nearFieldRange
WHISP-BOX-MIBV2-MIB ·
.1.3.6.1.4.1.161.19.3.3.2.262
Object
scalar
r/w
feet Integer32
Range in feet for near field operation. This is applied only when nearFieldOperation is set to enable(1) and eirp is 22dBm or below or when Engineering keyed. The maximum range of 3000ft applies negligible correction. PMP 450m only.
Context
- MIB
- WHISP-BOX-MIBV2-MIB
- OID
.1.3.6.1.4.1.161.19.3.3.2.262- Type
- scalar
- Access
- readwrite
- Status
- current
- Units
- feet
- Parent
- whispBoxConfig
- Siblings
- 248
Syntax
feet Integer32
Values & Constraints
Object Constraints
range: 6-3000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| linkNegoSpeed obsolete Link negotiation speeds.
H10BT -- 10 Base T Half Duplex,
F10BT -- 10 Base T Full Duplex,
H100BT -- 100 Base T Half Duplex,
F100BT -- 100 Base T Full Duplex.
Separate the values wi… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.1 |
| bhTimingMode Variable to switch between Timing Master and Timing Slave.
For Backhaul units only. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.10 |
| mac3VIDMapAddr MAC Address for Entry 3 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.100 |
| mac3VIDMapVid VID for Entry 3 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.101 |
| mac4VIDMapAddr MAC Address for Entry 4 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.102 |
| mac4VIDMapVid VID for Entry 4 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.103 |
| mac5VIDMapAddr MAC Address for Entry 5 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.104 |
| mac5VIDMapVid VID for Entry 5 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.105 |
| mac6VIDMapAddr MAC Address for Entry 6 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.106 |
| mac6VIDMapVid VID for Entry 6 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.107 |
| mac7VIDMapAddr MAC Address for Entry 7 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.108 |
| mac7VIDMapVid VID for Entry 7 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.109 |
| bhModulation obsolete Modulation scheme. For Backhaul units only. Only level 4
backhaul can be changed to 20Mbits/Second. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.11 |
| mac8VIDMapAddr MAC Address for Entry 8 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.110 |
| mac8VIDMapVid VID for Entry 8 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.111 |
| mac9VIDMapAddr MAC Address for Entry 9 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.112 |
| mac9VIDMapVid VID for Entry 9 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.113 |
| mac10VIDMapAddr MAC Address for Entry 10 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.114 |
| mac10VIDMapVid VID for Entry 10 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.115 |
| vlanPortType VLAN Port Type for VLAN interface. Default is Q. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.116 |
| vlanAcceptQinQFrames Allow/Disallow packets already doubly-tagged (QinQ) to ingress the FEC of BHM, BHS, or MP SM. Not configurable on MP AP. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.117 |
| whispWebUserAccessMode This variable selects if web page users for the radio should be authenticated locally or
via a centralised remote Radius server | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.118 |
| usrAccountEnableAccounting Select the level of accounting information to be reported to the server | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.119 |
| powerControl Power control.
FSK Only. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.12 |
| allowRejectThenLocal Control for allowing local authenication if the AAA remote server | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.120 |
| snrCalculation deprecated This OID is deprecated. Receive quality calulation is always on since it no longer affects packet per second performance. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.121 |
| priorityPrecedence Allows user to decide if 802.1p or DiffServ priority bits should be used first when making priority decisions. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.122 |
| installationColorCode Installation Color Code. Allows non-configured SMs to register to an AP with UCC enabled
in order to facilitate remote provisioning. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.123 |
| apSmMode Set AP to SM or SM to AP. Useful for facillitating scripting of running Spectrum Analyzer on an AP.
Radio must have AP Feature Key. 1 - Set to SM, 0 - Set to AP. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.124 |
| pppoeFilter To set PPPoE packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.125 |
| smbFilter To set SMB packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.126 |
| snmpFilter To set SNMP packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.127 |
| userP1Filter To set user defined port 1 packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.128 |
| userP2Filter To set user defined port 2 packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.129 |
| extFilterDelay obsolete Obsoleted. External Filters Delay. For 900MHz FSK radios only. | scalar | nanoseconds Integer32 | .1.3.6.1.4.1.161.19.3.3.2.13 |
| userP3Filter To set user defined port 3 packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.130 |
| allOtherIpFilter To set all other IPv4 packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.131 |
| allIpv4Filter To set all IPv4 packet filter. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp,
IPv4 Mcast, User Defined Ports, and All Other IPv4). | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.132 |
| arpFilter To set ARP packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.133 |
| allOthersFilter To set all other packet filter when. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.134 |
| userDefinedPort1 An integer value of number one user defined port. Range:0-65535 | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.135 |
| port1TCPFilter To set user defined port 1 TCP traffic filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.136 |
| port1UDPFilter To set user defined port 1 UDP traffic filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.137 |
| userDefinedPort2 An integer value of number two user defined port. Range:0-65535 | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.138 |
| port2TCPFilter To set user defined port 2 TCP traffic filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.139 |
| antennaGain External Antenna Gain. For radios that uses an external antenna or the DFS feature.
