ospfv3IfHelloInterval
OSPFV3-MIB ·
.1.3.6.1.2.1.191.1.7.1.9
Object
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
Context
- MIB
- OSPFV3-MIB
- OID
.1.3.6.1.2.1.191.1.7.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- ospfv3IfEntry
- Table
- ospfv3IfTable
- Siblings
- 24
Values & Constraints
Type Constraints
range: 1..65535
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ospfv3IfIndex The interface index of this OSPFv3 interface.
It corresponds to the interface index of the
IPv6 interface on which OSPFv3 is configured. | column | IF-MIBInterfaceIndex | .1.3.6.1.2.1.191.1.7.1.1 |
| ospfv3IfRtrDeadInterval The number of seconds that a router's Hello
packets have not been seen before its
neighbors declare the router down on the interface.
This should be some multiple of the Hello int… | column | seconds Ospfv3DeadIntervalRangeTC | .1.3.6.1.2.1.191.1.7.1.10 |
| ospfv3IfPollInterval The larger time interval, in seconds, between
the Hello packets sent to an inactive,
non-broadcast multi-access neighbor. | column | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.191.1.7.1.11 |
| ospfv3IfState The OSPFv3 interface state. An interface may be
in standby state if there are multiple interfaces
on the link and another interface is active. The
interface may be in Down state… | column | Enumeration | .1.3.6.1.2.1.191.1.7.1.12 |
| ospfv3IfDesignatedRouter The Router ID of the Designated Router. | column | Ospfv3RouterIdTC | .1.3.6.1.2.1.191.1.7.1.13 |
| ospfv3IfBackupDesignatedRouter The Router ID of the Backup Designated
Router. | column | Ospfv3RouterIdTC | .1.3.6.1.2.1.191.1.7.1.14 |
| ospfv3IfEvents The number of times this OSPFv3 interface has
changed its state or an error has occurred.
Discontinuities in the value of this counter
can occur at re-initializatio… | column | SNMPv2-SMICounter32 | .1.3.6.1.2.1.191.1.7.1.15 |
| ospfv3IfRowStatus This object permits management of the table by
facilitating actions such as row creation,
construction, and destruction.
The value of this object has no effect on
w… | column | SNMPv2-TCRowStatus | .1.3.6.1.2.1.191.1.7.1.16 |
| ospfv3IfDemand Indicates whether Demand OSPFv3 procedures
(Hello suppression to FULL neighbors and
setting the DoNotAge flag on propagated LSAs)
should be performed on this interface. | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.191.1.7.1.17 |
| ospfv3IfMetricValue The metric assigned to this interface.
The default value of the metric is
'Reference Bandwidth / ifSpeed'. The value
of the reference bandwidth can be set
in the ospfv3ReferenceB… | column | OSPF-MIBMetric | .1.3.6.1.2.1.191.1.7.1.18 |
| ospfv3IfLinkScopeLsaCount The total number of Link-scope link state
advertisements in this link's link state
database. | column | SNMPv2-SMIGauge32 | .1.3.6.1.2.1.191.1.7.1.19 |
| ospfv3IfInstId Enables multiple interface instances of OSPFv3
to be run over a single link. Each interface
instance would be assigned a separate ID. This ID
has local link significance only. | column | Ospfv3IfInstIdTC | .1.3.6.1.2.1.191.1.7.1.2 |
| ospfv3IfLinkLsaCksumSum The 32-bit unsigned sum of the Link-scope link state
advertisements' LS checksums contained in this
link's link state database. The sum can be used
to determine if there has been… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.191.1.7.1.20 |
| ospfv3IfDemandNbrProbe Indicates whether or not neighbor probing is
enabled to determine whether or not the neighbor
is inactive. Neighbor probing is disabled by
default. | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.191.1.7.1.21 |
| ospfv3IfDemandNbrProbeRetransLimit The number of consecutive LSA retransmissions before
the neighbor is deemed inactive and the neighbor
adjacency is brought down. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.191.1.7.1.22 |
| ospfv3IfDemandNbrProbeInterval Defines how often the neighbor will be probed. | column | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.191.1.7.1.23 |
| ospfv3IfTEDisabled Indicates whether or not traffic engineering
is disabled on the interface when traffic
engineering is enabled in the area where the
interface is attached. The object is set
to th… | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.191.1.7.1.24 |
| ospfv3IfLinkLSASuppression Specifies whether or not link LSA origination is
suppressed for broadcast or NBMA interface types.
The object is set to value true (1) to suppress
the origination. | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.191.1.7.1.25 |
| ospfv3IfAreaId A 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0 is used for the OSPFv3 backbone. | column | Ospfv3AreaIdTC | .1.3.6.1.2.1.191.1.7.1.3 |
| ospfv3IfType The OSPFv3 interface type. | column | Enumeration | .1.3.6.1.2.1.191.1.7.1.4 |
| ospfv3IfAdminStatus The OSPFv3 interface's administrative status.
The value formed on the interface; the interface
will be advertised as an internal route to some
area. The value 'disabled' denotes … | column | OSPF-MIBStatus | .1.3.6.1.2.1.191.1.7.1.5 |
| ospfv3IfRtrPriority The priority of this interface. Used in
multi-access networks, this field is used in
the designated-router election algorithm. The
value 0 signifies that the router is not
eligi… | column | OSPF-MIBDesignatedRouterPriority | .1.3.6.1.2.1.191.1.7.1.6 |
| ospfv3IfTransitDelay The estimated number of seconds it takes to transmit
a Link State Update packet over this interface. LSAs
contained in the update packet must have their age
incremented by this a… | column | seconds Ospfv3UpToRefreshIntervalTC | .1.3.6.1.2.1.191.1.7.1.7 |
| ospfv3IfRetransInterval The number of seconds between link state
advertisement retransmissions for adjacencies
belonging to this interface. This value is
also used when retransmitting dat… | column | seconds Ospfv3UpToRefreshIntervalTC | .1.3.6.1.2.1.191.1.7.1.8 |