zxAnXdsl2LConfMinSnrmDs
ZTE-AN-XDSL2-MIBII ·
.1.3.6.1.4.1.3902.1015.1001.1.3.15.1.6
Object
column
r/w
0.1 dB Unsigned32
The minimum Noise Margin the xTU-R receiver shall tolerate. If the noise margin falls below this level, the xTU-R shall request that the xTU-C increase the xTU-C transmit power. If an increase to xTU-C transmit power is not possible, a loss-of-margin (LOM) defect occurs, the xTU-R shall fail and attempt to reinitialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum.
Context
- MIB
- ZTE-AN-XDSL2-MIBII
- OID
.1.3.6.1.4.1.3902.1015.1001.1.3.15.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Units
- 0.1 dB
- Parent
- zxAnXdsl2SnrMarginConfPrfEntry
- Table
- zxAnXdsl2SnrMarginConfPrfTable
- Siblings
- 19
Syntax
0.1 dB Unsigned32
Values & Constraints
Object Constraints
range: 0-310
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxAnXdsl2SnrMarginConfPrfName This object identifies a row in this table. | column | OctetString | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.1 |
| zxAnXdsl2LConfRaUsTimeDs The Downstream Up-Shift Time Interval, to be used when
zxAnXdsl2LConfRaModeDs is set to dynamicRa. The interval of
time that the downstream noise margin should stay above the
Dow… | column | seconds Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.10 |
| zxAnXdsl2LConfRaUsTimeUs The Upstream Up-Shift Time Interval, to be used when
zxAnXdsl2LConfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay above the
Upstream Up-… | column | seconds Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.11 |
| zxAnXdsl2LConfRaDsNrmDs The Downstream Down-Shift Noise Margin value, to be used
when
zxAnXdsl2LConfRaModeDs is set to dynamicRa. If the downstream
noise margin is below this value and stays below tha… | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.12 |
| zxAnXdsl2LConfRaDsNrmUs The Upstream Downshift Noise Margin value, to be used when
zxAnXdsl2LConfRaModeUs is set to dynamicRa. If the upstream
noise margin is below this value and stays below that for m… | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.13 |
| zxAnXdsl2LConfRaDsTimeDs The Downstream Downshift Time Interval, to be used when
zxAnXdsl2LConfRaModeDs is set to dynamicRa. The interval of
time the downstream noise margin should stay below the
Downstr… | column | seconds Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.14 |
| zxAnXdsl2LConfRaDsTimeUs The Upstream Down-Shift Time Interval, to be used when
zxAnXdsl2LConfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay below the Upstream
D… | column | seconds Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.15 |
| zxAnXdsl2LConfSnrModeDs This parameter enables/disables the transmitter referred virtual
noise in the downstream direction. | column | VDSL2-LINE-TC-MIBXdsl2LineSnrMode | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.16 |
| zxAnXdsl2LConfSnrModeUs This parameter enables/disables the transmitter referred virtual
noise in the upstream direction. | column | VDSL2-LINE-TC-MIBXdsl2LineSnrMode | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.17 |
| zxAnXdsl2LConfRaModeDs The mode of operation of a rate-adaptive xTU-C in the transmit
direction. The parameter can take three values:
fixed (1),
raInit (2),
dynamicRa (3). | column | VDSL2-LINE-TC-MIBXdsl2RaMode | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.18 |
| zxAnXdsl2LConfRaModeUs The mode of operation of a rate-adaptive xTU-R in the transmit
direction. The parameter can take three values:
fixed (1),
raInit (2),
dynamicRa (3). | column | VDSL2-LINE-TC-MIBXdsl2RaMode | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.19 |
| zxAnXdsl2LConfTargetSnrmDs The minimum Noise Margin the xTU-R receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfull… | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.2 |
| zxAnXdsl2LConfTargetSnrmUs The minimum Noise Margin the xTU-C receiver shall achieve,
relative to the BER requirement for each of the upstream
bearer channels, to successfully … | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.3 |
| zxAnXdsl2SnrMarginConfRowStatus This object is used to create a new row or to modify or
delete an existing row in this table.
A profile is activated by setting this object to 'active'.
When 'activ… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.30 |
| zxAnXdsl2LConfMaxSnrmDs The maximum Noise Margin the xTU-R receiver shall try to
sustain. If the Noise Margin is above this level, the xTU-R
shall request that the xTU-C reduce the xTU-C transmit power
… | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.4 |
| zxAnXdsl2LConfMaxSnrmUs The maximum Noise Margin the xTU-C receiver shall try to
sustain. If the Noise Margin is above this level, the xTU-C
shall request that the xTU-R reduce the xTU-R transmit power
… | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.5 |
| zxAnXdsl2LConfMinSnrmUs The minimum Noise Margin the xTU-C receiver shall tolerate.
If the noise margin falls below this level, the xTU-C shall
request that the xTU-R increase the xTU-R transmit power.
I… | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.7 |
| zxAnXdsl2LConfRaUsNrmDs The Downstream Up-Shift Noise Margin value, to be used when
zxAnXdsl2LConfRaModeDs is set to dynamicRa. If the downstream
noise margin is above this value and stays above it for
… | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.8 |
| zxAnXdsl2LConfRaUsNrmUs The Upstream Up-Shift Noise Margin value, to be used when
zxAnXdsl2LConfRaModeUs is set to dynamicRa. If the upstream
noise margin is above this value and stays above it for more… | column | 0.1 dB Unsigned32 | .1.3.6.1.4.1.3902.1015.1001.1.3.15.1.9 |