ADSL2-LINE-MIB Table View

The table adsl2LineTable contains configuration,
command, and status parameters of the ADSL2 line.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238).
          
Several objects in this table MUST be maintained in a
persistent manner.

adsl2LineEntry row .1.3.6.1.2.1.10.238.1.1.1.1

The table adsl2LineTable contains configuration,
commands, and status parameters of the ADSL2 line

Indexes

IF-MIBifIndex

Column	Syntax	OID
adsl2LineCnfgTemplate The value of this object identifies the row in the ADSL2 Line Configuration Templates Table, (adsl2LineConfTemplateTable), which applies for this ADSL2 line. This object MUST be maintained in a persistent…	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.1.1.1.1
adsl2LineAlarmCnfgTemplate The value of this object identifies the row in the ADSL2 Line Alarm Configuration Template Table, (adsl2LineAlarmConfTemplateTable), which applies to this ADSL2 line. This object MUST be maintained in a p…	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.1.1.1.2
adsl2LineCmndConfPmsf Power management state forced. Defines the line states to be forced by the near-end ATU on this line. The various possible values are: l3toL0(0), l0toL2(2), or l0orL2toL3(3). This object MUST b…	ADSL2-LINE-TC-MIBAdsl2ConfPmsForcer/w Type Values: 0 l3toL0 2 l0toL2 3 l0orL2toL3	.1.3.6.1.2.1.10.238.1.1.1.1.3
adsl2LineCmndConfLdsf Loop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line or only be responsive to loop diagnostics initiated by the far-end ATU. …	ADSL2-LINE-TC-MIBAdsl2LineLdsfr/w Type Values: 0 inhibit 1 force	.1.3.6.1.2.1.10.238.1.1.1.1.4
adsl2LineCmndConfLdsfFailReason The status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Possible values are: none(1) - The default value in case LDSF was never requ…	ADSL2-LINE-TC-MIBAdsl2LdsfResult Type Values: 1 none 2 success 3 inProgress 4 unsupported 5 cannotRun 6 aborted 7 failed 8 illegalMode 9 adminUp 10 tableFull 11 noResources	.1.3.6.1.2.1.10.238.1.1.1.1.5
adsl2LineCmndAutomodeColdStart Automode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' indicates a c…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.238.1.1.1.1.6
adsl2LineStatusAtuTransSys The ATU Transmission System (ATS) in use. It is coded in a bit-map representation with only a single bit set to '1' (the selected coding for the ADSL line). This parameter may be derived from the handshaking procedures…	ADSL2-LINE-TC-MIBAdsl2TransmissionModeType Type Values: 0 ansit1413 1 etsi 2 g9921PotsNonOverlapped 3 g9921PotsOverlapped 4 g9921IsdnNonOverlapped 5 g9921isdnOverlapped 6 g9921tcmIsdnNonOverlapped 7 g9921tcmIsdnOverlapped 8 g9922potsNonOverlapped 9 g9922potsOverlapped 10 g9922tcmIsdnNonOverlapped 11 g9922tcmIsdnOverlapped 12 g9921tcmIsdnSymmetric 13 reserved1 14 reserved2 15 reserved3 16 reserved4 17 reserved5 18 g9923PotsNonOverlapped 19 g9923PotsOverlapped 20 g9923IsdnNonOverlapped 21 g9923isdnOverlapped 22 reserved6 23 reserved7 24 g9924potsNonOverlapped 25 g9924potsOverlapped 26 reserved8 27 reserved9 28 g9923AnnexIAllDigNonOverlapped 29 g9923AnnexIAllDigOverlapped 30 g9923AnnexJAllDigNonOverlapped 31 g9923AnnexJAllDigOverlapped 32 g9924AnnexIAllDigNonOverlapped 33 g9924AnnexIAllDigOverlapped 34 g9923AnnexLMode1NonOverlapped 35 g9923AnnexLMode2NonOverlapped 36 g9923AnnexLMode3Overlapped 37 g9923AnnexLMode4Overlapped 38 g9923AnnexMPotsNonOverlapped 39 g9923AnnexMPotsOverlapped 40 g9925PotsNonOverlapped 41 g9925PotsOverlapped 42 g9925IsdnNonOverlapped 43 g9925isdnOverlapped 44 reserved10 45 reserved11 46 g9925AnnexIAllDigNonOverlapped 47 g9925AnnexIAllDigOverlapped 48 g9925AnnexJAllDigNonOverlapped 49 g9925AnnexJAllDigOverlapped 50 g9925AnnexMPotsNonOverlapped 51 g9925AnnexMPotsOverlapped 52 reserved12 53 reserved13 54 reserved14 55 reserved15	.1.3.6.1.2.1.10.238.1.1.1.1.7
adsl2LineStatusPwrMngState The current power management state. One of four possible power management states: L0 - Synchronized and full transmission (i.e., Showtime). L1 - Low Power with reduced net data rate (G.992.2 only). L2 - Low Po…	ADSL2-LINE-TC-MIBAdsl2PowerMngState Type Values: 1 l0 2 l1 3 l2 4 l3	.1.3.6.1.2.1.10.238.1.1.1.1.8
adsl2LineStatusInitResult Indicates the result of the last full initialization performed on the line. It is an enumeration type with the following values: noFail(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), or otherCause…	ADSL2-LINE-TC-MIBAdsl2InitResult Type Values: 0 noFail 1 configError 2 configNotFeasible 3 commFail 4 noPeerAtu 5 otherCause	.1.3.6.1.2.1.10.238.1.1.1.1.9
adsl2LineStatusLastStateDs The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line.	ADSL2-LINE-TC-MIBAdsl2LastTransmittedState Type Values: 0 atucG9941 1 atucQuiet1 2 atucComb1 3 atucQuiet2 4 atucComb2 5 atucIcomb1 6 atucLineprob 7 atucQuiet3 8 atucComb3 9 atucIComb2 10 atucMsgfmt 11 atucMsgpcb 12 atucQuiet4 13 atucReverb1 14 atucTref1 15 atucReverb2 16 atucEct 17 atucReverb3 18 atucTref2 19 atucReverb4 20 atucSegue1 21 atucMsg1 22 atucReverb5 23 atucSegue2 24 atucMedley 25 atucExchmarker 26 atucMsg2 27 atucReverb6 28 atucSegue3 29 atucParams 30 atucReverb7 31 atucSegue4 32 atucShowtime 100 aturG9941 101 aturQuiet1 102 aturComb1 103 aturQuiet2 104 aturComb2 105 aturIcomb1 106 aturLineprob 107 aturQuiet3 108 aturComb3 109 aturIcomb2 110 aturMsgfmt 111 aturMsgpcb 112 aturReverb1 113 aturQuiet4 114 aturReverb2 115 aturQuiet5 116 aturReverb3 117 aturEct 118 aturReverb4 119 aturSegue1 120 aturReverb5 121 aturSegue2 122 aturMsg1 123 aturMedley 124 aturExchmarker 125 aturMsg2 126 aturReverb6 127 aturSegue3 128 aturParams 129 aturReverb7 130 aturSegue4 131 aturShowtime	.1.3.6.1.2.1.10.238.1.1.1.1.10
adsl2LineStatusLastStateUs The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line.	ADSL2-LINE-TC-MIBAdsl2LastTransmittedState Type Values: 0 atucG9941 1 atucQuiet1 2 atucComb1 3 atucQuiet2 4 atucComb2 5 atucIcomb1 6 atucLineprob 7 atucQuiet3 8 atucComb3 9 atucIComb2 10 atucMsgfmt 11 atucMsgpcb 12 atucQuiet4 13 atucReverb1 14 atucTref1 15 atucReverb2 16 atucEct 17 atucReverb3 18 atucTref2 19 atucReverb4 20 atucSegue1 21 atucMsg1 22 atucReverb5 23 atucSegue2 24 atucMedley 25 atucExchmarker 26 atucMsg2 27 atucReverb6 28 atucSegue3 29 atucParams 30 atucReverb7 31 atucSegue4 32 atucShowtime 100 aturG9941 101 aturQuiet1 102 aturComb1 103 aturQuiet2 104 aturComb2 105 aturIcomb1 106 aturLineprob 107 aturQuiet3 108 aturComb3 109 aturIcomb2 110 aturMsgfmt 111 aturMsgpcb 112 aturReverb1 113 aturQuiet4 114 aturReverb2 115 aturQuiet5 116 aturReverb3 117 aturEct 118 aturReverb4 119 aturSegue1 120 aturReverb5 121 aturSegue2 122 aturMsg1 123 aturMedley 124 aturExchmarker 125 aturMsg2 126 aturReverb6 127 aturSegue3 128 aturParams 129 aturReverb7 130 aturSegue4 131 aturShowtime	.1.3.6.1.2.1.10.238.1.1.1.1.11
adsl2LineStatusAtur Indicates current state (existing failures) of the ATU-R. This is a bit-map of possible conditions.	ADSL2-LINE-TC-MIBAdsl2LineStatus Type Values: 0 noDefect 1 lossOfFrame 2 lossOfSignal 3 lossOfPower 4 initFailure	.1.3.6.1.2.1.10.238.1.1.1.1.12
adsl2LineStatusAtuc Indicates current state (existing failures) of the ATU-C. This is a bit-map of possible conditions.	ADSL2-LINE-TC-MIBAdsl2LineStatus Type Values: 0 noDefect 1 lossOfFrame 2 lossOfSignal 3 lossOfPower 4 initFailure	.1.3.6.1.2.1.10.238.1.1.1.1.13
adsl2LineStatusLnAttenDs The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB …	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.14
adsl2LineStatusLnAttenUs The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.15
adsl2LineStatusSigAttenDs The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 1…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.16
adsl2LineStatusSigAttenUs The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 1…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.17
adsl2LineStatusSnrMarginDs Downstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-R, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (physi…	0.1 dBInteger32 Constraints: range: -640-630 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.18
adsl2LineStatusSnrMarginUs Upstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-C, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (physica…	0.1 dBInteger32 Constraints: range: -640-630 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.19
adsl2LineStatusAttainableRateDs Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the ATU-C transmitter and the ATU-R receiver, coded in bits/second.	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.1.1.1.20
adsl2LineStatusAttainableRateUs Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the ATU-R transmitter and the ATU-C receiver, coded in bits/second.	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.1.1.1.21
adsl2LineStatusActPsdDs Actual Power Spectrum Density (PSD) Downstream. The average downstream transmit PSD over the sub-carriers used for downstream. It ranges from -900 to 0 units of 0.1 dB (physical values are -90 to 0 dBm/Hz). A value of…	0.1 dBInteger32 Constraints: range: -900-0 range: 2147483647-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.22
adsl2LineStatusActPsdUs Actual Power Spectrum Density (PSD) Upstream. The average upstream transmit PSD over the sub-carriers used for upstream. It ranges from -900 to 0 units of 0.1 dB (physical values are -90 to 0 dBm/Hz). A value of 0x7FFF…	0.1 dBInteger32 Constraints: range: -900-0 range: 2147483647-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.23
adsl2LineStatusActAtpDs Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the ATU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (physical val…	0.1 dBInteger32 Constraints: range: -310-310 range: 2147483647-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.24
adsl2LineStatusActAtpUs Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB …	0.1 dBInteger32 Constraints: range: -310-310 range: 2147483647-2147483647	.1.3.6.1.2.1.10.238.1.1.1.1.25

