dot1agCfmMepTransmitLbmResultOK

ZTE-AN-ETH-CFM-MIB · .1.3.6.1.4.1.3902.1015.60.1.3.1.1.53
MIB view Table view

Object

column SNMPv2-TCTruthValue 
Indicates the result of the operation:
              
- true       The Loopback Message(s) will be
             (or has been) sent.
- false      The Loopback Message(s) will not
             be sent.

Context

MIB
ZTE-AN-ETH-CFM-MIB
OID
.1.3.6.1.4.1.3902.1015.60.1.3.1.1.53
Type
column
Access
readonly
Status
current
Parent
dot1agCfmMepEntry
Table
dot1agCfmMepTable
Siblings
64

Syntax

SNMPv2-TCTruthValue
Source
SNMPv2-TCTruthValue
Base type
Enumeration

Values & Constraints

Type Values
1true
2false

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
dot1agCfmSessionId
Integer that is unique among all the MEPs in the same MA. Other definition is: a small integer, unique over a given Maintenance Association, identifying a specific Maintenance ass…
columnDot1agCfmSessionId.1.3.6.1.4.1.3902.1015.60.1.3.1.1.1
dot1agCfmMepLowPrDef
An integer value specifying the lowest priority defect that is allowed to generate fault alarm.
columnDot1agCfmLowestAlarmPri.1.3.6.1.4.1.3902.1015.60.1.3.1.1.10
dot1agCfmMepHighestPrDefect
The highest priority defect that has been present since the MEPs Fault Notification Generator State Machine was last in the FNG_RESET state.
columnDot1agCfmHighestDefectPri.1.3.6.1.4.1.3902.1015.60.1.3.1.1.11
dot1agCfmMepDefects
A vector of Boolean error conditions from Table 20-1, any of which may be true: DefRDICCM(0) DefMACstatus(1) DefRemoteCCM(2) DefErrorCCM(3) DefXconCCM(4)
columnDot1agCfmMepDefects.1.3.6.1.4.1.3902.1015.60.1.3.1.1.12
dot1agCfmMepCciSentCcms
Total number of Continuity Check messages transmitted.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.13
dot1agCfmMepId
Session Id
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.14
dot1agCfmMepMEPAttachType
MEP AttachType
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.15
dot1agCfmMepTunnelId
Tunnel Id
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.16
dot1agCfmMepLMFlage
LMFlage
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.17
dot1agCfmMepDMFlage
DMFlage
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.18
dot1agCfmMepPortName
Mep Port Name
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.3902.1015.60.1.3.1.1.19
dot1agCfmMepIfIndex
This object is the interface index of the interface either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, to which the MEP is attached. Upon a restart of th…
columnInterfaceIndexOrZero.1.3.6.1.4.1.3902.1015.60.1.3.1.1.2
dot1agCfmMepLbrIn
Total number of valid, in-order Loopback Replies received.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.20
dot1agCfmMepLbrInOutOfOrder
The total number of valid, out-of-order Loopback Replies received.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.21
dot1agCfmMepLbrBadMsdu
(optional) The total number of LBRs received whose mac_service_data_unit did not match (except for the OpCode) that of the corresponding LBM (20.2.3).
columnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.22
dot1agCfmMepLtmNextSeqNumber
Next transaction identifier/sequence number to be sent in a Linktrace message. This sequence number can be zero because it wraps around.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.23
dot1agCfmMepUnexpLtrIn
The total number of unexpected LTRs received (20.39.1).
columnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.24
dot1agCfmMepLbrOut
Total number of Loopback Replies transmitted.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.25
dot1agCfmMepRowStatus
The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.3902.1015.60.1.3.1.1.26
dot1agCfmMepCcCheckFlagcolumnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.27
dot1agCfmMepComplexFlagcolumnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.28
dot1agCfmMepclientLevelcolumnDot1agCfmClientLevel.1.3.6.1.4.1.3902.1015.60.1.3.1.1.29
dot1agCfmMepDirection
The direction in which the MEP faces on the Bridge port.
columnDot1agCfmMpDirection.1.3.6.1.4.1.3902.1015.60.1.3.1.1.3
dot1agCfmMepAISSendFlagcolumnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.30
dot1agCfmMepAISEnableFlagcolumnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.31
dot1agCfmMepLCKEnableFlagcolumnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.32
dot1agCfmMepTxFCfcolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.33
dot1agCfmMepRxFCbcolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.34
dot1agCfmMepTxFCbcolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.35
dot1agCfmMepRxFClcolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.36
dot1agCfmMepNearLostcolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.37
dot1agCfmMepFarLostcolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.38
dot1agCfmMepDalycolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.39
dot1agCfmMepPrimaryVid
An integer indicating the Primary VID of the MEP, always one of the VIDs assigned to the MEP's MA. The value 0 indicates that either the Primary VID is that of the MEP's MA, or th…
columnUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.4
dot1agCfmMepDalyAvecolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.40
dot1agCfmMepDalyChgcolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.41
dot1agCfmMepDalyChgAvecolumnSNMPv2-SMICounter32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.42
dot1agCfmMepTransmitLbmStatus
A Boolean flag set to true by the bridge port to indicate that another LBM may be transmitted. Reset to false by the MEP Loopback Initiator State Machine.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.43
dot1agCfmMepTransmitLbmDestMacAddress
