wlsxIfState

WLSX-TRAP-MIB · .1.3.6.1.4.1.14823.2.3.1.11.1.1.128
MIB view Table view

Object

scalar ARUBA-TCArubaIfState 
This object specifies the state of an interface.

Context

MIB
WLSX-TRAP-MIB
OID
.1.3.6.1.4.1.14823.2.3.1.11.1.1.128
Type
scalar
Access
notifyonly
Status
current
Parent
wlsxTrapObjectsGroup
Siblings
166

Syntax

ARUBA-TCArubaIfState
Source
ARUBA-TCArubaIfState
Base type
Enumeration

Values & Constraints

Type Values
1linkUp
2linkDown

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
wlsxTrapAPMacAddress
This object is used in the traps to indicate the wired MAC address of an access point, for which the trap is being raised.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.1
wlsxReceiverMac
This object is used in the traps to indicate the MAC address of the receiver.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.10
wlsxTrapAPPrevMode
This Object represents the APs Previous Mode.
scalarARUBA-TCArubaAccessPointMode.1.3.6.1.4.1.14823.2.3.1.11.1.1.100
wlsxTrapAPARMChangeReason
This Object represents the APs Previous Mode.
scalarARUBA-TCArubaARMChangeReason.1.3.6.1.4.1.14823.2.3.1.11.1.1.101
wlsxTrapAPChannelSec
This object is used in the traps to indicate the Current Secondary Channel.
scalarARUBA-TCArubaHTExtChannel.1.3.6.1.4.1.14823.2.3.1.11.1.1.102
wlsxTrapUserAttributeChangeType
This object represents type of the configuration change.
scalarARUBA-TCArubaConfigurationChangeType.1.3.6.1.4.1.14823.2.3.1.11.1.1.103
wlsxTrapApControllerIp
IP address of the controller to which the AP is (or was most recently) registered.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.104
wlsxTrapApMasterStatus obsolete
Status of the AP as seen by the master when the status changes. **NOTE: this object is obsoleted and replaced by wlsxTrapApConductorStatus
scalarARUBA-TCArubaAPMasterStatus.1.3.6.1.4.1.14823.2.3.1.11.1.1.105
wlsxTrapCaName
This object is used in the traps to indicate the name of the trustpoint.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.106
wlsxTrapCrlName
This object is used in the traps to indicate the name of the crl.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.107
wlsxTrapCount
This object represents the number of occurrence of this trap.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.108
wlsxTrapPowerSupplyNumber
This object represents the power supply number.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.109
wlsxTrapTransmitterMac
This object is used in the traps to indicate the MAC address of the transmitter.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.11
wlsxTrapFanTrayNumber
This object represents the Fan Tray number.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.110
wlsxTrapClientClassification
This object is used in the traps to indicate the classification of the client.
scalarARUBA-TCArubaStationType.1.3.6.1.4.1.14823.2.3.1.11.1.1.111
wlsxThresholdResourceType
This object represents the Threshold alert's Resource Type .
scalarARUBA-TCArubaThresholdResourceType.1.3.6.1.4.1.14823.2.3.1.11.1.1.112
wlsxThresholdResourceName
This object represents the Threshold alert's Resource Name .
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.113
wlsxThresholdValue
This object represents the Threshold alert's set threshold value.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.114
wlsxResourceValue
This object represents the Threshold alert's actual value.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.115
wlsxStackPrevSlot
This object specifies the slot number of this stack element prior to topology change in stack. A value of -1 indicates that this slot was not in Active state of stack prior to top…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.116
wlsxStackCurrentSlot
This object specifies the slot number of this stack element after the topology change in stack. A value of -1 indicates that this slot is not in Active state of stack after the to…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.117
wlsxStackPrevState
This object specifies the state of this stack element prior to topology change in stack.
scalarARUBA-TCArubaStackState.1.3.6.1.4.1.14823.2.3.1.11.1.1.118
wlsxStackCurrentState
This object specifies the state of this stack element after topology change in stack.
scalarARUBA-TCArubaStackState.1.3.6.1.4.1.14823.2.3.1.11.1.1.119
wlsxTrapReceiverMac
This object is used in the traps to indicate the MAC address of the receiver.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.12
wlsxStackChangeEvent
This object specifies the event which caused change in topology in stack.
scalarARUBA-TCArubaStackChangeEvent.1.3.6.1.4.1.14823.2.3.1.11.1.1.120
wlsxStackProtoIfTopoJoined
This object specifies whether an interface has joined the stacking topology or left the topology.
scalarARUBA-TCArubaStackIfTopoJoined.1.3.6.1.4.1.14823.2.3.1.11.1.1.121
wlsxStackMemberMacAddress
This object specifies mac-address of this stack element.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.122
wlsxStackMemberSlotNumber
This object specifies the slot number of this element in stack.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.123
wlsxStackIfName
