upsAddlFuncsStatusOperational

UPS2-MIB · .1.3.6.1.4.1.52.4.1.1.10.9.1.1.5
MIB view Table view

Object

column mandatory Integer32 
This object contains 8 bits of information about the current
operational status of the UPS.  The bits are encoded as
follows:
              
BIT 7:  1=UPS ready to power load upon return of normal line
          or upon user command
BIT 6:  1=UPS ready to power load upon user command
BIT 5:  1=UPS in bypass mode as a result of manual bypass
          control
BIT 4:  1=UPS is returning from bypass mode
BIT 3:  1=UPS in bypass mode as a result of UPS-Link or
          key command
BIT 2:  1=UPS going to bypass mode as a result of UPS-Link
          or key command
BIT 1:  1=not defined
BIT 0:  1=wakeup mode - startup test lasting < 2 sec
              
Note that bit 0 is the low-order bit.

Context

MIB
UPS2-MIB
OID
.1.3.6.1.4.1.52.4.1.1.10.9.1.1.5
Type
column
Access
readonly
Status
mandatory
Parent
upsAddlFuncsEntry
Table
upsAddlFuncsTable
Siblings
8

Syntax

Integer32
Source
COPS-PR-SPPIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
upsAddlFuncsNumBatteryPacks mandatory
The number of battery pack units connected to the UPS.
columnInteger32.1.3.6.1.4.1.52.4.1.1.10.9.1.1.1
upsAddlFuncsNumBadBatteryPacks mandatory
The number of bad (faulty) battery pack units connected to the UPS.
columnInteger32.1.3.6.1.4.1.52.4.1.1.10.9.1.1.2
upsAddlFuncsOutputCurrent mandatory
The true rms load current drawn from the UPS. The value of this object is the actual amperage * 100 (that is, to determine the actual amperage, divide the value of this object by…
columnInteger32.1.3.6.1.4.1.52.4.1.1.10.9.1.1.3
upsAddlFuncsOutputApparentPower mandatory
The UPS's output load represented as a percentage of full rated load in Volt-Amps. The value of this object is the actual percentage * 10 (that is, to determine the actual perc…
columnInteger32.1.3.6.1.4.1.52.4.1.1.10.9.1.1.4
upsAddlFuncsStatusFault mandatory
This object contains 8 bits of information about the current fault conditions of the UPS. The bits are encoded as follows: BIT 7: reserved for future use BIT 6: …
columnInteger32.1.3.6.1.4.1.52.4.1.1.10.9.1.1.6
upsAddlFuncsConfigPassword mandatory
The password that controls access to the UPS's LCD display. A maximum of 4 characters may be entered.
columnOctetString.1.3.6.1.4.1.52.4.1.1.10.9.1.1.7
upsAddlFuncsConfigDisable mandatory
This object may be written to immediately shut down the UPS, requiring a manual reset. Reading this object will always return a 0.
columnEnumeration.1.3.6.1.4.1.52.4.1.1.10.9.1.1.8
upsAddlFuncsConfigBypass mandatory
This object may be written to cause the UPS to transfer to or from the bypass mode. Reading this object will always return a 0.
columnEnumeration.1.3.6.1.4.1.52.4.1.1.10.9.1.1.9