ifTableXtndType
WAN-MIB ·
.1.3.6.1.4.1.6889.2.1.6.2.2.1.1.41
Object
column
r/w
Enumeration
Extended type is, currently, required for modem interfaces
Context
- MIB
- WAN-MIB
- OID
.1.3.6.1.4.1.6889.2.1.6.2.2.1.1.41- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ifTableXtndEntry
- Table
- ifTableXtndTable
- Siblings
- 40
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | nullModem |
2 | usrSporsterModem |
3 | multitechZbaModem |
4 | multitechIsdnModem |
255 | notSupported |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ifTableXtndIndex The index in the ifTable for which this row
is providing information. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.1 |
| ifTableXtndDTELoopback This object is only applicable for rs232-like
synchronuos DTE interefaces.
It determines the status of the DTE loopback. | column | OnOff | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.10 |
| ifTableXtndIgnoreDCD This object is only applicable for rs232-like
synchronuos DTE interefaces.
This command configures the serial interface
to monitor the DSR/CTS signals, instead of
DCD signal, as … | column | OnOff | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.11 |
| ifTableXtndIdleChars This object is only applicable for rs232-like
synchronuos DTE interefaces.
This command sets the bit pattern used to
indicate an idle line. | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.12 |
| ifTableXtndBandwidth This object is used to determine the bandwidth
of the interface, in Kbps, for interfaces that
support it.
This information is informational, and does not
affect t… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.13 |
| ifTableXtndEncapsulation Applicable only to layer 1 interfaces.
The type of the layer 2 interface on top of this
Interface.
ppp - The Layer 2 interface is PPP
frameRelay - The Layer 2 inter… | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.14 |
| ifTableXtndOperStatus An extension to ifOperStatus, for showing faults
and partial faliures, including aggregation of upper
layer faults (up to but not including L3).
The following Pseudo code descri… | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.15 |
| ifTableXtndBackupCapabilities Determines what roles an interface can play in a backup
relation. This should be filled per interface,
according to its capabilities.
primaryAndBackup - the interf… | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.16 |
| ifTableXtndBackupIf The ifIndex of the backup interface for this primary
interface.
0 if no backup is defined.
The agent will not permit setting this value, if:
The in… | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.17 |
| ifTableXtndBackupEnableDelay The delay (in Secs) that a primary interface must be
inactive before its backup interface is activated.
Configurable on the primary interface only. | column | Integer32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.18 |
| ifTableXtndBackupDisableDelay The delay (in Secs) between the primary coming back to
life and its activation and de-activation of its
backup interface.
The value '-1' means that the primary is never
re-acti… | column | Integer32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.19 |
| ifTableXtndPeerAddress The IP Address of the peer device on
the link identified by this ifIndex.
This value is only meaningful for
point to point links. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.2 |
| ifTableXtndPrimaryIf On a backup interface, this will point to the primary
interface. '0' means no primary interface. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.20 |
| ifTableXtndCarrierDelay This command sets the carrier delay on a serial
interface in seconds. If a link goes down and comes
back up before the carrier delay timer expires, the
down state is effectively… | column | Integer32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.21 |
| ifTableXtndDtrRestartDelay Determines the period in seconds for deactivating
DTR signal when the serial line is inactive. | column | Integer32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.22 |
| ifTableXtndDtrPulseTime Determines the interval in milliseconds DTR signal is
held inactive when the serial line is inactive. | column | Integer32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.23 |
| ifTableXtndLoadInterval Determines interval (in secs) for exponential averages
calculations for an interface.
Must be a multiple of 30. | column | Integer32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.24 |
| ifTableXtndInputRate Expoential Average of the Number of bits
received per second calculated for the interval
specified in ifTableXtndLoadInterval.
The exponentail average smooths peaks while corre… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.25 |
| ifTableXtndOutputRate Expoential Average of the Number of bits
sent per second calculated for the interval
specified in ifTableXtndLoadInterval.
The exponentail average smooths peaks while correctly… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.26 |
| ifTableXtndInputLoad Expoential Average of the Input Load calculated for the interval
specified in ifTableXtndLoadInterval.
Load is expressed a a number in the range 1 to 255.
255 = 100% utilization … | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.27 |
| ifTableXtndOutputLoad Expoential Average of the Output Load calculated for the interval
specified in ifTableXtndLoadInterval.
Load is expressed a a number in the range 1 to 255.
255 = 100% utilization… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.28 |
| ifTableXtndReliability Expoential Average of the Reliability of an interface
calculated for the interval specified in
ifTableXtndLoadInterval.
Reliability is expressed a a number in the … | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.29 |
| ifTableXtndVoIPQueue Turns voip-queueing on or off or turn fair-queuing on. | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.3 |
| ifTableXtndTrafficShaperRate This item controls a traffic shaper on the interface.
Its value is the shaping rate in bits per seconds.
When zero, the shaper is disabled | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.30 |
| ifTableXtndCacBBL Dynamic CAC Bearer Bandwidth Limit in
kilo-bits-per-seconds. This item equals -1 when dynamic CAC
is not configured. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.31 |
| ifTableXtndCacPriority If more than one interface with configured BBL is up,
the gateway reports the BBL of the interface with the highest
activation priority value. If N active interfaces shares the … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.32 |
| ifTableXtndCacifStatus Dynamic CAC status of the interface. | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.33 |
| ifTableXtndCommonApplifStatus Supported Application on this Interface.
If 0 value - Not supported else supported.
Bit 0 - Unknown Application.
Bit 1 - Support of Next Hop Interface in Policy Based Routing Ap… | column | OctetString | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.34 |
| ifTableXtndIpSecDfBit This item controls whether the DF (don't fragment) bit of incoming packets
is copied to the external IPSec header | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.35 |
| ifTableXtndMinPmtu Set the minimal PMTU for IPSec tunnels. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.36 |
| ifTableXtndConfString An additional configuration string for the interface.
init-string - for modem interfaces | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.37 |
| ifTableXtndPppIpcpDnsOptionRequest PPP-IPCP DNS option request. Configuration whether during the PPP-IPCP
negotiation the DNS option will be requested. Default: Disable.
The DNS information gathered will be used b… | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.38 |
| ifTableXtndKeepaliveTrackId Bind the status of this interface to an object-tracker by specifying
the ID of the object-tracker (avstrTrackerId in
AVAYA-SAA-TRACK-MIB).
A value of 0 means that interface is no… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.39 |
| ifTableXtndCableLength Cable length attenuation on this interface. | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.4 |
| ifTableXtndFrTrafficShaping This object determines / indicates whether Frame-Relay
Traffic-Shaping is enabled (on) or disabled (off) for this
interface.
This object can be set only for interfaces, but not fo… | column | OnOff | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.40 |
| ifTableXtndGain The gain on this interface. | column | Enumeration | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.5 |
| ifTableXtndDescription This object is a Read-Write equivalent
of ifDescr. It is used to enable users
to change the value of ifDescr. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.6 |
| ifTableXtndKeepAlive Time, in seconds, between keepalive messages.
0 means keepalive should not be used, or is not
supported. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.7 |
| ifTableXtndMtu This object is a R/W copy of the ifMtu
object from the ifTable.
It enables changing of the MTU for
interfaces that allow this. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.8 |
| ifTableXtndInvertTxClock This object is only applicable for rs232-like
synchronuos DTE interefaces.
It determines whether the transmit clock
is inverted. | column | OnOff | .1.3.6.1.4.1.6889.2.1.6.2.2.1.1.9 |