ACD-SFP-MIB Table View

Unique value for each SFP. Its value ranges from 1 to
MAXINT (4 bytes).

This object identifies the connector index on the box. The index
is assigned form left to rigth starting with 1.

The connector value indicates the external optical or electrical
cable connector provided as the media interface.

The vendor name is a 16 character field that contains ASCII
characters, left-aligned and padded on the right with ASCII
spaces (20h). The vendor name shall be the full name of the
corporation, a commonly accepted abbr…

The vendor organizationally unique identifier field (vendor OUI)
is a 3-byte field that contains the IEEE Company Identifier for
the vendor. A value of all zero in the 3-byte field indicates
that the Vendor OUI is uns…

The vendor part number (vendor PN) is a 16-byte field that
contains ASCII characters, leftaligned and padded on the
right with ASCII spaces (20h), defining the vendor's part
number or product name. A value of all zero…

The vendor revision number (vendor rev) is a 4-byte field that
contains ASCII characters, leftaligned and padded on the right
with ASCII spaces (20h), defining the vendor's product revision
number. A value of all zero i…

Nominal transmitter output wavelength at room temperature. 16 bit
value with byte 60 as high order byte and byte 61 as low order
byte. The laser wavelength is equal to the 16 bit integer
value in nm. This field allows …

The vendor serial number (vendor SN) is a 16 character field that
contains ASCII characters, left-aligned and padded on the right
with ASCII spaces (20h), defining the vendor's serial number for
the transceiver. A valu…

This is the year of manufacturing.

This is the month of manufacturing.

This is the day of manufacturing.

This is the Lot number of manufacturing.

This is to indicate to which revision this SFP is compatible.

This is to indicate if the SFP is present or not.

This is to indicate if the SFP supports Digital Diagnostics.

This is to indicate if the SFP supports internal calibration. If
externally calibrated, the measurements are raw A/D values and must
be converted to real world units using calibration constants
stored in EEPROM locatio…

This is to indicate if the SFP supports Alarm and warning
thresholds for the Digital Diagnostics.

The identifier value specifies the physical device described by
the two-wire interface information. This value shall be included
in the two-wire interface data (see SFF-8472 for details).

The extended identifier value provides additional information
about the transceiver. The field should be set to 04h for all SFP
modules indicating two-wire interface ID module definition (see
SFF-8472 for details).

The following bit significant indicators define the electronic
or optical interfaces that are supported by the transceiver. At
least one bit shall be set in this field (see SFF-8472 for details).

Unique value for each SFP. Its value ranges from 1 to
MAXINT (4 bytes).

This object identifies the connector index on the box. The index
is assigned form left to rigth starting with 1.

Internally measured transceiver temperature. Represented as a
16 bit signed twos complement value in degrees Celsius, yielding
a total range of -128C to +128C.

Internally measured transceiver supply voltage. Represented as
a 16 bit unsigned integer with the voltage defined as the full
16 bit value (0 to 65535) with LSB equal to 100 micro-Volt,
yielding a total range of 0 to +6…

Measured TX bias current in micro-Amps yielding a total range of
0 to 131 mA.

Measured TX output power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40 to…

Measured Rx input power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40 to …

Measured TX output power in dBm (~ -40 to +8.2 dBm).

Measured Rx input power in dBm (~ -40 to +8.2 dBm).

Unique value for each SFP. Its value ranges from 1 to
MAXINT (4 bytes).

This object identifies the connector index on the box. The index
is assigned form left to rigth starting with 1.

High Alarm transceiver temperature. Represented as a 16 bit
signed twos complement value in degrees Celsius, yielding
a total range of -128C to +128C.

Low Alarm transceiver temperature. Represented as a 16 bit
signed twos complement value in degrees Celsius, yielding
a total range of -128C to +128C.

High Warning transceiver temperature. Represented as a 16 bit
signed twos complement value in degrees Celsius, yielding
a total range of -128C to +128C.

Low Warning transceiver temperature. Represented as a 16 bit
signed twos complement value in degrees Celsius, yielding
a total range of -128C to +128C.

