swFCPortDisableReason
SW-MIB ·
.1.3.6.1.4.1.1588.2.1.1.1.6.2.1.40
Object
column
Enumeration
It indicates the state change reason when port goes from online to offline
Context
- MIB
- SW-MIB
- OID
.1.3.6.1.4.1.1588.2.1.1.1.6.2.1.40- Type
- column
- Access
- noaccess
- Status
- current
- Parent
- swFCPortEntry
- Table
- swFCPortTable
- Siblings
- 36
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | r-recover-fail |
2 | r-invalid-reason |
3 | r-forced |
4 | r-sw-disabled |
5 | r-bl-disabled |
6 | r-slot-off |
7 | r-sw-enabled |
8 | r-bl-enabled |
9 | r-slot-on |
10 | r-persistid |
11 | r-sw-violation |
12 | r-prv-dev-violation |
13 | r-pub-dev-violation |
14 | r-port-data-fail |
15 | r-online-incomplete |
16 | r-online-route-fail |
17 | r-inconsistent |
18 | r-set-vcc-fail |
19 | r-ecp-in-testing |
20 | r-elp-in-testing |
21 | r-ecp-retries-exceeded |
22 | r-invalid-ecp-state |
23 | r-bad-ecp-rcvd |
24 | r-send-rtmark-fail |
25 | r-send-ecp-fail |
26 | r-save-link-rtt-fail |
27 | r-em-incnst |
28 | r-pci-attach-fail |
29 | r-buf-starv |
30 | r-elp-fctl-mismatch |
31 | r-eport-disabled |
32 | r-trunk-with-vcxlt |
33 | r-sw-fl-port-not-ready |
34 | r-link-reinit |
35 | r-domain-id-change |
36 | r-auth-rejected |
37 | r-auth-timeout |
38 | r-auth-fail-retry |
39 | r-fcr-conf-mismatch1 |
40 | r-fcr-conf-mismatch2 |
41 | r-fcr-port-ld-mode-mismatch |
42 | r-fcr-ld-credit-mismatch |
43 | r-fcr-set-vcc-failed |
44 | r-fcr-set-rtc-failed |
45 | r-fcr-elp-ver-inconsis |
46 | r-fcr-elp-fctl-mismatch |
47 | r-fcr-pid-mismatch |
48 | r-fcr-tov-mismatch |
49 | r-fcr-ld-incompat |
50 | r-fcr-isolated |
51 | r-elp-retries-exceeded |
52 | r-fcr-exports-exceeded |
53 | r-fcr-license |
54 | r-fcr-conf-ex |
55 | r-fcr-ftag-over |
56 | r-fcr-ftag-conflict |
57 | r-fcr-fowner-conflict |
58 | r-fcr-zone-resource |
59 | r-fcr-port-state-to |
60 | r-fcr-authn-reject |
61 | r-fcr-sec-fcs-list |
62 | r-fcr-sec-failure |
63 | r-fcr-incompatible-mode |
64 | r-fcr-sec-scc-list |
65 | r-fcr-generic |
66 | r-sw-ex-port-not-ready |
67 | r-fcr-class-f-incompat |
68 | r-fcr-class-n-incompat |
69 | r-fcr-invalid-flow-rcvd |
70 | r-fcr-state-disabled |
71 | r-fdd-strict-exist |
72 | r-last-port-disable-msg |
73 | r-sw-l-port-not-support |
74 | r-peer-port-in-di-zone |
75 | r-zone-incompat |
76 | r-sw-config-l-port-not-support |
77 | r-sw-port-mirror-configured |
78 | r-nportlogin-inprogress |
79 | r-nonpiv |
80 | r-nomapping |
81 | r-unknowntype |
82 | r-nportoffline |
83 | r-flogifailed |
84 | r-nportbusy |
85 | r-noflogi |
86 | r-noflogiresp |
87 | r-flogidupalpa |
88 | r-loopcfg |
89 | r-noenclicense |
90 | r-nofiportmapping |
91 | r-brcdfabconn |
92 | r-port-reset |
93 | r-floginport |
94 | r-fdd-strict-conflict |
95 | r-fdd-cfg-conflict |
96 | r-fdd-cfg-conflict-na-neigh |
97 | r-fcr-insistent-front-did-mismatch |
98 | r-fcr-fabric-binding-failure |
99 | r-fcr-non-standard-domain-offset |
100 | r-area-in-use |
101 | r-mstr-diff-pg |
102 | r-mstr-diff-area |
103 | r-ta-not-supported |
104 | r-eport-not-supported |
105 | r-fport-not-supported |
106 | r-cfg-not-supported |
107 | r-port-ll-th-exceeded |
108 | r-port-synl-th-exceeded |
109 | r-port-pe-th-exceeded |
110 | f-port-disable-no-trk-lic |
111 | r-port-inw-th-exceeded |
112 | r-port-crc-th-exceeded |
113 | f-port-tr-disable-speed-not-ok |
114 | r-port-auto-disable |
115 | r-fcr-export-in-non-base-sw |
116 | r-base-switch-supports-no-device |
117 | r-port-trunk-proto-error |