The table adsl2ChannelStatusTable contains status
parameters of the ADSL2 channel.  This table contains live
data from equipment.

adsl2ChannelStatusEntry row .1.3.6.1.2.1.10.238.1.2.1.1

The table adsl2ChannelStatusTable contains status
parameters of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, al…

Indexes

IF-MIBifIndex adsl2ChStatusUnit

Column	Syntax	OID
adsl2ChStatusUnit The termination unit atuc(1) or atur(2).	ADSL2-LINE-TC-MIBAdsl2Unit Type Values: 1 atuc 2 atur	.1.3.6.1.2.1.10.238.1.2.1.1.1
adsl2ChStatusChannelNum Provides the bearer channel number associated with this row (i.e., the channel ifIndex). This enables determining the channel configuration profile and the channel thresholds profile applicable for this bearer channel.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.2.1.1.2
adsl2ChStatusActDataRate The actual net data rate that the bearer channel is operating at, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. The data rate is coded in bits/second.	bits/secondUnsigned32 Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.2.1.1.3
adsl2ChStatusPrevDataRate The previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fast retrain, DRA or power management transitions, excluding t…	bits/secondUnsigned32 Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.2.1.1.4
adsl2ChStatusActDelay The actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. It is coded in ms (round…	millisecondsUnsigned32 Constraints: range: 0-8176	.1.3.6.1.2.1.10.238.1.2.1.1.5
adsl2ChStatusAtmStatus Indicates the current state (existing failures) of the ADSL channel in case its Data Path is ATM. This is a bit-map of possible conditions. The various bit positions are: noDefect(0), noCellDelineation(1), or …	ADSL2-LINE-TC-MIBAdsl2ChAtmStatus Type Values: 0 noDefect 1 noCellDelineation 2 lossOfCellDelineation	.1.3.6.1.2.1.10.238.1.2.1.1.6
adsl2ChStatusPtmStatus Indicates the current state (existing failures) of the ADSL channel in case its Data Path is PTM. This is a bit-map of possible conditions. The various bit positions are: noDefect(0), or outOfSync(1). In the cas…	ADSL2-LINE-TC-MIBAdsl2ChPtmStatus Type Values: 0 noDefect 1 outOfSync	.1.3.6.1.2.1.10.238.1.2.1.1.7

The table adsl2SCStatusTable contains status parameters
of the ADSL2 sub-carriers.  The following points apply to this
table:
1.  The main purpose of this table is to hold the results
    of a DELT.
2.  This table also holds parameters obtained at line
    initialization time.
3.  The rows in this table are volatile; that is, they are
    lost if the SNMP agent is rebooted.
4.  Due to the large OCTET STRING attributes in this table,
    the worst case memory requirements for this table are
    very high.  The manager may use the row status attribute
    of this table to delete rows in order to reclaim memory.
5.  The manager may create rows in this table.  The SNMP
    agent may create rows in this table.  Only the manager
    may delete rows in this table.
6.  The maximum number of rows allowable in this table is
    indicated by the scalar attribute
    adsl2ScalarSCMaxInterfaces.
          
