tcpServerAllowDriverControl
MOXA-W2x50A-MIB ·
.1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.5
Object
column
r/w
Enumeration
If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort W2x50A series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.
Context
- MIB
- MOXA-W2x50A-MIB
- OID
.1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- tcpServerEntry
- Table
- tcpServerTable
- Siblings
- 8
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disable |
1 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tcpServerTcpAliveCheck The TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device server
automatically closes the TCP… | column | Integer32 | .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.1 |
| tcpServerInactivityTime 0 ms: TCP connection is not closed when the
serial line is idle.
1-65535 ms: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no serial da… | column | Integer32 | .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.2 |
| tcpServerMaxConnection Max connection is usually used when the user needs
to receive data from different hosts simultaneously.
The factory default is 1. In this case, only one
specific host can access t… | column | Integer32 | .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.3 |
| tcpServerIgnoreJammedIp Previously, when Max connection was set to a value
greater than 1, and the serial device was
transmitting data, if any one of the connected hosts
stopped responding, the serial de… | column | Enumeration | .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.4 |
| tcpServerTcpPort The 'TCP port' is the TCP port that the NPort
W2x50A series device server uses to listen to
connections, and that other devices must use to
contact the NPort W2x50A series device… | column | Integer32 | .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.6 |
| tcpServerCmdPort The 'Command port' is a TCP port used to listen for
SSDK commands from the host. In order to
prevent a TCP port conflict with other applications,
the user can set the Command por… | column | Integer32 | .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.7 |
| tcpServerConnectionDownRTS For some applications, serial devices must obtain
the Ethernet link status from the RTS signal sent by the
NPort W2x50A series device server. If this setting is
set to 'goes low,'… | column | Enumeration | .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.8 |
| tcpServerConnectionDownDTR For some applications, serial devices must obtain
the Ethernet link status from the DTR signal sent by the
NPort W2x50A series device server. If this setting is
set to 'goes low,'… | column | Enumeration | .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.9 |