dsx1SendCode
RFC1406-MIB ·
.1.3.6.1.2.1.10.18.6.1.7
Object
column
mandatory
r/w
Enumeration
This variable indicates what type of code is
being sent across the DS1 interface by the dev-
ice. The values mean:
dsx1SendNoCode
sending looped or normal data
dsx1SendLineCode
sending a request for a line loopback
dsx1SendPayloadCode
sending a request for a payload loopback
dsx1SendResetCode
sending a loopback termination request
dsx1SendQRS
sending a Quasi-Random Signal (QRS) test
pattern
dsx1Send511Pattern
sending a 511 bit fixed test pattern
dsx1Send3in24Pattern
sending a fixed test pattern of 3 bits set
in 24
dsx1SendOtherTestPattern
sending a test pattern other than those
described by this object
Context
- MIB
- RFC1406-MIB
- OID
.1.3.6.1.2.1.10.18.6.1.7- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- dsx1ConfigEntry
- Table
- dsx1ConfigTable
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | dsx1SendNoCode |
2 | dsx1SendLineCode |
3 | dsx1SendPayloadCode |
4 | dsx1SendResetCode |
5 | dsx1SendQRS |
6 | dsx1Send511Pattern |
7 | dsx1Send3in24Pattern |
8 | dsx1SendOtherTestPattern |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dsx1LineIndex mandatory This object is the identifier of a DS1 Inter-
face on a managed device. If there is an ifEn-
try that is directly associated with this and
only this DS1 interface, it shou… | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.1 |
| dsx1LineStatus mandatory This variable indicates the Line Status of the
interface. It contains loopback, failure, re-
ceived 'alarm' and transmitted 'alarm' infor-
mation.
The dsx1LineS… | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.10 |
| dsx1SignalMode mandatory 'none' indicates that no bits are reserved for
signaling on this channel.
'robbedBit' indicates that T1 Robbed Bit Sig-
naling is in use.
'bitOrie… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.11 |
| dsx1TransmitClockSource mandatory The source of Transmit Clock.
'loopTiming' indicates that the recovered re-
ceive clock is used as the transmit clock.
'localTiming' indicates that… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.12 |
| dsx1Fdl mandatory This bitmap describes the use of the facili-
ties data link, and is the sum of the capabili-
ties:
'other' indicates that a protocol other than
one following i… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.13 |
| dsx1IfIndex mandatory This value for this object is equal to the
value of ifIndex from the Interfaces table of
MIB II (RFC 1213). | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.2 |
| dsx1TimeElapsed mandatory The number of seconds that have elapsed since
the beginning of the current error-measurement
period. | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.3 |
| dsx1ValidIntervals mandatory The number of previous intervals for which
valid data was collected. The value will be 96
unless the interface was brought on-line within
the last 24 hours, in which case the… | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.4 |
| dsx1LineType mandatory This variable indicates the variety of DS1
Line implementing this circuit. The type of
circuit affects the number of bits per second
that the circuit can reasonably car… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.5 |
| dsx1LineCoding mandatory This variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.
dsx1JBZS refers the Jam… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.6 |
| dsx1CircuitIdentifier mandatory This variable contains the transmission
vendor's circuit identifier, for the purpose of
facilitating troubleshooting. | column | OctetString | .1.3.6.1.2.1.10.18.6.1.8 |
| dsx1LoopbackConfig mandatory This variable represents the loopback confi-
guration of the DS1 interface. Agents support-
ing read/write access should return badValue in
response to a requested loopback sta… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.9 |