ruckusAuthDefaultV6IngressAcl
RUCKUS-AUTH-MIB ·
.1.3.6.1.4.1.1991.1.1.3.44.1.1.19
Object
scalar
SNMPv2-TCDisplayString
Specifies the default User Access List (ACL) applied in the Ingress direction for the IPv6 traffic for sessins when ACLs are not dynamically assigned through RADIUS.
Context
- MIB
- RUCKUS-AUTH-MIB
- OID
.1.3.6.1.4.1.1991.1.1.3.44.1.1.19- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- ruckusAuthConfig
- Siblings
- 19
Values & Constraints
Type Constraints
range: 0..255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ruckusAuthDefaultVlan This default VLAN is used to place all the FlexAuth
enabled ports, so this VLAN acts as a VLAN for the
clients to belong to, when authentication server
doesn't assign any VLANs… | scalar | VlanId | .1.3.6.1.4.1.1991.1.1.3.44.1.1.1 |
| ruckusAuthTimeoutAction Specifies the action to be taken, when the
authentication server times out. | scalar | RuckusAuthTimeoutAction | .1.3.6.1.4.1.1991.1.1.3.44.1.1.10 |
| ruckusAuthReauthEnable The reauthentication control for all the FlexAuth
enabled ports. Setting this object to 'enabled'
causes every FlexAuth enabled port to reauthenticate
the devices connecting to th… | scalar | P-BRIDGE-MIBEnabledStatus | .1.3.6.1.4.1.1991.1.1.3.44.1.1.11 |
| ruckusAuthReauthPeriod How often to re-authenticates clients, when periodic
re-authentication is enabled. | scalar | seconds Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.44.1.1.12 |
| ruckusAuthReauthTimeout How often to re-authenticates clients, when the
clients were allowed due to authentication server
timeout. Value of 0 disables the re-authentication. | scalar | seconds Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.44.1.1.13 |
| ruckusAuthIdleTimeout Specifies the time to keep the sessions in the
Ruckus device, after the inactivity detection time
expired in the hardware. If the clients start the
traffic in this time, they nee… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.44.1.1.14 |
| ruckusAuthDeniedTimeout Specifies the time to keep the denied sessions in
the Ruckus device for the clients which are blocked
as they failed authentication. When the clients
start the traffic again, the… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.44.1.1.15 |
| ruckusAuthAging Specifies, if denied and permitted sessions are
enabled or disabled for aging. Aging is enabled by
default. | scalar | RuckusAuthAging | .1.3.6.1.4.1.1991.1.1.3.44.1.1.16 |
| ruckusAuthDefaultV4IngressAcl Specifies the default User Access List (ACL) applied in the
Ingress direction for the IPv4 traffic for sessins when ACLs
are not dynamically assigned through RADIUS. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.1991.1.1.3.44.1.1.17 |
| ruckusAuthDefaultV4EgressAcl Specifies the default User Access List (ACL) applied in the
Egress direction for the IPv4 traffic for sessins when ACLs
are not dynamically assigned through RADIUS. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.1991.1.1.3.44.1.1.18 |
| ruckusAuthVoiceVlan This voice VLAN is used to advertise through
LLDP/CDP on the ports, when connected devices are
detected as Phones and authentication server doesn't
assign any Voice VLAN.
… | scalar | VlanId | .1.3.6.1.4.1.1991.1.1.3.44.1.1.2 |
| ruckusAuthDefaultV6EgressAcl Specifies the default User Access List (ACL) applied in the
Egress direction for the IPv6 traffic for sessins when ACLs
are not dynamically assigned through RADIUS. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.1991.1.1.3.44.1.1.20 |
| ruckusAuthCriticalVlan This VLAN is used to place the clients, when the
authentication server times out and the timeout
action is configired as 'critical', so the clients
have limited access.
… | scalar | VlanId | .1.3.6.1.4.1.1991.1.1.3.44.1.1.3 |
| ruckusAuthRestrictVlan This VLAN is used to place the clients, when the
clients fail the authentication and the failure
action is configured as 'restrict', so the clients
have limited access.
… | scalar | VlanId | .1.3.6.1.4.1.1991.1.1.3.44.1.1.4 |
| ruckusAuthEnable Specifies, which authentication methods are enabled
globally. Unless the method is enabled globally, the
same can't be enabled at port level. A bit field of
'1' indicates enabled,… | scalar | Bits | .1.3.6.1.4.1.1991.1.1.3.44.1.1.5 |
| ruckusAuthMode Specifies the authentication mode for all the
FlexAuth enabled ports. | scalar | RuckusAuthMode | .1.3.6.1.4.1.1991.1.1.3.44.1.1.6 |
| ruckusAuthMethods Specifies which authentication methods to be
attempted in series of methods for all FlexAuth
enabled ports. | scalar | RuckusAuthOrder | .1.3.6.1.4.1.1991.1.1.3.44.1.1.7 |
| ruckusAuthMaxSessions Specifies the maximum number of authenticated
clients allowed on a port. This doesn't include the
clients allowed due to authentication failure and
timeout policies. | scalar | Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.44.1.1.8 |
| ruckusAuthFailAction Specifies the action to be taken, when the clients
fail the authentication. | scalar | RuckusAuthFailAction | .1.3.6.1.4.1.1991.1.1.3.44.1.1.9 |