr1DayCrc
Count of CRC anomolies during the current day as
measured by adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.36
adGenVdsl2VtucPerfCurr1DayFec
Count of FEC anomolies during the current day as
measured by adGenVdsl2VtucPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.37
adGenVdsl2VtucPerfTcTxUnits
Count of total transmitted transmission convergence layer
(TC) cells (ATM framing mode) or packets (other framing
modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.38
adGenVdsl2VtucPerfTcTxDataUnits
Count of data carrying transmitted transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.39
adGenVdsl2VtucPerfTcTxDataOctets
Count of octets in data carrying transmitted transmission
convergence layer (TC) cells (ATM framing mode) or packets
(other framing modes).
octetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.40
adGenVdsl2VtucPerfTcTxIdleUnits
Count of idle/pause transmitted transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.41
adGenVdsl2VtucPerfTcRxUnits
Count of total transmitted transmission convergence layer
(TC) cells (ATM framing mode) or packets (other framing
modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.42
adGenVdsl2VtucPerfTcRxDataUnits
Count of data carrying received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.43
adGenVdsl2VtucPerfTcRxDataOctets
Count of octets in data carrying received transmission
convergence layer (TC) cells (ATM framing mode) or packets
(other framing modes).
octetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.44
adGenVdsl2VtucPerfTcRxIdleUnits
Count of idle/pause received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.45
adGenVdsl2VtucPerfTcRxErroredUnits
Count of errored received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.46
adGenVdsl2VtucPerfSraDownshifts
Free-rolling count of SRA payload rate downshifts
since last successful train.
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.47
adGenVdsl2VtucPerfSraUpshifts
Free-rolling count of SRA payload rate upshifts
since last successful train.
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.48
adGenVdsl2VtucPerfCurr15MinSraDownshifts
Count of SRA payload rate downshifts since last
successful train in the current 15-min interval
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.49
adGenVdsl2VtucPerfCurr15MinSraUpshifts
Count of SRA payload rate upshifts since last
successful train in the current 15-min interval
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.50
adGenVdsl2VtucPerfCurr15MinSraRateMax
Max payload rate in the current 15-min interval
since last successful train. Min and max rate
should only be different in the case of an SRA
event.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.51
adGenVdsl2VtucPerfCurr15MinSraRateMin
Min payload rate in the current 15-min interval
since last successful train. Min and max rate
should only be different in the case of an SRA
event.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.52
adGenVdsl2VtucPerfCurr1DaySraDownshifts
Count of SRA payload rate downshifts since last
successful train in the current 24-hr interval
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.53
adGenVdsl2VtucPerfCurr1DaySraUpshifts
Count of SRA payload rate upshifts since last
successful train in the current 24-hr interval
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.54
adGenVdsl2VtucPerfCurr1DaySraRateMax
Max payload rate in the current 24-hr interval
since last successful train. Min and max rate
should only be different in the case of an SRA
event.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.55
adGenVdsl2VtucPerfCurr1DaySraRateMin
Min payload rate in the current 24-hr interval
since last successful train. Min and max rate
should only be different in the case of an SRA
event.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.56
adGenVdsl2VtucPerfRtxMinEftr
Retransmission parameter defined as the minimum of
the error-free throughput rate observed since reset.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.57
adGenVdsl2VtucPerfRtxLeftrs
Count of low error-free throughput rate defect
seconds since reset.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.58
adGenVdsl2VtucPerfCurr15MinRtxMinEftr
Retransmission parameter defined as the minimum of
the error-free throughput rate observed in the
current 15-min interval.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.59
adGenVdsl2VtucPerfCurr15MinRtxLeftrs
Count of low error-free throughput rate defect
seconds in the current 15-min interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.60
adGenVdsl2VtucPerfCurr1DayRtxMinEftr
Retransmission parameter showing the minimum of
the error-free throughput rate observed in the
current 24-hr interval.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.61
adGenVdsl2VtucPerfCurr1DayRtxLeftrs
Count of low error-free throughput rate defect
seconds in the current 24-hr interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.1.1.62

