exCMConfigEthernetAutoNegotiation
PERLE-MCR-MGT-MIB ·
.1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.30
Object
column
r/w
EnableDisableValue
This object identifies the whether ethernet auto-negotiation is enabled. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
Context
- MIB
- PERLE-MCR-MGT-MIB
- OID
.1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.30- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- exCMConfigEntry
- Table
- exCMConfigTable
- Siblings
- 91
Syntax
EnableDisableValue
- Source
- EnableDisableValue
- Base type
Enumeration
Values & Constraints
Type Values
-1 | notApplicable |
0 | disable |
1 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| exCMConfigVdslRole This object specifies the VDSL role: auto, local (CO), or remote (CPE). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.10 |
| exCMConfigVdslRate This object specifies the VDSL rate/reach. | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.11 |
| exCMConfigVdslSymmetry This object specifies the VDSL band plan or symmetry. | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.12 |
| exCMConfigVdslProfile This object specifies the VDSL profile. | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.13 |
| exCMConfigVdslOverrideProfile This object specifies whether to override advanced VDSL profile
settings (e.g exCMConfigVdslSignalToNoiseRatioUp). | column | EnableDisableValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.14 |
| exCMConfigVdslSignalToNoiseRatioUp This object represents the advanced VDSL profile setting
signal-to-noise ratio (upstream) in 0.1 dB. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.15 |
| exCMConfigVdslMinDataRateUp This object represents the advanced VDSL profile setting
minimum data rate (upstream) in kbps. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.16 |
| exCMConfigVdslMaxDataRateUp This object represents the advanced VDSL profile setting
maximum data rate (upstream) in kbps. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.17 |
| exCMConfigVdslMaxInterleaveDelayUp This object represents the advanced VDSL profile setting
maximum delay (upstream) in ms. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.18 |
| exCMConfigVdslMinInpUp This object represents the advanced VDSL profile setting
minimum INP (impulse noise protection) (upstream). | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.19 |
| exCMConfigSlotIndex The Slot number the ex-CM type module is currently inserted | column | SlotNumber | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.2 |
| exCMConfigVdslSignalToNoiseRatioDown This object represents the advanced VDSL profile setting
signal-to-noise ratio (downstream) in 0.1 dB. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.20 |
| exCMConfigVdslMinDataRateDown This object represents the advanced VDSL profile setting
minimum data rate (downstream) in kbps. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.21 |
| exCMConfigVdslMaxDataRateDown This object represents the advanced VDSL profile setting
maximum data rate (downstream) in kbps. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.22 |
| exCMConfigVdslMaxInterleaveDelayDown This object represents the advanced VDSL profile setting
maximum delay (downstream) in ms. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.23 |
| exCMConfigVdslMinInpDown This object represents the advanced VDSL profile setting
minimum INP (impulse noise protection) (downstream). | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.24 |
| exCMConfigVdslBitswapping This object represents the advanced VDSL profile
setting bitswapping. | column | EnableDisableValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.25 |
| exCMConfigVdslLowBandwidthAlarmUp This object represents the VDSL low bandwidth alarm threshold (upstream) in kbps. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.26 |
| exCMConfigVdslLowBandwidthAlarmDown This object represents the VDSL low bandwidth alarm threshold (downstream) in kbps. | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.27 |
| exCMConfigEthernetPortName This object identifies a user definable name for the ethernet port. | column | OctetString | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.28 |
| exCMConfigEthernetPortEnable This object identifies whether the VDSL port is enabled. | column | YesNoValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.29 |
| exCMConfigStatus When you perform a GET on this variable, one of
the following values will be returned:
1-Indicates that the container folder is active with no changes.
