ospfv3IfTransitDelay

OSPFV3-MIB · .1.3.6.1.2.1.191.1.7.1.7

Object

column r/w seconds Ospfv3UpToRefreshIntervalTC

The estimated number of seconds it takes to transmit
a Link State Update packet over this interface.  LSAs
contained in the update packet must have their age
incremented by this amount before transmission.  This
value should take into account the transmission and
propagation delays of the interface.

Context

MIB: OSPFV3-MIB
OID: .1.3.6.1.2.1.191.1.7.1.7
Type: column
Access: readwrite
Status: current
Units: seconds
Parent: ospfv3IfEntry
Table: ospfv3IfTable
Siblings: 24

Syntax

seconds Ospfv3UpToRefreshIntervalTC

Source: Ospfv3UpToRefreshIntervalTC
Base type: Unsigned32

Values & Constraints

Type Constraints

range: 1..1800

Related Objects

Sibling Objects

Object	Type	Syntax	OID
ospfv3IfIndex The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured.	column	IF-MIBInterfaceIndex	`.1.3.6.1.2.1.191.1.7.1.1`
ospfv3IfRtrDeadInterval The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello int…	column	seconds Ospfv3DeadIntervalRangeTC	`.1.3.6.1.2.1.191.1.7.1.10`
ospfv3IfPollInterval The larger time interval, in seconds, between the Hello packets sent to an inactive, non-broadcast multi-access neighbor.	column	seconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.191.1.7.1.11`
ospfv3IfState The OSPFv3 interface state. An interface may be in standby state if there are multiple interfaces on the link and another interface is active. The interface may be in Down state…	column	Enumeration	`.1.3.6.1.2.1.191.1.7.1.12`
ospfv3IfDesignatedRouter The Router ID of the Designated Router.	column	Ospfv3RouterIdTC	`.1.3.6.1.2.1.191.1.7.1.13`
ospfv3IfBackupDesignatedRouter The Router ID of the Backup Designated Router.	column	Ospfv3RouterIdTC	`.1.3.6.1.2.1.191.1.7.1.14`
ospfv3IfEvents The number of times this OSPFv3 interface has changed its state or an error has occurred. Discontinuities in the value of this counter can occur at re-initializatio…	column	SNMPv2-SMICounter32	`.1.3.6.1.2.1.191.1.7.1.15`
ospfv3IfRowStatus This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on w…	column	SNMPv2-TCRowStatus	`.1.3.6.1.2.1.191.1.7.1.16`
ospfv3IfDemand Indicates whether Demand OSPFv3 procedures (Hello suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be performed on this interface.	column	SNMPv2-TCTruthValue	`.1.3.6.1.2.1.191.1.7.1.17`
ospfv3IfMetricValue The metric assigned to this interface. The default value of the metric is 'Reference Bandwidth / ifSpeed'. The value of the reference bandwidth can be set in the ospfv3ReferenceB…	column	OSPF-MIBMetric	`.1.3.6.1.2.1.191.1.7.1.18`
ospfv3IfLinkScopeLsaCount The total number of Link-scope link state advertisements in this link's link state database.	column	SNMPv2-SMIGauge32	`.1.3.6.1.2.1.191.1.7.1.19`
ospfv3IfInstId Enables multiple interface instances of OSPFv3 to be run over a single link. Each interface instance would be assigned a separate ID. This ID has local link significance only.	column	Ospfv3IfInstIdTC	`.1.3.6.1.2.1.191.1.7.1.2`
ospfv3IfLinkLsaCksumSum The 32-bit unsigned sum of the Link-scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been…	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.191.1.7.1.20`
ospfv3IfDemandNbrProbe Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default.	column	SNMPv2-TCTruthValue	`.1.3.6.1.2.1.191.1.7.1.21`
ospfv3IfDemandNbrProbeRetransLimit The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down.	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.191.1.7.1.22`
ospfv3IfDemandNbrProbeInterval Defines how often the neighbor will be probed.	column	seconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.191.1.7.1.23`
ospfv3IfTEDisabled Indicates whether or not traffic engineering is disabled on the interface when traffic engineering is enabled in the area where the interface is attached. The object is set to th…	column	SNMPv2-TCTruthValue	`.1.3.6.1.2.1.191.1.7.1.24`
ospfv3IfLinkLSASuppression Specifies whether or not link LSA origination is suppressed for broadcast or NBMA interface types. The object is set to value true (1) to suppress the origination.	column	SNMPv2-TCTruthValue	`.1.3.6.1.2.1.191.1.7.1.25`
ospfv3IfAreaId A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone.	column	Ospfv3AreaIdTC	`.1.3.6.1.2.1.191.1.7.1.3`
ospfv3IfType The OSPFv3 interface type.	column	Enumeration	`.1.3.6.1.2.1.191.1.7.1.4`
ospfv3IfAdminStatus The OSPFv3 interface's administrative status. The value formed on the interface; the interface will be advertised as an internal route to some area. The value 'disabled' denotes …	column	OSPF-MIBStatus	`.1.3.6.1.2.1.191.1.7.1.5`
ospfv3IfRtrPriority The priority of this interface. Used in multi-access networks, this field is used in the designated-router election algorithm. The value 0 signifies that the router is not eligi…	column	OSPF-MIBDesignatedRouterPriority	`.1.3.6.1.2.1.191.1.7.1.6`
ospfv3IfRetransInterval The number of seconds between link state advertisement retransmissions for adjacencies belonging to this interface. This value is also used when retransmitting dat…	column	seconds Ospfv3UpToRefreshIntervalTC	`.1.3.6.1.2.1.191.1.7.1.8`
ospfv3IfHelloInterval The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.	column	seconds OSPF-MIBHelloRange	`.1.3.6.1.2.1.191.1.7.1.9`