The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column dot1agCfmMepTransmitLbmDestIsMepId is 'fals…
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.3902.1015.60.1.3.1.1.44
dot1agCfmMepTransmitLbmDestSessionId
The Maintenance association End Point SessionId of another MEP in the same Maintenance Association to which the LBM is to be sent. This address will be used if the value of the co…
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.45
dot1agCfmMepTransmitLbmDestIsSessionId
True indicates that SessionId of the target MEP is used for Loopback transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback tran…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.46
dot1agCfmMepTransmitLbmDestMepId
The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the LBM is to be sent. This address will be used if the value of the c…
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.47
dot1agCfmMepTransmitLbmDestIsMepId
True indicates that MEPID of the target MEP is used for Loopback transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmis…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.48
dot1agCfmMepTransmitLbmMessages
The number of Loopback messages to be transmitted.
columnInteger32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.49
dot1agCfmMepActive
Administrative state of the MEP A Boolean indicating the administrative state of the MEP. True indicates that the MEP is to function normally, and false that it is to cease functi…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.5
dot1agCfmMepTransmitLbmDataTlv
An arbitrary amount of data to be included in the Data TLV, if the Data TLV is selected to be sent.
columnOctetString.1.3.6.1.4.1.3902.1015.60.1.3.1.1.50
dot1agCfmMepTransmitLbmVlanPriority
Priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame. The default value is CCM priority.
columnInteger32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.51
dot1agCfmMepTransmitLbmVlanDropEnable
Drop Enable bit value to be used in the VLAN tag, if present in the transmitted frame. For more information about VLAN Drop Enable, please check IEEE 802.1ad.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.52
dot1agCfmMepTransmitLbmSeqNumber
The Loopback Transaction Identifier (dot1agCfmMepNextLbmTransId) of the first LBM (to be) sent. The value returned is undefined if dot1agCfmMepTransmitLbmResultOK is false.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.54
dot1agCfmMepTransmitLtmStatus
A Boolean flag set to true by the bridge port to indicate that another LTM may be transmitted. Reset to false by the MEP Linktrace Initiator State Machine.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.55
dot1agCfmMepTransmitLtmFlags
The flags field for LTMs transmitted by the MEP.
columnBits.1.3.6.1.4.1.3902.1015.60.1.3.1.1.56
dot1agCfmMepTransmitLtmTargetMacAddress
The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column dot1agCfmMepTransmitLtmTargetIsMepId is 'fa…
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.3902.1015.60.1.3.1.1.57
dot1agCfmMepTransmitLtmTargetSessionId
An indication of the Target MAC Address Field to be transmitted: The Maintenance association End Point SessionId of another MEP in the same Maintenance Association This address wi…
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.58
dot1agCfmMepTransmitLtmTargetIsSessionId
True indicates that SessionId of the target MEP is used for Linktrace transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback tra…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.59
dot1agCfmMepFngState
Current state of the MEP Fault Notification Generator State Machine.
columnDot1agCfmFngState.1.3.6.1.4.1.3902.1015.60.1.3.1.1.6
dot1agCfmMepTransmitLtmTargetMepId
An indication of the Target MAC Address Field to be transmitted: The Maintenance association End Point Identifier of another MEP in the same Maintenance Association This address w…
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.60
dot1agCfmMepTransmitLtmTargetIsMepId
True indicates that MEPID of the target MEP is used for Linktrace transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmi…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.61
dot1agCfmMepTransmitLtmTtl
The LTM TTL field. Default value, if not specified, is 64. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 by each Linktrace Responder that hand…
columnUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.62
dot1agCfmMepTransmitLtmResult
Indicates the result of the operation: - true The Linktrace Message will be (or has been) sent. - false The Linktrace Message will not be sent
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.63
dot1agCfmMepTransmitLtmSeqNumber
The LTM Transaction Identifier (dot1agCfmMepLtmNextSeqNumber) of the LTM sent. The value returned is undefined if dot1agCfmMepTransmitLtmResult is false.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.64
dot1agCfmMepTransmitLtmEgressIdentifier
Identifies the MEP Linktrace Initiator that is originating, or the Linktrace Responder that is forwarding, this LTM. The low-order six octets contain a 48-bit IEEE MAC address uni…
columnOctetString.1.3.6.1.4.1.3902.1015.60.1.3.1.1.65
dot1agCfmMepCciEnabled
If set to true, the MEP will generate CCM messages.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3902.1015.60.1.3.1.1.7
dot1agCfmMepCcmLtmPriority
The priority value for CCMs and LTMs transmitted by the MEP. Default Value in the highest priority value allowed to pass through the bridge port for any of this MEPs VIDs. The man…
columnUnsigned32.1.3.6.1.4.1.3902.1015.60.1.3.1.1.8
dot1agCfmMepMacAddress
MAC address of the MEP.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.3902.1015.60.1.3.1.1.9