2-Indicates that the contai… | column | ContainerStatus | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.3 |
| exCMConfigEthernetAutoNegAdv10HDX This object controls whether or the ethernet port advertises willingness
to connect at 10Mbps, half duplex. This setting is ignored when
auto-negotiation is disabled. | column | YesNoValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.31 |
| exCMConfigEthernetAutoNegAdv10FDX This object controls whether or the ethernet port advertises willingness
to connect at 10Mbps, full duplex. This setting is ignored when
auto-negotiation is disabled. | column | YesNoValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.32 |
| exCMConfigEthernetAutoNegAdv100HDX This object controls whether or the ethernet port advertises willingness
to connect at 100Mbps, half duplex. This setting is ignored when
auto-negotiation is disabled. | column | YesNoValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.33 |
| exCMConfigEthernetAutoNegAdv100FDX This object controls whether or the ethernet port advertises willingness
to connect at 100Mbps, full duplex. This setting is ignored when
auto-negotiation is disabled. | column | YesNoValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.34 |
| exCMConfigEthernetAutoNegAdv1000FDX This object controls whether or the ethernet port advertises willingness
to connect at 1000Mbps, full duplex. This setting is ignored when
auto-negotiation is disabled. | column | YesNoValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.35 |
| exCMConfigEthernetSpeed If ethernet auto-negotiation is disabled then this object identifies
the configured cooper speed. 1000 Mbps speed can only be auto
negotiated. If ethernet auto-negotiation is enab… | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.36 |
| exCMConfigEthernetDuplex If ethernet auto-negotiation is disabled then this object identifies
the duplex setting for 10 & 100 Mbps for the ethernet port. Duplex for
1000 Mbps has to be auto negotiated. T… | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.37 |
| exCMConfigEthernetCrossOver This object identifies the ethernet MDI/MDI-X setting.This object
is read-only if the media converter module's ConfigMode jumper is set to | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.38 |
| exCMConfigEthernetPauseEnh This object identifies the ethernet pause (flow control) setting that
is a advertised. The settings can be disabled, advertise symmetrical,
advertise asymmetrical TX or advertise … | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.39 |
| exCMConfigModuleName This object identifies a user configurable name for the media converter module
present in the chassis. | column | OctetString | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.4 |
| exCMConfigEthernetAutoSpeedDownshift This object identifies the number of times the PHY attempts to
establish a Gigabit link before the PHY downshift to the next
highest speed. A value of 0 indicates the auto downsh… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.40 |
| exCMConfigEthernet10BaseTDistance When using cable exceeding 100 meters in 10BASE-T mode this feature
should be set to extended(1). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.41 |
| exCMConfigUnidirectionalEthernet Restrict the flow of Ethernet traffic to a single direction.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.42 |
| exCMConfigPriorityToEgressQueueMap0 Set the egress queue of frames tagged with 802.1p priority 0.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This feat… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.43 |
| exCMConfigPriorityToEgressQueueMap1 Set the egress queue of frames tagged with 802.1p priority 1.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This feat… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.44 |
| exCMConfigPriorityToEgressQueueMap2 Set the egress queue of frames tagged with 802.1p priority 2.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This feat… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.45 |
| exCMConfigPriorityToEgressQueueMap3 Set the egress queue of frames tagged with 802.1p priority 3.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This feat… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.46 |
| exCMConfigPriorityToEgressQueueMap4 Set the egress queue of frames tagged with 802.1p priority 4.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This feat… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.47 |
| exCMConfigPriorityToEgressQueueMap5 Set the egress queue of frames tagged with 802.1p priority 5.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This feat… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.48 |
| exCMConfigPriorityToEgressQueueMap6 Set the egress queue of frames tagged with 802.1p priority 6.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This feat… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.49 |
| exCMConfigLinkMode This object identifies the Link Mode for the media converter module. This object
is read-only if the media converter module's ConfigMode jumper is set to
hardwareSwitches(0). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.5 |
| exCMConfigPriorityToEgressQueueMap7 Set the egress queue of frames tagged with 802.1p priority 7.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This feat… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.50 |
| exCMConfigEthernet8021pPriority Use 802.1p tag priority.
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.51 |
| exCMConfigEthernetIpTosPriority Use IP TOS priority.
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.52 |
| exCMConfigEthernetPriorityPrecedence Configure priority precedence.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.53 |
| exCMConfigEthernetCongestionPolicy Configure priority congestion policy.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.54 |
| exCMConfigEthernetPriorityMap0 Change the priority of frames tagged with 802.1p priority 0.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.55 |
| exCMConfigEthernetPriorityMap1 Change the priority of frames tagged with 802.1p priority 1.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.56 |
| exCMConfigEthernetPriorityMap2 Change the priority of frames tagged with 802.1p priority 2.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.57 |
| exCMConfigEthernetPriorityMap3 Change the priority of frames tagged with 802.1p priority 3.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.58 |
| exCMConfigEthernetPriorityMap4 Change the priority of frames tagged with 802.1p priority 4.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.59 |
| exCMConfigInterlinkFaultFeedback This object identifies the interlink fault feedback setting for the media
module.
