prtSParamStatus
RAD-Mpmx-MIB ·
.1.3.6.1.4.1.164.3.1.4.1.1.1.15
Object
column
OctetString
This object indicates Status of parameters specific to the
selected port.
- For a port that has no special status or is supported
by prtSExHsfStatTable - 1 Octet: 00hex
- For VC-6, VC-6A, VC-6AG, VC-6A/4LB, VC-12, VC-12/6, external ports - 1 Octet :
Bit 7 (MSB)..Bit 2 = 0 (NA)
Bit 1: Tx Signaling '1'=On ; '0'=Off
Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off
- For VC-2/R2(FXS) external ports - 1 Octet :
Bit - 7 6 5 4 3 2 1 0
|_| |_________|
Call Call State
Direction
Bit 7 (MSB) and Bit 6 : Call Direction
00 - Incoming
01 - Outgoing
Bit 5..Bit 0: Call State
000000 - Idle
000001 - Seized
000010 - Both-Way Conflict
000011 - Seizure Ack
000100 - Answered
000101 - Clear Backward
000110 - Clear Forward
000111 - Blocked
001000 - Fault
001001 - Fault 3
001010 - Fault 4
001011 - Fault 5
001100 - Fault 6
001101 - Fault 7
- For ML-20 external port - 3 Octets :
- 1 MS Octet will represent the Real Rate used:
Bit - 7 6 5 4 3 2 1 0
|___| |_______|
spare Rate
Valid values: 0..31, meaning 0..31x64Kbps
Invalid values: 32..255.
- 2 LS Octets will represent the Status of 7 Control
Signals:
Signal - --- CTS DSR DCD RJ TM DTR RTS
Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Octet - 2 3 (LS)
'---' will always have the value 00
Rest of the Signals (2 bits each) can have the following
values:
00=NA ; 01=unused ; 10=Off ; 11=On
- For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet
Bit - 7 6 5 4 3 2 1 0
|___________|
spare Mode of Operation
Mode of Operation: '1'=Central ; '0'=Remote
- For ACM external port - 1 Octet
Bit - 7 6 5 4 3 2 1 0
|_________|
spare Alarm State
Alarm State: according to bits 1,0:
00=NA ; 01=unused ; 10=Off ; 11=On
- For HS-U/1 external port - 1 Octet
Bit 7 6 5 4 3 2 1 0 LSB
|________| |__| |__|
spare modem sync
modem: 00 = other sync: 00 = not sync
01 = unknown 01 = sync
10 = ASMi-31/2 10 = reserved
11 = reserved 11 = reserved
- For MTML-2/4 external ports, ML-8 externalports, ML-IP (MTML-IP)
internal ports and MTML-E2 internal ports - 1 Octet :
Bit 7 6 5 4 3 2 1 0 LSB
|
BERT State
BERT State (Bit 0):
0 = OFF (BERT is not running on this port or any of its TSs/Bits)
1 = ON (BERT is running on this port OR on one of its TSs/Bits)
- For ML-20N external ports - 4 Octets
- 1 MS Octet will represent the Actual Link Rate:
Bit - 7 6 5 4 3 2 1 0
|_| |_________|
spare Rate
Valid values: 0..34, meaning:
0..32 = (0..32)x64Kbps
33 = Invalid Rate
34 = not applicable (when Rate is not Auto)
35 = 0 Kbps
Invalid values: 36..255.
- 2 middle Octets will represent the Status of 4 Control
Signals:
- LS Octet - Bits 3-0: RTS/C (Command, for X.21 interface)
Bits 7-4: DCD/I (Indication for X.21 interface)
- MS Octet - Bits 3-0: DTR
Bits 7-4: DSR
Each 4 Bits are divided as follows:
- 2 MS bits: DCE
- 2 LS bits: DTE
For each 2 bits (DCE/DTE):
00=NA ; 01=unused ; 10=Off ; 11=On.
