roadmAddDropIfGroupIndex
LUM-ROADM-MIB ·
.1.3.6.1.4.1.8708.2.31.2.2.1.1.40
Object
column
SNMPv2-SMIUnsigned32
The index of the associated ROADM-group, if any. If no group is created, it is set to 0
Context
- MIB
- LUM-ROADM-MIB
- OID
.1.3.6.1.4.1.8708.2.31.2.2.1.1.40- Type
- column
- Access
- readonly
- Status
- current
- Parent
- roadmAddDropIfEntry
- Table
- roadmAddDropIfTable
- Siblings
- 42
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| roadmAddDropIfIndex An arbitrary index assigned to each entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.31.2.2.1.1.1 |
| roadmAddDropIfOperStatus The operational state for the interface.
notPresent - The physical resources are not
available.
down - The interface is de-activated or the are
fault… | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.31.2.2.1.1.10 |
| roadmAddDropIfTemperature The temperature in the add/drop module in 0.1 degrees centigrade. | column | Integer32 | .1.3.6.1.4.1.8708.2.31.2.2.1.1.11 |
| roadmAddDropIfDropFrequencyMin Lowest added channel in hundreds of
GHz (0.01 GHz).
Supported range 19185 ... 19598 (ch9185 .. ch958)
This attribute can be written via SNMP. | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.31.2.2.1.1.12 |
| roadmAddDropIfDropFrequencyMax Highest added channel in hundreds of
GHz (0.01 GHz).
Supported range 19185 ... 19580 (ch9185 .. ch958)
This attribute can be written via SNMP. | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.31.2.2.1.1.13 |
| roadmAddDropIfObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.31.2.2.1.1.14 |
| roadmAddDropIfConfigurationCommand Configure the drop frequencies.
Express mode - All the channels will go through the express port
of the drop section (Ext Tx). No channels will go through the
drop … | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.15 |
| roadmAddDropIfModuleFailure The module HW has detected a failure.
A: The module has failed
D: The module is OK again | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.31.2.2.1.1.16 |
| roadmAddDropIfTxSignalStatus The operational state for the dropped (TX) signal
of the interface.
down - The signal is turned off.
degraded - The signal quality is impaired.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.31.2.2.1.1.17 |
| roadmAddDropIfMode The drop mode for the interface.
express - No wavelengths are dropped.
drop - Up to eight (15 if 50 GHz spacing is used) channels are possible to dro… | column | Enumeration | .1.3.6.1.4.1.8708.2.31.2.2.1.1.18 |
| roadmAddDropIfDescr2 User configurable label.
This attribute can be written via SNMP. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.19 |
| roadmAddDropIfName The management name of the interface, for
example 'roadmAddDrop:1:2:1-2', where the first number
indicates sub-rack, the second slot number and
the third is the port number.
Examp… | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.2 |
| roadmAddDropIfSpacingMode The spacing mode of the interface.
spacing100GHz: Only 100GHz channels are available
as drop frequencies.
spacing50GHz: Both 50GHz and 100GHz channel… | column | Enumeration | .1.3.6.1.4.1.8708.2.31.2.2.1.1.20 |
| roadmAddDropIfGuardChannel1 When 50GHz spacing is used, the channel before the
minDropFrequency cannot be used for express traffic.
This channel is considered as a guard channel. | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.31.2.2.1.1.21 |
| roadmAddDropIfGuardChannel2 When 50GHz spacing is used, the channel after the
maxDropFrequency cannot be used for express traffic.
This channel is considered as a guard channel. | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.31.2.2.1.1.22 |
| roadmAddDropIfDropFrequencyLimitMin When an Allocated Range is defined, it is not possible
to add channels outside the range.
The supported range is:
roadm1x2G50: [19185 .. 19580] (ch9185 .. ch958) 5… | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.31.2.2.1.1.23 |
| roadmAddDropIfDropFrequencyLimitMax When an Allocated Channel Range is defined, it is not possible
to add channels outside the range.
