A3Com-Bridge-r3-MIB Table View

This table is an extension of the dot1dStaticTable
from the Bridge MIB, rfc1286.  One additional
column has been defined to identify the proper wide 
area address when bridging over a wide area port.

a3ComBrgStExtEntry row .1.3.6.1.4.1.43.2.9.1.10.1

An extension to the dot1dStaticTable from rfc1286.

Indexes

a3ComBrgStExtAdd a3ComBrgStExtRcvPort

Column	Syntax	OID
a3ComBrgStExtAddmandatory A unicast MAC address for which the bridge has forwarding and/or filtering information.		.1.3.6.1.4.1.43.2.9.1.10.1.1
a3ComBrgStExtRcvPortmandatory Either the value '0' or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the bri…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.1.10.1.2
a3ComBrgStExtWaAddressmandatory When the destination port to which this table entry applies is a wide area port, this object is used to identify the wide area address to use when forwarding packets to this destination. The type of address can be det…	OctetString	.1.3.6.1.4.1.43.2.9.1.10.1.3

This table is an extension of the dot1dTpFdbTable
from the Bridge MIB, rfc1286.  One additional
column has been defined to identify the proper wide 
area address when bridging over a wide area port.

a3ComBrgFdbExtEntry row .1.3.6.1.4.1.43.2.9.1.11.1

An extension to the dot1dTpFdbTable from rfc1286.

Indexes

a3ComBrgFdbExtAdd

Column	Syntax	OID
a3ComBrgFdbExtAddmandatory A unicast MAC address for which the bridge has forwarding and/or filtering information.		.1.3.6.1.4.1.43.2.9.1.11.1.1
a3ComBrgFdbExtWaAddressmandatory When the port to which this table entry applies is a wide area port, this object is used to identify the wide area address to use when forwarding packets to this destination. The type of address can be determined by th…	OctetString	.1.3.6.1.4.1.43.2.9.1.11.1.2

This table is an extension of the dot1dBasePortTable
from the Bridge MIB defined in RFC1286.  This table
contains generic information and control facilities
for every port that is associated with the bridge.
Transparent, source-route, and srt ports are included.

a3ComBrgPortEntry row .1.3.6.1.4.1.43.2.9.1.12.1

Each entry in this table contains information and
controls for a specific bridge port.

Indexes

a3ComBrgPortIndex

Column	Syntax	OID
a3ComBrgPortIndexmandatory The port number of the port for which this entry contains bridge management information.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.1.12.1.1
a3ComBrgPortCtlmandatory This object controls which type(s) of packets are bridged. This has no affect on whether the bridge participates in either the Spanning Tree or Source Route Protocols.	Enumerationr/w Enumerated Values: 1 transparent 2 sourceRoute 3 srtEnabled 4 noBridging	.1.3.6.1.4.1.43.2.9.1.12.1.2
a3ComBrgDstSecCtlmandatory This object is a security feature that allows the control of packets sent to specific destinations. If this object is set to forward (2), only those packets for destination addresses listed in the static forwarding tabl…	Enumerationr/w Enumerated Values: 1 none 2 forward 3 block	.1.3.6.1.4.1.43.2.9.1.12.1.3
a3ComBrgSrcSecCtlmandatory This object is a security feature that allows the control of packets sent from specific source addresses. If this object is set to forward (2), this port will forward only those packets sent from addresses listed in the…	Enumerationr/w Enumerated Values: 1 none 2 forward 3 block	.1.3.6.1.4.1.43.2.9.1.12.1.4
a3ComBrgX25Pidmandatory This object applies to transparent bridging over an X25 network. It specifies the protocol ID to be used in an outgoing X25 call.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.43.2.9.1.12.1.5
a3ComBrgX25Qsizeobsolete This object applies to transparent bridging over an X25 network. It allows the specification of the maximum number of packets that can be queued on any single virtual circuit to a specific DTE neighbor when the virtu…	Integer32r/w Constraints: range: 1-128	.1.3.6.1.4.1.43.2.9.1.12.1.6
a3ComBrgX25VcLimitobsolete This object allows the specification of the maximum number of virtual circuits to a specific DTE that can be established concurrently for transparent bridging over an x25 network. NOTE: this object is n…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.9.1.12.1.7
a3ComBrgX25VcTimerobsolete This object specifies the maximum amount of time, in minutes, that can elapse when there is no activity on the x25 virtual circuit to a DTE before it is cleared. NOTE: this object is no longer supported b…	Integer32r/w Constraints: range: 1-512	.1.3.6.1.4.1.43.2.9.1.12.1.8
a3ComBrgBroadCastLimitmandatory This object specifies the maximum rate, in packets per second, at which broadcast and multicast packets are forwarded through this port. If the number of these packets during a single time interval (specified by a3Co…	Integer32r/w Constraints: range: 0-100000	.1.3.6.1.4.1.43.2.9.1.12.1.9
a3ComBrgSmdsGroupAddrmandatory This identifies the SMDS Group Address that is used by the bridge to transmit packets to all the other bridges identified by this SMDS Group Address. This address is used as the SMDS destination address when transmitti…	SMDSAddressr/w Type Constraints: range: 8	.1.3.6.1.4.1.43.2.9.1.12.1.10
a3ComBrgX25ProfIdmandatory This object specifies the X25 User ProfileID to be used for selecting a Virtual Circuit to send Bridged Packets. Range is 0..255. If the value specified is 0 then use the DTE Profile ID	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.43.2.9.1.12.1.14

