dsx1LoopbackConfig
RFC1406-MIB ·
.1.3.6.1.2.1.10.18.6.1.9
Object
column
mandatory
r/w
Enumeration
This variable represents the loopback confi-
guration of the DS1 interface. Agents support-
ing read/write access should return badValue in
response to a requested loopback state that the
interface does not support. The values mean:
dsx1NoLoop
Not in the loopback state. A device that
is not capable of performing a loopback on
the interface shall always return this as
it's value.
dsx1PayloadLoop
The received signal at this interface is
looped through the device. Typically the
received signal is looped back for re-
transmission after it has passed through
the device's framing function.
dsx1LineLoop
The received signal at this interface does
not go through the device (minimum pene-
tration) but is looped back out.
dsx1OtherLoop
Loopbacks that are not defined here.
Context
- MIB
- RFC1406-MIB
- OID
.1.3.6.1.2.1.10.18.6.1.9- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- dsx1ConfigEntry
- Table
- dsx1ConfigTable
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | dsx1NoLoop |
2 | dsx1PayloadLoop |
3 | dsx1LineLoop |
4 | dsx1OtherLoop |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dsx1LineIndex mandatory This object is the identifier of a DS1 Inter-
face on a managed device. If there is an ifEn-
try that is directly associated with this and
only this DS1 interface, it shou… | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.1 |
| dsx1LineStatus mandatory This variable indicates the Line Status of the
interface. It contains loopback, failure, re-
ceived 'alarm' and transmitted 'alarm' infor-
mation.
The dsx1LineS… | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.10 |
| dsx1SignalMode mandatory 'none' indicates that no bits are reserved for
signaling on this channel.
'robbedBit' indicates that T1 Robbed Bit Sig-
naling is in use.
'bitOrie… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.11 |
| dsx1TransmitClockSource mandatory The source of Transmit Clock.
'loopTiming' indicates that the recovered re-
ceive clock is used as the transmit clock.
'localTiming' indicates that… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.12 |
| dsx1Fdl mandatory This bitmap describes the use of the facili-
ties data link, and is the sum of the capabili-
ties:
'other' indicates that a protocol other than
one following i… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.13 |
| dsx1IfIndex mandatory This value for this object is equal to the
value of ifIndex from the Interfaces table of
MIB II (RFC 1213). | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.2 |
| dsx1TimeElapsed mandatory The number of seconds that have elapsed since
the beginning of the current error-measurement
period. | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.3 |
| dsx1ValidIntervals mandatory The number of previous intervals for which
valid data was collected. The value will be 96
unless the interface was brought on-line within
the last 24 hours, in which case the… | column | Integer32 | .1.3.6.1.2.1.10.18.6.1.4 |
| dsx1LineType mandatory This variable indicates the variety of DS1
Line implementing this circuit. The type of
circuit affects the number of bits per second
that the circuit can reasonably car… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.5 |
| dsx1LineCoding mandatory This variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.
dsx1JBZS refers the Jam… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.6 |
| dsx1SendCode mandatory This variable indicates what type of code is
being sent across the DS1 interface by the dev-
ice. The values mean:
dsx1SendNoCode
sending looped or normal d… | column | Enumeration | .1.3.6.1.2.1.10.18.6.1.7 |
| dsx1CircuitIdentifier mandatory This variable contains the transmission
vendor's circuit identifier, for the purpose of
facilitating troubleshooting. | column | OctetString | .1.3.6.1.2.1.10.18.6.1.8 |