saCmDsBonding

SA-CM-MIB · .1.3.6.1.4.1.1429.77.1.4.15

Object

scalar r/w Enumeration

The MIB will choose whether to enable downstream 
channel bonding for bonding-capable modems.  
Non-bonding modems will ignore this MIB object.
0 : Disable downstream channel bonding. 
1 : Enable downstream channel bonding
			with all available RCP-IDs standard and proprietary. 
	 2 : Enable downstream bonding but only advertise
			standard RCP-IDs with 2 DS channels.
	 3 : Enable downstream bonding but only advertise
			standard RCP-IDs with 3 or fewer DS channels.
	 4 : Enable downstream bonding but only advertise
			standard RCP-IDs with 4 or fewer DS channels.
	 5 : Not currently applicable (same as 1)
	 6 : Not currently applicable (same as 1)
	 7 : Not currently applicable (same as 1)
	 8 : Enable downstream bonding but only advertise
			standard RCP-IDs with 8 or fewer DS channels.
This MIB will take effect at the next reboot.
This MIB value will be stored to NonVolatile
memory(NVM) and will persist across reboots.  If 
the MIB is set via the config file, the CM will 
store the new setting and reboot if a change is 
necessary.  Removing the setting from the config 
file will not change the value stored in NVM:  the 
CM will continue to operate using the previously 
stored value.
If an SNMP SET is used to modify the value, then 
the CM will not use the new setting until the next 
reboot occurs or is commanded.
A factory reset of the CM will set the stored
value back to 1.

Context

MIB: SA-CM-MIB
OID: .1.3.6.1.4.1.1429.77.1.4.15
Type: scalar
Access: readwrite
Status: current
Parent: cmInterfaceInfo
Siblings: 18

Syntax

Enumeration

Values & Constraints

Enumerated Values

`0`	disable
`1`	enable
`2`	enable2DS
`3`	enable3DS
`4`	enable4DS
`5`	enable5DS
`6`	enable6DS
`7`	enable7DS
`8`	enable8DS

Related Objects

Sibling Objects

Object	Type	Syntax	OID
saCmAutoResetNoActivity Setting this object to any value N > 0 will cause the CM to reboot autonomously 3/4th of N minutes after the modem has detected that there is no connectivity to the CM gateway aft…	scalar	minutes Integer32	`.1.3.6.1.4.1.1429.77.1.4.10`
saCmCpeMacAging Setting this object to any value N > 0 will cause the CM to remove a MAC address from its CPE table N seconds after the modem has detected no traffic from it. This feature applies…	scalar	seconds SNMPv2-SMIInteger32	`.1.3.6.1.4.1.1429.77.1.4.11`
saCmBpiForward This object controls whether to forward traffic that is not destined for any CPE (not in CPE table) when running BPI. 1: follow DOCSIS rules. Do not forward traffic when destinati…	scalar	Enumeration	`.1.3.6.1.4.1.1429.77.1.4.12`
saCmForceDualscan The MIB will choose whether to force dualscan operation for the device. Dualscan refers to the CM ability to automatically scan for both 6MHz and 8MHz carriers. 0 : Will not forc…	scalar	Enumeration	`.1.3.6.1.4.1.1429.77.1.4.14`
saCmDocsisCapableVersion Displays the string value for CM DHCP DISCOVER option 60 text. This mib is only readable through SNMP.This MIB object can queried to identify the device's docsis version that it …	scalar	SNMP-FRAMEWORK-MIBSnmpAdminString	`.1.3.6.1.4.1.1429.77.1.4.33`
saOorDsidOverride This MIB is only valid on DOCSIS 3.0 capable modems. This feature is disabled by default. This MIB will modify the handling of OOR (Out of Range) DSID packets. If disabled the mo…	scalar	Enumeration	`.1.3.6.1.4.1.1429.77.1.4.34`
saCmCpeL2VpnMacAging This MIB defines same functionality as TLV 65 for L2VPN implementation. When the value is is set to 1 (Enable), Mac aging implementation is as per cablelabs specification. This MI…	scalar	Enumeration	`.1.3.6.1.4.1.1429.77.1.4.39`
saCmL2VpnUsForwardingCriteria Applicable to L2VPN enabled CMs only. This MIB defines the policy that the CM should use when forwarding packets that do not match the upstream classifier criteria. fo…	scalar	Enumeration	`.1.3.6.1.4.1.1429.77.1.4.40`
cmEthernetOperTable Table for Ethernet interface link speed, duplex, mode, and operation.	table	-	`.1.3.6.1.4.1.1429.77.1.4.41`
cmEthernetIfAdminOverride For RG Mode enabling this MIB forces the index values of cmEthernetifAdminStatus.x stored in non-vol into ifAdminStatus.x For Bridge Mode the ports are exclusively controlled by …	scalar	Enumeration	`.1.3.6.1.4.1.1429.77.1.4.42`
saCmUsBonding The MIB will choose whether to advertise upstream channel bonding for bonding-capable modems in the modem capabilitiies during registration. Non-DOCSIS 3.0 modems will not have…	scalar	Enumeration	`.1.3.6.1.4.1.1429.77.1.4.43`
saCmIcmpRateLimit Setting ICMP rate-limit defines the number of ICMP packets that can be processed per second. Limitation of this number prevents denial-of-service attacks. Setting the value to 0 …	scalar	packets-per-second Integer32	`.1.3.6.1.4.1.1429.77.1.4.44`
saCmTftpBlockSizeV4 This MIB controls the TFTP block size in IPv4 operation. Valid values are 0, 8-8192. A value of 0 means to use the default block size of 1448 and do not negotiate block size. Any…	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.1429.77.1.4.46`
saCmTftpBlockSizeV6 This MIB controls the TFTP block size in IPv4 operation. Valid values are 0, 8-8192. A value of 0 means to use the default block size of 1428 and do not negotiate block size. Any…	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.1429.77.1.4.47`
saCmUsPowerLimit This MIB controls the upstream power limit imposed on the cable modem (in dB).	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.1429.77.1.4.48`
cmConsoleMode To Control console port is disabled, read only, or read write	scalar	Enumeration	`.1.3.6.1.4.1.1429.77.1.4.7`
cmTimerT4 T4 timeout definition.	scalar	seconds Integer32	`.1.3.6.1.4.1.1429.77.1.4.8`
saCmTodRenewal Defines how often to update time with ToD protocol. 0: never 1: together with DHCP renewal 2-11: reserved 12+: number of hours	scalar	hours SNMPv2-SMIInteger32	`.1.3.6.1.4.1.1429.77.1.4.9`