muxIfOHTransparency
LUM-MUX-MIB ·
.1.3.6.1.4.1.8708.2.13.2.2.1.1.33
Object
column
r/w
Enumeration
The 'OH Transparency' setting shall be set to 'off' for
standard SDH/SONET mode.
When set to 'on', the following tributary OH-bytes are
transparently transported:
E1, E2, F1, D1-D3, D4-D12, K1, K2
The following are always terminated:
J0, B1, B2, M1 and S1.
Context
- MIB
- LUM-MUX-MIB
- OID
.1.3.6.1.4.1.8708.2.13.2.2.1.1.33- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- muxIfEntry
- Table
- muxIfTable
- Siblings
- 47
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | off |
2 | on |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| muxIfIndex An arbitrary index assigned to each if entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.1 |
| muxIfPowerLevelHighThreshold The upper threshold for received power level in
units of 0.1 dBm. | column | Integer32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.10 |
| muxIfPowerLevelLowThreshold The lower threshold for received power level in
units of 0.1 dBm. | column | Integer32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.11 |
| muxIfAdminStatus The administrative state for the interface.
down - The interface should be inactive.
service - The interface is activated but alarms
are suppressed. … | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.12 |
| muxIfOperStatus The operational state for the interface.
notPresent - The physical resources are not
available.
down - The interface is de-activated or the are
fault… | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.13 |
| muxIfLossOfSignal Loss of signal.
Applicable for all signal formats.
A(ctivation): Active loss of signal HW indication.
D(e-activation): Inactive loss of signal HW
ind… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.14 |
| muxIfReceivedPowerHigh Received power level is too high.
Applicable for all signal formats.
A: The received power level exceeds the
the built-in overload threshold.
D: The … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.15 |
| muxIfReceivedPowerLow Received power level low threshold exceeded.
Applicable for all signal formats.
A: The received power level is below the
associated threshold.
D: The… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.16 |
| muxIfBitrateMismatch Bitrate mismatch (Other).
Applicable for other signal formats.
D: The interface is unable to lock to the
inserted signal.
D: The interface is able to… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.17 |
| muxIfLaserBias Measures laser bias current value in tenths
of mA (0.1 mA). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.18 |
| muxIfLaserBiasThreshold Sets the threshold for the laser bias alarm.
in percentage relative to the value set during
production. The preset value is 100%. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.19 |
| muxIfName The management name of the interface,
for example 'muxi:1:2:1', where the first number
indicates sub-rack, the second slot number and
the third is the port number. | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.13.2.2.1.1.2 |
| muxIfJ0PathTrace deprecated Note: This attribute is deprecated!
The recevied J0 path trace string.
Applicable for SDH/Sonet signal formats. | column | OctetString | .1.3.6.1.4.1.8708.2.13.2.2.1.1.20 |
| muxIfAlarmIndicationSignal Alarm indication signal.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.21 |
| muxIfLossOfFrame Loss of frame.
Applicable for SDH/Sonet signal formats.
A: SDH frame can not be located.
D: SDH frame is located. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.22 |
| muxIfLaserStatus The operational state of the TX-side laser.
off - The laser is turned off.
on - The laser is turned on. | column | Enumeration | .1.3.6.1.4.1.8708.2.13.2.2.1.1.23 |
| muxIfTxDirection The direction of the transmitted signal.
undefined - Unknown/Dont care
toWest - The transmitted signal is sent to west.
toEast - The t… | column | MuxTxDirection | .1.3.6.1.4.1.8708.2.13.2.2.1.1.24 |
| muxIfExpectedTxLambda The expected frequency given in hundreds of
GHz (0.01 GHz).
This attribute can be written via SNMP. | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.13.2.2.1.1.25 |
| muxIfTxLambda The transmitted frequency given in hundreds
of GHz (0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.13.2.2.1.1.26 |
| muxIfTraceIntrusionMode Indicates wether the trace identifier should
be inserted in the transmitted signal.
disabled - The trace identifier is taken from
the recevied signal if possible.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.13.2.2.1.1.27 |
| muxIfTraceTransmitted The trace identifier to be transmitted from
this interface.