The supported range is:
roadm1x2G50: [19185 .. 19580] (ch9185 .. … | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.31.2.2.1.1.24 |
| roadmAddDropIfLimitConfigurationCommand When an Allocated Channel Range is defined, it is not possible
to add channels outside the range. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.25 |
| roadmAddDropIfGroupRoadmMode Indicates whether the interface is grouped
into a ROADM-ROADM-group.
disabled - The interface is not grouped into
a ROADM-ROADM-group.
enabled - The … | column | Enumeration | .1.3.6.1.4.1.8708.2.31.2.2.1.1.26 |
| roadmAddDropIfPasswd Password protecting the Allocated Channel Range.
If passwd is '-' (dash), then the password
controll is disabled. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.27 |
| roadmAddDropIfPasswdConfig Change the password protecting the Allocated
Channel Range. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.28 |
| roadmAddDropIfGroupLineMode Indicates whether the interface is grouped
into a ROADM-TU-group.
disabled - The interface is not grouped into
a ROADM-TU-group.
enabled - The interf… | column | Enumeration | .1.3.6.1.4.1.8708.2.31.2.2.1.1.29 |
| roadmAddDropIfDescr User configurable label.
This attribute can be written via SNMP. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.3 |
| roadmAddDropIfNoOfConnectedChannels The number of channels connected to this port. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.31.2.2.1.1.30 |
| roadmAddDropIfViewChannelList Shows a list of all channels connected to this port.
This attribute is only used for presentation. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.31 |
| roadmAddDropIfConnectedChannelMask Shows a list of all channels connected to this port.
Format:
'<start-freq>:<spacing>:<bit-mask>'
This is the actual storage of the cross-connect i… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.32 |
| roadmAddDropIfAddChannelCommand Specify that a new channel shall be added
from this port. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.33 |
| roadmAddDropIfUnlinkChannelCommand Specify that a channel shall be removed
(disconnected) from this port. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.34 |
| roadmAddDropIfUnlinkAllChannelsCommand Confirm that all channels shall be removed
(disconnected) from this port. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.35 |
| roadmAddDropIfSetAttenuationCommand Set a fixed attenuation for channels connected
to this port. Control-loop regulated channels
are not affected.
Range: 0 to 15.0 dB | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.36 |
| roadmAddDropIfAdjustAttenuationDeltaCommand Increase or decrease the attenuation for channels
connected to this port. Control-loop regulated channels
are not affected.
The resulting attenuation will always be within the al… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.37 |
| roadmAddDropIfConnectChannelCmd This is a 'write-only' parameter that the
TNM can use to cross-connect a new channel.
When you read the parameter, you will get
an integer value that is incremented… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.31.2.2.1.1.38 |
| roadmAddDropIfDisconnectChannelCmd This is a 'write-only' parameter that the
TNM can use to disconnect a channel.
When you read the parameter, you will get
an integer value that is incremented each t… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.31.2.2.1.1.39 |
| roadmAddDropIfSubrack The number of the subrack where the interface
is located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.31.2.2.1.1.4 |
| roadmAddDropIfAddAllChannelCommand All available channels shall be added
from this port. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.41 |
| roadmAddDropIfSetAdminStatusCommand Set administrative status for channels that are
connected to this port.
Control-loop regulated channels are not affected. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.31.2.2.1.1.42 |
| roadmAddDropIfSpacingHwCapability The hardware capability of the interface used when deciding whether
an interface is compatible with another interface and thereby can
form a ROADM-ROADM group
spac… | column | Enumeration | .1.3.6.1.4.1.8708.2.31.2.2.1.1.43 |
| roadmAddDropIfSlot The number of the slot where the interface is
located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.31.2.2.1.1.5 |
| roadmAddDropIfTxPort The number of the port where the TX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.31.2.2.1.1.6 |
| roadmAddDropIfRxPort The number of the port where the RX-side of
the interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.31.2.2.1.1.7 |
| roadmAddDropIfInvPhysIndexOrZero The row in the invPhysTable for this interface.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.31.2.2.1.1.8 |
| roadmAddDropIfAdminStatus The administrative state for the interface.
down - The interface should be inactive (i.e dark
mode).
service - The interface is activated but alarms
… | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.31.2.2.1.1.9 |