adGenVdsl2VturPerfDataTable

table
.1.3.6.1.4.1.664.5.65.1.3.2 · 1 row entry · 56 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VturPerfDataTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VturPerfDataTable' 
This table provides one row for each Vtur.
VDSL2 physical interfaces are
those ifEntries where ifType is equal to vdsl(97).
adGenVdsl2VturPerfDataEntry row .1.3.6.1.4.1.664.5.65.1.3.2.1
An entry in adGenVdsl2VturPerfDataTable.
Indexes
Column Syntax OID
adGenVdsl2VturPerfLofs
Count of the number of Loss of Framing failures since
agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.1
adGenVdsl2VturPerfLoss
Count of the number of Loss of Signal failures since
agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.2
adGenVdsl2VturPerfLprs
Count of the number of Loss of Power failures since
agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.3
adGenVdsl2VturPerfEs
Count of Errored Seconds since the unit was last reset.
An Errored Second is a one-second interval containing one
or more CRC anomalies, or one or more LOS or LOF defects.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.4
adGenVdsl2VturPerfSes
Count of Severely Errored Seconds since the unit was last
reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.5
adGenVdsl2VturPerfUas
Count of Unavailable Seconds since the unit was last reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.6
adGenVdsl2VturPerfFecs
Count of the number of FEC Seconds since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.7
adGenVdsl2VturPerfCrc
Count of the number of CRC anomolies since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.8
adGenVdsl2VturPerfFec
Count of the number of FEC anomolies since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.9
adGenVdsl2VturPerfValidIntervals
The number of previous 15-minute intervals in the
interval table for which data was collected. Given
that <n> is the maximum # of intervals supported.
The value will be <n> unless the measurement was
(re-)started withi…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.664.5.65.1.3.2.1.10
adGenVdsl2VturPerfInvalidIntervals
The number of intervals in the range from
0 to the value of adGenVdsl2VturPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are not a…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.664.5.65.1.3.2.1.11
adGenVdsl2VturPerfCurr15MinTimeElapsed
Total elapsed seconds in this interval.
secondsUnsigned32
Constraints:
range: 0-899
 .1.3.6.1.4.1.664.5.65.1.3.2.1.12
adGenVdsl2VturPerfCurr15MinLofs
Count of seconds in the current 15 minute interval
when there was Loss of Framing.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.13
adGenVdsl2VturPerfCurr15MinLoss
Count of seconds in the current 15 minute interval
when there was Loss of Signal.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.14
adGenVdsl2VturPerfCurr15MinLprs
Count of seconds in the current 15 minute interval
when there was Loss of Power.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.15
adGenVdsl2VturPerfCurr15MinEs
Count of Errored Seconds in the current 15 minute interval.
An Errored Second is a one-second interval containing one or
more CRC anomalies, or one or more LOS or LOF defects.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.16
adGenVdsl2VturPerfCurr15MinSes
Count of Severely Errored Seconds in the current 15
minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.17
adGenVdsl2VturPerfCurr15MinUas
Count of Unavailable Seconds in the current 15
minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.18
adGenVdsl2VturPerfCurr15MinFecs
Count of FEC Seconds in the current 15 minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.19
adGenVdsl2VturPerfCurr15MinCrc
Count of CRC anomolies in the current 15 minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.20
adGenVdsl2VturPerfCurr15MinFec
Count of FEC anomolies in the current 15 minute interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.21
adGenVdsl2VturPerfCurr1DayTimeElapsed
Number of seconds that have elapsed since the
beginning of the current 1-day interval.
secondsUnsigned32
Constraints:
range: 0-86399
 .1.3.6.1.4.1.664.5.65.1.3.2.1.22
adGenVdsl2VturPerfCurr1DayLofs
Count of the number of seconds when there was Loss
of Framing during the current day as measured by
adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.23
adGenVdsl2VturPerfCurr1DayLoss
Count of the number of seconds when there was Loss
of Signal during the current day as measured by
adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.24
adGenVdsl2VturPerfCurr1DayLprs
Count of the number of seconds when there was Loss
of Power during the current day as measured by
adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.25
adGenVdsl2VturPerfCurr1DayEs
Count of the number of seconds when there was Errored Seconds
during the current day as measured by
adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.26
adGenVdsl2VturPerfCurr1DaySes
Count of Severely Errored Seconds during the current day as
measured by adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.27
adGenVdsl2VturPerfCurr1DayUas
Count of Unavailable Seconds during the current day as
measured by adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.28
adGenVdsl2VturPerfCurr1DayFecs
Count of FEC Seconds during the current day as
measured by adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.29
adGenVdsl2VturPerfCurr1DayCrc
Count of CRC anomolies during the current day as
measured by adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.30
adGenVdsl2VturPerfCurr1DayFec
Count of FEC anomolies during the current day as
measured by adGenVdsl2VturPerfCurr1DayTimeElapsed.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.31
adGenVdsl2VturPerfTcTxUnits
Count of total transmitted transmission convergence layer
(TC) cells (ATM framing mode) or packets (other framing
modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.32
adGenVdsl2VturPerfTcTxDataUnits
Count of data carrying transmitted transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.33
adGenVdsl2VturPerfTcTxDataOctets
Count of octets in data carrying transmitted transmission
convergence layer (TC) cells (ATM framing mode) or packets
(other framing modes).
octetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.34
adGenVdsl2VturPerfTcTxIdleUnits
Count of idle/pause transmitted transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.35
adGenVdsl2VturPerfTcRxUnits
Count of total transmitted transmission convergence layer
(TC) cells (ATM framing mode) or packets (other framing
modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.36
adGenVdsl2VturPerfTcRxDataUnits
Count of data carrying received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.37
adGenVdsl2VturPerfTcRxDataOctets
Count of octets in data carrying received transmission
convergence layer (TC) cells (ATM framing mode) or packets
(other framing modes).
octetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.38
adGenVdsl2VturPerfTcRxIdleUnits
Count of idle/pause received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.39
adGenVdsl2VturPerfTcRxErroredUnits
Count of errored received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.40
adGenVdsl2VturPerfSraDownshifts
Free-rolling count of SRA payload rate downshifts
since last successful train.
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.41
adGenVdsl2VturPerfSraUpshifts
Free-rolling count of SRA payload rate upshifts
since last successful train.
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.42
adGenVdsl2VturPerfCurr15MinSraDownshifts
Count of SRA payload rate downshifts since last
successful train in the current 15-min interval
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.43
adGenVdsl2VturPerfCurr15MinSraUpshifts
Count of SRA payload rate upshifts since last
successful train in the current 15-min interval
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.44
adGenVdsl2VturPerfCurr15MinSraRateMax
Max payload rate in the current 15-min interval
since last successful train. Min and max rate
should only be different in the case of an SRA
event.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.45
adGenVdsl2VturPerfCurr15MinSraRateMin
Min payload rate in the current 15-min interval
since last successful train. Min and max rate
should only be different in the case of an SRA
event.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.46
adGenVdsl2VturPerfCurr1DaySraDownshifts
Count of SRA payload rate downshifts since last
successful train in the current 24-hr interval
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.47
adGenVdsl2VturPerfCurr1DaySraUpshifts
Count of SRA payload rate upshifts since last
successful train in the current 24-hr interval
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.48
adGenVdsl2VturPerfCurr1DaySraRateMax
Max payload rate in the current 24-hr interval
since last successful train. Min and max rate
should only be different in the case of an SRA
event.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.49
adGenVdsl2VturPerfCurr1DaySraRateMin
Min payload rate in the current 24-hr interval
since last successful train. Min and max rate
should only be different in the case of an SRA
event.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.50
adGenVdsl2VturPerfRtxMinEftr
Retransmission parameter defined as the minimum of
the error-free throughput rate observed since reset.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.51
adGenVdsl2VturPerfRtxLeftrs
Count of low error-free throughput rate defect
seconds since reset.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.52
adGenVdsl2VturPerfCurr15MinRtxMinEftr
Retransmission parameter defined as the minimum of
the error-free throughput rate observed in the
current 15-min interval.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.53
adGenVdsl2VturPerfCurr15MinRtxLeftrs
Count of low error-free throughput rate defect
seconds in the current 15-min interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.54
adGenVdsl2VturPerfCurr1DayRtxMinEftr
Retransmission parameter showing the minimum of
the error-free throughput rate observed in the
current 24-hr interval.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.55
adGenVdsl2VturPerfCurr1DayRtxLeftrs
Count of low error-free throughput rate defect
seconds in the current 24-hr interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.2.1.56