This object specifies the interface name which is part of stacking link connected to other stacking element.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.124
wlsxTrapLicenseServerDaysRemaining
This object represents number of the days remaining prior to expiry of license limits sent by the server.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.125
wlsxTrapLicenseClientDaysRemaining
This object represents number of the days remaining prior to expiry of licenses contributed by a license client.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.126
wlsxIfIndex
This object specifies the ifIndex.
scalarARUBA-TCInterfaceIndex.1.3.6.1.4.1.14823.2.3.1.11.1.1.127
wlsxIfStateChangeReason
This object specifies the reason for interface state change.
scalarARUBA-TCArubaIfStateChangeReason.1.3.6.1.4.1.14823.2.3.1.11.1.1.129
wlsxTrapSnr
This object is used in the traps to indicate the Signal to Noise ratio.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.13
wlsxTrapAPPreviousUplinkType
This object specifies the up link type for an AP.
scalarARUBA-TCArubaAPUplinkType.1.3.6.1.4.1.14823.2.3.1.11.1.1.130
wlsxTrapAPPreviousUplinkActiveTime
This object specifies the up link type for an AP.
scalarSNMPv2-SMITimeTicks.1.3.6.1.4.1.14823.2.3.1.11.1.1.131
wlsxTrapAPActiveUplinkType
This object specifies the up link type for an AP.
scalarARUBA-TCArubaAPUplinkType.1.3.6.1.4.1.14823.2.3.1.11.1.1.132
wlsxTrapAPUplinkChangeReason
This object specifies the up link change reason.
scalarARUBA-TCArubaAPUplinkChangeReason.1.3.6.1.4.1.14823.2.3.1.11.1.1.133
wlsxTrapExpiringCertName
This object is used in the traps to indicate the name of the certificate that is expiring in less than 60 days.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.134
wlsxTrapExpiredCertName
This object is used in the traps to indicate the name of the certificate that has expired.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.135
wlsxTrapHTMode
This object represents HT Mode.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.136
wlsxTrapPhyType
This object represents Physical Type.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.137
wlsxTrapAPManagedModeConfigFailure
This object indicates the error for the failure of config apply on IAP.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.138
wlsxTrapAuthServerAddress
This object is used in the traps to indicate the Authentication Server IP used for Authentication.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.139
wlsxTrapSignatureName
This object is used in the traps to indicate the Signature Name.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.14
wlsxTrapPortalServerName
This object is used in the traps to indicate the Captive Portal Server used for Authentication.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.140
wlsxTrapPortalServerAddress
This object is used in the traps to indicate the Captive Portal Server IP or host name used for Authentication.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.141
wlsxTrapPortalServerDownReason
This object specifies the captive portal server down reason.
scalarARUBA-TCArubaPortalServerDownReason.1.3.6.1.4.1.14823.2.3.1.11.1.1.142
wlsxTrapLicensePlatformMismatchKey
This object represents license incompatibility with the given platform.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.143
wlsxTrapTargetAPName
This object is used in the traps to indicate the target's AP name.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.144
wlsxTrapTargetAPMac
This object is used in the traps to indicate the target's MAC address.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.145
wlsxTrapAPUSBStatus
This object represents plug in or plug out status of an USB device.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.146
wlsxTrapUSBVendorProductID
This object represents vendor ID or product ID of an USB device.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.147
wlsxTrapSwitchIpv6
This object represents the controller IPv6 address.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.148
wlsxTrapStationBlackListReasonStr obsolete
The Reason for which a station is black listed in details. **NOTE: this trap is obsoleted and replaced by wlsxTrapStationDenyListReasonStr
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.149
wlsxTrapFrameType
This object is used in the traps to indicate the Frame Type
scalarARUBA-TCArubaFrameType.1.3.6.1.4.1.14823.2.3.1.11.1.1.15
wlsxTrapPeerIpAddress
This object is used in the traps to indicate the peer IP address of Cluster VLAN probe.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.150
wlsxTrapConnectionStatus
This object is used in the traps to indicate the Connection status of Cluster VLAN probe.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.151
wlsxTrapFailedVlan
This object is used in the traps to indicate the failed VLAN id of cluster VLAN probe.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.152
wlsxTrapMatchedIpv6
This object is used in the traps to indicate the IPv6 address
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.153
wlsxTrapDeviceIpv6Address
This object represents the IPv6 address of a device seen by an AP.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.154