    The number of rows available in this table is indicated
    by the scalar attribute adsl2ScalarSCAvailInterfaces.
7.  The SNMP agent is permitted to create rows in this table
    when a DELT completes successfully or when line
    initialization occurs.  It is not mandatory for the SNMP
    agent to create rows in this table; hence, it may be
    necessary for the manager to create rows in this table
    before any results can be stored.
8.  If the manager attempts to create a row in this table
    and there are no more rows available, the creation
    attempt will fail, and the response to the SNMP SET PDU
    will contain the error noCreation(11).
9.  If the SNMP agent attempts to create a row in this table
    and there are no more rows available, the creation
    attempt will fail, and the attribute
    adsl2LineCmndConfLdsfFailReason will indicate the
    reason for the failure.  The failure reason will be either
    tableFull(10) or noResources(11).
10. An example of use of this table is as follows:
    Step 1. : The DELT is started by setting the
            : adsl2LineCmndConfLdsf from inhibit to force.
    Step 2. : The DELT completes, and valid data is
            : available.
    Step 3. : The row in the adsl2SCStatusTable where the
            : results will be stored does not yet exist so
            : the SNMP agent attempts to create the row.
    Step 4. : Due to a low memory condition, a row in the
            : adsl2SCStatusTable table cannot be created at
            : this time.
    Step 5. : The reason for the failure, tableFull(10), is
            : indicated in the adsl2LineCmndConfLdsfFailReason
            : attribute.
11. Another example of use of this table is as follows :
    Step 1. : The DELT is started by setting the
            : adsl2LineCmndConfLdsf from inhibit to force.
    Step 2. : The DELT completes and valid data is
            : available.
    Step 3. : The row in the adsl2SCStatusTable where the
            : results will be stored does not yet exist so
            : the SNMP agent attempts to create the row.
    Step 4. : The row creation is successful.
    Step 5. : The value of the attribute
            : adsl2LineCmndConfLdsfFailReasonreason is set
            : to success(2).
12. Another example of use of this table is as follows:
    Step 1. : The manager creates a row in adsl2SCStatusTable
            : for a particular ADSL2 line.
    Step 2. : The DELT is started on the above-mentioned
          
            : line by setting the adsl2LineCmndConfLdsf from
            : inhibit to force.
    Step 3. : The DELT completes, and valid data is
            : available.
    Step 4. : The value of the attribute
            : adsl2LineCmndConfLdsfFailReasonreason is set
            : to success(2).

adsl2SCStatusEntry row .1.3.6.1.2.1.10.238.1.2.2.1

The table Adsl2SCStatusEntry contains status parameters
of the ADSL2 sub-carriers.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238).

Indexes

IF-MIBifIndex adsl2SCStatusDirection

Column	Syntax	OID
adsl2SCStatusDirection The direction of the sub-carrier is either upstream or downstream.	ADSL2-LINE-TC-MIBAdsl2Direction Type Values: 1 upstream 2 downstream	.1.3.6.1.2.1.10.238.1.2.2.1.1
adsl2SCStatusMtime SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 …	symbolsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.2.2.1.2
adsl2SCStatusSnr The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers.…	OctetString Constraints: range: 0-512	.1.3.6.1.2.1.10.238.1.2.2.1.3
adsl2SCStatusBitsAlloc The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on up…	bitsOctetString Constraints: range: 0-256	.1.3.6.1.2.1.10.238.1.2.2.1.4
adsl2SCStatusGainAlloc The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream…	OctetString Constraints: range: 0-1024	.1.3.6.1.2.1.10.238.1.2.2.1.5
adsl2SCStatusTssi The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 octets with the following structure: First 2 octets - Index …	ADSL2-LINE-TC-MIBAdsl2Tssi Type Constraints: range: 0..96	.1.3.6.1.2.1.10.238.1.2.2.1.6
adsl2SCStatusLinScale The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.2.2.1.7
adsl2SCStatusLinReal An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on…	OctetString Constraints: range: 0-1024	.1.3.6.1.2.1.10.238.1.2.2.1.8
adsl2SCStatusLinImg An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on…	OctetString Constraints: range: 0-1024	.1.3.6.1.2.1.10.238.1.2.2.1.9
adsl2SCStatusLogMt The number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.2.2.1.10
adsl2SCStatusLog An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstr…	OctetString Constraints: range: 0-1024	.1.3.6.1.2.1.10.238.1.2.2.1.11
adsl2SCStatusQlnMt The number of symbols used to measure the Quiet Line Noise values on the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.2.2.1.12
adsl2SCStatusQln An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depe…	dBm/HzOctetString Constraints: range: 0-512	.1.3.6.1.2.1.10.238.1.2.2.1.13
adsl2SCStatusLnAtten When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub-carriers during diagnostics mode. When referri…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.2.2.1.14
adsl2SCStatusSigAtten When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime after the diagnostic…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.2.2.1.15
adsl2SCStatusSnrMargin SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at…	0.1 dBInteger32 Constraints: range: -640-630 range: 2147483646-2147483647	.1.3.6.1.2.1.10.238.1.2.2.1.16
adsl2SCStatusAttainableRate Maximum Attainable Data Rate. The maximum net data rate currently attainable by the ATU-C transmitter and ATU-R receiver (when referring to downstream direction) or by the ATU-R transmitter and ATU-C receiver (when ref…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.2.2.1.17
adsl2SCStatusActAtp Actual Aggregate Transmit Power from the ATU (ATU-R on downstream direction and ATU-C on upstream direction), at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (physical values are -31 to 31 dBm…	0.1 dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.10.238.1.2.2.1.18
adsl2SCStatusRowStatus Row Status. The manager may create and delete rows of this table. Please see the description of adsl2SCStatusTable above for more details.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.238.1.2.2.1.19

The table adsl2LineInventoryTable contains inventory of the
ADSL2 units.

adsl2LineInventoryEntry row .1.3.6.1.2.1.10.238.1.3.1.1

The table adsl2LineInventoryTable contains inventory of the
ADSL2 units.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238).

Indexes

IF-MIBifIndex adsl2LInvUnit

Column	Syntax	OID
adsl2LInvUnit The termination unit atuc(1) or atur(2).	ADSL2-LINE-TC-MIBAdsl2Unit Type Values: 1 atuc 2 atur	.1.3.6.1.2.1.10.238.1.3.1.1.1
adsl2LInvG994VendorId The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as defined in Recommendation T.35.	OctetString Constraints: range: 8-8	.1.3.6.1.2.1.10.238.1.3.1.1.2
adsl2LInvSystemVendorId The ATU System Vendor ID (identifies the ATU system integrator) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It con…	OctetString Constraints: range: 8-8	.1.3.6.1.2.1.10.238.1.3.1.1.3
adsl2LInvVersionNumber The ATU version number (vendor-specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of up…	OctetString Constraints: range: 0-16	.1.3.6.1.2.1.10.238.1.3.1.1.4
adsl2LInvSerialNumber The ATU serial number (vendor-specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It …	OctetString Constraints: range: 0-32	.1.3.6.1.2.1.10.238.1.3.1.1.5
adsl2LInvSelfTestResult The ATU self-test result, coded as a 32-bit value. The most significant octet of the result is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discretiona…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.3.1.1.6
adsl2LInvTransmissionCapabilities The ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATU supports the respective coding. The valu…	ADSL2-LINE-TC-MIBAdsl2TransmissionModeType Type Values: 0 ansit1413 1 etsi 2 g9921PotsNonOverlapped 3 g9921PotsOverlapped 4 g9921IsdnNonOverlapped 5 g9921isdnOverlapped 6 g9921tcmIsdnNonOverlapped 7 g9921tcmIsdnOverlapped 8 g9922potsNonOverlapped 9 g9922potsOverlapped 10 g9922tcmIsdnNonOverlapped 11 g9922tcmIsdnOverlapped 12 g9921tcmIsdnSymmetric 13 reserved1 14 reserved2 15 reserved3 16 reserved4 17 reserved5 18 g9923PotsNonOverlapped 19 g9923PotsOverlapped 20 g9923IsdnNonOverlapped 21 g9923isdnOverlapped 22 reserved6 23 reserved7 24 g9924potsNonOverlapped 25 g9924potsOverlapped 26 reserved8 27 reserved9 28 g9923AnnexIAllDigNonOverlapped 29 g9923AnnexIAllDigOverlapped 30 g9923AnnexJAllDigNonOverlapped 31 g9923AnnexJAllDigOverlapped 32 g9924AnnexIAllDigNonOverlapped 33 g9924AnnexIAllDigOverlapped 34 g9923AnnexLMode1NonOverlapped 35 g9923AnnexLMode2NonOverlapped 36 g9923AnnexLMode3Overlapped 37 g9923AnnexLMode4Overlapped 38 g9923AnnexMPotsNonOverlapped 39 g9923AnnexMPotsOverlapped 40 g9925PotsNonOverlapped 41 g9925PotsOverlapped 42 g9925IsdnNonOverlapped 43 g9925isdnOverlapped 44 reserved10 45 reserved11 46 g9925AnnexIAllDigNonOverlapped 47 g9925AnnexIAllDigOverlapped 48 g9925AnnexJAllDigNonOverlapped 49 g9925AnnexJAllDigOverlapped 50 g9925AnnexMPotsNonOverlapped 51 g9925AnnexMPotsOverlapped 52 reserved12 53 reserved13 54 reserved14 55 reserved15	.1.3.6.1.2.1.10.238.1.3.1.1.7

