ADTRAN-GENETHLBK-MIB Table View

This table is used for provisioning at the element level.

adGenEthLbkElementProvEntry row .1.3.6.1.4.1.664.5.70.50.2.1.1

An entry in the element provisioning table.

Indexes

adGenEthLbkElementIndex

Column	Syntax	OID
adGenEthLbkElementIndex Index used to access an element in the system. While the type is InterfaceIndex, the value contained refers to an element rather than an interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.70.50.2.1.1.1
adGenEthLbkElementLastFacCreateError This object contains the error encountered during the last failed facility loopback creation attempt. A blank string indicates no failure has occured.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.50.2.1.1.2
adGenEthLbkElementLastTermCreateError This object contains the error encountered during the last failed terminal loopback creation attempt. A blank string indicates no failure has occured.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.50.2.1.1.3

This table is used for provisioning of a facility Ethernet loopback
In a facility loopback, a flow ingressing the specified MEN port is turned back toward
that MEN port immediately upon entering the switch fabric.  Prior to egress, the source
and destination MAC addresses are swapped.

adGenEthLbkFacProvEntry row .1.3.6.1.4.1.664.5.70.50.2.2.1

An entry in the facility loopback provisioning table.

Indexes

adGenEthLbkElementIndex adGenEthLbkFacName

Column	Syntax	OID
adGenEthLbkFacName Name of the facility Ethernet loopback. This name is unique amongst all facility loopbacks residing on an element.	OctetString Constraints: range: 1-50	.1.3.6.1.4.1.664.5.70.50.2.2.1.1
adGenEthLbkFacRowStatus This object is used to create a new loopback or modify or delete an existing loopback.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.664.5.70.50.2.2.1.2
adGenEthLbkFacAdminState This object is used to control the administrative state of the loopback.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.664.5.70.50.2.2.1.3
adGenEthLbkFacRunningStatus The current status of the loopback. If the status is notRunning(2), adGenEthLbkFacRunningStatusString will contain the reason.	Enumeration Enumerated Values: 0 disabled 1 running 2 notRunning	.1.3.6.1.4.1.664.5.70.50.2.2.1.4
adGenEthLbkFacRunningStatusString A string representation of the current status. If adGenEthLbkFacRunningStatus returns notRunning(2), this object will contain the reason it isn't running.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.50.2.2.1.5
adGenEthLbkFacInterface The interface the loopback is to be applied to. The specified interface must be configured as an active MEN port, i.e. connected to a running EVC. Traffic ingressing this interface that matches specified criteria will…	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.664.5.70.50.2.2.1.6
adGenEthLbkFacMatchStag The value of the s-tag used to filter out the loopback traffic. A value of -1 indicates the traffic isn't being filtered by an s-tag value.	Integer32r/w Constraints: range: -1--1 range: 2-4094	.1.3.6.1.4.1.664.5.70.50.2.2.1.7
adGenEthLbkFacMatchPbit The value of the p-bit used to filter out the loopback traffic. A value of -1 indicates the traffic isn't being filtered by a p-bit value.	Integer32r/w Constraints: range: -1-7	.1.3.6.1.4.1.664.5.70.50.2.2.1.8
adGenEthLbkFacMatchMACDAExplicit The value of the destination MAC address used to filter out the loopback traffic. If adGenEthLbkFacMatchMACDAMode is not set to explicit(1), then the value of this object is meaningless.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.664.5.70.50.2.2.1.9
adGenEthLbkFacMatchMACDAMode This object specifies how/if a specified MAC address is being used as a loopback traffic filter. none(0) means no MAC address is being used explicit(1) means the MAC address specified in adGenEthLbkFacMatchMACDAExplicit…	Enumerationr/w Enumerated Values: 0 none 1 explicit 2 system	.1.3.6.1.4.1.664.5.70.50.2.2.1.10
adGenEthLbkFacMatchMACSAExplicit The value of the source MAC address used to filter out the loopback traffic. If adGenEthLbkFacMatchMACSAMode is not set to explicit(1), then the value of this object is meaningless.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.664.5.70.50.2.2.1.11
adGenEthLbkFacMatchMACSAMode This object specifies how/if a specified MAC address is being used as a loopback traffic filter. none(0) means no MAC address is being used explicit(1) means the MAC address specified in adGenEthLbkFacMatchMACSAExplicit…	Enumerationr/w Enumerated Values: 0 none 1 explicit	.1.3.6.1.4.1.664.5.70.50.2.2.1.12