wlsxTrapAuthFailureReason
This object represents the reason for the authentication failure.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.155
wlsxTrapAPPhyType
This object represents Band Information.
scalarARUBA-TCArubaPhyType.1.3.6.1.4.1.14823.2.3.1.11.1.1.156
wlsxTrapAPSecChannel
This object represents Secondary Channel.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.157
wlsxTrapAPHTMode
This object represents HT-Mode Information.
scalarARUBA-TCArubaHTMode.1.3.6.1.4.1.14823.2.3.1.11.1.1.158
wlsxTrapAPBand
This object represents the radio band on which an AP operates on.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.159
wlsxTrapAddressType
This object is used in the traps to indicate the Address type.
scalarARUBA-TCArubaAddressType.1.3.6.1.4.1.14823.2.3.1.11.1.1.16
wlsxTrapTargetAPBand
This object represents the radio band on which the target AP operates on.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.160
wlsxTrapStationDenyListReason
The Reason for which a station is added to denylist.
scalarARUBA-TCArubaDenyListReason.1.3.6.1.4.1.14823.2.3.1.11.1.1.161
wlsxTrapStationDenyListReasonStr
The Reason for which a station is added to denylist in details.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.162
wlsxTrapApConductorStatus
Status of the AP as seen by the conductor when the status changes.
scalarARUBA-TCArubaAPConductorStatus.1.3.6.1.4.1.14823.2.3.1.11.1.1.163
wlsxTrapAPPrevPhyType
This object represents Prev Band Information.
scalarARUBA-TCArubaPhyType.1.3.6.1.4.1.14823.2.3.1.11.1.1.164
wlsxTrapAPPrevHTMode
This object represents Previous HT-Mode Information.
scalarARUBA-TCArubaHTMode.1.3.6.1.4.1.14823.2.3.1.11.1.1.165
wlsxLicenseType
This object is used in the traps to indicate the License Type.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.166
wlsxLicensePoolName
This object is used in the traps to indicate the pool name for a License.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.167
wlsxTrapAPLocation
This object is used in the traps to indicate the Location of the AP.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.17
wlsxTrapAPChannel
This object is used in the traps to indicate the Current Channel.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.18
wlsxTrapAPTxPower
This object is used in the traps to indicate the AP Transmit Power.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.19
wlsxTrapAPIpAddress
This object is used in the traps to indicate the IP address of an access point, for which the trap is being raised.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.2
wlsxTrapMatchedMac
This object is used in the traps to indicate the MAC address
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.20
wlsxTrapMatchedIp
This object is used in the traps to indicate the IP address
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.21
wlsxTrapRogueIfoURL
This object is used to point to the WEBUI Rogue AP information URL.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.22
wlsxTrapVlanId
This object is used in the traps to indicate the VLAN Id.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.23
wlsxTrapAdminStatus
This object is used in the traps to indicate the admin status of VLAN.
scalarARUBA-TCArubaEnableValue.1.3.6.1.4.1.14823.2.3.1.11.1.1.24
wlsxTrapOperStatus
This object is used in the traps to indicate the admin status of VLAN.
scalarARUBA-TCArubaOperStateValue.1.3.6.1.4.1.14823.2.3.1.11.1.1.25
wlsxTrapAuthServerName
This object is used in the traps to indicate the Authentication Server used for Authentication.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.26
wlsxTrapAuthServerTimeout
This object is used in the traps to indicate the Authentication Server Timeout.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.27
wlsxTrapCardSlot
This object is used in the traps to indicate the Slot in which this card is present.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.28
wlsxTrapTemperatureValue
This object is used in the traps to indicate the Temperature Value.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.29
wlsxTrapAPBSSID
This object is used in the traps to indicate the BSSID of the access point, for which the trap is being raised.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.3
wlsxTrapProcessName
This object is used in the traps to indicate the Process name.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.30
wlsxTrapFanNumber
This object is used in the traps to indicate the Fan Number.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.31
wlsxTrapVoltageType
This object is used in the traps to indicate the type of Voltage.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.32
wlsxTrapVoltageValue
This object is used in the traps to indicate the voltage value in Float.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.33
wlsxTrapStationBlackListReason obsolete
The Reason for which a station is black listed. **NOTE: this trap is obsoleted and replaced by wlsxTrapStationDenyListReason
scalarARUBA-TCArubaBlackListReason.1.3.6.1.4.1.14823.2.3.1.11.1.1.34
wlsxTrapSpoofedIpAddress
