portPoeAdminState
NEXANS-BM-MIB ·
.1.3.6.1.4.1.266.20.3.1.1.21
Object
column
r/w
Enumeration
If no POE adapter is installed this object is read-only and will always report notSupported(1). The possible values are: notSupported(1): No adapter installed or not supported for that port (i.e. uplink port). off(2): Adapter installed but inline power for that port is switched off. forcedOn(3): Adapter installed and inline power is asserted permanently. In the case of an IEEE802.3af adapter this setting will disable the IEEE802.3af automatic detection. autoOn(4): This setting is only supported if a IEEE802.3af adapter is installed. The adapter automatically detects if the connected device is IEEE802.3af compliant and will assert the power if possible. overloadFail(5): Adapter installed but inline power for that port is automatically switched off because of a overload condition at that port.
Context
- MIB
- NEXANS-BM-MIB
- OID
.1.3.6.1.4.1.266.20.3.1.1.21- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- bmSwitchPortEntry
- Table
- bmSwitchPortTable
- Siblings
- 33
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | notSupported |
2 | off |
3 | forcedOn |
4 | autoOn |
5 | overloadFail |
6 | reset |
7 | afHighPower |
8 | atHighPower |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| portIndex A unique value for each port. Its value ranges between 1
and the value of ifNumber.
The port identified by a particular value of this index is
the same port as identified by the … | column | Integer32 | .1.3.6.1.4.1.266.20.3.1.1.1 |
| portTrunkingMode If portTrunkingMode is set to dot1qTagging, all frames are transmited
with a VLAN-tag, except frames which belong to portNativeVlanId.
If portTrunkingMode is set to enableWithout… | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.10 |
| portDot1qDefaultPrioValue The default IEEE802.1Q priority and queue assigned all frames received
on this port, for which no other priorisation applies (IEEE801.1q Tag or
IPv4/IPv6).
The definition betwee… | column | Integer32 | .1.3.6.1.4.1.266.20.3.1.1.11 |
| portDefaultPrioQueue The default priority queue assigned all frames received on this port,
for which no other priorisation applies (IEEE801.1q Tag or IPv4/IPv6).
A value of 0 means the lowest priorit… | column | Integer32 | .1.3.6.1.4.1.266.20.3.1.1.12 |
| portLEDGreen The function of the green port LED. Only supported for user ports | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.13 |
| portLEDYellow The function of the yellow port LED. Only supported for user ports | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.14 |
| portBandwidthLimitRxd The bandwidth limiter for received packets. If set to disable(2) the
limiter will be disabled. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.15 |
| portBandwidthLimitTxd The bandwidth limiter for transmitted packets. If set to disable(2) the
limiter will be disabled. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.16 |
| portSecurityAdminState Enables the port security feature for that port.
A value of notSupported(1) means, that port security ist not supported or
disabled for that port (i.e. uplink port). The command… | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.17 |
| portSecurityMacAddr1 The first MAC address used for port security.
If portSecurityAdminState has the value disable(2), portSecurityManualSettingMacAddr(3)
or vendorSettingMacAddr(12) then this object … | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.266.20.3.1.1.18 |
| portSecurityMacAddr2 The second MAC address used for port security.
If portSecurityAdminState has the value disable(2), portSecurityManualSettingMacAddr(3)
or vendorSettingMacAddr(12) then this object… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.266.20.3.1.1.19 |
| portDescr A textual string containing information about the
interface. Same as ifDescr. | column | OctetString | .1.3.6.1.4.1.266.20.3.1.1.2 |
| portSecurityMacAddr3 The third MAC address used for port security.
If portSecurityAdminState has the value disable(2), portSecurityManualSettingMacAddr(3)
or vendorSettingMacAddr(12) then this object … | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.266.20.3.1.1.20 |
| portPoeVoltage The current PoE output voltage at this port in volts. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.266.20.3.1.1.22 |
| portPoeCurrent The current PoE output current at this port in milliampere. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.266.20.3.1.1.23 |
| portPoePower The current PoE output power at this port in milliwatt. The output
power is the product of portPoeVoltage and portPoeCurrent. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.266.20.3.1.1.24 |
| portSecurityForwardingState The port security forwarding state of that port.
See documentation for details. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.25 |
| portPoePowerLimit The limit for the POE output power at this port in VA. If the
current power exceeds this value a overload conditions occurs and
the inline power for that port will be switched of… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.266.20.3.1.1.26 |
| portLimiterPacketType The packet type for bandwidth limiter. If set to limitAllPacktes(2)
then all packets are limited. If set to limitLoppBcastPackets(3) only
flooted loop- and broadcast-pakets are li… | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.27 |
| portAcApSetup If portAcApSetup is enabled, the switch will perform Autocrossover
and Autopolarity for this port. This function should only be enabled
if portSpeedDuplexSetup ist set to autoneg. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.28 |
| portLinkType The link type of that port. If set to upDownlink(3) the portAdminState
will be forced to enable. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.29 |
| portName An administratively assigned name for this port. | column | OctetString | .1.3.6.1.4.1.266.20.3.1.1.3 |
| portVoiceVlanId The Voide-VLAN-ID assigned to this port.
Packets of this Voice-VLAN are allway send with a VLAN-Tag, because
IP-Phones normaly need a tagged VLAN.
If portTrunkingMode is set to do… | column | Integer32 | .1.3.6.1.4.1.266.20.3.1.1.30 |
| portPrioDot1p Defines whether port prioritisation for IEEE802.1p packets is enabled. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.31 |
| portPrioIp Defines whether port prioritisation for IPv4/IPv6 packets is enabled. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.32 |
| portActiveDefaultVlanId The currently active Default-VLAN-ID assigned to this port.
This is either the configured portDefaultVlanId or the VLAN ID
assigned by RADIUS authentication | column | Integer32 | .1.3.6.1.4.1.266.20.3.1.1.33 |
| portActiveVoiceVlanId The currently active Voice-VLAN-ID assigned to this port.
This is either the configured portVoiceVlanId or the VLAN ID
assigned by RADIUS authentication | column | Integer32 | .1.3.6.1.4.1.266.20.3.1.1.34 |
| portAdminState A value indicating the current state of the port.
A SET to this object enables (2) or disables (3) the port.
The possible values returned by GET are:
allwaysEnable(1)
The port… | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.4 |
| portSpeedDuplexSetup A value indicating the current speed and duplex link setup.
Independent of portSpeedDuplexSetup the port may be disabled
by portAdminState. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.5 |
| portLinkState A value indicating the current link state. | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.6 |
| portErrorCounter Errors are usually caused by a FDX/HDX mismatch between the switch port
and the connected port. If the switch detects a incrementation of this
counter, he will send a portErrorCou… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.266.20.3.1.1.7 |
| portRemoteFault If portRemoteFault is enabled for this port, the port transmitter will
be only enabled if the port receiver has a valid link (portLinkState must
not be down). | column | Enumeration | .1.3.6.1.4.1.266.20.3.1.1.8 |
| portDefaultVlanId The Default-VLAN-ID assigned to this port.
This Default-VLAN-ID has differnt affects depending on received
or transmited frames:
a) All received frames, which have no VLAN-tag, wi… | column | Integer32 | .1.3.6.1.4.1.266.20.3.1.1.9 |