The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 lines.

adsl2PMLineCurrEntry row .1.3.6.1.2.1.10.238.1.4.1.1.1

The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 lines.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
te…

Indexes

IF-MIBifIndex adsl2PMLCurrUnit

Column	Syntax	OID
adsl2PMLCurrUnit The termination unit atuc(1) or atur(2).	ADSL2-LINE-TC-MIBAdsl2Unit Type Values: 1 atuc 2 atur	.1.3.6.1.2.1.10.238.1.4.1.1.1.1
adsl2PMLCurrValidIntervals Valid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.2
adsl2PMLCurrInvalidIntervals Invalid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.3
adsl2PMLCurr15MTimeElapsed Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.2.1.10.238.1.4.1.1.1.4
adsl2PMLCurr15MFecs Count of seconds during this interval where there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.5
adsl2PMLCurr15MEs Count of seconds during this interval where there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >=1 OR…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.6
adsl2PMLCurr15MSes Count of seconds during this interval where there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.7
adsl2PMLCurr15MLoss Count of seconds during this interval where there was LOS (or LOS-FE for ATU-R).	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.8
adsl2PMLCurr15MUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely-errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored secon…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.9
adsl2PMLCurr1DayValidIntervals Valid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.10
adsl2PMLCurr1DayInvalidIntervals Invalid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.11
adsl2PMLCurr1DayTimeElapsed Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.2.1.10.238.1.4.1.1.1.12
adsl2PMLCurr1DayFecs Count of seconds during this interval where there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.13
adsl2PMLCurr1DayEs Count of seconds during this interval where there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.14
adsl2PMLCurr1DaySes Count of seconds during this interval where there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-F…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.15
adsl2PMLCurr1DayLoss Count of seconds during this interval where there was LOS (or LOS-FE for ATU-R).	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.16
adsl2PMLCurr1DayUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely- errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored secon…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.1.1.17

The table adsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The PM counters in the table are not reset even when the XTU
is reinitialized.  They are reinitialized only when the
agent itself is reset or reinitialized.

adsl2PMLineCurrInitEntry row .1.3.6.1.2.1.10.238.1.4.1.2.1

The table adsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and a
terminati…

Indexes

IF-MIBifIndex

Column	Syntax	OID
adsl2PMLCurrInit15MTimeElapsed Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.1
adsl2PMLCurrInit15MFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.2
adsl2PMLCurrInit15MFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.3
adsl2PMLCurrInit15MShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.4
adsl2PMLCurrInit15MFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.5
adsl2PMLCurrInit1DayTimeElapsed Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.6
adsl2PMLCurrInit1DayFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.7
adsl2PMLCurrInit1DayFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.8
adsl2PMLCurrInit1DayShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.9
adsl2PMLCurrInit1DayFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.2.1.10

The table adsl2PMLineHist15MinTable contains PM line history
for 15min intervals of the ADSL2 line.

adsl2PMLineHist15MinEntry row .1.3.6.1.2.1.10.238.1.4.1.3.1

The table adsl2PMLineHist15MinTable contains PM line history
for 15min intervals of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with…

Indexes

IF-MIBifIndex adsl2PMLHist15MUnit adsl2PMLHist15MInterval

Column	Syntax	OID
adsl2PMLHist15MUnit The termination unit atuc(1) or atur(2).	ADSL2-LINE-TC-MIBAdsl2Unit Type Values: 1 atuc 2 atur	.1.3.6.1.2.1.10.238.1.4.1.3.1.1
adsl2PMLHist15MInterval The interval number.	Unsigned32 Constraints: range: 1-96	.1.3.6.1.2.1.10.238.1.4.1.3.1.2
adsl2PMLHist15MMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.3.1.3
adsl2PMLHist15MFecs Count of seconds during this interval where there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.3.1.4
adsl2PMLHist15MEs Count of seconds during this interval where there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.3.1.5
adsl2PMLHist15MSes Count of seconds during this interval where there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.3.1.6
adsl2PMLHist15MLoss Count of seconds during this interval where there was LOS (or LOS-FE for ATU-R).	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.3.1.7
adsl2PMLHist15MUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely- errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored secon…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.3.1.8
adsl2PMLHist15MValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.238.1.4.1.3.1.9

The table adsl2PMLineHist1DayTable contains PM line history
for 24-hour intervals of the ADSL2 line.

adsl2PMLineHist1DayEntry row .1.3.6.1.2.1.10.238.1.4.1.4.1

The table adsl2PMLineHist1DayTable contains PM line history
for 24-hour intervals of the ADSL2 line.

The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(23…

Indexes

IF-MIBifIndex adsl2PMLHist1DUnit adsl2PMLHist1DInterval

Column	Syntax	OID
adsl2PMLHist1DUnit The termination unit.	ADSL2-LINE-TC-MIBAdsl2Unit Type Values: 1 atuc 2 atur	.1.3.6.1.2.1.10.238.1.4.1.4.1.1
adsl2PMLHist1DInterval The interval number.	Unsigned32 Constraints: range: 1-30	.1.3.6.1.2.1.10.238.1.4.1.4.1.2
adsl2PMLHist1DMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.4.1.3
adsl2PMLHist1DFecs Count of seconds during this interval where there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.4.1.4
adsl2PMLHist1DEs Count of seconds during this interval where there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.4.1.5
adsl2PMLHist1DSes Count of seconds during this interval where there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >> 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.4.1.6
adsl2PMLHist1DLoss Count of seconds during this interval where there was LOS (or LOS-FE for ATU-R).	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.4.1.7
adsl2PMLHist1DUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely- errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored secon…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.4.1.8
adsl2PMLHist1DValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.238.1.4.1.4.1.9

The table adsl2PMLineInitHist15MinTable contains PM line
initialization history for 15-minute intervals of the ADSL2
line.

adsl2PMLineInitHist15MinEntry row .1.3.6.1.2.1.10.238.1.4.1.5.1

The table adsl2PMLineInitHist15MinTable contains PM line

initialization history for 15 minutes intervals of the ADSL2
line.
The index of this table consists of an interface index, where
the interface has an…

Indexes

IF-MIBifIndex adsl2PMLHistInit15MInterval

Column	Syntax	OID
adsl2PMLHistInit15MInterval The interval number.	Unsigned32 Constraints: range: 1-96	.1.3.6.1.2.1.10.238.1.4.1.5.1.1
adsl2PMLHistInit15MMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.5.1.2
adsl2PMLHistInit15MFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.5.1.3
adsl2PMLHistInit15MFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.5.1.4
adsl2PMLHistInit15MShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.5.1.5
adsl2PMLHistInit15MFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.5.1.6
adsl2PMLHistInit15MValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.238.1.4.1.5.1.7