This object is used in a trap to identify a spoofed IP address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.35
wlsxTrapSpoofedOldPhyAddress
This object is used in a trap to identify an old MAC address.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.36
wlsxTrapSpoofedNewPhyAddress
This object is used in a trap to identify a New MAC address.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.37
wlsxTrapDBName
This object is used in a trap to identify name of the database.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.38
wlsxTrapDBUserName
This object is used in a trap to identify name of the database user.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.39
wlsxTrapEssid
This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.4
wlsxTrapDBIpAddress
This object is used in a trap to identify the IpAddress of the Database.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.40
wlsxTrapDBType
This object is used in a trap to identify the port of the user.
scalarARUBA-TCArubaDBType.1.3.6.1.4.1.14823.2.3.1.11.1.1.41
wlsxTrapVrrpID
This object contains the Virtual Router Identifier.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.42
wlsxTrapVrrpMasterIp
This object contains the Master IP address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.43
wlsxTrapVrrpOperState
This object represents the VRRP Operational state.
scalarARUBA-TCArubaVrrpState.1.3.6.1.4.1.14823.2.3.1.11.1.1.44
wlsxTrapESIServerGrpName
This object represents the External Services Interface (ESI) Server Group name
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.45
wlsxTrapESIServerName
This object represents the External Services Interface (ESI) Server Name
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.46
wlsxTrapESIServerIpAddress
This object represents the External Services Interface (ESI) Server IP address
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.47
wlsxTrapLicenseDaysRemaining
This object represents number of the days remaining prior to a license expiry.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.48
wlsxTrapSwitchIp
This object represents the controller IP address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.49
wlsxTrapTargetAPBSSID
This object is used in the traps to indicate the BSSID of the access point, for which we are raising the trap. If an Air Monitor is sending the trap then this will indicate AP. If…
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.5
wlsxTrapSwitchRole
This object represents the Role of the controller.
scalarARUBA-TCArubaSwitchRole.1.3.6.1.4.1.14823.2.3.1.11.1.1.50
wlsxTrapUserIpAddress
This object represents IP address of the User.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.51
wlsxTrapUserPhyAddress
This object represents MAC address of the User.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.52
wlsxTrapUserName
This object represents the user name.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.53
wlsxTrapUserRole
This object represents the Authentication method of the user.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.54
wlsxTrapUserAuthenticationMethod
This object represents the Authentication method of the user.
scalarARUBA-TCArubaAuthenticationMethods.1.3.6.1.4.1.14823.2.3.1.11.1.1.55
wlsxTrapAPRadioNumber
This object represents the radio number.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.56
wlsxTrapRogueInfoURL
This object is used to point to the WEBGUI Rogue AP information URL.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.57
wlsxTrapInterferingAPInfoURL
This object is used to point to the WEBGUI Rogue interfering AP information URL.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.58
wlsxTrapPortNumber
This object is used in the traps to indicate the port number.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.59
wlsxTrapTargetAPSSID
This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised. If an Air Monitor is sending the trap then this will indicate AP. If…
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.6
wlsxTrapTime
This object is used in all the enterprise traps to indicate the the time when the trap is generated on the controller.
scalarSNMPv2-TCDateAndTime.1.3.6.1.4.1.14823.2.3.1.11.1.1.60
wlsxTrapHostIp
This object represents the Trap host.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.61
wlsxTrapHostPort
This object represents the Trap host port.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.62
wlsxTrapConfigurationId
This object represents the ID of the configuration, to be used in traps.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.63
wlsxTrapCTSURL
This object represents the URL from which the transfer should happen.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.64
wlsxTrapCTSTransferType
This object represents the transfer type, upload or download.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.65
wlsxTrapConfigurationState
This object represents state of the configuration transfer.
scalarARUBA-TCArubaConfigurationState.1.3.6.1.4.1.14823.2.3.1.11.1.1.66
wlsxTrapUpdateFailureReason
This object represents the reason for the update failure.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.67