Not applicable to PMP 450m. | scalar | dBi Integer32 | .1.3.6.1.4.1.161.19.3.3.2.14 |
| port2UDPFilter To set user defined port 2 UDP traffic filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.140 |
| userDefinedPort3 An integer value of number three user defined port. Range:0-65535 | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.141 |
| port3TCPFilter To set user defined port 3 TCP traffic filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.142 |
| port3UDPFilter To set user defined port 3 UDP traffic filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.143 |
| bootpcFilter To set bootp client sourced packets filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.144 |
| bootpsFilter To set bootp server sourced packets filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.145 |
| ip4MultFilter To set IPv4 MultiCast packets filter when
NAT is disabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.146 |
| packetFilterDirection To set packet filter direction. Upstream is default. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.147 |
| encryptionConfig For supported radio, set the encryption algorithm to use.
DES by default. Cannot be set if encryption is disabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.148 |
| pppoeCtlPriority Prioritization of PPPoE Control packets. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.149 |
| eirp Transmit EIRP of radio.
PMP 450m only. | scalar | dBm Integer32 | .1.3.6.1.4.1.161.19.3.3.2.15 |
| ftpPort Port used to for FTP. Default is 21. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.150 |
| httpPort Port used to for HTTP. Default is 80. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.151 |
| httpsPort Port used to for HTTPs. Default is 443. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.152 |
| snmpPort Port used to for SNMP. Default is 161. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.153 |
| snmpTrapPort Port used to for SNMP Traps. Default is 162. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.154 |
| webAccess This variable determines if only HTTP or HTTPs connection are allowed.
0: HTTP Only
1: HTTPs Only
2: HTTP and HTTPs Both | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.155 |
| syslogDomainNameAppend Select whether to append the configured management domain name to
the Syslog server name. For example, if dnsMgmtDomainName is
set to 'example.com', syslogServerAddr is set to 's… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.156 |
| syslogServerAddr Syslog server address either in dotted decimal notation or a Fully Qualified Domain Name | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.157 |
| syslogServerPort Listening port on the Syslog server. Default is 514. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.158 |
| syslogMinLevel Sets the minimum syslog severity to transmit. Messages with a lower severity value (i.e. numerically higher) than this will not be transmitted. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.159 |
| dynamicLearning To enable VLAN dynamic learning. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.16 |
| allIpv6Filter To set all IPv6 packet filter. Enabling this will automatically enable all of the known IPv6 filters (SMB, SNMP, Bootp,
IPv6 Mcast, User Defined Ports, and All Other IPv6). | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.160 |
| ipv6smbFilter To set IPv6 SMB packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.161 |
| ipv6snmpFilter To set IPv6 SNMP packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.162 |
| ipv6bootpcFilter To set IPv6 bootp client sourced packets filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.163 |
| ipv6bootpsFilter To set IPv6 bootp server sourced packets filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.164 |
| ipv6MultFilter To set IPv6 MultiCast packets filter when
NAT is disabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.165 |
| allOtherIpv6Filter To set all other IPv6 packet filter. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.166 |
| snmpStatus This variable determines SNMP operation mode.
1: Enable SNMPv2c only
2: Enable SNMPv3 only
3: Enable SNMPv2c and SNMPv3 | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.167 |
| telnetStatus This variable determines if Telnet to enabled or not.
0: Disable Telnet
1: Enable Telnet | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.168 |
| ftpStatus This variable determines if FTP to enabled or not.
0: Disable FTP
1: Enable FTP | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.169 |
| managementVID Management VLAN VID. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.17 |
| tftpStatus This variable determines if TFTP is enabled or not.
