wdmIfFecFailure
LUM-WDM-MIB ·
.1.3.6.1.4.1.8708.2.4.2.2.1.1.103
Object
column
LUM-TCFaultStatus
Too many errors to get valid FEC statistics. It is not
possible to run control loops based on FEC statistics.
A: Too many errors to get valid FEC statistics.
D: The FEC statistics is valid.
Context
- MIB
- LUM-WDM-MIB
- OID
.1.3.6.1.4.1.8708.2.4.2.2.1.1.103- Type
- column
- Access
- readonly
- Status
- current
- Parent
- wdmIfEntry
- Table
- wdmIfTable
- Siblings
- 122
Values & Constraints
Type Values
1 | ok |
2 | alarm |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wdmIfIndex An arbitrary index assigned to each if entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.1 |
| wdmIfHighSpeedMax The maximum speed in units of 1,000,000 bits per
second. If this object reports a value of 'n' then
the speed of the interface is somewhere in the
range of 'n-500,000' to 'n+499,9… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.10 |
| wdmIfFarEndLoopbackTimeout Timeout for far end loopback (a.k.a. facility
loopback) to make sure connection to node is
not lost if ppp link is broken.
The unit is hour. 0.1 means 6 minutes. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.100 |
| wdmIfFarEndLoopbackEnabled Far end loopback (a.k.a. facility loopback)
is enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.101 |
| wdmIfChangeLoopbackCommand Command to change Loopback and loopbacktimeout | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.102 |
| wdmIfTxSignalStatus The operational state for outgoing (TX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The s… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.104 |
| wdmIfRxSignalStatus The operational state for incoming (RX) signal
of the interface.
down - A major fault has occurred
degraded - The signal quality is impaired.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.105 |
| wdmIfNearEndLoopback Loop the wdm TX signal back to the wdm RX.
This is also called Terminal loopback.
disabled - the signal is not looped
enabled - the signal is looped. | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.106 |
| wdmIfNearEndLoopbackTimeout Timeout for near end loopback (a.k.a. terminal
loopback) to make sure connection to node is
not lost if ppp link is broken.
The unit is hours. 0.1 means 6 minutes. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.107 |
| wdmIfNearEndLoopbackEnabled Near end loopback (a.k.a. terminal loopback)
is enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.108 |
| wdmIfChangeNearEndLoopbackCommand Command to change near end loopback (a.k.a.
terminal loopback) and loopbacktimeout | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.109 |
| wdmIfPowerLevel The received power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.11 |
| wdmIfSignalDegraded Too many error corrected.
If more errors are corrected
it might effect the client signal
in a negative way. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.110 |
| wdmIfHubProtectionMode Choose if the line should be used in
hub protection. (needs to be setup in mba)
disabled - Port is not in hub protection (default)
enabled - Hub prot… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.111 |
| wdmIfActualFormat The actual signal format. | column | LUM-TCSignalFormat | .1.3.6.1.4.1.8708.2.4.2.2.1.1.112 |
| wdmIfTdcDispersion Shows current dispersion value in the unit. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.113 |
| wdmIfTdcDispersionCommand Sets state and dispersion in the unit. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.114 |
| wdmIfTdcDispersionMode States the current mode of the TDC dispersion.
Mode:
auto - The TDC is in auto optimising state.
startValue - Starts with the desired value,
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.115 |
| wdmIfLineControlLoopCurrentState The current state of the unit. The unit
is ready if state=Automatic fine-tuning.
The states could be one of the followings:
Init DPSK.
… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.116 |
| wdmIfSignalDegradeThreshold Threshold for signal degraded alarm,
based on BER value.
The threshold is settable on the first
line port, affecting all line ports.
Predefined BER l… | column | LUM-TCBerLevel | .1.3.6.1.4.1.8708.2.4.2.2.1.1.117 |
| wdmIfTrxThresholdOptimizationState Threshold Optimization State.
Idle - No regulation done
Searching - Rough threshold regulation
is bein… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.118 |
| wdmIfTrxDecisionThreshold The threshold is automatically optimized if the
'Continous optimization' functionality is enabled.