This table is used for provisioning of a terminal Ethernet loopback
In a terminal loopback, a flow is turned back at the UNI prior to where that flow would otherwise
egress the UNI.  Prior to egress into the MEN, the source and destination MAC addresses are swapped.

adGenEthLbkTermProvEntry row .1.3.6.1.4.1.664.5.70.50.2.3.1

An entry in the terminal loopback provisioning table.

Indexes

adGenEthLbkElementIndex adGenEthLbkTermName

Column	Syntax	OID
adGenEthLbkTermName Name of the terminal Ethernet loopback. This name is unique amongst all terminal loopbacks residing on an element.	OctetString Constraints: range: 1-50	.1.3.6.1.4.1.664.5.70.50.2.3.1.1
adGenEthLbkTermRowStatus This object is used to create a new loopback or modify or delete an existing loopback.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.664.5.70.50.2.3.1.2
adGenEthLbkTermAdminState This object is used to control the administrative state of the loopback.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.664.5.70.50.2.3.1.3
adGenEthLbkTermRunningStatus The current status of the loopback. If the status is notRunning(2), adGenEthLbkTermRunningStatusString will contain the reason.	Enumeration Enumerated Values: 0 disabled 1 running 2 notRunning	.1.3.6.1.4.1.664.5.70.50.2.3.1.4
adGenEthLbkTermRunningStatusString A string representation of the current status. If adGenEthLbkTermRunningStatus returns notRunning(2), this object will contain the reason it isn't running.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.50.2.3.1.5
adGenEthLbkTermInterface The interface the loopback is to be applied to. The specified interface must be configured as an active UNI port, i.e. connected to a running EVC-map. Traffic that matches specified criteria that normally would egress…	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.664.5.70.50.2.3.1.6
adGenEthLbkTermMatchStag The value of the s-tag used to filter out the loopback traffic. A value of -1 indicates the traffic isn't being filtered by an s-tag value.	Integer32r/w Constraints: range: -1--1 range: 2-4094	.1.3.6.1.4.1.664.5.70.50.2.3.1.7
adGenEthLbkTermMatchPbit The value of the p-bit used to filter out the loopback traffic. A value of -1 indicates the traffic isn't being filtered by a p-bit value.	Integer32r/w Constraints: range: -1-7	.1.3.6.1.4.1.664.5.70.50.2.3.1.8
adGenEthLbkTermMatchMACDAExplicit The value of the destination MAC address used to filter out the loopback traffic. If adGenEthLbkTermMatchMACDAMode is not set to explicit(1), then the value of this object is meaningless.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.664.5.70.50.2.3.1.9
adGenEthLbkTermMatchMACDAMode This object specifies how/if a specified MAC address is being used as a loopback traffic filter. none(0) means no MAC address is being used explicit(1) means the MAC address specified in adGenEthLbkTermMatchMACDAExplici…	Enumerationr/w Enumerated Values: 0 none 1 explicit 2 system	.1.3.6.1.4.1.664.5.70.50.2.3.1.10
adGenEthLbkTermMatchMACSAExplicit The value of the source MAC address used to filter out the loopback traffic. If adGenEthLbkTermMatchMACSAMode is not set to explicit(1), then the value of this object is meaningless.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.664.5.70.50.2.3.1.11
adGenEthLbkTermMatchMACSAMode This object specifies how/if a specified MAC address is being used as a loopback traffic filter. none(0) means no MAC address is being used explicit(1) means the MAC address specified in adGenEthLbkTermMatchMACSAExplici…	Enumerationr/w Enumerated Values: 0 none 1 explicit	.1.3.6.1.4.1.664.5.70.50.2.3.1.12