0: Disable TFTP
1: Enable TFTP | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.170 |
| userMode User Mode 1=Read-Only 0=Read-Write(default). | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.171 |
| tcpAckPriority Prioritize TCP ACK that are 64 bytes or less. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.172 |
| codePointSelect Codepoint Select.This represents the CodePoint Selection to be modified via Priority Select | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.173 |
| prioritySelect Priority Select.The priority setting input for the CodePoint selected in CodePoint Select. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.174 |
| auxPortEnable Enable(1) or Disable(0) aux ethernet port on 450i radio | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.175 |
| poeAuxEnable Enable(1) or Disable(0) aux ethernet port PoE on 450i radio | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.176 |
| whispUsrAuth Select method for User Authentication. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.177 |
| agingTimeout Aging timeout. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.18 |
| frameType Allow only tagged frame. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.19 |
| colorCode Color code. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.2 |
| addVlanMember Write-Only OID,Add VLAN number which needs to be added. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.20 |
| lan1DhcpRelease Setting the variable to '1' will release LAN1's IP address
and send a DHCP Release Message to the DHCP server.
Applicable only when NAT is disabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.201 |
| lan1DhcpRenew Setting the variable to '1' will renew LAN1's lease time
for its current IP address.
Applicable only when NAT is disabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.202 |
| lan3DhcpRelease Setting the variable to '1' will release LAN3's (RF Public) IP address
and send a DHCP Release Message to the DHCP server.
Applicable only when NAT is enabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.203 |
| lan3DhcpRenew Setting the variable to '1' will renew LAN3's (RF Public)
lease time for its current IP address.
Applicable only when NAT is enabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.204 |
| natDhcpRelease Setting the variable to '1' will release WAN's (NAT Public) IP address
and send a DHCP Release Message to the DHCP server.
Applicable only when NAT is enabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.205 |
| natDhcpRenew Setting the variable to '1' will renew WAN's (NAT Public)
lease time for its current IP address.
Applicable only when NAT is enabled. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.206 |
| region Set Region Code for the Unit. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.207 |
| regionAsia Country Code for Asia. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.208 |
| regionEurope Country Code for Europe. Other is only available for units with EU Region Lock. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.209 |
| removeVlanMember Write-only OID,Enter VLAN ID which needs to deleted.
If Vlan doesnot exist an error will be returned. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.21 |
| regionNorthAmerica Country Code for North America. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.210 |
| regionOceania Country Code for Oceania. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.211 |
| regionSouthAmerica Country Code for South America. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.212 |
| regionOtherRegulatory Regulatory setting for governing regulatory body. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.213 |
| interleave Engineering use only. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.214 |
| receiveQualityDebug Enable or disable receive quality calculations for every packet.
Enabling(1) will calulate receive quality on all receiving packets. Due to load on CPU, will slightly packet per … | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.215 |
| apType In standard mode, all possible sync sources will be made availble and usedfor autoSync operation.
In remote mode, sync over power port will not be available as a sync source.
Remo… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.216 |
| regionAfrica Country Code for Africa. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.217 |
| addCustomFreqMimo Frequency input ie) 3700.50. Deprecated, please use 'addCustomFreqList'. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.218 |
| removeCustomFreqMimo Frequency input ie) 3700.50. Deprecated, please use 'removeCustomFreqList'. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.219 |
| scheduling To use hardware or software scheduling | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.22 |
| timedSpectrumAnalysisDurationBox Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.220 |
| spectrumAnalysisActionBox Start or stop timed or continuous Spectrum Analysis and also give status.
(0) - Stop Spectrum Analysis
(1) - Start Timed Spectrum Analysis
Note: AP/BHM will run Spectrum Analysis … | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.221 |
| mac1VIDMapPriority VID priority for Entry 1 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.222 |
| mac1VIDMapPriorityMode VID priority Mode for Entry 1 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.223 |
| mac2VIDMapPriority VID priority for Entry 2 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.224 |
| mac2VIDMapPriorityMode VID priority Mode for Entry 2 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.225 |
| mac3VIDMapPriority VID priority for Entry 3 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.226 |
| mac3VIDMapPriorityMode VID priority Mode for Entry 3 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.227 |
| mac4VIDMapPriority VID priority for Entry 4 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.228 |
| mac4VIDMapPriorityMode VID priority Mode for Entry 4 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.229 |
| transmitterOP Transmitter output power. This is not available on OFDM SMs.