adGenVdsl2VtucIntervalTable

table
.1.3.6.1.4.1.664.5.65.1.3.3 · 1 row entry · 19 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VtucIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VtucIntervalTable' 
This table provides one row for each Vtuc
performance data collection interval.
VDSL2 physical interfaces are
those ifEntries where ifType is equal to vdsl(97).
adGenVdsl2VtucIntervalEntry row .1.3.6.1.4.1.664.5.65.1.3.3.1
An entry in the adGenVdsl2VtucIntervalTable.
Indexes
Column Syntax OID
adGenVdsl2VtucIntervalNumber
Performance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago. Intervals 2..96 are
optional.
Integer32
Constraints:
range: 1-96
 .1.3.6.1.4.1.664.5.65.1.3.3.1.1
adGenVdsl2VtucIntervalLofs
Count of seconds in the interval when there was Loss
of Framing.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.2
adGenVdsl2VtucIntervalLoss
Count of seconds in the interval when there was Loss
of Signal.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.3
adGenVdsl2VtucIntervalLols
Count of seconds in the interval when there was Loss of Link.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.4
adGenVdsl2VtucIntervalLprs
Count of seconds in the interval when there was Loss
of Power.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.5
adGenVdsl2VtucIntervalES
Count of Errored Seconds in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.6
adGenVdsl2VtucIntervalInits
Count of the line initialization attempts
during the interval. Includes both successful
and failed attempts.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.7
adGenVdsl2VtucIntervalValidData
This variable indicates if the data for this
interval is valid.
Enumeration
Enumerated Values:
1valid
2notValid
 .1.3.6.1.4.1.664.5.65.1.3.3.1.8
adGenVdsl2VtucIntervalSES
Count of Severely Errored Seconds in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.9
adGenVdsl2VtucIntervalUAS
Count of Unavailable Seconds in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.10
adGenVdsl2VtucIntervalFECs
Count of seconds in the interval during which at
least one forward error correction event took
place.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.11
adGenVdsl2VtucIntervalFEC
Count of forward error correction events that
took place in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.12
adGenVdsl2VtucIntervalCRC
Count of CRC anomolies that took place in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.13
adGenVdsl2VtucIntervalSraDownshifts
Count of SRA payload rate downshifts since last
successful train in the specified 15-min interval
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.14
adGenVdsl2VtucIntervalSraUpshifts
Count of SRA payload rate upshifts since last
successful train in the specified 15-min interval
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.15
adGenVdsl2VtucIntervalSraRateMax
Max payload rate in the specified 15-min interval
since last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.16
adGenVdsl2VtucIntervalSraRateMin
Min payload rate in the specified 15-min interval
since last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.17
adGenVdsl2VtucIntervalRtxMinEftr
Retransmission parameter defined as the minimum of
the error-free throughput rate observed in the specified
15-min interval.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.18
adGenVdsl2VtucIntervalRtxLeftrs
Count of low error-free throughput rate defect
seconds in the specified 15-min interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.3.1.19

adGenVdsl2VturIntervalTable

table
.1.3.6.1.4.1.664.5.65.1.3.4 · 1 row entry · 17 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VturIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VturIntervalTable' 
This table provides one row for each Vtur
performance data collection 1 Day interval.
VDSL2 physical interfaces are those
ifEntries where ifType is equal to vdsl(97).
adGenVdsl2VturIntervalEntry row .1.3.6.1.4.1.664.5.65.1.3.4.1
An entry in the adGenVdsl2VturIntervalTable.
Indexes
Column Syntax OID
adGenVdsl2VturIntervalNumber
Performance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago. Intervals 2..96 are
optional.
Integer32
Constraints:
range: 1-96
 .1.3.6.1.4.1.664.5.65.1.3.4.1.1
adGenVdsl2VturIntervalLofs
Count of seconds in the interval when there was
Loss of Framing.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.2
adGenVdsl2VturIntervalLoss
Count of seconds in the interval when there was
Loss of Signal.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.3
adGenVdsl2VturIntervalLprs
Count of seconds in the interval when there was
Loss of Power.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.4
adGenVdsl2VturIntervalES
Count of Errored Seconds in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.5
adGenVdsl2VturIntervalValidData
This variable indicates if the data for this
interval is valid.
Enumeration
Enumerated Values:
1valid
2notValid
 .1.3.6.1.4.1.664.5.65.1.3.4.1.6
adGenVdsl2VturIntervalSES
Count of Severely Errored Seconds in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.7
adGenVdsl2VturIntervalUAS
Count of Unavailable Seconds in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.8
adGenVdsl2VturIntervalFECs
Count of seconds in the interval during which at
least one forward error correction event took
place.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.9
adGenVdsl2VturIntervalFEC
Count of forward error correction events that
took place in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.10
adGenVdsl2VturIntervalCRC
Count of CRC anomolies that took place in
the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.11
adGenVdsl2VturIntervalSraDownshifts
Count of SRA payload rate downshifts since last
successful train in the specified 15-min interval
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.12
adGenVdsl2VturIntervalSraUpshifts
Count of SRA payload rate upshifts since last
successful train in the specified 15-min interval
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.13
adGenVdsl2VturIntervalSraRateMax
Max payload rate in the specified 15-min interval
since last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.14
adGenVdsl2VturIntervalSraRateMin
Min payload rate in the specified 15-min interval
since last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.15
adGenVdsl2VturIntervalRtxMinEftr
Retransmission parameter defined as the minimum of
the error-free throughput rate observed in the specified
15-min interval.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.16
adGenVdsl2VturIntervalRtxLeftrs
Count of low error-free throughput rate defect
seconds in the specified 15-min interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.4.1.17