Press the 'Optimize' button to manually trigger
the optimization routine once. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.119 |
| wdmIfPowerLevelHighThreshold The upper threshold for received power level in
units of 0.1 dBm.
Note: Depending on the type of board and interface
the value range may vary. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.12 |
| wdmIfSwControlledLaserShutdown enabled - the laser is turned off for a specified time, until the timer expires
disabled - normal state | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.120 |
| wdmIfChangeSwControlledLaserShutdownCommand Command to shut the laser down for a user-defined period of time.
This setting will over-ride other laser control functions like ALS and protection.
The timer can be selected in m… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.121 |
| wdmIfControlledLaserShutdownEnabled Software controlled laser shutdown is enabled.
Activation - When the command is successfully applied.
De-activation - When the timer expires, or the operation is manually cancelle… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.122 |
| wdmIfAid The access identifier (AID) of the interface.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.123 |
| wdmIfPhysicalLocation The physical location of the if. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.124 |
| wdmIfPowerLevelLowThreshold The lower threshold for received power level in
units of 0.1 dBm.
Note: Depending on the type of board and interface
the value range may vary. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.13 |
| wdmIfLaserTemp The pre-set laser temperature in units of
0.1 degrees centigrade. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.14 |
| wdmIfLaserTempOffset The current offset from the pre-set temperature
in units of 0.1 degrees centigrade. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.15 |
| wdmIfLaserTempOffsetThreshold The absolute value of the offset for the LTL
and LTH alarms in units of 0.1 degrees centigrade. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.16 |
| wdmIfLaserMode The administrative state of the TX-side laser.
on - The laser is turned on.
als - Automatic Laser Shutdown/Turn-Off
when lossOfSignal is detected on … | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.17 |
| wdmIfLaserStatus The operational state of the TX-side laser.
off - The laser is turned off.
on - The laser is turned on. | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.18 |
| wdmIfAdminStatus The administrative state for the interface.
down - The interface is de-activated.
service - The interface is activated but alarms
are suppressed. Int… | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.19 |
| wdmIfName The management name of the interface, for example
'wdm:1:2:1'. | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.2 |
| wdmIfOperStatus The operational state for the interface.
notPresent - The interface is not available.
down - The interface is de-activated or there are
faults preven… | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.20 |
| wdmIfLossOfSignal Loss of signal.
Applicable for all signal formats.
A(ctivation): Active loss of signal HW indication.
D(e-activation): Inactive loss of signal HW
ind… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.21 |
| wdmIfReceivedPowerHigh Received power level is too high.
Applicable for all signal formats.
A: The received power level exceeds the
the built-in overload threshold.
D: The … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.22 |
| wdmIfReceivedPowerLow Received power level low threshold exceeded.
Applicable for all signal formats.
A: The received power level is below the
associated threshold.
D: The… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.23 |
| wdmIfLaserBiasHigh Laser bias high threshold exceeded.
A: The laser bias current exceeds the associated
threshold.
D: The laser bias current is 0.5 mA below the
associa… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.24 |
| wdmIfErroredSeconds deprecated Note: This attribute is deprecated!
Errored seconds (ES) threshold exceeded.
A: The number of errored seconds during a period
exceeds the associated … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.25 |
| wdmIfSeverelyErroredSeconds deprecated Note: This attribute is deprecated!
Severely errored seconds (SES) threshold exceeded.
A: The number of severely errored seconds during
a period exce… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.26 |
| wdmIfBackgroundBlockErrors deprecated Note: This attribute is deprecated!
Background block errors (BBE) threshold exceeded.
A: The number of errors during a period
exceeds the associated … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.27 |
| wdmIfUnavailableSeconds deprecated Note: This attribute is deprecated!
Unavailable seconds (UAS) threshold exceeded.
A: The number of unavailable seconds during a
period exceeds the as… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.28 |
| wdmIfForwardDefectIndication Forward defect indication.
Applicable for all signal formats; detected at
WDM level. This alarm suppresses the
corresponding SDH/Sonet alarm.
A: Forward defect indi… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.29 |
| wdmIfDescr User configurable label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.3 |
| wdmIfBackwardDefectIndication Backward defect indication.