Not applicable for PMP 450m. See EIRP OID. | scalar | dBm Integer32 | .1.3.6.1.4.1.161.19.3.3.2.23 |
| mac5VIDMapPriority VID priority for Entry 5 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.230 |
| mac5VIDMapPriorityMode VID priority Mode for Entry 5 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.231 |
| mac6VIDMapPriority VID priority for Entry 6 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.232 |
| mac6VIDMapPriorityMode VID priority Mode for Entry 6 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.233 |
| mac7VIDMapPriority VID priority for Entry 7 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.234 |
| mac7VIDMapPriorityMode VID priority Mode for Entry 7 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.235 |
| mac8VIDMapPriority VID priority for Entry 8 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.236 |
| mac8VIDMapPriorityMode VID priority Mode for Entry 8 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.237 |
| mac9VIDMapPriority VID priority for Entry 9 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.238 |
| mac9VIDMapPriorityMode VID priority Mode for Entry 9 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.239 |
| bridgeEnable Disable or enable bridging functionality for a BH unit. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.24 |
| mac10VIDMapPriority VID priority for Entry 10 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.240 |
| mac10VIDMapPriorityMode VID priority Mode for Entry 10 in MAC Address VID Mapping Table. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.241 |
| managementVIDPriority management VID VID VLAN Priority. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.242 |
| managementVIDPriorityMode management VID VLAN Priority Mode. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.243 |
| remarkSrcVID Source VID to apply remarking on. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.244 |
| addRemarkVID Add VLAN ID re-marking entry. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.245 |
| addRemarkPriority Add 802.1p re-mark entry. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.246 |
| deleteRemarkVID Remove the VID re-marking for this source VID. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.247 |
| deleteRemarkPriority Remove the priority re-marking for this source VID. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.248 |
| mimoRateAdaptAlgorithm Engineering use only.
Control MIMO Rate Adapt Algorithm
0 = MIMO-A/B This chooses MIMO-A or MIMO-B dynamically to maximize throughput
1 = MIMO-B only
2 = MIMO-A only
3 = SISO only | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.249 |
| fecEnable Disable or enable FEC error correction functionality
for multipoint units. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.25 |
| controlMessages Control Messages (Beacon/Scheduling Map/Acknowledgements/Broadcast)
0 = MIMO-A
1 = SISO
MIMO Control Messages is the recommended and default setting.
However, SISO Control Message… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.250 |
| enableSecurityBanner Shows Security Banner at the time of login | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.251 |
| vcDepth VC Depth of radio. Not applicable with 450m.
Engineering use only. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.252 |
| textSecurityBanner Security Banner to be dispalyed on login page.
Length should be maximum 1200 characters.Configuration from web UI can enter upto 1499 characters.
Only ASCII characters(0-9a-zA-Z,C… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.253 |
| acceptSecurityBanner 1: User must accept and acknowledge security banner before login.
0: Accepting security banner is not mandatory and user can login without it. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.254 |
| poeT2Classification When disabled, the radio will ignore the 802.3at Type 2 classification. When enabled,
if 802.3at Type 2 PoE is not present, the board will start and log the problem but the
tran… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.255 |
| simulatedAirDelay Simulated Air Delay. Engineering use only. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.256 |
| cnMaestroEnable Enable Remote management using cnMaestro. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.257 |
| cnMaestroUrl cnMaestro Server URL. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.258 |
| camID Cambium Id for cnMaestro onboarding. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.259 |
| trapIP1 obsolete Obsoleted. Configure with whispBoxDNS.trap1. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.26 |
| camOnboardKey Onboarding key for cnMaestro onboarding. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.260 |
| atexHazlocPowerLimit If radio is keyed for ATEX/HazLoc operation, these settings can
be used to limit maximum power output, per Gas Group specs. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.261 |
| nearFieldOperation Enables operation in the near field. This is
effective only when an EIRP of 22 dBm or lower
is selected or when Engineering keyed.
PMP 450m only. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.263 |
| defaultIPAccessEnable Enable(1) or Disable(0) Default alternative LAN1 IP address | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.264 |
| pingWdogEnable enable(1) or disable(0) ping watchdog. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.265 |
| pingWdogIP IPv4 address to ping in dotted decimal notation. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.266 |
| pingWdogInterval Intervals in seconds at which ping should be initiated. | scalar | Seconds Integer32 | .1.3.6.1.4.1.161.19.3.3.2.267 |
| pingWdogRbtCnt Ping Failures count at which reboot should be initiated. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.268 |
| trapIP2 obsolete Obsoleted. Configure with whispBoxDNS.trap2. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.27 |
| forceReassessment Forces channel reassessment for all registered SMs.
