agentSecureAddressFlag
MS-SWITCH30-MIB ·
.1.3.6.1.4.1.3181.10.3.2.10
Object
scalar
Enumeration
This Entry documents the Flag which is set from the system if invalid values for MAC-address, IP-address or subnet mask have been found in the stored configuration. In this case hard coded secure values are used instead of those found. This flag is cleared if valid valued are found when the system comes up.
Context
- MIB
- MS-SWITCH30-MIB
- OID
.1.3.6.1.4.1.3181.10.3.2.10- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- agent
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | useSecure |
2 | useNormal |
255 | unsupported |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| agentFirmware This entry contains the firmware version
of the agent. | scalar | OctetString | .1.3.6.1.4.1.3181.10.3.2.1 |
| agentStorageMediaCardStatus This Entry represents the detected status
of a storage memory card if supported. | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.11 |
| agentStorageMediaCardBoot Set this entry to '1' before setting the
entry 'agentConfigReset' to '1' sets the
device's config to the values stored on
the Storage Media Card once if available .
and the entr… | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.12 |
| agentStorageMediaCardMac Set this entry to '1' before setting the
entry 'agentConfigReset' to '1' leads to
take the MAC address from the SMC. Be very
careful with this service option to avoid
duplicated… | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.13 |
| agentStoreConfigToStorageMediaCard Set this entry to '1' to store the
present configuration to the storage
media card if available.
This entry is self clearing. | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.14 |
| agentDhcpConfigRequest Setting this entry to a '1' enables the
DHCP config request feature if available. | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.15 |
| agentMacAddress This entry contains the mac address of
the agent. | scalar | RFC1213-MIBPhysAddress | .1.3.6.1.4.1.3181.10.3.2.2 |
| agentIpv4Mode This entry describes the IPv4-mode
of the agent. | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.3 |
| agentIpv4Address This entry contains the IPv4-address of
the agent. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.3181.10.3.2.4 |
| agentIpv4SubnetMask This entry contains the IPv4 subnet mask
of the agent. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.3181.10.3.2.5 |
| agentIpv4Gateway This entry contains the gateway IPv4 address
for the agent. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.3181.10.3.2.6 |
| agentConfigReset Set this entry to '1' to reset the device.
This entry is self clearing. | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.7 |
| agentConfigFactoryDefault Set this entry to '1' before setting the
entry 'agentConfigReset' to '1' sets the
device to factory defaults once and the
entry is self cleared. Setting this entry
to '2' it w… | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.8 |
| agentConfigEnableFactoryButton Setting this entry to a '1' enables
the hardware button for a factory
reset if available. | scalar | Enumeration | .1.3.6.1.4.1.3181.10.3.2.9 |