adGenVdsl2VtucChanPerfDataTable

table
.1.3.6.1.4.1.664.5.65.1.3.5 · 1 row entry · 35 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VtucChanPerfDataTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VtucChanPerfDataTable' 
This table provides one row for each Vtuc channel.
VDSL2 channel interfaces can range from 1 -4
adGenVdsl2VtucChanPerfDataEntry row .1.3.6.1.4.1.664.5.65.1.3.5.1
An entry in adGenVdsl2VtucChanPerfDataTable.
Indexes
Column Syntax OID
adGenVdsl2VtucChanNumber
VDSL2 logical channel. Channel values are 1 - 4.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.3.5.1.1
adGenVdsl2VtucChanReceivedBlks
Count of all encoded blocks received on this channel
since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.2
adGenVdsl2VtucChanTransmittedBlks
Count of all encoded blocks transmitted on this
channel since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.3
adGenVdsl2VtucChanCorrectedBlks
Count of all blocks received with errors that were
corrected since agent reset. These blocks are passed
on as good data.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.4
adGenVdsl2VtucChanUncorrectBlks
Count of all blocks received with uncorrectable
errors since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.5
adGenVdsl2VtucChanPerfValidIntervals
The number of previous 15-minute intervals in the
interval table for which data was collected. Given
that <n> is the maximum # of intervals supported.
The value will be <n> unless the measurement was
(re-)started withi…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.664.5.65.1.3.5.1.6
adGenVdsl2VtucChanPerfInvalidIntervals
The number of intervals in the range from
0 to the value of adGenVdsl2VtucChanPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are n…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.664.5.65.1.3.5.1.7
adGenVdsl2VtucChanPerfCurr15MinTimeElapsed
Total elapsed seconds in this interval.
secondsUnsigned32
Constraints:
range: 0-899
 .1.3.6.1.4.1.664.5.65.1.3.5.1.8
adGenVdsl2VtucChanPerfCurr15MinReceivedBlks
Count of all encoded blocks received on this channel
within the current 15 minute interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.9
adGenVdsl2VtucChanPerfCurr15MinTransmittedBlks
Count of all encoded blocks transmitted on this
channel within the current 15 minute interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.10
adGenVdsl2VtucChanPerfCurr15MinCorrectedBlks
Count of all blocks received with errors that were
corrected on this channel within the current 15 minute
interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.11
adGenVdsl2VtucChanPerfCurr15MinUncorrectBlks
Count of all blocks received with uncorrectable
errors on this channel within the current 15 minute
interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.12
adGenVdsl2VtucChanPerfCurr1DayTimeElapsed
Number of seconds that have elapsed since the
beginning of the current 1-day interval.
secondsUnsigned32
Constraints:
range: 0-86399
 .1.3.6.1.4.1.664.5.65.1.3.5.1.13
adGenVdsl2VtucChanPerfCurr1DayReceivedBlks
Count of all encoded blocks received on this
channel during the current day as measured by


adGenVdsl2VtucChanPerfCurr1DayTimeElapsed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.14
adGenVdsl2VtucChanPerfCurr1DayTransmittedBlks
Count of all encoded blocks transmitted on this
channel during the current day as measured by
adGenVdsl2VtucChanPerfCurr1DayTimeElapsed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.15
adGenVdsl2VtucChanPerfCurr1DayCorrectedBlks
Count of all blocks received with errors that were
corrected on this channel during the current day as
measured by adGenVdsl2VtucChanPerfCurr1DayTimeElapsed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.16
adGenVdsl2VtucChanPerfCurr1DayUncorrectBlks
Count of all blocks received with uncorrectable
errors on this channel during the current day as
measured by adGenVdsl2VtucChanPerfCurr1DayTimeElapsed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.17
adGenVdsl2VtucChanPerfTcTxUnits
Count of total transmitted transmission convergence layer
(TC) cells (ATM framing mode) or packets (other framing
modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.18
adGenVdsl2VtucChanPerfTcTxDataUnits
Count of data carrying transmitted transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.19
adGenVdsl2VtucChanPerfTcTxDataOctets
Count of octets in data carrying transmitted transmission
convergence layer (TC) cells (ATM framing mode) or packets
(other framing modes).
octetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.20
adGenVdsl2VtucChanPerfTcTxIdleUnits
Count of idle/pause transmitted transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.21
adGenVdsl2VtucChanPerfTcRxUnits
Count of total transmitted transmission convergence layer
(TC) cells (ATM framing mode) or packets (other framing
modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.22
adGenVdsl2VtucChanPerfTcRxDataUnits
Count of data carrying received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.23
adGenVdsl2VtucChanPerfTcRxDataOctets
Count of octets in data carrying received transmission
convergence layer (TC) cells (ATM framing mode) or packets
(other framing modes).
octetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.24
adGenVdsl2VtucChanPerfTcRxIdleUnits
Count of idle/pause received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.25
adGenVdsl2VtucChanPerfTcRxErroredUnits
Count of errored received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.26
adGenVdsl2VtucChanPerfRtxUncorrectedDtu
Count of DTUs since reset that have been detected in error
and that have not been corrected by one or more retransmissions
within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.27
adGenVdsl2VtucChanPerfRtxCorrectedDtu
Count of DTUs since reset that have been detected in error
and that have been successfully corrected by a retransmission
within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.28
adGenVdsl2VtucChanPerfRtxRetransmittedDtu
Count of DTUs since reset that have been retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.29
adGenVdsl2VtucChanPerfCurr15MinRtxUncorrectedDtu
Count of DTUs in the current 15-min interval that have been
detected in error and that have not been corrected by one or
more retransmissions within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.30
adGenVdsl2VtucChanPerfCurr15MinRtxCorrectedDtu
Count of DTUs in the current 15-min interval that have been
detected in error and that have been successfully corrected
by a retransmission within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.31
adGenVdsl2VtucChanPerfCurr15MinRtxRetransmittedDtu
Count of DTUs in the current 15-min interval that have been
retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.32
adGenVdsl2VtucChanPerfCurr1DayRtxUncorrectedDtu
Count of DTUs in the current 24-hr interval that have been
detected in error and that have not been corrected by one or
more retransmissions within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.33
adGenVdsl2VtucChanPerfCurr1DayRtxCorrectedDtu
Count of DTUs in the current 24-hr interval that have been
detected in error and that have been successfully corrected
by a retransmission within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.34
adGenVdsl2VtucChanPerfCurr1DayRtxRetransmittedDtu
Count of DTUs in the current 24-hr interval that have been
retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.5.1.35