This is effective only when an EIRP of 22 dBm or lower
is selected or when Engineering keyed.
MU-MIMO only. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.275 |
| enable8023linkBox To enable or disable 802.3 link. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.276 |
| ethernetPortSelection Set/Get the Ethernet port used to bridge traffic. PMP 450m only. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.278 |
| ethernetLinkSpeedSfp Set/Get Ethernet link speed and duplex settings of the SFP port. PMP 450m only. Please note that the Radio Recovery Console only supports auto1000F for the SFP. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.279 |
| trapIP3 obsolete Obsoleted. Configure with whispBoxDNS.trap3. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.28 |
| trapIP4 obsolete Obsoleted. Configure with whispBoxDNS.trap4. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.29 |
| displayOnlyAccess obsolete This variable is deprecated. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.3 |
| trapIP5 obsolete Obsoleted. Configure with whispBoxDNS.trap5. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.30 |
| trapIP6 obsolete Obsoleted. Configure with whispBoxDNS.trap6. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.31 |
| trapIP7 obsolete Obsoleted. Configure with whispBoxDNS.trap7. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.32 |
| trapIP8 obsolete Obsoleted. Configure with whispBoxDNS.trap8. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.33 |
| trapIP9 obsolete Obsoleted. Configure with whispBoxDNS.trap9. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.34 |
| trapIP10 obsolete Obsoleted. Configure with whispBoxDNS.trap10. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.35 |
| commStringRWrite Read/Write Community string. This is a write-only OID. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.36 |
| subnetMask Subnet mask for the management IP 1. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.37 |
| mngtIP Management IP address 1. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.38 |
| allowVIDAccess Allow or disallow local SM management VID access. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.39 |
| fullAccess Full access password. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.4 |
| setDefaultPlug If enabled parameters are set to Factory Defaults upon default plug mode detection. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.40 |
| hwsCompatibility obsolete If enable, it ensures 6.0 compatibility with HWS. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.41 |
| gpsInput Values 1, 2, 3 have been deprecated.
(0) Generate AP sync signal.
(1) Deprecated. Sync AP to received signal (Timing Port/UGPS). It will set AutoSync.
(2) Deprecated. Sync AP to r… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.42 |
| ism Enable ISM on 5.7GHz frequency band radios. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.43 |
| hiPriority obsolete Enable Hi Priority Data Queue on BH radios. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.44 |
| userName User name.To create read-only user set userMode OID first.
Maximum of 4 users can exist in system. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.45 |
| userPassword User password.To create read-only user set userMode OID first. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.46 |
| userAccessLevel User access level.To create read-only user set userMode OID first.
1=TECH
2=INSTALL
3=ADMIN | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.47 |
| deleteUser User name to remove. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.48 |
| twoXRate obsolete To enable or disable double rate. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.49 |
| webAutoUpdate Web page auto update in seconds. 0 means disabled. | scalar | Seconds Integer32 | .1.3.6.1.4.1.161.19.3.3.2.5 |
| lanDhcpState To enable or disable LAN Interface DHCP feature. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.50 |
| sessionTimeout Timer for Telnet, Web and FTP sessions. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.51 |
| vlanMemberSource Specified the VLAN member source to display. 0=configured, 1=active configuration.
Note that this OID is internal to SNMP and is not available at the Web Interface. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.52 |
| addCustomFreqList Add Custom Frequencies.
The frequencies can be in a variety of units up to KHz.
Frequencies can be added in a list separated by commas.
Example: 3550, 356000, 3450001.
A get wil… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.53 |
| removeCustomFreqList Remove Custom Frequencies.
The frequencies can be in a variety of units up to KHz.
Frequencies can be removed in a list separated by commas.
Example: 3550, 356000, 3450001.