wlsxTrapUpdateFailedObj
This variable represents the AMAPI object which is the reason for the the update failure.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.68
wlsxTrapTableEntryChangeType
This object represents type of the configuration change.
scalarARUBA-TCArubaConfigurationChangeType.1.3.6.1.4.1.14823.2.3.1.11.1.1.69
wlsxTrapTargetAPChannel
This object is used in the traps to indicate the channel of the access point, for which the trap is being raised. If an air monitor is sending the trap then this will indicate AP.…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.7
wlsxTrapGlobalConfigObj
This variable represents the AMAPI object corresponding to the global configuration change.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.70
wlsxTrapTableGenNumber
This object represents generation number of a table. Used in the MMS, to keep track of the table content changes.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.71
wlsxTrapLicenseId
This object is used in the traps to indicate the license ID.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.72
wlsxTrapConfidenceLevel
This object is used in the traps to indicate the Confidence Level as a percentage
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.73
wlsxTrapMissingLicenses
This variable indicates any licenses that are not present during a configuration update
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.74
wlsxVoiceCurrentNumCdr
This object represents the number of CDRs in buffer.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.75
wlsxTrapTunnelId
This Object represents the tunnel ID.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.76
wlsxTrapTunnelStatus
This Object represents the tunnel Status.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.77
wlsxTrapTunnelUpReason
This Object represents the tunnel up reason.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.78
wlsxTrapTunnelDownReason
This Object represents the tunnel down reason.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.79
wlsxTrapNodeMac
This object is used in the traps to indicate the MAC address of a node.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.8
wlsxTrapApSerialNumber
This object represents the AP Serial Number.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.80
wlsxTrapTimeStr
This object represents the Time in String format.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.81
wlsxTrapMasterIp obsolete
This object represents the master IP address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.82
wlsxTrapLocalIp obsolete
This object represents the Local IP address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.83
wlsxTrapMasterName obsolete
This object represents the master controller name.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.84
wlsxTrapLocalName obsolete
This object represents the local controller name.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.85
wlsxTrapPrimaryControllerIp
This object represents the IP address of the AP's primary controller.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.86
wlsxTrapBackupControllerIp
This object represents the IP address of the AP's backup controller.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.87
wlsxTrapSpoofedFrameType
This object is used in the traps to indicate the Spoofed Frame Type
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.88
wlsxTrapAssociationType
This object is used in the traps to indicate the type of association
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.89
wlsxTrapSourceMac
This object is used in the traps to indicate the MAC address of the source.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.9
wlsxTrapDeviceIpAddress
This object represents the IP address of a device seen by an AP.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.90
wlsxTrapDeviceMac
This object represents the MAC address of a device seen by an AP.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.91
wlsxTrapVcIpAddress
This object represents the Ip Address of a Voice client.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.92
wlsxTrapVcMacAddress
This object represents the MAC address of a Voice client.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.14823.2.3.1.11.1.1.93
wlsxTrapAPName
This object is used in the traps to indicate the Name of the AP.
scalarOctetString.1.3.6.1.4.1.14823.2.3.1.11.1.1.94
wlsxTrapApMode
This Object represents the AP Mode.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.95
wlsxTrapAPPrevChannel
This object is used in the traps to indicate the Previous Channel.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.96
wlsxTrapAPPrevChannelSec
This object is used in the traps to indicate the Previous Secondary Channel.
scalarARUBA-TCArubaHTExtChannel.1.3.6.1.4.1.14823.2.3.1.11.1.1.97
wlsxTrapAPPrevTxPower
This object is used in the traps to indicate previous AP Transmit Power.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.14823.2.3.1.11.1.1.98
wlsxTrapAPCurMode
This Object represents the APs Current Mode.
scalarARUBA-TCArubaAccessPointMode.1.3.6.1.4.1.14823.2.3.1.11.1.1.99