adGenVdsl2VturChanPerfDataTable

table
.1.3.6.1.4.1.664.5.65.1.3.6 · 1 row entry · 35 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VturChanPerfDataTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VturChanPerfDataTable' 
This table provides one row for each Vtur channel.
VDSL2 channel interfaces are those ifEntries
where ifType is equal to Interleave(124)
or Fast(125).
adGenVdsl2VturChanPerfDataEntry row .1.3.6.1.4.1.664.5.65.1.3.6.1
An entry in adGenVdsl2VturChanPerfDataTable.
Indexes
Column Syntax OID
adGenVdsl2VturChanNumber
VDSL2 logical channel. Channel values are 1 - 4.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.3.6.1.1
adGenVdsl2VturChanReceivedBlks
Count of all encoded blocks received on this channel
since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.2
adGenVdsl2VturChanTransmittedBlks
Count of all encoded blocks transmitted on this
channel since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.3
adGenVdsl2VturChanCorrectedBlks
Count of all blocks received with errors that were
corrected since agent reset. These blocks are passed
on as good data.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.4
adGenVdsl2VturChanUncorrectBlks
Count of all blocks received with uncorrectable
errors since agent reset.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.5
adGenVdsl2VturChanPerfValidIntervals
The number of previous 15-minute intervals in the
interval table for which data was collected. Given
that <n> is the maximum # of intervals supported.
The value will be <n> unless the measurement was
(re-)started withi…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.664.5.65.1.3.6.1.6
adGenVdsl2VturChanPerfInvalidIntervals
The number of intervals in the range from
0 to the value of adGenVdsl2VturChanPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are n…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.664.5.65.1.3.6.1.7
adGenVdsl2VturChanPerfCurr15MinTimeElapsed
Total elapsed seconds in this interval.
A full interval is 900 seconds.
secondsUnsigned32
Constraints:
range: 0-899
 .1.3.6.1.4.1.664.5.65.1.3.6.1.8
adGenVdsl2VturChanPerfCurr15MinReceivedBlks
Count of all encoded blocks received on this
channel within the current 15 minute interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.9
adGenVdsl2VturChanPerfCurr15MinTransmittedBlks
Count of all encoded blocks transmitted on this
channel within the current 15 minute interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.10
adGenVdsl2VturChanPerfCurr15MinCorrectedBlks
Count of all blocks received with errors that were
corrected on this channel within the current 15 minute
interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.11
adGenVdsl2VturChanPerfCurr15MinUncorrectBlks
Count of all blocks received with uncorrectable
errors on this channel within the current 15 minute
interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.12
adGenVdsl2VturChanPerfCurr1DayTimeElapsed
Number of seconds that have elapsed since the
beginning of the current 1-day interval.
secondsUnsigned32
Constraints:
range: 0-86399
 .1.3.6.1.4.1.664.5.65.1.3.6.1.13
adGenVdsl2VturChanPerfCurr1DayReceivedBlks
Count of all encoded blocks received on this
channel during the current day as measured by
adGenVdsl2VturChanPerfCurr1DayTimeElapsed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.14
adGenVdsl2VturChanPerfCurr1DayTransmittedBlks
Count of all encoded blocks transmitted on this
channel during the current day as measured by
adGenVdsl2VturChanPerfCurr1DayTimeElapsed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.15
adGenVdsl2VturChanPerfCurr1DayCorrectedBlks
Count of all blocks received with errors that were
corrected on this channel during the current day as
measured by adGenVdsl2VturChanPerfCurr1DayTimeElapsed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.16
adGenVdsl2VturChanPerfCurr1DayUncorrectBlks
Count of all blocks received with uncorrectable
errors on this channel during the current day as
measured by adGenVdsl2VturChanPerfCurr1DayTimeElapsed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.17
adGenVdsl2VturChanPerfTcTxUnits
Count of total transmitted transmission convergence layer
(TC) cells (ATM framing mode) or packets (other framing
modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.18
adGenVdsl2VturChanPerfTcTxDataUnits
Count of data carrying transmitted transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.19
adGenVdsl2VturChanPerfTcTxDataOctets
Count of octets in data carrying transmitted transmission
convergence layer (TC) cells (ATM framing mode) or packets
(other framing modes).
octetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.20
adGenVdsl2VturChanPerfTcTxIdleUnits
Count of idle/pause transmitted transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.21
adGenVdsl2VturChanPerfTcRxUnits
Count of total transmitted transmission convergence layer
(TC) cells (ATM framing mode) or packets (other framing
modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.22
adGenVdsl2VturChanPerfTcRxDataUnits
Count of data carrying received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.23
adGenVdsl2VturChanPerfTcRxDataOctets
Count of octets in data carrying received transmission
convergence layer (TC) cells (ATM framing mode) or packets
(other framing modes).
octetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.24
adGenVdsl2VturChanPerfTcRxIdleUnits
Count of idle/pause received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.25
adGenVdsl2VturChanPerfTcRxErroredUnits
Count of errored received transmission convergence
layer (TC) cells (ATM framing mode) or packets (other
framing modes).
pkts/cellsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.26
adGenVdsl2VturChanPerfRtxUncorrectedDtu
Count of DTUs since reset that have been detected in error
and that have not been corrected by one or more retransmissions
within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.27
adGenVdsl2VturChanPerfRtxCorrectedDtu
Count of DTUs since reset that have been detected in error
and that have been successfully corrected by a retransmission
within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.28
adGenVdsl2VturChanPerfRtxRetransmittedDtu
Count of DTUs since reset that have been retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.29
adGenVdsl2VturChanPerfCurr15MinRtxUncorrectedDtu
Count of DTUs in the current 15-min interval that have been
detected in error and that have not been corrected by one or
more retransmissions within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.30
adGenVdsl2VturChanPerfCurr15MinRtxCorrectedDtu
Count of DTUs in the current 15-min interval that have been
detected in error and that have been successfully corrected
by a retransmission within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.31
adGenVdsl2VturChanPerfCurr15MinRtxRetransmittedDtu
Count of DTUs in the current 15-min interval that have been
retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.32
adGenVdsl2VturChanPerfCurr1DayRtxUncorrectedDtu
Count of DTUs in the current 24-hr interval that have been
detected in error and that have not been corrected by one or
more retransmissions within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.33
adGenVdsl2VturChanPerfCurr1DayRtxCorrectedDtu
Count of DTUs in the current 24-hr interval that have been
detected in error and that have been successfully corrected
by a retransmission within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.34
adGenVdsl2VturChanPerfCurr1DayRtxRetransmittedDtu
Count of DTUs in the current 24-hr interval that have been
retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.6.1.35