High Alarm transceiver supply voltage. Represented as
a 16 bit unsigned integer with the voltage defined as the full
16 bit value (0 to 65535) with LSB equal to 100 micro-Volt,
yielding a total range of 0 to +6.55 Volts.

Low Alarm transceiver supply voltage. Represented as
a 16 bit unsigned integer with the voltage defined as the full
16 bit value (0 to 65535) with LSB equal to 100 micro-Volt,
yielding a total range of 0 to +6.55 Volts.

High Warning transceiver supply voltage. Represented as
a 16 bit unsigned integer with the voltage defined as the full
16 bit value (0 to 65535) with LSB equal to 100 micro-Volt,
yielding a total range of 0 to +6.55 Vol…

Low Warning transceiver supply voltage. Represented as
a 16 bit unsigned integer with the voltage defined as the full
16 bit value (0 to 65535) with LSB equal to 100 micro-Volt,
yielding a total range of 0 to +6.55 Volt…

High Alarm TX bias current in micro-Amps yielding a total range of
0 to 131 mA.

Low Alarm TX bias current in micro-Amps yielding a total range of
0 to 131 mA.

High Warning TX bias current in micro-Amps yielding a total range of
0 to 131 mA.

Low Warning TX bias current in micro-Amps yielding a total range of
0 to 131 mA.

High Alarm TX output power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40 …

Low Alarm TX output power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40 t…

High Warning TX output power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -4…

Low Warning TX output power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40…

High Alarm RX input power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40 t…

Low Alarm RX input power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40 to…

High Warning RX input power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40…

Low Warning RX input power in mW. Represented as a 16 bit unsigned
integer with the power defined as the full 16 bit value (0 to 65535)
with LSB equal to 0.1 micro-Watt, yielding a total range of 0
to 6.5535 mW (~ -40 …

High Alarm TX output power in dBm (~ -40 to +8.2 dBm).

Low Alarm TX output power in dBm (~ -40 to +8.2 dBm).

High Warning TX output power in dBm (~ -40 to +8.2 dBm).

Low Warning TX output power in dBm (~ -40 to +8.2 dBm).

High Alarm Rx input power in dBm (~ -40 to +8.2 dBm).

Low Alarm Rx input power in dBm (~ -40 to +8.2 dBm).

High Warning Rx input power in dBm (~ -40 to +8.2 dBm).

Low Warning Rx input power in dBm (~ -40 to +8.2 dBm).

Unique value for each SFP. Its value ranges from 1 to
MAXINT (4 bytes).

This object identifies the connector index on the box. The index
is assigned form left to rigth starting with 1.

This is to indicate if the temperature reaches or overpasses the High
alarm threshold.

This is to indicate if the temperature reaches or underpasses the Low
alarm threshold.

This is to indicate if the temperature reaches or overpasses the High
warning threshold.

This is to indicate if the temperature reaches or underpasses the Low
warning threshold.

This is to indicate if the supply voltage reaches or overpasses the High
alarm threshold.

This is to indicate if the supply voltage reaches or underpasses the Low
alarm threshold.

This is to indicate if the supply voltage reaches or overpasses the High
warning threshold.

This is to indicate if the supply voltage reaches or underpasses the Low
warning threshold.

This is to indicate if the Laser Bias Current reaches or overpasses
the High alarm threshold.

This is to indicate if the Laser Bias Current reaches or underpasses
the Low alarm threshold.

This is to indicate if the Laser Bias Current reaches or overpasses
the High warning threshold.

This is to indicate if the Laser Bias Current reaches or underpasses
the Low warning threshold.

This is to indicate if the Transmit Power reaches or overpasses the High
alarm threshold.

This is to indicate if the Transmit Power reaches or underpasses the Low
alarm threshold.

This is to indicate if the Transmit Power reaches or overpasses the High
warning threshold.

This is to indicate if the Transmit Power reaches or underpasses the Low
warning threshold.

This is to indicate if the Receive Power reaches or overpasses the High
alarm threshold.

This is to indicate if the Receive Power reaches or underpasses the Low
alarm threshold.

This is to indicate if the Receive Power reaches or overpasses the High
warning threshold.

This is to indicate if the Receive Power reaches or underpasses the Low
warning threshold.