rndIfCompressionStatus
RADWARE-MIB ·
.1.3.6.1.4.1.89.4.1.1.9
Object
column
mandatory
Enumeration
Defines the status of the compression component:
not-inserted - Compression component is not in the device
active - Compression is enabled and operates correctly
not-active - Compression is enables but does not operate.
The reason may be that there is no compression
component on the device connected to this interface.
disabled - Compression was disabled by management, using
variable rndCompression.
Context
- MIB
- RADWARE-MIB
- OID
.1.3.6.1.4.1.89.4.1.1.9- Type
- column
- Access
- readonly
- Status
- mandatory
- Parent
- rndIfEntry
- Table
- rndIfTable
- Siblings
- 17
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | not-inserted |
2 | active |
3 | not-active |
4 | disable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| rndIfIndex mandatory Index to the RND Interface Table. The interface defined by a
particular value of this index is the same interface as
identified by the same value of ifIndex (MIBII). | column | Integer32 | .1.3.6.1.4.1.89.4.1.1.1 |
| rndIfCompressionRate mandatory Percentage of compression. This variable applies only
if rndCompressionStatus is active. | column | Integer32 | .1.3.6.1.4.1.89.4.1.1.10 |
| rndIfLATCompression mandatory Enable/Disable the LAT Compression. | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.11 |
| rndIfCompressionType mandatory This parameter indicates the type of compression option available in the device.
none(1) - indicates that there is no compression option in the device
lowSpeed(2) - indicates … | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.12 |
| rndIfFilterMode mandatory This parameter indicates the type of filtering in the device. | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.13 |
| rndIfChannelType mandatory The type of the WAN channel | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.14 |
| rndIfBridge mandatory This variable indicates whether this interface forward Layer II pakages. | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.15 |
| rndHighPriorityIf mandatory This variable indicates whether this interface will forward pakages
that fit HighPriority set by the manager. | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.16 |
| rndWanHeader mandatory This variable indicates the RND WAN header type used for frames
which pass through this interface. 'regular' specifies a 14 bytes
header compatible with older OG versions and 'sho… | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.17 |
| rndDuplexMode mandatory This variable indicates whether this interface operates in half duplex
full duplex or auto negotiation mode. | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.18 |
| rndIfBoardNum mandatory The interface defined by this entry correspTnds to the board
defined by the same value of rndSlotBoardNum in the rndSlotTab. | column | Integer32 | .1.3.6.1.4.1.89.4.1.1.2 |
| rndIfNetAddress mandatory The IP address of the interface defined by the particular value of
rndIfIndex. | column | RFC1155-SMINetworkAddress | .1.3.6.1.4.1.89.4.1.1.3 |
| rndIfStatus mandatory The current status of the interface. | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.4 |
| rndIfClockType mandatory rndIfClockType defines the type of clock each interface
uses: internal or external. | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.5 |
| rndIfBaudRate mandatory Defines the baud rate of use by the interface. The valid
rates are determined by the type of the media for which this
baud rate is defined. | column | Integer32 | .1.3.6.1.4.1.89.4.1.1.6 |
| rndIfCost mandatory This variable assigns a transmission cost to the interface
(channel or LAN). These costs are used in Level II routing. The
costs aretypically inversly proportional to the channel … | column | Integer32 | .1.3.6.1.4.1.89.4.1.1.7 |
| rndIfCompression mandatory Defines whether data compression is enabled or disabled for the
interface. | column | Enumeration | .1.3.6.1.4.1.89.4.1.1.8 |