laststandbyunsuccessfulstart
PACKETFLUX-STANDBYPOWER ·
.1.3.6.1.4.1.32050.2.2.28
Object
The amount of time since the last failed start of the standby power source . This timer resets and starts timing upon a unsuccessful start of the power source. This timer can be reset via the web interface or by writing 0 to this object.
Context
- MIB
- PACKETFLUX-STANDBYPOWER
- OID
.1.3.6.1.4.1.32050.2.2.28- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- standbypower
- Siblings
- 55
Syntax
SNMPv2-SMITimeTicks
- Source
- SNMPv2-SMITimeTicks
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| powercontrollerstate The status of the standby power controller. | scalar | Enumeration | .1.3.6.1.4.1.32050.2.2.1 |
| pwr1voltage The voltage of the DC input Pwr3 in 1/10ths of
a volt. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.10 |
| pwr2voltage The voltage of the DC input Pwr2 in 1/10ths of
a volt. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.11 |
| shuntvoltage The voltage of the DC input Shunt in 1/10ths of
a millivolt. Can be negative. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.32050.2.2.12 |
| temperature The temperature of the onboard temperature sensor
in 1/10ths of a degree centigrade. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.13 |
| recentunsuccessfulstarts The number of times the standby power source was
not successfully started. This counter resets
upon a successful start. It can also be reset
via the web interface or by writing 0 … | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.32050.2.2.14 |
| totalunsuccessfulstarts The number of times the standby power source was
not successfully started. This counter DOES NOT
reset upon a successful start. It can be reset
via the web interface or by writing… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.32050.2.2.15 |
| recentstalls The number of times the standby power source has
stalled. This counter resets upon a clean shutdown.
It can also be reset via the web interface or
by writing 0 to this object. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.32050.2.2.16 |
| totalstalls The number of times the standby power source has
stalled. This counter DOES NOT reset upon a clean
shutdown. It can be reset via the web interface
or by writing 0 to this object. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.32050.2.2.17 |
| numberofstarts The number of times the secondary power source
has started. This counter increments when the
standby sequence reaches the running state. This
counter can be reset via the web inte… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.32050.2.2.18 |
| numberoftransfers The number of times the power has transfered from
primary to standby, or back. A complete transfer
cycle from primary to standby and back to primary
will increment this counter tw… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.32050.2.2.19 |
| transferswitchstate The current state in the transfer sequence. | scalar | Enumeration | .1.3.6.1.4.1.32050.2.2.2 |
| currenttimeonprimary The amount of time the transfer switch has been
in the primary state (position) since the most
recent transfer to that state. This timer resets
to zero when the transfer switch le… | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.20 |
| totaltimeonprimary The amount of time the transfer switch has been
in the primary state (position) since power on
or the last reset of this counter. This timer
does not automatically reset. This tim… | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.21 |
| currenttimeonstandby The amount of time the transfer switch has been
in the standby state (position) since the most
recent transfer to that state. This timer resets
to zero when the transfer switch le… | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.22 |
| totaltimeonstandby The amount of time the transfer switch has been
in the standby state (position) since power on
or the last reset of this counter. This timer
does not automatically reset. This tim… | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.23 |
| currentstandbyruntime The amount of time the standby power source has
been running during it's current run. This timer
resets to zero when the standby power source
shuts down. This timer can be reset v… | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.24 |
| totalstandbyruntime The amount of time the standby power source has
been running since power on or the last reset
of this counter. This timer does not automatically
reset. This timer can be reset via… | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.25 |
| standbypowerConformance | node | - | .1.3.6.1.4.1.32050.2.2.256 |
| laststandbyrun The amount of time since the standby power source
ran last. This timer resets upon start of the
standby power source and starts timing upon shutdown
of the standby power source. T… | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.26 |
| laststandbygracefulstop The amount of time since standby power source
was gracefully shutdown. This timer resets and
starts timing upon graceful shutdown of the standby
power source. This timer can be re… | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.27 |
| laststandbyfailure The amount of time since the stall or failure
while running of the standby power source . This
timer resets and starts timing upon a stall/failure
of the power source. This timer … | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.32050.2.2.29 |
| standbypowerstate The current state in the standby power sequence. | scalar | Enumeration | .1.3.6.1.4.1.32050.2.2.3 |
| switch1closed True(1) if the Switch 1 input is closed (shorted/on).
