saCmForceDualscan
SA-CM-MIB ·
.1.3.6.1.4.1.1429.77.1.4.14
Object
scalar
r/w
Enumeration
The MIB will choose whether to force dualscan
operation for the device. Dualscan refers to the
CM ability to automatically scan for both 6MHz and
8MHz carriers.
0 : Will not force dualscan. In this case, the
factory configuration for dualscan will take
effect.
*note: Factory Dualscan configuration is
typically only enabled for EPC products.
1 : Will force dualscan to be enabled. In this
case, dualscan will be enabled regardless of
the factory setting.
This MIB value will be stored to NonVolatile
memory(NVM) and will persist across reboots. If
the MIB is set via the config file, the CM will
store the new setting and begin using it on next
reboot. Removing the setting from the config
file will not change the value stored in NVM the
CM will continue to operate using the previously
stored value.
However, if an SNMP SET is used to modify the
value, then the CM will not use the new setting
until the next reboot occurs or is commanded.
A factory reset of the CM will set the stored
value back to 0.
2 : *Docsis1 mode will only allow the modem to lock Annex B (6MHz) channels and will ignore all Annex A (8MHz) channels.
3 : *EuroDocsis mode will only allow the modem to lock Annex A (8MHz) channesl and will ignore all Annex B (6 MHz)channels.
*Feature available upon request for dualscan capable modems.
Context
- MIB
- SA-CM-MIB
- OID
.1.3.6.1.4.1.1429.77.1.4.14- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- cmInterfaceInfo
- Siblings
- 18
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | useFactorySetting |
1 | enable |
2 | docsis1 |
3 | euroDocsis |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| saCmAutoResetNoActivity Setting this object to any value N > 0 will cause the CM to reboot autonomously
3/4th of N minutes after the modem has detected that there is no connectivity to the CM gateway aft… | scalar | minutes Integer32 | .1.3.6.1.4.1.1429.77.1.4.10 |
| saCmCpeMacAging Setting this object to any value N > 0 will cause the CM to remove a MAC address
from its CPE table N seconds after the modem has detected no traffic from it.
This feature applies… | scalar | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1429.77.1.4.11 |
| saCmBpiForward This object controls whether to forward traffic that is not
destined for any CPE (not in CPE table) when running BPI.
1: follow DOCSIS rules. Do not forward traffic when destinati… | scalar | Enumeration | .1.3.6.1.4.1.1429.77.1.4.12 |
| saCmDsBonding The MIB will choose whether to enable downstream
channel bonding for bonding-capable modems.
Non-bonding modems will ignore this MIB object.
0 : Disable downstream channel bond… | scalar | Enumeration | .1.3.6.1.4.1.1429.77.1.4.15 |
| saCmDocsisCapableVersion Displays the string value for CM DHCP DISCOVER option 60 text.
This mib is only readable through SNMP.This MIB object can queried to identify the device's docsis version that it … | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.1429.77.1.4.33 |
| saOorDsidOverride This MIB is only valid on DOCSIS 3.0 capable modems.
This feature is disabled by default.
This MIB will modify the handling of OOR (Out of Range) DSID packets.
If disabled the mo… | scalar | Enumeration | .1.3.6.1.4.1.1429.77.1.4.34 |
| saCmCpeL2VpnMacAging This MIB defines same functionality as TLV 65 for L2VPN implementation. When the value is
is set to 1 (Enable), Mac aging implementation is as per cablelabs specification. This MI… | scalar | Enumeration | .1.3.6.1.4.1.1429.77.1.4.39 |
| saCmL2VpnUsForwardingCriteria Applicable to L2VPN enabled CMs only. This MIB defines the policy that the CM should use
when forwarding packets that do not match the upstream classifier criteria.
fo… | scalar | Enumeration | .1.3.6.1.4.1.1429.77.1.4.40 |
| cmEthernetOperTable Table for Ethernet interface link speed, duplex, mode, and operation. | table | - | .1.3.6.1.4.1.1429.77.1.4.41 |
| cmEthernetIfAdminOverride For RG Mode enabling this MIB forces the index values of cmEthernetifAdminStatus.x
stored in non-vol into ifAdminStatus.x
For Bridge Mode the ports are exclusively controlled by … | scalar | Enumeration | .1.3.6.1.4.1.1429.77.1.4.42 |
| saCmUsBonding The MIB will choose whether to advertise upstream
channel bonding for bonding-capable modems in the modem
capabilitiies during registration.
Non-DOCSIS 3.0 modems will not have… | scalar | Enumeration | .1.3.6.1.4.1.1429.77.1.4.43 |
| saCmIcmpRateLimit Setting ICMP rate-limit defines the number of ICMP packets
that can be processed per second. Limitation of this number
prevents denial-of-service attacks. Setting the value to 0
… | scalar | packets-per-second Integer32 | .1.3.6.1.4.1.1429.77.1.4.44 |
| saCmTftpBlockSizeV4 This MIB controls the TFTP block size in IPv4 operation. Valid values are 0, 8-8192. A value
of 0 means to use the default block size of 1448 and do not negotiate block size. Any… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1429.77.1.4.46 |
| saCmTftpBlockSizeV6 This MIB controls the TFTP block size in IPv4 operation. Valid values are 0, 8-8192. A value
of 0 means to use the default block size of 1428 and do not negotiate block size. Any… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1429.77.1.4.47 |
| saCmUsPowerLimit This MIB controls the upstream power limit imposed on the cable modem (in dB). | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1429.77.1.4.48 |
| cmConsoleMode To Control console port is disabled, read only, or read write | scalar | Enumeration | .1.3.6.1.4.1.1429.77.1.4.7 |
| cmTimerT4 T4 timeout definition. | scalar | seconds Integer32 | .1.3.6.1.4.1.1429.77.1.4.8 |
| saCmTodRenewal Defines how often to update time with ToD protocol.
0: never
1: together with DHCP renewal
2-11: reserved
12+: number of hours | scalar | hours SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1429.77.1.4.9 |