mfpUrl

MX-FPU-MIB · .0.1300.1.450

Object

scalar r/w OctetString

MFP URL
          
URL of the MFP 'single file' to install. The supported transfer
protocols are:
          
  * HTTP
  * HTTPS
  * TFTP
  * FTP
          
Examples of valid URLs:
          
  * http://www.myserver.com/myfile.bin
  * tftp://myserver.com:69/myfolder/myfile.bin
          
When the port is not included in the URL, the default port for
the chosen protocol is used.
          
For authentication, it is recommended to use the
Fpu.MfpTransferUsername and Fpu.MfpTransferPassword parameters.
The credentials may also be provisioned directly in the URL
using the syntax protocol://[username[:password]@]hostname
[:port]/[path/]filename with the following constraints:
          
  * No '/', ':' and '@' characters should be present in username
    or password.
  * No percent escaping.
  * The password will appear in clear in the URL field in the
    Web page.
          
If a username/password is specified both in the URL and in the
provisioning parameters, values specified in the URL will have
precedence over the ones specified in the parameters.
          
This parameter may contain some macros that are substituted by
the actual value at the moment of fetching the MFP file.
          
The supported macros are:
          
  * %mac% - the MAC address of the unit.
  * %product% - the product name of the unit.
  * %productseries% - the product series name of the unit.
  * %serial% - the serial number of the unit.

Context

MIB: MX-FPU-MIB
OID: .0.1300.1.450
Type: scalar
Access: readwrite
Status: current
Parent: fpuMIBObjects
Siblings: 11

Syntax

OctetString

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects

Object	Type	Syntax	OID
mfpInstalledInfoTable Installed MFPs List of Firmware Packs that are currently installed on the unit.	table	-	`.0.1300.1.100`
status Status Indicates the current status of the Firmware Pack Updater. * WaitingSystemReady: Waiting for the system restart to complete. * Idle: Ready to …	scalar	Enumeration	`.0.1300.1.110`
mfpLastInstallationResult Last Result Result of the last Install command. * None: No installation result available. * Success: The last installation succeeded. * Fail: The last …	scalar	Enumeration	`.0.1300.1.125`
mfpLastInstallationDateTime Firmware Installation Date and Time Date and time when the firmware was installed.	scalar	OctetString	`.0.1300.1.150`
mfpRollbackAvailable Rollback Available Indicates whether or not a MFP rollback operation is available.	scalar	Enumeration	`.0.1300.1.175`
mfpRepositoryGroup	node	-	`.0.1300.1.400`
automaticRestartEnable Automatic Restart Enables the firmware pack updater to automatically restart the system when needed for completing a firmware update operation. Also see the …	scalar	MX-TCMxEnableState	`.0.1300.1.500`
automaticRestartGraceDelay Automatic Restart Grace Delay Configures the grace delay in minutes that the unit waits for all telephony calls to be terminated before the automatic restart can occur.…	scalar	Unsigned32	`.0.1300.1.600`
notificationsGroup	node	-	`.0.1300.1.60010`
configurationGroup	node	-	`.0.1300.1.60020`
defaultSettingsOnInstall Default Settings On Firmware Installation. When set to 'Enable', the unit automatically executes a factory reset upon completion of a firmware installation.	scalar	MX-TCMxEnableState	`.0.1300.1.700`