Set to empty string for default value:
<IP address>:<subrack>:<slot>:<port>
… | column | OctetString | .1.3.6.1.4.1.8708.2.13.2.2.1.1.28 |
| muxIfTraceReceived The received trace identifier for this interface. | column | OctetString | .1.3.6.1.4.1.8708.2.13.2.2.1.1.29 |
| muxIfDescr User configurable label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.13.2.2.1.1.3 |
| muxIfTraceExpected Trace identifier used for matching against
the received trace identifier. | column | OctetString | .1.3.6.1.4.1.8708.2.13.2.2.1.1.30 |
| muxIfTraceAlarmMode Controls if the trace identifier mismatch alarm
should be raised.
disabled - The alarm is disabled.
enabled - The alarm is raised if expected trace
i… | column | Enumeration | .1.3.6.1.4.1.8708.2.13.2.2.1.1.31 |
| muxIfTraceMismatch Indicates if the expected trace identifier
differs from the received trace identifier.
A: The received trace identifier differs from
the expected trace identifier.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.32 |
| muxIfSuppressRemoteAlarms Suppress AIS and RDI in the alarm list. The fault status on
the port object can, however, be seen.
disabled - alarms are not suppressed.
enabled - al… | column | Enumeration | .1.3.6.1.4.1.8708.2.13.2.2.1.1.34 |
| muxIfHighSpeedMin The minmum speed in units of 1,000,000 bits (Mb)
per second. If this object reports a value of 'n'
then the speed of the interface is somewhere in
the range of 'n-500,000' to 'n+4… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.35 |
| muxIfHighSpeedMax The maximum speed in units of 1,000,000 bits per
second. If this object reports a value of 'n'
then the speed of the interface is somewhere in
the range of 'n-500,000' to 'n+499,9… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.36 |
| muxIfTrxCodeMismatch The inserted transceiver does not have a legal
manufacturer code.
A: A transceiver with illegal code is inserted.
D: The transceiver with illegal cod… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.37 |
| muxIfTrxBitrateUnavailable The inserted transceiver does not support the requested
bit rate.
A: A transceiver with other supported bit rate than
the requested bit rate is inserted.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.38 |
| muxIfTrxMissing An expected transceiver is missing.
A: An expected transceiver is missing.
D: The missing transceiver is inserted. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.39 |
| muxIfSubrack The number of the subrack where the interface
is located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.13.2.2.1.1.4 |
| muxIfTrxClass String that describes the transceiver class. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.13.2.2.1.1.40 |
| muxIfTransmitterFailed The transceiver HW has detected a failure
in the transmitter part.
A: The transmitter has failed
D: The transmitter is OK again | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.41 |
| muxIfUnexpectedFrequency The actual frequency does not match the
pre-configured frequency.
A pre-configured frequency of '0' matches
all actual frequencies.
A: The configured… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.42 |
| muxIfIllegalFrequency The frequency supported by the transceiver is not
recognized by the system.
A: Invalid or unknown frequency information is
detected in the (pluggable) transceive… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.13.2.2.1.1.43 |
| muxIfReceiverSensitivity The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.44 |
| muxIfPowerLevelLowRelativeThreshold The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity. | column | Integer32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.45 |
| muxIfObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.13.2.2.1.1.46 |
| muxIfTxPowerLevel The transmitted power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.47 |
| muxIfLaserTempActual The actual laser temperature in units of
0.1 degrees centigrade. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.48 |
| muxIfSlot The number of the slot where the interface is
located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.13.2.2.1.1.5 |
| muxIfTxPort The number of the port where the TX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.13.2.2.1.1.6 |
| muxIfRxPort The number of the port where the RX-side of
the interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.13.2.2.1.1.7 |
| muxIfInvPhysIndexOrZero The row in the invPhysTable for this interface.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.8 |
| muxIfPowerLevel The received power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.13.2.2.1.1.9 |