adGenVdsl2VtucChanIntervalTable

table
.1.3.6.1.4.1.664.5.65.1.3.7 · 1 row entry · 10 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VtucChanIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VtucChanIntervalTable' 
This table provides one row for each Vtuc channel's
performance data collection interval.
VDSL2 channel interfaces are those ifEntries
where ifType is equal to Interleave(124)
or Fast(125).
adGenVdsl2VtucChanIntervalEntry row .1.3.6.1.4.1.664.5.65.1.3.7.1
An entry in the adGenVdsl2VtucIntervalTable.
Indexes
Column Syntax OID
adGenVdsl2VtucChanNum
VDSL2 logical channel. Channel values are 1 - 4.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.3.7.1.1
adGenVdsl2VtucChanIntervalNumber
Performance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago. Intervals 2..96 are
optional.
Integer32
Constraints:
range: 1-96
 .1.3.6.1.4.1.664.5.65.1.3.7.1.2
adGenVdsl2VtucChanIntervalReceivedBlks
Count of all encoded blocks received on this channel
during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.7.1.3
adGenVdsl2VtucChanIntervalTransmittedBlks
Count of all encoded blocks transmitted on this
channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.7.1.4
adGenVdsl2VtucChanIntervalCorrectedBlks
Count of all blocks received with errors that were
corrected on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.7.1.5
adGenVdsl2VtucChanIntervalUncorrectBlks
Count of all blocks received with uncorrectable
errors on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.7.1.6
adGenVdsl2VtucChanIntervalValidData
This variable indicates if the data for this
interval is valid.
Enumeration
Enumerated Values:
1valid
2notValid
 .1.3.6.1.4.1.664.5.65.1.3.7.1.7
adGenVdsl2VtucChanIntervalRtxUncorrectedDtu
Count of DTUs in the specified 15-min interval that have been
detected in error and that have not been corrected by one or
more retransmissions within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.7.1.8
adGenVdsl2VtucChanIntervalRtxCorrectedDtu
Count of DTUs in the specified 15-min interval that have been
detected in error and that have been successfully corrected
by a retransmission within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.7.1.9
adGenVdsl2VtucChanIntervalRtxRetransmittedDtu
Count of DTUs in the specified 15-min interval that have been
retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.7.1.10

adGenVdsl2VturChanIntervalTable

table
.1.3.6.1.4.1.664.5.65.1.3.8 · 1 row entry · 10 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VturChanIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VturChanIntervalTable' 
This table provides one row for each Vtur channel's
performance data collection interval.
VDSL2 channel interfaces are those ifEntries
where ifType is equal to Interleave(124)
or Fast(125).
adGenVdsl2VturChanIntervalEntry row .1.3.6.1.4.1.664.5.65.1.3.8.1
An entry in the adGenVdsl2VturIntervalTable.
Indexes
Column Syntax OID
adGenVdsl2VturChanNum
VDSL2 logical channel. Channel values are 1 - 4.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.3.8.1.1
adGenVdsl2VturChanIntervalNumber
Performance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago. Intervals 2..96 are
optional.
Integer32
Constraints:
range: 1-96
 .1.3.6.1.4.1.664.5.65.1.3.8.1.2
adGenVdsl2VturChanIntervalReceivedBlks
Count of all encoded blocks received on this channel
during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.8.1.3
adGenVdsl2VturChanIntervalTransmittedBlks
Count of all encoded blocks transmitted on this
channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.8.1.4
adGenVdsl2VturChanIntervalCorrectedBlks
Count of all blocks received with errors that were
corrected on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.8.1.5
adGenVdsl2VturChanIntervalUncorrectBlks
Count of all blocks received with uncorrectable
errors on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.8.1.6
adGenVdsl2VturChanIntervalValidData
This variable indicates if the data for this
interval is valid.
Enumeration
Enumerated Values:
1valid
2notValid
 .1.3.6.1.4.1.664.5.65.1.3.8.1.7
adGenVdsl2VturChanIntervalRtxUncorrectedDtu
Count of DTUs in the specified 15-min interval that have been
detected in error and that have not been corrected by one or
more retransmissions within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.8.1.8
adGenVdsl2VturChanIntervalRtxCorrectedDtu
Count of DTUs in the specified 15-min interval that have been
detected in error and that have been successfully corrected
by a retransmission within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.8.1.9
adGenVdsl2VturChanIntervalRtxRetransmittedDtu
Count of DTUs in the specified 15-min interval that have been
retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.8.1.10