False(2) if it is open. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.30 |
| switch2closed True(1) if the Switch 2 input is closed (shorted/on).
False(2) if it is open. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.31 |
| switch3closed True(1) if the Switch 3 input is closed (shorted/on).
False(2) if it is open. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.32 |
| switch4closed True(1) if the Switch 4 input is closed (shorted/on).
False(2) if it is open. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.33 |
| switch5closed True(1) if the Switch 5 input is closed (shorted/on).
False(2) if it is open. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.34 |
| enabled True(1) if the enable input is closed (shorted/on).
False(2) if it is open. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.35 |
| relay1on True(1) if the Relay 1 ouput is on (C and NO connected).
False(2) if it is off (C and NC connected). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.36 |
| relay2on True(1) if the Relay 2 ouput is on (C and NO connected).
False(2) if it is off (C and NC connected). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.37 |
| relay3on True(1) if the Relay 3 ouput is on (C and NO connected).
False(2) if it is off (C and NC connected). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.38 |
| relay4on True(1) if the Relay 4 ouput is on (C and NO connected).
False(2) if it is off (C and NC connected). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.39 |
| ac1voltage The voltage of the AC input AC1 in 1/10ths of
a volt. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.4 |
| relay5on True(1) if the Relay 5 output is on (C and NO
connected). False(2) if it is off (C and NC connected). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.40 |
| relay6on True(1) if the Relay 6 output is on (C and NO
connected). False(2) if it is off (C and NC connected). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.41 |
| relay7on True(1) if the Relay 7 output is on (C and NO
connected). False(2) if it is off (C and NC connected). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.42 |
| ruleswitchstandby True(1) if the switch to standby rule is true.
False(2) if it is not. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.43 |
| rulereturnprimary True(1) if the return to primary rule is true.
False(2) if it is not. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.44 |
| rulestandbygood True(1) if the standby power good rule is true.
False(2) if it is not. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.45 |
| rulestopstandby True(1) if the stop standby and consider it failed
rule is true. False(2) if it is not. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.46 |
| ruleexercisestandby True(1) if the exercise standby without transfer
rule is true. False(2) if it is not. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.47 |
| webcontrol1 True(1) if the webcontrol 1 virtual toggle switch
is in the on position. False(2) if it is not.
This value can be written to affect the position
of the toggle switch. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.48 |
| webcontrol2 True(1) if the webcontrol 2 virtual toggle switch
is in the on position. False(2) if it is not.
This value can be written to affect the position
of the toggle switch. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.49 |
| ac1frequency The frequency of the AC input AC1 in 1/100ths
of a Hertz. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.5 |
| webcontrol3 True(1) if the webcontrol 3 virtual toggle switch
is in the on position. False(2) if it is not.
This value can be written to affect the position
of the toggle switch. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.50 |
| webcontrol4 True(1) if the webcontrol 4 virtual toggle switch
is in the on position. False(2) if it is not.
This value can be written to affect the position
of the toggle switch. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.51 |
| webcontrol5 True(1) if the webcontrol 5 virtual toggle switch
is in the on position. False(2) if it is not.
This value can be written to affect the position
of the toggle switch. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.52 |
| webcontrol6 True(1) if the webcontrol 6 virtual toggle switch
is in the on position. False(2) if it is not.
This value can be written to affect the position
of the toggle switch. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.53 |
| webcontrol7 True(1) if the webcontrol 7 virtual toggle switch
is in the on position. False(2) if it is not.
This value can be written to affect the position
of the toggle switch. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.54 |
| webcontrol8 True(1) if the webcontrol 8 virtual toggle switch
is in the on position. False(2) if it is not.
This value can be written to affect the position
of the toggle switch. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.32050.2.2.55 |
| ac2voltage The voltage of the AC input AC2 in 1/10ths of
a volt. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.6 |
| ac2frequency The frequency of the AC input AC2 in 1/100ths
of a Hertz. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.7 |
| mtr1voltage The voltage of the DC input Mtr1 in 1/10ths of
a volt. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.8 |
| mtr2voltage The voltage of the DC input Mtr2 in 1/10ths of
a volt. | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.32050.2.2.9 |