linkTestModeBox
WHISP-BOX-MIBV2-MIB ·
.1.3.6.1.4.1.161.19.3.3.18.1.5
Object
scalar
r/w
Enumeration
Link Test Mode 0 = Link Test without Bridging 1 = Link Test with Bridging 2 = Link Test with Bridging and MIR 3 = Extrapolated Link Test (send only a few packets measuring their quality and extrapolate out the throughput) This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. Extrapolated Link Test is not available for FSK radios. 4 = Link Test with Multiple VCs (traffic sent to all registered VCs, or specified VCs) - PMP 450m only
Context
- MIB
- WHISP-BOX-MIBV2-MIB
- OID
.1.3.6.1.4.1.161.19.3.3.18.1.5- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- whispBoxLinkTestConfig
- Siblings
- 13
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | linktestwithoutbridging |
1 | linktestwithbridging |
2 | linktestwithbridgingandmir |
3 | extrapolatedlinktest |
4 | linktestwithmultipleVCs |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| linkTestLUIDBox LUID selection for Link Test. Valid range: 2-255. Read-Only for SM or Backhaul slave, Read/Write for AP. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.18.1.1 |
| linkTestDirectionBox Link Test Direction - Engineering Use Only
0 = default (will do bidirectional)
1 = Uplink Only
2 = Downlink Only
3 = Bi-Directional (same as 0, setting to 3 will result in setting… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.18.1.10 |
| linkTestFloodModeBox PMP 450m only. Engineering use only.
Link Test usage:
0 = Packets will be sent out the SM ethernet port
1 = Packets will not be sent out the SM ethernet port | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.18.1.11 |
| linkTestMumimoBox PMP 450m only.
Link Test usage:
0 = MU-MIMO disabled (legacy or sector mode)
1 = MU-MIMO enabled | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.18.1.12 |
| linkTestVCListBox PMP 450m only.
Link Test usage:
Enter VCs to be tested (eg. 18 - 22,24,32)
Empty field or 0 will flood all registered VCs for duration of test | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.161.19.3.3.18.1.13 |
| linkTestSMRestriction Control access to SM initiated Link Tests.
Disabling will permit all Link Tests initiated at the SM.
Enabling will only permit Link Tests that allow user traffic to pass.
PMP only. | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.18.1.14 |
| linkTestDurationBox Duration for the Link Test. Valid range: 2-10 seconds | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.18.1.2 |
| linkTestActionBox Setting value 1 will initiate link test. Note that trying to set 0 will not stop the test.
In fact it will return an error message. The value of 0 just indicates the idle state
me… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.18.1.3 |
| linkTestPktLengthBox Packet length for Link Test. Valid range: 64-1714 bytes | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.18.1.4 |
| linkTestSNRCalculationBox Enable or disable Signal to Noise Ratio (SNR) calculations during a Link Test.
Enabling(1) will calulate SNR on all receiving packets.
Due to load on CPU, will slightly degrade pa… | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.18.1.6 |
| linkTestWithDualPathBox Link Test with:
0 = Low Priority VC only
1 = High and Low Priority VCs | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.18.1.7 |
| linkTestNumPktBox Number of packets to send. Valid range: 0-64 where 0 will
flood the link for the duration of the test. | scalar | Integer32 | .1.3.6.1.4.1.161.19.3.3.18.1.8 |
| linkTestForceModulationBox Engineering use only.
Link Test with:
0 = Normal Rate Adapt algorithm
1 = Force to max modultion - No Rate Adapt Algorithm | scalar | Enumeration | .1.3.6.1.4.1.161.19.3.3.18.1.9 |