adGenVdsl2Vtuc1DayIntervalTable

table
.1.3.6.1.4.1.664.5.65.1.3.9 · 1 row entry · 19 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2Vtuc1DayIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2Vtuc1DayIntervalTable' 
This table provides one row for each Vtuc
performance data collection 1 day interval.
VDSL2 physical interfaces are
those ifEntries where ifType is equal to vdsl(97).
adGenVdsl2Vtuc1DayIntervalEntry row .1.3.6.1.4.1.664.5.65.1.3.9.1
An entry in the adGenVdsl2Vtuc1DayIntervalTable.
Indexes
Column Syntax OID
adGenVdsl2Vtuc1DayIntervalNumber
Performance Data Interval number 1 is the
the most recent previous 1 day interval;
interval 7 is 7 Days ago. Intervals 1..7 are
optional.
Integer32
Constraints:
range: 1-7
 .1.3.6.1.4.1.664.5.65.1.3.9.1.1
adGenVdsl2Vtuc1DayIntervalLofs
Count of seconds in the interval when there was Loss
of Framing.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.2
adGenVdsl2Vtuc1DayIntervalLoss
Count of seconds in the 1 Day interval when there was Loss
of Signal.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.3
adGenVdsl2Vtuc1DayIntervalLols
Count of seconds in the 1 Day interval when there was
Loss of Link.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.4
adGenVdsl2Vtuc1DayIntervalLprs
Count of seconds in the 1 Day interval when there was Loss
of Power.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.5
adGenVdsl2Vtuc1DayIntervalES
Count of Errored Seconds in the interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.6
adGenVdsl2Vtuc1DayIntervalInits
Count of the line initialization attempts
during the 1 Day interval. Includes both successful
and failed attempts.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.7
adGenVdsl2Vtuc1DayIntervalValidData
This variable indicates if the data for this 1 Day
interval is valid.
Enumeration
Enumerated Values:
1valid
2notValid
 .1.3.6.1.4.1.664.5.65.1.3.9.1.8
adGenVdsl2Vtuc1DayIntervalSES
Count of Severely Errored Seconds in the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.9
adGenVdsl2Vtuc1DayIntervalUAS
Count of Unavailable Seconds in the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.10
adGenVdsl2Vtuc1DayIntervalFECs
Count of seconds in the interval during which at
least one forward error correction event took
place.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.11
adGenVdsl2Vtuc1DayIntervalFEC
Count of forward error correction events that
took place in the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.12
adGenVdsl2Vtuc1DayIntervalCRC
Count of CRC anomolies that took place in the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.13
adGenVdsl2Vtuc1DayIntervalSraDownshifts
Count of SRA payload rate downshifts since last
successful train in the specified 24-hr interval
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.14
adGenVdsl2Vtuc1DayIntervalSraUpshifts
Count of SRA payload rate upshifts since last
successful train in the specified 24-hr interval
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.15
adGenVdsl2Vtuc1DayIntervalSraRateMax
Max payload rate in the specified 24-hr interval
since last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.16
adGenVdsl2Vtuc1DayIntervalSraRateMin
Min payload rate in the specified 24-hr interval
since last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.17
adGenVdsl2Vtuc1DayIntervalRtxMinEftr
Retransmission parameter defined as the minimum of
the error-free throughput rate observed in the specified
24-hr interval.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.18
adGenVdsl2Vtuc1DayIntervalRtxLeftrs
Count of low error-free throughput rate defect
seconds in the specified 24-hr interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.9.1.19

adGenVdsl2Vtur1DayIntervalTable

table
.1.3.6.1.4.1.664.5.65.1.3.10 · 1 row entry · 17 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2Vtur1DayIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2Vtur1DayIntervalTable' 
This table provides one row for each Vtur
performance data collection 1 Day interval.
VDSL2 physical interfaces are those
ifEntries where ifType is equal to vdsl(97).
adGenVdsl2Vtur1DayIntervalEntry row .1.3.6.1.4.1.664.5.65.1.3.10.1
An entry in the adGenVdsl2Vtur1DayIntervalTable.
Indexes
Column Syntax OID
adGenVdsl2Vtur1DayIntervalNumber
Performance Data Interval number 1 is the
the most recent previous 1 day interval;
interval 7 is 7 Days ago. Intervals 1..7 are
optional.
Integer32
Constraints:
range: 1-7
 .1.3.6.1.4.1.664.5.65.1.3.10.1.1
adGenVdsl2Vtur1DayIntervalLofs
Count of seconds in the 1 Day interval when there was
Loss of Framing.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.2
adGenVdsl2Vtur1DayIntervalLoss
Count of seconds in the 1 Day interval when there was
Loss of Signal.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.3
adGenVdsl2Vtur1DayIntervalLprs
Count of seconds in the 1 Day interval when there was
Loss of Power.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.4
adGenVdsl2Vtur1DayIntervalES
Count of Errored Seconds in the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.5
adGenVdsl2Vtur1DayIntervalValidData
This variable indicates if the data for this 1 Day
interval is valid.
Enumeration
Enumerated Values:
1valid
2notValid
 .1.3.6.1.4.1.664.5.65.1.3.10.1.6
adGenVdsl2Vtur1DayIntervalSES
Count of Severely Errored Seconds in the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.7
adGenVdsl2Vtur1DayIntervalUAS
Count of Unavailable Seconds in the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.8
adGenVdsl2Vtur1DayIntervalFECs
Count of seconds in the 1 Day interval during which at
least one forward error correction event took
place.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.9
adGenVdsl2Vtur1DayIntervalFEC
Count of forward error correction events that
took place in the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.10
adGenVdsl2Vtur1DayIntervalCRC
Count of CRC anomolies that took place in
the 1 Day interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.11
adGenVdsl2Vtur1DayIntervalSraDownshifts
Count of SRA payload rate downshifts since last
successful train in the specified 24-hr interval
downshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.12
adGenVdsl2Vtur1DayIntervalSraUpshifts
Count of SRA payload rate upshifts since last
successful train in the specified 24-hr interval
upshiftsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.13
adGenVdsl2Vtur1DayIntervalSraRateMax
Max payload rate in the specified 24-hr interval
since last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.14
adGenVdsl2Vtur1DayIntervalSraRateMin
Min payload rate in the specified 24-hr interval
since last successful train.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.15
adGenVdsl2Vtur1DayIntervalRtxMinEftr
Retransmission parameter defined as the minimum of
the error-free throughput rate observed in the specified
24-hr interval.
bpsSNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.16
adGenVdsl2Vtur1DayIntervalRtxLeftrs
Count of low error-free throughput rate defect
seconds in the specified 24-hr interval.
secondsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.10.1.17