This table specifies the DTE address of each
X25 neighbor that supports transparent bridging.
The bridge will forward to the neighbors defined in 
this table all broadcast packets and unknown 
unicast packets.

a3ComBrgX25NbrEntry row .1.3.6.1.4.1.43.2.9.1.13.1

Each entry contains the DTE address of an X25 neighbor.

Indexes

a3ComBrgX25NbrPort a3ComBrgX25NbrDTE

Column	Syntax	OID
a3ComBrgX25NbrPortmandatory The bridge port to which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.1.13.1.1
a3ComBrgX25NbrDTEmandatory The X121 address of the neighbor DTE.	X121Address Type Constraints: range: 0..17	.1.3.6.1.4.1.43.2.9.1.13.1.2
a3ComBrgX25NbrStatusmandatory This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.9.1.13.1.3

This table contains port specific source routing
information.

a3ComBrgSrPortEntry row .1.3.6.1.4.1.43.2.9.3.2.1

Each entry contains a set of information applied
to a specific bridge port.

Indexes

a3ComBrgSrPort

Column	Syntax	OID
a3ComBrgSrPortmandatory This identifies the bridge port to which the other objects in this entry apply.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.3.2.1.1
a3ComBrgSrPortSTEHopCountmandatory This object contains the maximum number of routing descriptors (ie, hop count) for Spanning Tree Explorer frames.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.3.2.1.2
a3ComBrgSrPortAREHopCountmandatory This object contains the maximum number of routing descriptors (ie, hop count) for All Routes Explorer frames.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.3.2.1.3
a3ComBrgSrPortHoldTimemandatory This parameter specifies the time interval, in minutes, that an inactive route entry can reside in the source routing table.	Integer32r/w Constraints: range: 1-1440	.1.3.6.1.4.1.43.2.9.3.2.1.4
a3ComBrgSrPortMinAccessPriormandatory This parameter determines the minimum access priority used for outoing frames on this port. End systems usually have a low access priority while bridges have a medium priority. This allows bridge, which typically handl…	Integer32r/w Constraints: range: 0-6	.1.3.6.1.4.1.43.2.9.3.2.1.5

A table containing mappings between Ring Number,
Bridge Number, and Wide Area Addresses.  This
information is learned from Explorer Frames sent
by end stations.

a3ComBrgSrWanAddrEntry row .1.3.6.1.4.1.43.2.9.3.3.1

Each entry contains a single Ring Number, Bridge
Number, Wide Area Address mapping.