The table adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals of the ADSL2
line.

adsl2PMLineInitHist1DayEntry row .1.3.6.1.2.1.10.238.1.4.1.6.1

The table adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals of the ADSL2
line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2p…

Indexes

IF-MIBifIndex adsl2PMLHistinit1DInterval

Column	Syntax	OID
adsl2PMLHistinit1DInterval The interval number.	Unsigned32 Constraints: range: 1-30	.1.3.6.1.2.1.10.238.1.4.1.6.1.1
adsl2PMLHistinit1DMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.6.1.2
adsl2PMLHistinit1DFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.6.1.3
adsl2PMLHistinit1DFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.6.1.4
adsl2PMLHistinit1DShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.6.1.5
adsl2PMLHistinit1DFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.1.6.1.6
adsl2PMLHistinit1DValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.238.1.4.1.6.1.7

The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized.

adsl2PMChCurrEntry row .1.3.6.1.2.1.10.238.1.4.2.1.1

The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a…

Indexes

IF-MIBifIndex adsl2PMChCurrUnit

Column	Syntax	OID
adsl2PMChCurrUnit The termination unit.	ADSL2-LINE-TC-MIBAdsl2Unit Type Values: 1 atuc 2 atur	.1.3.6.1.2.1.10.238.1.4.2.1.1.1
adsl2PMChCurrValidIntervals Valid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.1.1.2
adsl2PMChCurrInvalidIntervals Invalid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.1.1.3
adsl2PMChCurr15MTimeElapsed Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.2.1.10.238.1.4.2.1.1.4
adsl2PMChCurr15MCodingViolations Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) an…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.1.1.5
adsl2PMChCurr15MCorrectedBlocks Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each relat…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.1.1.6
adsl2PMChCurr1DayValidIntervals Valid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.1.1.7
adsl2PMChCurr1DayInvalidIntervals Invalid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.1.1.8
adsl2PMChCurr1DayTimeElapsed Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.2.1.10.238.1.4.2.1.1.9
adsl2PMChCurr1DayCodingViolations Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) an…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.1.1.10
adsl2PMChCurr1DayCorrectedBlocks Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each relat…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.1.1.11

The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.

adsl2PMChHist15MinEntry row .1.3.6.1.2.1.10.238.1.4.2.2.1

The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a…

Indexes

IF-MIBifIndex adsl2PMChHist15MUnit adsl2PMChHist15MInterval

Column	Syntax	OID
adsl2PMChHist15MUnit The termination unit.	ADSL2-LINE-TC-MIBAdsl2Unit Type Values: 1 atuc 2 atur	.1.3.6.1.2.1.10.238.1.4.2.2.1.1
adsl2PMChHist15MInterval The interval number.	Unsigned32 Constraints: range: 1-96	.1.3.6.1.2.1.10.238.1.4.2.2.1.2
adsl2PMChHist15MMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.2.1.3
adsl2PMChHist15MCodingViolations Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) an…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.2.1.4
adsl2PMChHist15MCorrectedBlocks Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each relat…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.2.1.5
adsl2PMChHist15MValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.238.1.4.2.2.1.6

The table adsl2PMChHist1DayTable contains PM channel history
for 1-day intervals of ADSL2.

adsl2PMChHist1DEntry row .1.3.6.1.2.1.10.238.1.4.2.3.1

The table adsl2PMChHist1DayTable contains PM channel history
for 1-day intervals of ADSL2.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL cha…

Indexes

IF-MIBifIndex adsl2PMChHist1DUnit adsl2PMChHist1DInterval

Column	Syntax	OID
adsl2PMChHist1DUnit The termination unit.	ADSL2-LINE-TC-MIBAdsl2Unit Type Values: 1 atuc 2 atur	.1.3.6.1.2.1.10.238.1.4.2.3.1.1
adsl2PMChHist1DInterval The interval number.	Unsigned32 Constraints: range: 1-30	.1.3.6.1.2.1.10.238.1.4.2.3.1.2
adsl2PMChHist1DMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.3.1.3
adsl2PMChHist1DCodingViolations Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.3.1.4
adsl2PMChHist1DCorrectedBlocks Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each relat…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.4.2.3.1.5
adsl2PMChHist1DValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.238.1.4.2.3.1.6

The table adsl2LineConfTemplateTable contains ADSL2 line
configuration templates.
          
Entries in this table MUST be maintained in a
persistent manner.

adsl2LineConfTemplateEntry row .1.3.6.1.2.1.10.238.1.5.1.1.1

The table adsl2LineConfTemplateTable contains the ADSL2 line
configuration template.
A default template with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless othe…

Indexes

adsl2LConfTempTemplateName

Column	Syntax	OID
adsl2LConfTempTemplateName This object identifies a row in this table.	OctetString Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.1.1.1.1
adsl2LConfTempLineProfile The value of this object identifies the row in the ADSL2 Line Configuration Profile Table, (adsl2LineConfProfTable), which applies for this ADSL2 line.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.1.1.1.2
adsl2LConfTempChan1ConfProfile The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #1. The channel profile name specified here must match the na…	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.1.1.1.3
adsl2LConfTempChan1RaRatioDs Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum D…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.238.1.5.1.1.1.4
adsl2LConfTempChan1RaRatioUs Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Dat…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.238.1.5.1.1.1.5
adsl2LConfTempChan2ConfProfile The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #2. If the channel is unused, then the object is set to a zero…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.238.1.5.1.1.1.6
adsl2LConfTempChan2RaRatioDs Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum D…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.238.1.5.1.1.1.7
adsl2LConfTempChan2RaRatioUs Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Dat…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.238.1.5.1.1.1.8
adsl2LConfTempChan3ConfProfile The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #3. If the channel is unused, then the object is set to a zero…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.238.1.5.1.1.1.9
adsl2LConfTempChan3RaRatioDs Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum D…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.238.1.5.1.1.1.10
adsl2LConfTempChan3RaRatioUs Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Dat…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.238.1.5.1.1.1.11
adsl2LConfTempChan4ConfProfile The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #4. If the channel is unused, then the object is set to a zero…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.238.1.5.1.1.1.12
adsl2LConfTempChan4RaRatioDs Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess o…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.238.1.5.1.1.1.13
adsl2LConfTempChan4RaRatioUs Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Dat…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.238.1.5.1.1.1.14
adsl2LConfTempRowStatus This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.238.1.5.1.1.1.15

The table adsl2LineConfProfTable contains ADSL2 line profile
configuration.
          
Entries in this table MUST be maintained in a
persistent manner.

adsl2LineConfProfEntry row .1.3.6.1.2.1.10.238.1.5.1.2.1

The table adsl2LineConfProfTable contains ADSL2 line profile
configuration.

