vlagCurCfgHlthchkKeepaliveAttempts

LENOVO-GbTOR-G8052-RS-MIB · .1.3.6.1.4.1.26543.2.7.7.2.1.18.20

Object

scalar Integer32

Number of keepalive attempts made before declaring 
peer is down. Within this time, atleast one of the 
keepalive message should have been received from the peer.

Context

MIB: LENOVO-GbTOR-G8052-RS-MIB
OID: .1.3.6.1.4.1.26543.2.7.7.2.1.18.20
Type: scalar
Access: readonly
Status: current
Parent: vlagCfg
Siblings: 28

Syntax

Integer32

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects

Object	Type	Syntax	OID
vlagIslCfg	node	-	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.1`
vlagCurCfgHlthchkPeerIp The current Health check Peer ip4 address.	scalar	SNMPv2-SMIIpAddress	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.10`
vlagNewCfgHlthchkPeerIp The New Health check Peer ip4 address.	scalar	SNMPv2-SMIIpAddress	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.11`
vlagCurCfgTierId Current vLAG Tier ID	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.12`
vlagNewCfgTierId This object is used to change the vLAG Tier ID of this switch. vLAG consist of 2 vLAG peer switches connected by ISL link, the system formed by the switches is referred to as a vL…	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.13`
vlagCurCfgStartupDelayInterval Current vLAG Startup delay interval	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.14`
vlagNewCfgStartupDelayInterval This object is used to change the vLAG startup Delay Timer interval. The Timer is used to prevent traffic lost for the vLAG ports may be up before the ISL is up. The Timer is st- …	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.15`
vlagCurCfgGlobalEnable Current vLAG global status on switch.	scalar	Enumeration	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.16`
vlagNewCfgGlobalEnable Set true to enable vLAG globally or Set false to disable vLAG globally on switch.	scalar	Enumeration	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.17`
vlagCurCfgHlthchkConnectRetryInterval In case of healtcheck TCP connection can not be established, interval at which the retry attempt will be made to connect to the peer.	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.18`
vlagNewCfgHlthchkConnectRetryInterval In case of healtcheck TCP connection can not be established, interval at which the retry attempt will be made to connect to the peer.	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.19`
vlagNewCfgHlthchkKeepaliveAttempts Number of keepalive attempts made before declaring peer is down.Within this time, atleast one of the keepalive message should have been received from the peer.	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.21`
vlagCurCfgHlthchkKeepaliveInterval Interval between keepalives sent over healthcheck TCP session to keep the session alive.	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.22`
vlagNewCfgHlthchkKeepaliveInterval Interval between keepalives sent over healthcheck TCP session to keep the session alive.	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.23`
vlagCurCfgAutoRecoveryInterval Current vLAG Auto Recovery interval	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.24`
vlagNewCfgAutoRecoveryInterval This object is used to change the vLAG Auto Recovery Timer interval. The Timer is used to prevent all vlag ports stay in ErrDisabled state when booting two vLAG switches but one …	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.25`
vlagCurCfgHlthchkPeerIpv6 The current Health check Peer ipv6 address.	scalar	OctetString	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.26`
vlagNewCfgHlthchkPeerIpv6 The New Health check Peer ipv6 address.	scalar	OctetString	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.27`
vlagCurCfgVrrpActive Current VLAG VRRP active mode configuration. If enabled(1), the switch will always forward L3 traffic in all vLAG-enabled VRRP domains. If disabled(2), the switch will forward L3 …	scalar	Enumeration	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.28`
vlagNewCfgVrrpActive Set to enabled(1) to configure the switch to always forward L3 traffic in all vLAG-enabled VRRP domains. Set to disabled(2) to configure the switch to forward L3 traffic in a VRRP…	scalar	Enumeration	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.29`
vlagCurCfgFdbRefresh Current VLAG FDB refresh mode configuration. If enabled(1), the switch will refresh the synchronized FDB periodically to prevent the entries from aging. If disabled(2), the switc…	scalar	Enumeration	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.30`
vlagNewCfgFdbRefresh Set to enabled(1) to configure the switch to refresh the synchronized FDB periodically to prevent the entries from aging. Set to disabled(2) to disable the refresh.	scalar	Enumeration	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.31`
vlagCurCfgSwitchPriority Current vLAG switch priority	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.4`
vlagNewCfgSwitchPriority This object is used to change the vLAG priority of this switch.	scalar	Integer32	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.5`
vlagCurCfgTrunkTable A table of objects of the vLAG groups configured in this switch.	table	-	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.6`
vlagNewCfgTrunkTable A table of objects of the vLAG groups configured in this switch.	table	-	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.7`
vlagCurCfgLacpTable A table of objects of the vLAG groups configured in this switch.	table	-	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.8`
vlagNewCfgLacpTable A table of objects of the vLAG groups configured in this switch.	table	-	`.1.3.6.1.4.1.26543.2.7.7.2.1.18.9`