Indexes

a3ComBrgSrWAportIndex a3ComBrgSrWAringNum a3ComBrgSrWAbrgNum

Column	Syntax	OID
a3ComBrgSrWAportIndexmandatory This identifies the bridge port that is connected to the ring identified by a3ComBrgSrWAringNum.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.3.3.1.1
a3ComBrgSrWAringNummandatory This identifies a specific wide area network. When a source route frame is bridged to this ring number, and to the bridge identified by a3ComBrgSrWAbrgNum, the Wide Area Address identified by the corresponding instance…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.3.3.1.2
a3ComBrgSrWAbrgNummandatory This identifies the bridge associated with the Wide Area Address identified by a3ComBrgSrWAddress.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.3.3.1.3
a3ComBrgSrWAddressmandatory This identifies the Wide Area Address associated with a specific ring number and bridge number. These are identified by the corresponding instances of a3ComBrgSrWAringNum and a3ComBrgSrWAbrgNum.	OctetString	.1.3.6.1.4.1.43.2.9.3.3.1.4

This table specifies whether end system source routing
is enabled on for each port on the system.  There are
separate controls for each protocol that may use source
routing.

a3ComBrgSrRDEntry row .1.3.6.1.4.1.43.2.9.3.6.1

Each entry applies to a specific port.

Indexes

a3ComBrgSrRDPort

Column	Syntax	OID
a3ComBrgSrRDPortmandatory This identifies the bridge port to which the other objects in this entry apply.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.9.3.6.1.1
a3ComBrgSrRDAppleTalkmandatory This specifies whether route discovery is initiated for AppleTalke end system packets. This discovery process occurs when a route to the end system does not exist in the local source routing table. If this is set to n…	Enumerationr/w Enumerated Values: 1 appleTalk 2 noAppleTalk	.1.3.6.1.4.1.43.2.9.3.6.1.2
a3ComBrgSrRDClnpmandatory This specifies whether route discovery is initiated for CLNP end system packets. This discovery process occurs when a route to the end system does not exist in the local source routing table. If this is set to noClnp,…	Enumerationr/w Enumerated Values: 1 clnp 2 noClnp	.1.3.6.1.4.1.43.2.9.3.6.1.3
a3ComBrgSrRDDecNetmandatory This specifies whether route discovery is initiated for DECNET end system packets. This discovery process occurs when a route to the end system does not exist in the local source routing table. If this is set to noDec…	Enumerationr/w Enumerated Values: 1 decNet 2 noDecNet	.1.3.6.1.4.1.43.2.9.3.6.1.4
a3ComBrgSrRDDlTestmandatory This specifies whether route discovery is initiated for DlTest end system packets. This discovery process occurs when a route to the end system does not exist in the local source routing table. If this is set to noDlT…	Enumerationr/w Enumerated Values: 1 dlTest 2 noDlTest	.1.3.6.1.4.1.43.2.9.3.6.1.5
a3ComBrgSrRDIpmandatory This specifies whether route discovery is initiated for IP end system packets. This discovery process occurs when a route to the end system does not exist in the local source routing table. If this is set to noIp, all…	Enumerationr/w Enumerated Values: 1 ip 2 noIp	.1.3.6.1.4.1.43.2.9.3.6.1.6
a3ComBrgSrRDIpxmandatory This specifies whether route discovery is initiated for IPX end system packets. This discovery process occurs when a route to the end system does not exist in the local source routing table. If this is set to noIpx, a…	Enumerationr/w Enumerated Values: 1 ipx 2 noIpx	.1.3.6.1.4.1.43.2.9.3.6.1.7
a3ComBrgSrRDLlc2mandatory This specifies whether route discovery is initiated for LLC2 end system packets. This discovery process occurs when a route to the end system does not exist in the local source routing table. If this is set to noLlc2,…	Enumerationr/w Enumerated Values: 1 llc2 2 noLlc2	.1.3.6.1.4.1.43.2.9.3.6.1.8
a3ComBrgSrRDVinesmandatory This specifies whether route discovery is initiated for Vines end system packets. This discovery process occurs when a route to the end system does not exist in the local source routing table. If this is set to noVine…	Enumerationr/w Enumerated Values: 1 vines 2 noVines	.1.3.6.1.4.1.43.2.9.3.6.1.9