A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless o…

Indexes

adsl2LConfProfProfileName

Column	Syntax	OID
adsl2LConfProfProfileName This object identifies a row in this table.	OctetString Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.1.2.1.1
adsl2LConfProfScMaskDs Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set…	ADSL2-LINE-TC-MIBAdsl2ScMaskDsr/w Type Constraints: range: 0..64	.1.3.6.1.2.1.10.238.1.5.1.2.1.2
adsl2LConfProfScMaskUs Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to …	ADSL2-LINE-TC-MIBAdsl2ScMaskUsr/w Type Constraints: range: 0..8	.1.3.6.1.2.1.10.238.1.5.1.2.1.3
adsl2LConfProfRfiBandsDs The subset of downstream PSD mask breakpoints that shall be used to notch an RFI band. The specific interpolation around these points is defined in G.992.5. It is a bitmap of 512 bits that allows referring to up to 512…	ADSL2-LINE-TC-MIBAdsl2RfiDsr/w Type Constraints: range: 0..64	.1.3.6.1.2.1.10.238.1.5.1.2.1.4
adsl2LConfProfRaModeDs The mode of operation of a rate-adaptive ATU-C in the transmit direction. The parameter can take three values: manual(1), raInit(2), or dynamicRa(3).	ADSL2-LINE-TC-MIBAdsl2RaModer/w Type Values: 1 manual 2 raInit 3 dynamicRa	.1.3.6.1.2.1.10.238.1.5.1.2.1.5
adsl2LConfProfRaModeUs The mode of operation of a rate-adaptive ATU-R in the transmit direction. The parameter can take three values: manual(1), raInit(2), or dynamicRa(3).	ADSL2-LINE-TC-MIBAdsl2RaModer/w Type Values: 1 manual 2 raInit 3 dynamicRa	.1.3.6.1.2.1.10.238.1.5.1.2.1.6
adsl2LConfProfRaUsNrmDs The Downstream Up-Shift Noise Margin value, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream noise margin is above this value and stays above it for more than the time specified by the adsl…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.238.1.5.1.2.1.7
adsl2LConfProfRaUsNrmUs The Upstream Up-Shift Noise Margin value, to be used when adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream noise margin is above this value and stays above it for more than the time specified by the adsl2LCo…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.238.1.5.1.2.1.8
adsl2LConfProfRaUsTimeDs The Downstream Up-Shift Time Interval, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. The interval of time that the downstream noise margin should stay above the Downstream Up-Shift Noise Ma…	secondsUnsigned32r/w Constraints: range: 0-16383	.1.3.6.1.2.1.10.238.1.5.1.2.1.9
adsl2LConfProfRaUsTimeUs The Upstream Up-Shift Time Interval, to be used when adsl2LConfProfRaModeUs is set to dynamicRa. The interval of time the upstream noise margin should stay above the Upstream Up-Shift Noise Margin before the ATU-C shal…	secondsUnsigned32r/w Constraints: range: 0-16383	.1.3.6.1.2.1.10.238.1.5.1.2.1.10
adsl2LConfProfRaDsNrmsDs The Downstream Down-Shift Noise Margin value, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream noise margin is below this value and stays below that for more than the time specified by the …	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.238.1.5.1.2.1.11
adsl2LConfProfRaDsNrmsUs The Upstream Down-Shift Noise Margin value, to be used when adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream noise margin is below this value and stays below that for more than the time specif…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.238.1.5.1.2.1.12
adsl2LConfProfRaDsTimeDs The Downstream Down-Shift Time Interval, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. The interval of time the downstream noise margin should stay below the Downstream Down-Shift Noise Margin before the …	secondsUnsigned32r/w Constraints: range: 0-16383	.1.3.6.1.2.1.10.238.1.5.1.2.1.13
adsl2LConfProfRaDsTimeUs The Upstream Down-Shift Time Interval, to be used when adsl2LConfProfRaModeUs is set to dynamicRa. The interval of time the upstream noise margin should stay below the Upstream Down-Shift Noise Margin before the ATU-C …	secondsUnsigned32r/w Constraints: range: 0-16383	.1.3.6.1.2.1.10.238.1.5.1.2.1.14
adsl2LConfProfTargetSnrmDs The minimum Noise Margin the ATU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 31…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.238.1.5.1.2.1.15
adsl2LConfProfTargetSnrmUs The minimum Noise Margin the ATU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 …	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.238.1.5.1.2.1.16
adsl2LConfProfMaxSnrmDs The maximum Noise Margin the ATU-R receiver shall try to sustain. If the Noise Margin is above this level, the ATU-R shall request that the ATU-C reduce the ATU-C transmit power to get a noise margin below this limit (…	0.1 dBUnsigned32r/w Constraints: range: 0-310 range: 2147483647-2147483647	.1.3.6.1.2.1.10.238.1.5.1.2.1.17
adsl2LConfProfMaxSnrmUs The maximum Noise Margin the ATU-C receiver shall try to sustain. If the Noise Margin is above this level, the ATU-C shall request that the ATU-R reduce the ATU-R transmit power to get a noise margin bel…	0.1 dBUnsigned32r/w Constraints: range: 0-310 range: 2147483647-2147483647	.1.3.6.1.2.1.10.238.1.5.1.2.1.18
adsl2LConfProfMinSnrmDs The minimum Noise Margin the ATU-R receiver shall tolerate. If the noise margin falls below this level, the ATU-R shall request that the ATU-C increase the ATU-C transmit power. If an increase to ATU-C transmit power is…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.238.1.5.1.2.1.19
adsl2LConfProfMinSnrmUs The minimum Noise Margin the ATU-C receiver shall tolerate. If the noise margin falls below this level, the ATU-C shall request that the ATU-R increase the ATU-R transmit power. If an increase of ATU-R transmit power is…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.238.1.5.1.2.1.20
adsl2LConfProfMsgMinUs Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in upstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps.	bits/secondUnsigned32r/w Constraints: range: 4000-63000	.1.3.6.1.2.1.10.238.1.5.1.2.1.21
adsl2LConfProfMsgMinDs Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in downstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps.	bits/secondUnsigned32r/w Constraints: range: 4000-63000	.1.3.6.1.2.1.10.238.1.5.1.2.1.22
adsl2LConfProfAtuTransSysEna ATU Transmission System Enabling (ATSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATUs may apply …	ADSL2-LINE-TC-MIBAdsl2TransmissionModeTyper/w Type Values: 0 ansit1413 1 etsi 2 g9921PotsNonOverlapped 3 g9921PotsOverlapped 4 g9921IsdnNonOverlapped 5 g9921isdnOverlapped 6 g9921tcmIsdnNonOverlapped 7 g9921tcmIsdnOverlapped 8 g9922potsNonOverlapped 9 g9922potsOverlapped 10 g9922tcmIsdnNonOverlapped 11 g9922tcmIsdnOverlapped 12 g9921tcmIsdnSymmetric 13 reserved1 14 reserved2 15 reserved3 16 reserved4 17 reserved5 18 g9923PotsNonOverlapped 19 g9923PotsOverlapped 20 g9923IsdnNonOverlapped 21 g9923isdnOverlapped 22 reserved6 23 reserved7 24 g9924potsNonOverlapped 25 g9924potsOverlapped 26 reserved8 27 reserved9 28 g9923AnnexIAllDigNonOverlapped 29 g9923AnnexIAllDigOverlapped 30 g9923AnnexJAllDigNonOverlapped 31 g9923AnnexJAllDigOverlapped 32 g9924AnnexIAllDigNonOverlapped 33 g9924AnnexIAllDigOverlapped 34 g9923AnnexLMode1NonOverlapped 35 g9923AnnexLMode2NonOverlapped 36 g9923AnnexLMode3Overlapped 37 g9923AnnexLMode4Overlapped 38 g9923AnnexMPotsNonOverlapped 39 g9923AnnexMPotsOverlapped 40 g9925PotsNonOverlapped 41 g9925PotsOverlapped 42 g9925IsdnNonOverlapped 43 g9925isdnOverlapped 44 reserved10 45 reserved11 46 g9925AnnexIAllDigNonOverlapped 47 g9925AnnexIAllDigOverlapped 48 g9925AnnexJAllDigNonOverlapped 49 g9925AnnexJAllDigOverlapped 50 g9925AnnexMPotsNonOverlapped 51 g9925AnnexMPotsOverlapped 52 reserved12 53 reserved13 54 reserved14 55 reserved15	.1.3.6.1.2.1.10.238.1.5.1.2.1.23
adsl2LConfProfPmMode Power management state Enabling. Defines the power states the ATU-C or ATU-R may autonomously transition to on this line. The various bit positions are: allowTransitionsToIdle(0) and allowTransitionsToLowPower(1). A b…	ADSL2-LINE-TC-MIBAdsl2LConfProfPmModer/w Type Values: 0 allowTransitionsToIdle 1 allowTransitionsToLowPower	.1.3.6.1.2.1.10.238.1.5.1.2.1.24
adsl2LConfProfL0Time This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds.	secondsUnsigned32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.238.1.5.1.2.1.25
adsl2LConfProfL2Time This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds.	secondsUnsigned32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.238.1.5.1.2.1.26
adsl2LConfProfL2Atpr The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB.	dBUnsigned32r/w Constraints: range: 0-31	.1.3.6.1.2.1.10.238.1.5.1.2.1.27
adsl2LConfProfL2Atprt The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims.	dBUnsigned32r/w Constraints: range: 0-31	.1.3.6.1.2.1.10.238.1.5.1.2.1.28
adsl2LConfProfRowStatus This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.238.1.5.1.2.1.29