adGenVdsl2VtucChan1DayIntervalTable

table
.1.3.6.1.4.1.664.5.65.1.3.11 · 1 row entry · 10 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VtucChan1DayIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VtucChan1DayIntervalTable' 
This table provides one row for each Vtuc channel's
performance data daily collection intervals.
VDSL2 channel interfaces are those ifEntries
where ifType is equal to Interleave(124)
or Fast(125).
adGenVdsl2VtucChan1DayIntervalEntry row .1.3.6.1.4.1.664.5.65.1.3.11.1
An entry in the adGenVdsl2Vtuc1DayIntervalTable.
Indexes
Column Syntax OID
adGenVdsl2Vtuc1DayChanNum
VDSL2 logical channel. Channel values are 1 - 4.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.3.11.1.1
adGenVdsl2VtucChan1DayIntervalNumber
Performance Data Interval number 1 is the
the most recent previous interval; interval
7 is 1 week ago. Intervals 2..7 are
optional.
Integer32
Constraints:
range: 1-7
 .1.3.6.1.4.1.664.5.65.1.3.11.1.2
adGenVdsl2VtucChan1DayIntervalReceivedBlks
Count of all encoded blocks received on this channel
during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.11.1.3
adGenVdsl2VtucChan1DayIntervalTransmittedBlks
Count of all encoded blocks transmitted on this
channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.11.1.4
adGenVdsl2VtucChan1DayIntervalCorrectedBlks
Count of all blocks received with errors that were
corrected on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.11.1.5
adGenVdsl2VtucChan1DayIntervalUncorrectBlks
Count of all blocks received with uncorrectable
errors on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.11.1.6
adGenVdsl2VtucChan1DayIntervalValidData
This variable indicates if the data for this
interval is valid.
Enumeration
Enumerated Values:
1valid
2notValid
 .1.3.6.1.4.1.664.5.65.1.3.11.1.7
adGenVdsl2VtucChan1DayIntervalRtxUncorrectedDtu
Count of DTUs in the specified 24-hr interval that have been
detected in error and that have not been corrected by one or
more retransmissions within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.11.1.8
adGenVdsl2VtucChan1DayIntervalRtxCorrectedDtu
Count of DTUs in the specified 24-hr interval that have been
detected in error and that have been successfully corrected
by a retransmission within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.11.1.9
adGenVdsl2VtucChan1DayIntervalRtxRetransmittedDtu
Count of DTUs in the specified 24-hr interval that have been
retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.11.1.10

adGenVdsl2VturChan1DayIntervalTable

table
.1.3.6.1.4.1.664.5.65.1.3.12 · 1 row entry · 10 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2VturChan1DayIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2VturChan1DayIntervalTable' 
This table provides one row for each Vtur channel's
performance data daily collection interval.
VDSL2 channel interfaces are those ifEntries
where ifType is equal to Interleave(124)
or Fast(125).
adGenVdsl2VturChan1DayIntervalEntry row .1.3.6.1.4.1.664.5.65.1.3.12.1
An entry in the adGenVdsl2Vtur1DayIntervalTable.
Indexes
Column Syntax OID
adGenVdsl2Vtur1DayChanNum
VDSL2 logical channel. Channel values are 1 - 4.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.664.5.65.1.3.12.1.1
adGenVdsl2VturChan1DayIntervalNumber
Performance Data Interval number 1 is the
the most recent previous interval; interval
7 is 1 week ago. Intervals 2..7 are
optional.
Integer32
Constraints:
range: 1-7
 .1.3.6.1.4.1.664.5.65.1.3.12.1.2
adGenVdsl2VturChan1DayIntervalReceivedBlks
Count of all encoded blocks received on this channel
during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.12.1.3
adGenVdsl2VturChan1DayIntervalTransmittedBlks
Count of all encoded blocks transmitted on this
channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.12.1.4
adGenVdsl2VturChan1DayIntervalCorrectedBlks
Count of all blocks received with errors that were
corrected on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.12.1.5
adGenVdsl2VturChan1DayIntervalUncorrectBlks
Count of all blocks received with uncorrectable
errors on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.12.1.6
adGenVdsl2VturChan1DayIntervalValidData
This variable indicates if the data for this
interval is valid.
Enumeration
Enumerated Values:
1valid
2notValid
 .1.3.6.1.4.1.664.5.65.1.3.12.1.7
adGenVdsl2VturChan1DayIntervalRtxUncorrectedDtu
Count of DTUs in the specified 24-hr interval that have been
detected in error and that have not been corrected by one or
more retransmissions within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.12.1.8
adGenVdsl2VturChan1DayIntervalRtxCorrectedDtu
Count of DTUs in the specified 24-hr interval that have been
detected in error and that have been successfully corrected
by a retransmission within the maximum delay constraint.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.12.1.9
adGenVdsl2VturChan1DayIntervalRtxRetransmittedDtu
Count of DTUs in the specified 24-hr interval that have been
retransmitted.
dtusSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.3.12.1.10

adGenVdsl2ConfProfileExtTable

table
.1.3.6.1.4.1.664.5.65.1.5.1 · 1 row entry · 5 columns
Open in standard view
Uses the adtran variant from /opt/observium/mibs/adtran.
Command help
Walk adGenVdsl2ConfProfileExtTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ADTRAN-GENVDSL2-LINE-MIB' -M '/opt/observium/mibs/adtran:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ADTRAN-GENVDSL2-LINE-MIB::adGenVdsl2ConfProfileExtTable' 
This table contains VDSL management profile configuration
information not defined in the adGenVdsl2LineConfProfileTable
from the VDSL-LINE-MIB.
adGenVdsl2ConfProfileExtEntry row .1.3.6.1.4.1.664.5.65.1.5.1.1
An entry extends the adslLineConfProfileEntry
defined in VDSL-LINE-MIB. Each entry corresponds
to an VDSL line profile.
Indexes
Column Syntax OID
adGenVdsl2LineManagementProfileNameApplied
Management profile name applied to the VDSL Port profile.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.5.1.1.1
adGenVdsl2LineManagementProfileIndexApplied
Management profile name applied to the VDSL Port profile.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.664.5.65.1.5.1.1.2
adGenVdsl2LineCircuitID
Circuit ID assigned to VDSL Port.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.664.5.65.1.5.1.1.3
adGenVdsl2LineResetCounters
Selection of counter types to reset/clear for the indexed interface.
The counter types are performance monitoring intervals (PM history)
which typically consist of 15 minute/24 hour interval data,
current counters, near…
Enumerationr/w
Enumerated Values:
1all
2pmhistory
3current
4retrainne
5retrainfe
6rolling
 .1.3.6.1.4.1.664.5.65.1.5.1.1.4
adGenVdsl2LineRetrainRequest
Request the selected line to perform a full retrain/init or a
fast retrain/init. A read will always return full(1).
Enumerationr/w
Enumerated Values:
1full
2fast
 .1.3.6.1.4.1.664.5.65.1.5.1.1.5