A get … | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.54 |
| allowColocation obsolete Allow or disallow Colocation for software scheduling Backhaul Timing Masters with hardware scheduling Backhaul Timing Masters. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.55 |
| changeUsrPwd Allow to change the password of a given user of a given user. Usage: userName,password. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.56 |
| mngtIP2 Management IP address 2. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.57 |
| subnetMask2 Subnet mask for the management IP 2. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.58 |
| mngtIP3 Management IP address 3. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.59 |
| pass1Status Password 1(display only) status. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.6 |
| subnetMask3 Subnet mask for the management IP 3. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.60 |
| mngtIP4 Management IP address 4. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.61 |
| subnetMask4 Subnet mask for the management IP 4. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.62 |
| mngtIP5 Management IP address 5. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.63 |
| subnetMask5 Subnet mask for the management IP 5. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.64 |
| mngtIP6 Management IP address 6. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.65 |
| subnetMask6 Subnet mask for the management IP 6. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.66 |
| mngtIP7 Management IP address 7. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.67 |
| subnetMask7 Subnet mask for the management IP 7. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.68 |
| mngtIP8 Management IP address 8. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.69 |
| pass2Status Password 2(full access) status. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.7 |
| subnetMask8 Subnet mask for the management IP 8. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.70 |
| mngtIP9 Management IP address 9. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.71 |
| subnetMask9 Subnet mask for the management IP 9. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.72 |
| mngtIP10 Management IP address 10. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.161.19.3.3.2.73 |
| subnetMask10 Subnet mask for the management IP 10. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.74 |
| bhvlanEnable To enable or disable VLAN for Backhaul Master/Slave. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.75 |
| lldpBroadcastEnable To enable Broadcast of LLDP message, if disabled LLDP uses multicast | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.76 |
| regionCode deprecated Set Region Code for the Unit. Used the individual region[Region] OIDs instead. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.77 |
| russiaRegion deprecated Set Category Region for Russian 5.9/6.05 GHz Radio Only. Use setting under regionAsia now. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.78 |
| commStringROnly Set Read Only commnunity string. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.79 |
| bridgeEntryTimeout Bridge table time out Range : 25 -- 1440 Minutes. | scalar | minutes Integer32 | .1.3.6.1.4.1.161.19.3.3.2.8 |
| ethernetLinkSpeed Set/Get Ethernet link speed and duplex settings. Note that the Gigabit options are only valid for boards that support Gigabit speeds. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.80 |
| cyclicPrefix Cyclic Prefix value, for OFDM Radios only.
Deprecated for MIMO SMs. For PMP 430 SMs, this value is only used while in PMP 430 mode (1/16 is forced in PMP 450 mode). | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.81 |
| numberCustomFreq Number of custom frequencies added.
There is a maximum of 100.
For use on 3.5 GHz OFDM Radios only. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.82 |
| channelBandwidth The current channel bandwidth in MHz.
For use on OFDM Radios only.
Obsoleted for MIMO SMs. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.83 |
| setDefaults Setting this to 1 will set the radio to Factory Defaults after the next reboot. Setting this to 0
will undo Factory Defaults if and only if Factory Defaults have been set previou… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.84 |
| radioRateAdapt Rate adaptation parameter
0: 1x No rate adaptation (FSK and SISO OFDM QPSK)
1: 1x/2x (FSK and SISO OFDM 16-QAM)
Following are OFDM only:
2: 1x/2x/3x (SISO OFDM 64-QA… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.85 |
| siteInfoViewable Enable non login users the ability to view Site Information | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.86 |
| largeVCQ Enable or disable Large VC Qs for SM or PTP radios. Enable when Uplink is being used for camera video feed. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.87 |
| latitude The latitude setting of this unit in decimal degrees. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.88 |
| longitude The longitude setting of this unit in decimal degrees. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.2.89 |
| snmpMibPerm Read/Write permission for MIB groups. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.9 |
| height The height setting of this unit in meters. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.90 |
| bandwidth Radio bandwidth setting.
Obsoleted for MIMO SMs. Instead for MIMO SMs use OID bandwidthScan. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.91 |
| dataScramblingMethod obsolete This OID is for OFDM only and is obsolete. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.92 |
| portVID Backhaul Port VID (PVID). | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.93 |
| radioRateAdaptUL Uplink Rate adaptation parameter
0: 1x No rate adaptation (FSK and SISO OFDM QPSK)
1: 1x/2x (FSK and SISO OFDM 16-QAM)
Following are OFDM only:
2: 1x/2x/3x (SISO OFD… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.2.94 |
| providerVID Provider VID for QinQ VLAN. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.95 |
| mac1VIDMapAddr MAC Address for Entry 1 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.96 |
| mac1VIDMapVid VID for Entry 1 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.97 |
| mac2VIDMapAddr MAC Address for Entry 2 in MAC Address VID Mapping Table. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.161.19.3.3.2.98 |
| mac2VIDMapVid VID for Entry 2 in MAC Address VID Mapping Table. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.2.99 |