- LS Octet: (as for MTML-2):
Bit 7 6 5 4 3 2 1 0 LSB
|
BERT State
BERT State (Bit 0):
0 = OFF (BERT is not running on this port or any of its TSs/Bits)
1 = ON (BERT is running on this port OR on one of its TSs/Bits)
- For MP-2100/2200 MSL-4/E1, MSL-8/E1 External ports - 3 Octets
- MS octet: far-end modem channel interface
- Middle octet: Material (plastic/metal), far-end modem type,
synchronization with far-end modem
- LS octet: BERT state (at port/TS/Bit level)
- MS octet: 0000 0000 = no interface
0000 0001 = db15 (X21)
0000 0010 = IR-IP
0000 0011 = IR-ETH-Q
0000 0100 = V35
0000 0101 = ETH-RJ45
0000 0110 = G703
0000 0111 = db25 (RS530)
0000 1000 = ETH-BNC
0000 1001 = E1(Balanced)
0000 1010 = E1(Unbalanced)
0000 1011 = IR-ETH-QN
Rest of the combinations: reserved
- Middle octet:
Bit 7 6 5 4 3 2 1 0 LSB
| |___________| |__|
Box material modem sync
Box material modem: 00000 = other sync: 00 = not sync
(for ASMi-52 SA) 00001 = unknown 01 = sync
0=metal 00010 = reserved 10 = reserved
1=plastic 00011 = reserved 11 = reserved
00100 = reserved
00101 = reserved
00110 = ASMi-52 SA/2W/Slave
00111 = ASMi-52 SA/2W/Master
01000 = ASMi-52/CQ card of LRS-24
01001 = ASMi-52/CD card of LRS-24
01010 = D16GSDSL card of DXC-3000
01011 = LRS-52
01100 = FCD-IP
01101 = FCD-IPM
01110 = D8SL card of DXC-30
01111 = ASMi-52A
10000 = MP card (SHDSL)
10001 = ASMi-52L
Rest = reserved
- LS Octet: (as for MTML-2):
Bit 7 6 5 4 3 2 1 0 LSB
|
BERT State
BERT State (Bit 0):
0 = OFF (BERT is not running on this port or any of its TSs)
1 = ON (BERT is running on this port OR on one of its TSs)
- For MP-4100 MSL card Links - 4 Octets
- MS octet: far-end modem DTE2 interface (same as for MP-2100 MSL cards)
- after MS octet: far-end modem DTE1 interface (same as for MP-2100 MSL cards)
- before LS octet: Material (plastic/metal), far-end modem type,
synchronization with far-end modem (same as for MP-2100 MSL cards)
- LS octet: BERT state (at port/TS/Bit level)- same as for MP-2100 MSL cards
- For MP-4100, LRS-102 OP-108/106 , OP-34/25 Links - 3 Octets
- MS octet: Far-End PS type and state
- Middle octet: synchronization with Far-End device
- LS octet: BERT state (at port/TS level) - same as for MP-2100 MSL cards
- MS octet:
Bit 7 6 5 4 3 2 1 0 LSB
|__| |__| |__| |__|
PS-A PS-A PS-B PS-B
PS Type PS State PS Type PS State
00=None 00=None
01=AC-DC 01=OK
10=DC 10=Fail
11=AC
- Middle octet:
Bit 7 6 5 4 3 2 1 0 LSB
|__|
sync:
00 = not sync
01 = sync
10 = reserved
11 = reserved
Rest = reserved
Context
- MIB
- RAD-Mpmx-MIB
- OID
.1.3.6.1.4.1.164.3.1.4.1.1.1.15- Type
- column
- Access
- readonly
- Status
- current
- Parent
- prtSInstEntry
- Table
- prtSInstTable
- Siblings
- 16
Syntax
OctetString
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| prtSInstSltIdx This attribute indicates a unique number to identify the
slot where the card is inserted.
In the ?004 Unit the entries io6(10)..io(16) are not valid.
For the Vmux2100 Main Board c… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.1 |
| prtSTstCmd Setting this attribute to any of the above values will
initiate a test on the specific port if the operation is
legal. If the operation is not legal, the mux will ignore
the opera… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.10 |
| prtSTstDuration This attribute indicates the maximum duration of executing
a test on the specific port. This entry applies to all the
test operations. The resolution will be a minute, and the
max… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.11 |
| prtSBertClrCmd Setting this attribute initiates bert count clear operation.
It is valid only when bert test is active on the specific
port. | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.12 |
| prtSBertTstRslt This attribute indicates the number of Bit Error Rate
indicated during the BERT operation.
It is valid only when bert test is active on the specific
port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.13 |
| prtSInterfaceType This attribute indicates a unique HW interface type of the
selected port. | column | OctetString | .1.3.6.1.4.1.164.3.1.4.1.1.1.14 |
| prtSTestMaskXp This is an Expanded test mask of the prtSTestMask object.
The prtSTestMask object reached its maximum, being an Integer with 32 bits.
This object indicates which tests from the '… | column | OctetString | .1.3.6.1.4.1.164.3.1.4.1.1.1.16 |
| prtSRdnStatus Redundancy Status of this port.
noRdn - this port is not part of a Redundancy pair/group.
offline - this port is offline from Redundancy point of view.
online - this port is onli… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.17 |
| prtSInstPrtIdx This attribute indicates a unique number to identify a port
in a specific card.
The valid ports depend on the installed card:
the valid external ports (interfaces) are (1..mdlCNoO… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.2 |
| prtSInstPrtType This attribute describes the type of the designated port.
In MX 3000 only external & internal options are used.
All the other options are only for MX 30/300 which need special han… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.3 |
| prtSInstIfIndex This attribute indicates the unique interface number
assigned to the port. The specific interface of this
attribute is the same as the interface identified by the
value of ifind… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.4 |
| prtSActiveStatus This attribute describes the activity status of the port.
unknown(1) indicates that the information is not supported.
notUsed(2) indicates that the ch is not connected according
… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.5 |
| prtSAlrStatus Indicates the alarm state in the port(ch) agent level.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
critical alarm,
… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.6 |
| prtSMaskedAlrStat Indicates the alarm state in the port(ch) agent level,
including Masked alarms.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.7 |
| prtSClearAlrCmd Setting this attribute to on(3) enforces a clear operation
of the alarm status events in the given port. The clear
operation will not be applied for masked/inverted alarms. | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.8 |
| prtSTestMask This is a mask which indicates which tests from the
'prtSTstCmd' list are allowed for the requested port.
If a specific test is allowed, its respective bit
will be SET in the mask… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.9 |