Applicable for all signal formats; detected at
WDM level. This alarm suppresses the
corresponding SDH/Sonet alarm.
A: Backward defect in… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.30 |
| wdmIfLossOfFrame Loss of frame.
Applicable for SDH/Sonet signal formats.
A: SDH frame can not be located.
D: SDH frame is located. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.31 |
| wdmIfAlarmIndicationSignal Alarm indication signal.
Applicable for SDH/Sonet signal formats.
For other proprietary formats, e.g. for
the tpDDGbE line signal, a similar
functionality is emulated.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.32 |
| wdmIfRemoteDefectIndication Remote defect indication.
Applicable for SDH/Sonet signal formats.
A: RDI indication (in SDH/Sonet frame) active.
D: RDI indication inactive. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.33 |
| wdmIfLossOfSync Loss of sync (GbE).
Applicable for GbE signal formats.
A: GbE 'frame' can not be located.
D: GbE 'frame' is located. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.34 |
| wdmIfLossOfForwardingErrorCorrection Loss of forwarding error correction (FEC).
Applicable for all signal formats.
A: The interface is unable to perform forwarding
error correction.
D: T… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.35 |
| wdmIfLaserTempHigh Laser temperature high threshold exceeded.
A: The temperature exceeds the associated
threshold.
D: Temperature is 0.5 degrees centigrade below
the as… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.36 |
| wdmIfLaserTempLow Laser temperatur low threshold exceeded.
The temperature exceeds the associated threshold.
A: The temperature exceeds the associated
threshold.
D: Te… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.37 |
| wdmIfRxPort The number of the port where the interface is
located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.4.2.2.1.1.38 |
| wdmIfBitrateMismatch Bitrate mismatch (Other).
Applicable for other signal formats.
A: The interface is unable to lock to the
inserted signal.
D: The interface is able to… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.39 |
| wdmIfSubrack The number of the subrack where the interface
is located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.4.2.2.1.1.4 |
| wdmIfLaserBias Measures laser bias current value in tenths of
mA (0.1 mA). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.40 |
| wdmIfLaserBiasThreshold Sets the threshold for the laser bias alarm.
in percentage relative to the value set during
production. The preset value is 100%. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.41 |
| wdmIfLossOfSignalThreshold The upper threshold received power level in
units of 0.1 dBm.
Note: Depending on the type of board and interface
the value range may vary. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.42 |
| wdmIfJ0PathTrace deprecated The received J0 path trace string.
Applicable for SDH/Sonet signal formats. | column | OctetString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.44 |
| wdmIfInbandMode deprecated The administrative state the in-band management
channel of the WDM interface.
down - The management channel is disabled.
up - The management channel … | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.45 |
| wdmIfInbandStatus deprecated The operational state the in-band management
channel of the WDM interface.
down - The management channel is disabled.
up - The management channel is … | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.46 |
| wdmIfExpectedTxLambda The expected frequency or wavelength.
ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.
The semantic of this attribute is different dependi… | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.4.2.2.1.1.47 |
| wdmIfForwardingErrorCorrectionMode The administrative state of the forwarding error
correction function.
disabled - FEC is disabled.
enabled - FEC is activated.
auto - a… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.48 |
| wdmIfUnexpectedTxLambda The actual frequency does not match the
pre-configured frequency.
A pre-configured frequency of '0' matches
all actual frequencies.
A: The configured… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.49 |
| wdmIfSlot The number of the slot where the interface is
located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.4.2.2.1.1.5 |
| wdmIfTraceIntrusionMode Indicates whether the trace identifier should be
inserted in the transmitted signal.
disabled - The trace identifier is taken from
the received signal if possible.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.50 |
| wdmIfTraceTransmitted The trace identifier to be transmitted from this
interface.
The identifier length is by default 0 to 15. For
mxp8iiSonet boards the length is 0 to 62.
… | column | OctetString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.51 |
| wdmIfTraceReceived The received trace identifier for this interface. | column | OctetString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.52 |
| wdmIfTraceExpected Trace identifier used for matching against
the received trace identifier.
