sbiUplinkBDuplex
TIMETRA-SAS-SYSTEM-MIB ·
.1.3.6.1.4.1.6527.6.2.2.2.5.11.25
Object
scalar
r/w
Enumeration
The value of sbiDuplex specifies the duplex mode for the uplinkB port. This value is ignored if auto-negotiation is enabled.
Context
- MIB
- TIMETRA-SAS-SYSTEM-MIB
- OID
.1.3.6.1.4.1.6527.6.2.2.2.5.11.25- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- sysSASBofInfo
- Siblings
- 22
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | full |
2 | half |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sbiUplinkAPort Primary bof port used for autoconfig. When set to zero
'uplinAport' would be reset | scalar | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.6527.6.2.2.2.5.11.1 |
| sbiUplinkBVlan Vlan tag to be used on uplinkB, if set to -1 packets are sent out without
vlan tag | scalar | Integer32 | .1.3.6.1.4.1.6527.6.2.2.2.5.11.10 |
| sbiPingAddress IP address to be used for ping-test after booting. This is the
last step in the auto-init process | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6527.6.2.2.2.5.11.11 |
| sbiUplinkRouteTable The sbiUplinkRouteTable contains an entry for each static route
configured for the given uplink A or B. These static routes are
only used during the system bootup | table | - | .1.3.6.1.4.1.6527.6.2.2.2.5.11.12 |
| sbiNoServicePortOne The value of sbiNoServicePortOne indicates service traffic
on the port identified by this InterfaceIndex is disabled. | scalar | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.6527.6.2.2.2.5.11.13 |
| sbiNoServicePortTwo The value of sbiNoServicePortTwo indicates service traffic
on the port identified by this InterfaceIndex is disabled. | scalar | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.6527.6.2.2.2.5.11.14 |
| sbiUplinkAdminMode sbiUplinkAdminMode when set to access-uplink, bof uplink would be used
in l2 mode,the default mode is network | scalar | Enumeration | .1.3.6.1.4.1.6527.6.2.2.2.5.11.15 |
| sbiUplinkOperMode sbiUplinkOperMode is operational mode of the system. This object is
initialized during system bootup based on sbiUplinkAdminMode setting | scalar | Enumeration | .1.3.6.1.4.1.6527.6.2.2.2.5.11.16 |
| sbiExpansionCardType sbiExpansionCardType identifies the expansion card type to the system
before boot up. The system will not allow for provisioning of a different
MDA than the one currently specifie… | scalar | Enumeration | .1.3.6.1.4.1.6527.6.2.2.2.5.11.17 |
| sbiConsoleDisabled The value of sbiConsoleDisabled determines whether or not the
system console is disabled. When set to 'true' console is disabled. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.2.2.2.5.11.18 |
| sbiPassword sbiPassword is used to enable the user to configure the bof
password. | scalar | OctetString | .1.3.6.1.4.1.6527.6.2.2.2.5.11.19 |
| sbiUplinkAIpAddr Primary bof port ip address | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6527.6.2.2.2.5.11.2 |
| sbiUplinkAAutoNegotiate The value of sbiUplinkAAutoNegotiate determines whether or not the
speed and duplex parameters will be automatically negotiated
on the uplinkAport. When set to 'true', auto-negoti… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.2.2.2.5.11.20 |
| sbiUplinkASpeed The value of sbiSpeed specifies the speed of the uplinkA
port. This value is ignored if auto-negotiation is enabled. | scalar | Mbps Unsigned32 | .1.3.6.1.4.1.6527.6.2.2.2.5.11.21 |
| sbiUplinkADuplex The value of sbiDuplex specifies the duplex mode for the
uplinkA port. This value is ignored if auto-negotiation is
enabled. | scalar | Enumeration | .1.3.6.1.4.1.6527.6.2.2.2.5.11.22 |
| sbiUplinkBAutoNegotiate The value of sbiUplinkBAutoNegotiate determines whether or not the
speed and duplex parameters will be automatically negotiated
on the uplinkBport. When set to 'true', auto-negoti… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.2.2.2.5.11.23 |
| sbiUplinkBSpeed The value of sbiSpeed specifies the speed of the uplinkB
port. This value is ignored if auto-negotiation is enabled. | scalar | Mbps Unsigned32 | .1.3.6.1.4.1.6527.6.2.2.2.5.11.24 |
| sbiUplinkAMask The value of sbiActiveIpMask specifies the mask length of the
subnet associated with the IP address of the primary bof port. | scalar | TN-TC-MIBIpAddressPrefixLength | .1.3.6.1.4.1.6527.6.2.2.2.5.11.3 |
| sbiUplinkAVlan Vlan tag to be used on uplinkA, if set to -1 packets are sent out without
vlan tag | scalar | Integer32 | .1.3.6.1.4.1.6527.6.2.2.2.5.11.5 |
| sbiUplinkBPort Secondary bof port used for autoconfig. When set to zero
'uplinBport' would be reset | scalar | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.6527.6.2.2.2.5.11.6 |
| sbiUplinkBIpAddr Secondary bof port ip address | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6527.6.2.2.2.5.11.7 |
| sbiUplinkBMask The value of sbiActiveIpMask specifies the mask length of the
subnet associated with the IP address of the bof uplink B port. | scalar | TN-TC-MIBIpAddressPrefixLength | .1.3.6.1.4.1.6527.6.2.2.2.5.11.8 |