fsPimGlobalDebug
SUPERMICRO-PIM-MIB ·
.1.3.6.1.4.1.10876.101.1.20.1.1.10
Object
scalar
r/w
Integer32
This is used to enable Debug statements in PIM. A Four byte integer value is specified for enabling the level of debugging. Each bit in the four byte integer variable represents a level of debugging. The combination of levels are also allowed. The user have to enter the corresponding integer value for the bit set.
Context
- MIB
- SUPERMICRO-PIM-MIB
- OID
.1.3.6.1.4.1.10876.101.1.20.1.1.10- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- futurePimScalars
- Siblings
- 13
Syntax
Integer32
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsPimVersionString The version number of the PIM protocol in the router | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.10876.101.1.20.1.1.1 |
| fsPimPmbrStatus The border bit which identifies the router as a border router | scalar | Enumeration | .1.3.6.1.4.1.10876.101.1.20.1.1.11 |
| fsPimRouterMode The Mode of the Pim-SM router (ssm_only or sm_ssm ) | scalar | Enumeration | .1.3.6.1.4.1.10876.101.1.20.1.1.12 |
| fsPimStaticRpEnabled The flag which indicating that static configuration of RP is
available | scalar | Enumeration | .1.3.6.1.4.1.10876.101.1.20.1.1.13 |
| fsPimStatus The enabled status of Multicast Routing by PIM on this router. | scalar | Enumeration | .1.3.6.1.4.1.10876.101.1.20.1.1.14 |
| fsPimSPTGroupThreshold The threshold of data rate for any group when exceeded,
source specific counters are initiated for that particular group
It is based on number of bits per sec.
To initiate SPT swi… | scalar | Integer32 | .1.3.6.1.4.1.10876.101.1.20.1.1.2 |
| fsPimSPTSourceThreshold The threshold of data rate for any source when exceeded,
switching to Shortest Path Tree is initiated.
It is based on number of bits per sec.
To switch to SPT, this threshold MUS… | scalar | Integer32 | .1.3.6.1.4.1.10876.101.1.20.1.1.3 |
| fsPimSPTSwitchingPeriod The period (in seconds)over which the data rate
is to be monitored for intiating source specific
counting or initiating switch to shortest path tree.
Same period is used for m… | scalar | Integer32 | .1.3.6.1.4.1.10876.101.1.20.1.1.4 |
| fsPimSPTRpThreshold The threshold at which the RP initiates switching to
Source specific shortest path.It is based on number
of registered packets received.
To switch to SPT, this threshold MUST be c… | scalar | Integer32 | .1.3.6.1.4.1.10876.101.1.20.1.1.5 |
| fsPimSPTRpSwitchingPeriod The period (in seconds) over which RP monitors
register packets for switching to the source specific
shortest path tree.
To switch to SPT, this period MUST be configured | scalar | Integer32 | .1.3.6.1.4.1.10876.101.1.20.1.1.6 |
| fsPimRegStopRateLimitingPeriod The period (in seconds) over which RP monitors number of
register packets after sending the register stop message
to the source of the register message for rate limiting the
sendi… | scalar | Integer32 | .1.3.6.1.4.1.10876.101.1.20.1.1.7 |
| fsPimMemoryAllocFailCount This counter holds the number of memory allocation failures | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.10876.101.1.20.1.1.8 |
| fsPimGlobalTrace This is used to enable Trace Statements in PIM Module.
A four byte integer value is specified for enabling the level
of tracing.Each Bit in the four byte integer variable represen… | scalar | Integer32 | .1.3.6.1.4.1.10876.101.1.20.1.1.9 |