118 | r-no-area-avail |
119 | r-cannot-unbind-existing-area |
120 | r-cannot-use-10bit-area |
121 | r-authentication-required |
122 | r-port-lr-th-exceeded |
123 | r-fcr-export-lf-conflict |
124 | r-incompat |
125 | r-did-overlap |
126 | r-zone-conflict |
127 | r-eport-seg |
128 | r-no-license |
129 | r-platform-db |
130 | r-sec-incompat |
131 | r-sec-violation |
132 | r-ecp-longdist |
133 | r-dup-wwn |
134 | r-eport-isolated |
135 | r-ad |
136 | r-esc-did-offset |
137 | r-esc-etiz |
138 | r-esc-fid |
139 | r-safe-zone |
140 | r-vf |
141 | r-vf-bs-incompat |
142 | r-pers-pid-on-lport |
143 | r-pers-pid-portaddr-collision |
144 | r-pers-pid-port-on-same-area |
145 | r-pers-pid-port-addr-bnd |
146 | r-msfr |
147 | r-sw-halfbw-lic |
148 | r-1g-mode-incompat |
149 | r-10g-mode-incompat |
150 | r-dual-mode-incompat |
151 | r-implict-plt-service-block |
152 | r-port-st-th-exceeded |
153 | r-port-c3txto-th-exceeded |
154 | r-eport-not-supported-def-sw |
155 | r-eport-ll-th-exceeded |
156 | r-eport-synl-th-exceeded |
157 | r-eport-pe-th-exceeded |
158 | r-eport-inw-th-exceeded |
159 | r-eport-crc-th-exceeded |
160 | r-eport-lr-th-exceeded |
161 | r-eport-st-th-exceeded |
162 | r-eport-c3txto-th-exceeded |
163 | r-fopport-ll-th-exceeded |
164 | r-fopport-synl-th-exceeded |
165 | r-fopport-pe-th-exceeded |
166 | r-fopport-inw-th-exceeded |
167 | r-fopport-crc-th-exceeded |
168 | r-fopport-lr-th-exceeded |
169 | r-fopport-st-th-exceeded |
170 | r-fopport-c3txto-th-exceeded |
171 | r-fcuport-ll-th-exceeded |
172 | r-fcuport-synl-th-exceeded |
173 | r-fcuport-pe-th-exceeded |
174 | r-fcuport-inw-th-exceeded |
175 | r-fcuport-crc-th-exceeded |
176 | r-fcuport-lr-th-exceeded |
177 | r-fcuport-st-th-exceeded |
178 | r-fcuport-c3txto-th-exceeded |
179 | r-port-no-area-avail-pers-disable |
180 | r-eport-locked |
181 | r-enh-tizone |
182 | r-sw-port-swap-not-supported |
183 | r-fport-slow-drain-condition |
184 | r-esc-vlanid |
185 | r-port-recov-state |
186 | r-port-auto-disable-losn |
187 | r-port-auto-disable-losg |
188 | r-port-auto-disable-ols |
189 | r-port-auto-disable-nos |
190 | r-port-auto-disable-lip |
191 | r-port-compression |
192 | r-port-encryption |
193 | r-port-enccomp-res |
194 | r-port-decommissioned |
195 | r-port-dportmode |
196 | r-port-dport-incompat |
197 | r-port-enc-comp-mismatch |
198 | r-non-rcs-rem-dom |
199 | r-port-fips-comp-mismatch |
200 | r-port-non-fips-comp-mismatch |
201 | r-port-enc-auth-disabled |
202 | r-port-disable-on-zeroize |
203 | r-cfgspeed-not-supported |
204 | r-fcr-ex-port-not-allowed |
205 | r-port-duplicate-pwwn |
206 | r-fcr-trunk-master-sfid-not-set |
207 | r-nportistrunkmem |
208 | r-policynotsupported |
209 | r-no-icl-license |
210 | r-no-ten-gig-license |
211 | r-fdd-strict-scc-conflict |
212 | r-fdd-strict-dcc-conflict |
213 | r-fdd-strict-fcs-conflict |
214 | r-fdd-strict-fabwide-conflict |
215 | r-fdd-strict-pwd-conflict |
216 | r-fcr-interop-conf |
217 | r-port-enc-interop-conflict |
218 | r-port-comp-interop-conflict |
219 | r-no-port-open-rsp |
220 | r-no-eicl-license |
221 | r-eicl-license-limited |
222 | r-esc-base-sw |
223 | r-sw-cpu-overload |
224 | r-no-icl-pod2-license |
225 | r-port-area-mismatch-pers-disable |
226 | r-unauthorized-device |
227 | r-max-flogi-reached |
228 | r-auth-not-supported-in-switch |
229 | r-icl-ex-on-non-vf |
230 | r-user-disabled-reason |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| swFCPortIndex This object identifies the switch port index.