The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific
parameters.
A row in this table that has an index of
          
adsl2LConfProfAdslMode == defMode(1) is called a
'mandatory' row.
A row in this table that has an index such that
adsl2LConfProfAdslMode is not equal to defMode(1)
is called an 'optional' row.
When a row in the adsl2LineConfProfTable table
(the parent row) is created, the SNMP agent will
automatically create a 'mandatory' row in this table.
When the parent row is deleted, the SNMP agent will
automatically delete all associated rows in this table.
Any attempt to delete the 'mandatory' row using the
adsl2LConfProfModeSpecRowStatus attribute will be
rejected by the SNMP agent.
The manager MAY create an 'optional' row in this table
using the adsl2LConfProfModeSpecRowStatus attribute if
the parent row exists.
The manager MAY delete an 'optional' row in this table
using the adsl2LConfProfModeSpecRowStatus attribute at
any time.
If the actual transmission mode of a DSL line does not
match one of the 'optional' rows in this table, then
the line will use the PSD configuration from the
'mandatory' row.
          
Entries in this table MUST be maintained in a
persistent manner.

adsl2LineConfProfModeSpecEntry row .1.3.6.1.2.1.10.238.1.5.1.3.1

The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific
parameters.

Indexes

adsl2LConfProfProfileName adsl2LConfProfAdslMode

Column	Syntax	OID
adsl2LConfProfAdslMode The ADSL Mode is a way of categorizing the various ADSL transmission modes into groups; each group (ADSL Mode) shares the same PSD configuration. There should be multiple entries in this table for a given line profile i…	ADSL2-LINE-TC-MIBAdsl2OperationModes Type Values: 1 defMode 2 adsl 8 g9923PotsNonOverlapped 9 g9923PotsOverlapped 10 g9923IsdnNonOverlapped 11 g9923isdnOverlapped 14 g9924potsNonOverlapped 15 g9924potsOverlapped 18 g9923AnnexIAllDigNonOverlapped 19 g9923AnnexIAllDigOverlapped 20 g9923AnnexJAllDigNonOverlapped 21 g9923AnnexJAllDigOverlapped 22 g9924AnnexIAllDigNonOverlapped 23 g9924AnnexIAllDigOverlapped 24 g9923AnnexLMode1NonOverlapped 25 g9923AnnexLMode2NonOverlapped 26 g9923AnnexLMode3Overlapped 27 g9923AnnexLMode4Overlapped 28 g9923AnnexMPotsNonOverlapped 29 g9923AnnexMPotsOverlapped 30 g9925PotsNonOverlapped 31 g9925PotsOverlapped 32 g9925IsdnNonOverlapped 33 g9925isdnOverlapped 36 g9925AnnexIAllDigNonOverlapped 37 g9925AnnexIAllDigOverlapped 38 g9925AnnexJAllDigNonOverlapped 39 g9925AnnexJAllDigOverlapped 40 g9925AnnexMPotsNonOverlapped 41 g9925AnnexMPotsOverlapped	.1.3.6.1.2.1.10.238.1.5.1.3.1.1
adsl2LConfProfMaxNomPsdDs The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to -30 dBm/Hz).	0.1 dBm/HzInteger32r/w Constraints: range: -600--300	.1.3.6.1.2.1.10.238.1.5.1.3.1.2
adsl2LConfProfMaxNomPsdUs The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to -30 dBm/Hz).	0.1 dBm/HzInteger32r/w Constraints: range: -600--300	.1.3.6.1.2.1.10.238.1.5.1.3.1.3
adsl2LConfProfMaxNomAtpDs The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).	0.1 dBmUnsigned32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.238.1.5.1.3.1.4
adsl2LConfProfMaxNomAtpUs The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).	0.1 dBmUnsigned32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.238.1.5.1.3.1.5
adsl2LConfProfMaxAggRxPwrUs The maximum upstream aggregate receive power over the relevant set of sub-carriers. The ATU-C should verify that the upstream power cutback is such that this maximum aggregate receive power value is honored. It ranges…	0.1 dBmInteger32r/w Constraints: range: -255-255 range: 2147483647-2147483647	.1.3.6.1.2.1.10.238.1.5.1.3.1.6
adsl2LConfProfPsdMaskDs The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a s…	ADSL2-LINE-TC-MIBAdsl2PsdMaskDsr/w Type Constraints: range: 0..96	.1.3.6.1.2.1.10.238.1.5.1.3.1.7
adsl2LConfProfPsdMaskUs The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a str…	ADSL2-LINE-TC-MIBAdsl2PsdMaskUsr/w Type Constraints: range: 0..12	.1.3.6.1.2.1.10.238.1.5.1.3.1.8
adsl2LConfProfPsdMaskSelectUs The selected upstream PSD mask. This parameter is used only for annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in adsl2LConfProfAtuTransSysEna.	Unsigned32r/w Constraints: range: 1-9	.1.3.6.1.2.1.10.238.1.5.1.3.1.9
adsl2LConfProfModeSpecRowStatus This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.238.1.5.1.3.1.10

The table adsl2ChConfProfileTable contains ADSL2 channel
profile configuration.
          
Entries in this table MUST be maintained in a
persistent manner.

adsl2ChConfProfileEntry row .1.3.6.1.2.1.10.238.1.5.2.1.1

The table adsl2ChConfProfileTable contains ADSL2 channel
profile configuration.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise …

Indexes

adsl2ChConfProfProfileName

Column	Syntax	OID
adsl2ChConfProfProfileName This object identifies a row in this table.	OctetString Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.2.1.1.1
adsl2ChConfProfMinDataRateDs Minimum Data Rate on Downstream direction. The minimum net data rate for the bearer channel, coded in bits/second.	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.2
adsl2ChConfProfMinDataRateUs Minimum Data Rate on Upstream direction. The minimum net data rate for the bearer channel, coded in bits/second.	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.3
adsl2ChConfProfMinResDataRateDs Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bits/second. This parameter is used only if the Rate Adaptation Mode in the direction of the bear…	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.4
adsl2ChConfProfMinResDataRateUs Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bits/second. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer…	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.5
adsl2ChConfProfMaxDataRateDs Maximum Data Rate on Downstream direction. The maximum net data rate for the bearer channel, coded in bits/second.	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.6
adsl2ChConfProfMaxDataRateUs Maximum Data Rate on Upstream direction. The maximum net data rate for the bearer channel, coded in bits/second.	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.7
adsl2ChConfProfMinDataRateLowPwrDs Minimum Data Rate in Low Power state on Downstream direction. The minimum net data rate for the bearer channel, coded in bits/second, during the low power state (L1 in G.992.2, L2 in G.992.3).	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.8
adsl2ChConfProfMaxDelayDs Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The ATUs shall choose the S (factor) and D (depth) values such that the actual…	millisecondsUnsigned32r/w Constraints: range: 0-63	.1.3.6.1.2.1.10.238.1.5.2.1.1.9
adsl2ChConfProfMaxDelayUs Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The ATUs shall choose the S (factor) and D (depth) values such that the actual one…	millisecondsUnsigned32r/w Constraints: range: 0-63	.1.3.6.1.2.1.10.238.1.5.2.1.1.10
adsl2ChConfProfMinProtectionDs Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not req…	symbolsADSL2-LINE-TC-MIBAdsl2SymbolProtectionr/w Type Values: 1 noProtection 2 halfSymbol 3 singleSymbol 4 twoSymbols 5 threeSymbols 6 fourSymbols 7 fiveSymbols 8 sixSymbols 9 sevenSymbols 10 eightSymbols 11 nineSymbols 12 tenSymbols 13 elevenSymbols 14 twelveSymbols 15 thirteeSymbols 16 fourteenSymbols 17 fifteenSymbols 18 sixteenSymbols	.1.3.6.1.2.1.10.238.1.5.2.1.1.11
adsl2ChConfProfMinProtectionUs Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not requi…	symbolsADSL2-LINE-TC-MIBAdsl2SymbolProtectionr/w Type Values: 1 noProtection 2 halfSymbol 3 singleSymbol 4 twoSymbols 5 threeSymbols 6 fourSymbols 7 fiveSymbols 8 sixSymbols 9 sevenSymbols 10 eightSymbols 11 nineSymbols 12 tenSymbols 13 elevenSymbols 14 twelveSymbols 15 thirteeSymbols 16 fourteenSymbols 17 fifteenSymbols 18 sixteenSymbols	.1.3.6.1.2.1.10.238.1.5.2.1.1.12
adsl2ChConfProfMaxBerDs Maximum Bit Error Ratio on Downstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7): eminus3(1), eminus5(2), or eminus7(3).	ADSL2-LINE-TC-MIBAdsl2MaxBerr/w Type Values: 1 eminus3 2 eminus5 3 eminus7	.1.3.6.1.2.1.10.238.1.5.2.1.1.13
adsl2ChConfProfMaxBerUs Maximum Bit Error Ratio on Upstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7): eminus3(1), eminus5(2), or eminus7(3).	ADSL2-LINE-TC-MIBAdsl2MaxBerr/w Type Values: 1 eminus3 2 eminus5 3 eminus7	.1.3.6.1.2.1.10.238.1.5.2.1.1.14
adsl2ChConfProfUsDataRateDs Data Rate Threshold Up shift for downstream direction. An 'Up-shift rate change' event is triggered when the actual downstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtim…	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.15
adsl2ChConfProfDsDataRateDs Data Rate Threshold Down-shift for downstream direction. A 'Down-shift rate change' event is triggered when the actual downstream data rate is below the data rate at the last entry into Showtime, by more than the thres…	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.16
adsl2ChConfProfUsDataRateUs Data Rate Threshold Up shift for upstream direction. An 'Up-shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. …	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.17
adsl2ChConfProfDsDataRateUs Data Rate Threshold Down-shift for upstream direction. A 'Down-shift rate change' event is triggered when the actual upstream data rate is below the data rate at the last entry into Showtime, by more than the threshold…	bits/secondUnsigned32r/w Constraints: range: 0-200000000	.1.3.6.1.2.1.10.238.1.5.2.1.1.18
adsl2ChConfProfImaEnabled IMA Mode Enable. The parameter enables the IMA operation mode in the ATM Data Path. Relevant only if the channel is an ATM Data Path. When in 'enable' state, the ATM data path should comply with the requirements for …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.238.1.5.2.1.1.19
adsl2ChConfProfRowStatus This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.238.1.5.2.1.1.20

The table adsl2LineAlarmConfTemplateTable contains
ADSL2 line configuration templates.
          
Entries in this table MUST be maintained in a
persistent manner.

adsl2LineAlarmConfTemplateEntry row .1.3.6.1.2.1.10.238.1.5.3.1.1

The table adsl2LineAlarmConfTemplateTable contains ADSL2
line PM thresholds templates.
A default template with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless ot…

Indexes

adsl2LAlarmConfTempTemplateName

Column	Syntax	OID
adsl2LAlarmConfTempTemplateName This object identifies a row in this table.	OctetString Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.3.1.1.1
adsl2LAlarmConfTempLineProfile The value of this object identifies the row in the ADSL2 Line Thresholds Configuration Profile Table (adsl2LineAlarmConfProfileTable) that applies to this ADSL2 line.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.3.1.1.2
adsl2LAlarmConfTempChan1ConfProfile The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #1. The channel profile name specified here m…	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.3.1.1.3
adsl2LAlarmConfTempChan2ConfProfile The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #2. The channel profile name specified here m…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.238.1.5.3.1.1.4
adsl2LAlarmConfTempChan3ConfProfile The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #3. The channel profile name specified here m…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.238.1.5.3.1.1.5
adsl2LAlarmConfTempChan4ConfProfile The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #4. The channel profile name specified here m…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.238.1.5.3.1.1.6
adsl2LAlarmConfTempRowStatus This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.238.1.5.3.1.1.7

The table adsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles.
          
 Entries in this table MUST be maintained in a
 persistent manner.

adsl2LineAlarmConfProfileEntry row .1.3.6.1.2.1.10.238.1.5.3.2.1

The table adsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless other…

Indexes

adsl2LineAlarmConfProfileName

Column	Syntax	OID
adsl2LineAlarmConfProfileName This object identifies a row in this table.	OctetString Constraints: range: 1-32	.1.3.6.1.2.1.10.238.1.5.3.2.1.1
adsl2LineAlarmConfProfileAtucThresh15MinFecs A threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.2
adsl2LineAlarmConfProfileAtucThresh15MinEs A threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.3
adsl2LineAlarmConfProfileAtucThresh15MinSes A threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.4
adsl2LineAlarmConfProfileAtucThresh15MinLoss A threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.5
adsl2LineAlarmConfProfileAtucThresh15MinUas A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.6
adsl2LineAlarmConfProfileAturThresh15MinFecs A threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.7
adsl2LineAlarmConfProfileAturThresh15MinEs A threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.8
adsl2LineAlarmConfProfileAturThresh15MinSes A threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.9
adsl2LineAlarmConfProfileAturThresh15MinLoss A threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.10
adsl2LineAlarmConfProfileAturThresh15MinUas A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.	secondsHC-PerfHist-TC-MIBHCPerfIntervalThresholdr/w Type Constraints: range: 0..900	.1.3.6.1.2.1.10.238.1.5.3.2.1.11
adsl2LineAlarmConfProfileThresh15MinFailedFullInt A threshold for the adsl2PMLCurrInit15MfailedFullInits counter. The value 0 means that no threshold is specified for the associated counter.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.5.3.2.1.12
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt A threshold for the adsl2PMLCurrInit15MFailedShortInits counter. The value 0 means that no threshold is specified for the associated counter.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.238.1.5.3.2.1.13
adsl2LineAlarmConfProfileRowStatus This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.238.1.5.3.2.1.14