The identifier length is by default 0 to 15. For
mxp8iiSonet boards the length is 0 to 62. | column | OctetString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.53 |
| wdmIfTraceAlarmMode Controls if the trace identifier mismatch alarm
should be raised.
disabled - The alarm is disabled.
enabled - The alarm is raised if expected trace
i… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.54 |
| wdmIfTraceMismatch Indicates if the expected trace identifier
differs from the received trace identifier.
A: The received trace identifier differs from
the expected trace identifier.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.55 |
| wdmIfLaserStatusLastChangeTime The time when the laser status was last changed. | column | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.8708.2.4.2.2.1.1.56 |
| wdmIfSuppressRemoteAlarms Suppress AIS, FDI and RDI in the alarm list. The
fault status on the port object can, however, be
seen.
disabled - alarms are not suppressed.
enabled… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.57 |
| wdmIfSerialNumberMismatch Wrong HW unit installed. The link has not been
optimized for this individual, wrong serial number.
Action: The installation optimization procedure must
be run again… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.58 |
| wdmIfOptimizeDecisionThreshold Optimize the threshold for distinguishing between
1s and 0s.
This attribute is of 'action type' - it will always
have the value 'normal'
normal - jus… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.59 |
| wdmIfTxPort The number of the port where the interface is
located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.4.2.2.1.1.6 |
| wdmIfThresholdOptimizationState State of the optimization procedure
normal - no operation has been started
started - the operation is started
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.60 |
| wdmIfUseHwDefaultDecisionThreshold Use the HW default decision threshold.
This attribute is of 'action type' - it will always
have the value 'normal'
normal - just a placeholder, is ne… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.61 |
| wdmIfFecCorrectedZeros The number of corrected zeros. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.62 |
| wdmIfFecCorrectedOnes The number of corrected ones. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.63 |
| wdmIfOptimizedForSerialNumber This field contains the serial number of
the transponder unit, for which the decision
threshold is optimized and stored. | column | OctetString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.64 |
| wdmIfRelativeDecisionThreshold The 1/0 decision threshold computed at installation.
The threshold is automatically optimized if the
'Continous optimization' functionality is enabled.
Press the 'O… | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.65 |
| wdmIfTrxCodeMismatch The inserted transceiver does not have a legal
manufacturer code.
A: A transceiver with illegal code is inserted.
D: The transceiver with illegal cod… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.66 |
| wdmIfTrxBitrateUnavailable The inserted transceiver does not support the
requested bit rate.
A: A transceiver with other supported bit rate than
the requested bit rate is inserted.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.67 |
| wdmIfTrxMissing An expected transceiver is missing.
A: An expected transceiver is missing.
D: The missing transceiver is inserted. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.68 |
| wdmIfTrxClass String that describes the transceiver class. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.69 |
| wdmIfInvPhysIndexOrZero The row in the invPhysTable for this interface.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.7 |
| wdmIfLaserTempHighRelativeThreshold Threshold for the Laser Temp High alarm, expressed
as an offset from a pre-set nominal temperature,
in units of 0.1 degrees centigrade. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.70 |
| wdmIfLaserTempLowRelativeThreshold Threshold for the Laser Temp Low alarm, expressed
as an offset from a pre-set nominal temperature,
in units of 0.1 degrees centigrade. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.71 |
| wdmIfTransmitterFailed The transceiver HW has detected a failure
in the transmitter part.
A: The transmitter has failed
D: The transmitter is OK again | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.72 |
| wdmIfReceiverSensitivity The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.73 |
| wdmIfPowerLevelLowRelativeThreshold The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity, or loss of signal threshold.
- For fixed transceivers it is m… | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.74 |
| wdmIfIllegalFrequency The frequency supported by the transceiver is not
recognized by the system.
