ls1InfoAdminNetIntType
LIGHTSTREAM-MIB ·
.1.3.6.1.4.1.711.2.1.4.1.1.10
Object
column
mandatory
r/w
Enumeration
Administrative or desired Network Interface Type for DCE, DTE, or DCE with local tt loopback. This last option provides the ability to interface to DTE devices which are unable to return the tt signal as required for full V.35 standard compliance.
Context
- MIB
- LIGHTSTREAM-MIB
- OID
.1.3.6.1.4.1.711.2.1.4.1.1.10- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- ls1InfoEntry
- Table
- ls1InfoTable
- Siblings
- 25
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | dce |
2 | dte |
3 | dceTTloop |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ls1InfoIfIndex mandatory This is the ifIndex value of the corresponding
ifEntry. See comments above. | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.1 |
| ls1InfoOperModemState mandatory Operational Status of certain modem signals. A bitmask
which gives the current state of certain modmem signals
is returned. If the Port is configured as a DTE, bit 0
will be DCD… | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.13 |
| ls1InfoOperProtocol mandatory Operational higher level protocol stack to support
on this port. | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.15 |
| ls1InfoAdminProtocol mandatory Administratively desired higher level protocol stack
to support on this port. | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.16 |
| ls1InfoType mandatory Level 1 interface type used for this port | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.2 |
| ls1InfoOperControlBandwidthSize mandatory The current operation value of the control bandwidth
size for this port. This is a scaling factor. This
value is multiplied by ls1InfoOperRcvBaudRate and the
result divided by… | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.21 |
| ls1InfoAdminControlBandwidthSize mandatory The current administratively desired value of the
control bandwidth size for this port. Setting the
trigger variable ls1InfoAdimOperTrigger will cause
this value to become the ope… | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.22 |
| ls1InfoOperDataBandwidthSize mandatory The current operation value of the data bandwidth
size for this port. This is a scaling factor. This
value is multiplied by ls1InfoOperRcvBaudRate and the
result divided by 10… | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.23 |
| ls1InfoAdminDataBandwidthSize mandatory The current administratively desired value of the
data bandwidth size for this port. Setting the
trigger variable ls1InfoAdimOperTrigger will cause
this value to become the operat… | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.24 |
| ls1InfoOperLoopMode mandatory Operational loop mode for this port:
none, internal, external, or remote | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.25 |
| ls1InfoAdminLoopMode mandatory Administrative or desired loop mode for this
port: none, internal, external, or remote | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.26 |
| ls1InfoLcAutoEnable mandatory State of the LC auto-enable flag for this port. If
enabled the port will be enable at LC boot time.
If disabled the port will remain disabled until
configured and started by th… | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.27 |
| ls1InfoLcDebugLevel mandatory Value of the LC debug level variable for this port.
This parameter is set in the LC EEPROM by portctl. | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.28 |
| ls1InfoDataCellCapacity mandatory The portion of this port's capacity in cells that
is allocated for data traffic. | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.29 |
| ls1InfoOperCsuType mandatory Identifier of operational CSU Interface | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.3 |
| ls1InfoDataCellAvailable mandatory The portion of this port's capacity in cells that
is available for data traffic. This variable
is adjusted for the bandwidth consumed by VCs
created using this port. It does n… | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.30 |
| ls1InfoMeasuredBaudRate mandatory This is the line rate as measured from the line card. | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.31 |
| ls1InfoLinkUtilization mandatory This is an estimated utilization on the link. | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.32 |
| ls1InfoAdminCsuType mandatory Identifier of administartively specified CSU Interface | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.4 |
| ls1InfoOperRcvBaudRate mandatory Operation receive baud rate | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.5 |
| ls1InfoAdminRcvBaudRate mandatory Adminsitratively desired receive baud rate | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.6 |
| ls1InfoOperXmitBaudRate mandatory Operation transmit baud rate. | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.7 |
| ls1InfoAdminXmitBaudRate mandatory Admistratively desired transmission baud rate | column | Integer32 | .1.3.6.1.4.1.711.2.1.4.1.1.8 |
| ls1InfoOperNetIntType mandatory Operational network Interface Type for this port:
DCE, DTE, or DCE with local tt loopback. This last
option provides the ability to interface to DTE
devices which are unable to r… | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.9 |
| ls1InfoAdminOperTrigger mandatory When proper commands written to this variable the
LCC attempts to change the state of the port such
that the oper status reflects the desired admin status. | column | Enumeration | .1.3.6.1.4.1.711.2.1.4.1.1.99 |