Note that the value of a port index is 1 higher than the
port number labeled on the front panel.
E.g. port index 1 correspond to port… | column | Brocade-TCSwPortIndex | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1 |
| swFCPortTxWords This object counts the number of Fibre Channel
words that the port has transmitted. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11 |
| swFCPortRxWords This object counts the number of Fibre Channel
words that the port has received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12 |
| swFCPortTxFrames This object counts the number of (Fibre Channel)
frames that the port has transmitted. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.13 |
| swFCPortRxFrames This object counts the number of (Fibre Channel)
frames that the port has received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.14 |
| swFCPortRxC2Frames This object counts the number of Class 2
frames that the port has received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.15 |
| swFCPortRxC3Frames This object counts the number of Class 3
frames that the port has received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.16 |
| swFCPortRxLCs This object counts the number of Link Control
frames that the port has received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.17 |
| swFCPortRxMcasts This object counts the number of Multicast
frames that the port has received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.18 |
| swFCPortTooManyRdys This object counts the number of times when RDYs
exceeds the frames received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.19 |
| swFCPortType This object identifies the type of switch port.
It may be of type stitch(1), flannel(2), loom(3) , bloom(4),rdbloom(5) or wormhole(6). | column | Enumeration | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.2 |
| swFCPortNoTxCredits This object counts the number of times when the
transmit credit has reached zero. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.20 |
| swFCPortRxEncInFrs This object counts the number of encoding error or
disparity error inside frames received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.21 |
| swFCPortRxCrcs This object counts the number of CRC errors
detected for frames received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.22 |
| swFCPortRxTruncs This object counts the number of truncated
frames that the port has received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.23 |
| swFCPortRxTooLongs This object counts the number of received frames that
are too long. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.24 |
| swFCPortRxBadEofs This object counts the number of received frames that
have bad EOF delimiter. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.25 |
| swFCPortRxEncOutFrs This object counts the number of encoding error or
disparity error outside frames received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.26 |
| swFCPortRxBadOs This object counts the number of invalid Ordered
Sets received. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.27 |
| swFCPortC3Discards This object counts the number of Class 3
frames that the port has discarded. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.28 |
| swFCPortMcastTimedOuts This object counts the number of Multicast
frames that has been timed out. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.29 |
| swFCPortPhyState This object identifies the physical state of
the port:
noCard(1) no card present in this switch slot;
noTransceiver(2) no Transceiver module in this port.
noGbic(2) was us… | column | Enumeration | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3 |
| swFCPortTxMcasts This object counts the number of Multicast
frames that has been transmitted. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.30 |
| swFCPortLipIns This object counts the number of Loop Initializations
that has been initiated by loop devices attached. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.31 |
| swFCPortLipOuts This object counts the number of Loop Initializations
that has been initiated by the port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.32 |
| swFCPortLipLastAlpa This object indicates the Physical Address (AL_PA)
of the loop device that initiated the last
Loop Initialization. | column | OctetString | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.33 |
| swFCPortWwn The World_wide_Name of the Fibre Channel port.
The contents of an instance are in the IEEE extended format
as specified in FC-PH; the 12-bit port identifier represents
the port nu… | column | OctetString | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34 |
| swFCPortSpeed obsolete The desired baud rate for the port. It can have the
values of 1GB (1), 2GB (2), Auto-Negotiate (3), 4GB (4), 8GB (5),
10GB (6), 16GB (8). Some of the above values may not be suppo… | column | Enumeration | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.35 |
| swFCPortName A string indicates the name of the addressed port.
The names should be persistent across switch reboots.
Port names do not have to be unique within a switch or
within a fabric. | column | OctetString | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36 |
| swFCPortSpecifier This string indicates the physical port number of the addressed port.
The format of the string is: <slot>/port, where 'slot' being
present only for bladed systems. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.37 |
| swFCPortFlag A bit map of port status flags which includes the information of port type.
Currently this will indicate if the port is virtual or physical. | column | FcPortFlag | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38 |
| swFCPortBrcdType The Brocade port type. | column | Enumeration | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.39 |
| swFCPortOpStatus This object identifies the operational status of
the port. The online(1) state indicates that user frames
can be passed. The unknown(0) state indicates that likely
the port module… | column | Enumeration | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4 |
| swFCPortAdmStatus The desired state of the port. A management station
may place the port in a desired state by setting this
object accordingly. The testing(3) state indicates that
no user frames c… | column | Enumeration | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5 |
| swFCPortLinkState This object indicates the link state of the port.
The value may be:
enabled(1) - port is allowed to participate in the FC-PH
protocol with its attached port (or ports if it is
… | column | Enumeration | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.6 |
| swFCPortTxType This object indicates the media transmitter type of
the port. The value may be:
unknown(1) cannot determined to the port driver
lw(2) long wave laser
sw(3) short wave l… | column | Enumeration | .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.7 |