A: Invalid or unknown frequency information is
detected in the (pluggable) transceive… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.75 |
| wdmIfLaserForcedOn When enabled, the laser is on regardless of whether
there is a client signal or not.
disabled - the laser is only on when there is a
client signal.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.76 |
| wdmIfTrafficCombination Specifies how different traffic formats can be
combined on different ports on gxp2500, gxp2500Sfp,
fhmxp10g, msMxp10G and msMxp. All combinations
can not be used on all boards.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.77 |
| wdmIfSelectTrafficCombination Select the traffic combination of the board. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.78 |
| wdmIfObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.4.2.2.1.1.79 |
| wdmIfTxLambda The transmitted frequency given in hundreds of
GHz (0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.4.2.2.1.1.8 |
| wdmIfTxPowerLevel The transmitted power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.80 |
| wdmIfLaserTempActual The actual laser temperature in units of
0.1 degrees centigrade. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.81 |
| wdmIfTrxFailed A transceiver hardware failure is detected.
A: The transceiver fails.
D: The transceiver is replaced. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.82 |
| wdmIfDisabled The interface is disabled.
A: Interface disabled.
D: Interface enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.83 |
| wdmIfLoopback The interface is set in loopback mode.
A: Loopback enabled.
D: Loopback disabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.84 |
| wdmIfContinousOptimization Continuously run the optimization of the
decision threshold.
enabled - continous optimization enabled.
disabled - continous optimization disabled. | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.85 |
| wdmIfThresholdOptimizationResultCause This text descibes the cause why the latest
optimize command failed. The information
is only valid if the thresholdOptimizationState
is finishedFailed. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.86 |
| wdmIfDistributionRole Note: This attribute is deprecated!
The distribution role of the line function
- terminal: normal point-to-point operation
- broadcastHub: broadcast on both lines.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.87 |
| wdmIfConfigurationCommand Note: This attribute is deprecated!
Select the operation mode of the line.
- terminal: normal point-to-point operation
- broadcastHub: broadcast on b… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.88 |
| wdmIfNoFrequencySet The tunable laser frequency has not been set.
A: Tunable laser frequency is not set.
D: Tunable laser frequency is set. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.89 |
| wdmIfHighSpeedMin The minimum speed in units of 1,000,000 bits per
second. If this object reports a value of 'n' then
the speed of the interface is somewhere in the
range of 'n-500,000' to 'n+499,9… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.8708.2.4.2.2.1.1.9 |
| wdmIfFormat The signal format
FecLan10GbE1A: iWDM 10G framing format type 1A (TPD10GBE-BU, GBE9/MXP10GFEC)
FecLan10GbE1B: iWDM 10G framing format type 1B (TPQ10GFEC, MS-MXP/10G… | column | LUM-TCSignalFormat | .1.3.6.1.4.1.8708.2.4.2.2.1.1.90 |
| wdmIfConfigurationFormatCommand Command to change the signal format.
OTU-2 can be selected. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.2.1.1.91 |
| wdmIfOHTransparency deprecated Note: This attribute is deprecated!
The 'OH Transparency' setting shall be set to 'off'
for standard SDH/SONET mode. Does not work when
client wrapper is enabled.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.92 |
| wdmIfLinkDown deprecated Note: This attribute is deprecated!
A: Failure to negotiate a connection with the
other party.
D: A connection is negotiated. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.2.1.1.93 |
| wdmIfAutoNegotiationMode deprecated Note: This attribute is deprecated!
The wanted auto negotiation mode.
off - auto negotiation process is disabled
on - a… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.94 |
| wdmIfAutoNegotiationStatus deprecated Note: This attribute is deprecated!
The result of the auto negotiation procedure
incomplete - the result is still pending
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.95 |
| wdmIfFlowControlMode deprecated Note: This attribute is deprecated!
The mode for handling of pause messages between
the peers.
noPause - PAUSE frame reception and
t… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.96 |
| wdmIfGroupLineMode Indicates whether the interface is grouped
into a ROADM-Line-group.
disabled - The interface is not grouped into
a ROADM-Line-group.
enabled - The in… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.97 |
| wdmIfFecType Set type of FEC.
enhancedFec - 2nd generation Enhanced FEC
(rate compatible with G.709
but > 2 dB additional coding
gain)
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.98 |
| wdmIfFarEndLoopback Loop the wdm RX signal back to the wdm TX.
This is also called Facility loopback.
disabled - the signal is not looped
enabled - the signal is looped. | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.2.1.1.99 |