This object is read-only if the media converter module's ConfigMode
jumper is set to hardwareSwi… | column | EnableDisableValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.6 |
| exCMConfigEthernetPriorityMap5 Change the priority of frames tagged with 802.1p priority 5.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.60 |
| exCMConfigEthernetPriorityMap6 Change the priority of frames tagged with 802.1p priority 6.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.61 |
| exCMConfigEthernetPriorityMap7 Change the priority of frames tagged with 802.1p priority 7.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.62 |
| exCMConfigEthernetIngressLimit Set a limit on the rate of incoming packets.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.63 |
| exCMConfigEthernetEgressLimit Set a limit on the rate of outgoing packets.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.64 |
| exCMConfigEthernetDiscardTaggedFrames Enable discarding of tagged frames.
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.65 |
| exCMConfigEthernetDiscardUntaggedFrames Enable discarding of untagged frames.
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.66 |
| exCMConfigEthernetDefaultVlanId Set the default VLAN ID to insert when tagging frames.
(This feature may require a media converter module firmware upgrade). | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.67 |
| exCMConfigEthernetDefaultPriority Set the default frame priority.
(This feature may require a media converter module firmware upgrade). | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.68 |
| exCMConfigEthernetVlanTaggingAction Set the default tagging action.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.69 |
| exCMConfigVdslPortName This object identifies a user definable name for the VDSL port. | column | OctetString | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.7 |
| exCMConfigEthernetFilterUnknownMulticast Enable filtering of multicast frames with an unknown destination
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.70 |
| exCMConfigEthernetFilterUnknownUnicast Enable filtering of unicast frames with an unknown destination
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.71 |
| exCMConfigVdsl8021pPriority Use 802.1p tag priority.
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.72 |
| exCMConfigVdslIpTosPriority Use IP TOS priority.
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.73 |
| exCMConfigVdslPriorityPrecedence Configure priority precedence.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.74 |
| exCMConfigVdslCongestionPolicy Configure priority congestion policy.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.75 |
| exCMConfigVdslPriorityMap0 Change the priority of frames tagged with 802.1p priority 0.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.76 |
| exCMConfigVdslPriorityMap1 Change the priority of frames tagged with 802.1p priority 1.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.77 |
| exCMConfigVdslPriorityMap2 Change the priority of frames tagged with 802.1p priority 2.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.78 |
| exCMConfigVdslPriorityMap3 Change the priority of frames tagged with 802.1p priority 3.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.79 |
| exCMConfigVdslPortEnable This object identifies whether the VDSL port is enabled. | column | YesNoValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.8 |
| exCMConfigVdslPriorityMap4 Change the priority of frames tagged with 802.1p priority 4.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.80 |
| exCMConfigVdslPriorityMap5 Change the priority of frames tagged with 802.1p priority 5.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.81 |
| exCMConfigVdslPriorityMap6 Change the priority of frames tagged with 802.1p priority 6.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.82 |
| exCMConfigVdslPriorityMap7 Change the priority of frames tagged with 802.1p priority 7.
A value of -1 signifies that this feature is not supported
by the current media converter module firmware.
(This featu… | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.83 |
| exCMConfigVdslIngressLimit Set a limit on the rate of incoming packets.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.84 |
| exCMConfigVdslEgressLimit Set a limit on the rate of outgoing packets.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.85 |
| exCMConfigVdslDiscardTaggedFrames Enable discarding of tagged frames.
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.86 |
| exCMConfigVdslDiscardUntaggedFrames Enable discarding of untagged frames.
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.87 |
| exCMConfigVdslDefaultVlanId Set the default VLAN ID to insert when tagging frames.
(This feature may require a media converter module firmware upgrade). | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.88 |
| exCMConfigVdslDefaultPriority Set the default frame priority.
(This feature may require a media converter module firmware upgrade). | column | Integer32 | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.89 |
| exCMConfigVdslProfileMode This object specifies how the VDSL profile is selected.
Auto: select through exCMConfigVdslRate and exCMConfigVdslSymmetry
Manual: select through exCMConfigVdslProfile. | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.9 |
| exCMConfigVdslVlanTaggingAction Set the default tagging action.
(This feature may require a media converter module firmware upgrade). | column | Enumeration | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.90 |
| exCMConfigVdslFilterUnknownMulticast Enable filtering of multicast frames with an unknown destination
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.91 |
| exCMConfigVdslFilterUnknownUnicast Enable filtering of unicast frames with an unknown destination
(This feature may require a media converter module firmware upgrade). | column | OnOffValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.92 |
| exCMConfigVdslFastMode This object represents the VDSL fast mode setting. | column | EnableDisableValue | .1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.93 |