vlagCurCfgSwitchPriority

LENOVO-GbTOR-10G-L2L3-MIB · .1.3.6.1.4.1.26543.2.7.4.2.1.18.4
MIB view Table view

Object

scalar Integer32 
Current vLAG switch priority

Context

MIB
LENOVO-GbTOR-10G-L2L3-MIB
OID
.1.3.6.1.4.1.26543.2.7.4.2.1.18.4
Type
scalar
Access
readonly
Status
current
Parent
vlagCfg
Siblings
30

Syntax

Integer32

Values & Constraints

Enumerated Values
1enabled
2disabled

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
vlagIslCfgnode-.1.3.6.1.4.1.26543.2.7.4.2.1.18.1
vlagCurCfgHlthchkPeerIp
The current Health check Peer ip4 address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.26543.2.7.4.2.1.18.10
vlagNewCfgHlthchkPeerIp
The New Health check Peer ip4 address.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.26543.2.7.4.2.1.18.11
vlagCurCfgTierId
Current vLAG Tier ID
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.12
vlagNewCfgTierId
This object is used to change the vLAG Tier ID of this switch. vLAG consist of 2 vLAG peer switches connected by ISL link, the system formed by the switches is referred to as a vL…
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.13
vlagCurCfgStartupDelayInterval
Current vLAG Startup delay interval
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.14
vlagNewCfgStartupDelayInterval
This object is used to change the vLAG startup Delay Timer interval. The Timer is used to prevent traffic lost for the vLAG ports may be up before the ISL is up. The Timer is st- …
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.15
vlagCurCfgGlobalEnable
Current vLAG global status on switch.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.4.2.1.18.16
vlagNewCfgGlobalEnable
Set true to enable vLAG globally or Set false to disable vLAG globally on switch.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.4.2.1.18.17
vlagCurCfgHlthchkConnectRetryInterval
In case of healtcheck TCP connection can not be established, interval at which the retry attempt will be made to connect to the peer.
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.18
vlagNewCfgHlthchkConnectRetryInterval
In case of healtcheck TCP connection can not be established, interval at which the retry attempt will be made to connect to the peer.
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.19
vlagCurCfgHlthchkKeepaliveAttempts
Number of keepalive attempts made before declaring peer is down. Within this time, atleast one of the keepalive message should have been received from the peer.
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.20
vlagNewCfgHlthchkKeepaliveAttempts
Number of keepalive attempts made before declaring peer is down.Within this time, atleast one of the keepalive message should have been received from the peer.
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.21
vlagCurCfgHlthchkKeepaliveInterval
Interval between keepalives sent over healthcheck TCP session to keep the session alive.
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.22
vlagNewCfgHlthchkKeepaliveInterval
Interval between keepalives sent over healthcheck TCP session to keep the session alive.
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.23
vlagCurCfgAutoRecoveryInterval
Current vLAG Auto Recovery interval
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.24
vlagNewCfgAutoRecoveryInterval
This object is used to change the vLAG Auto Recovery Timer interval. The Timer is used to prevent all vlag ports stay in ErrDisabled state when booting two vLAG switches but one …
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.25
vlagCurCfgHlthchkPeerIpv6
The current Health check Peer ipv6 address.
scalarOctetString.1.3.6.1.4.1.26543.2.7.4.2.1.18.26
vlagNewCfgHlthchkPeerIpv6
The New Health check Peer ipv6 address.
scalarOctetString.1.3.6.1.4.1.26543.2.7.4.2.1.18.27
vlagCurCfgVrrpActive
Current VLAG VRRP active mode configuration. If enabled(1), the switch will always forward L3 traffic in all vLAG-enabled VRRP domains. If disabled(2), the switch will forward L3 …
scalarEnumeration.1.3.6.1.4.1.26543.2.7.4.2.1.18.28
vlagNewCfgVrrpActive
Set to enabled(1) to configure the switch to always forward L3 traffic in all vLAG-enabled VRRP domains. Set to disabled(2) to configure the switch to forward L3 traffic in a VRRP…
scalarEnumeration.1.3.6.1.4.1.26543.2.7.4.2.1.18.29
vlagCurCfgFdbRefresh
Current VLAG FDB refresh mode configuration. If enabled(1), the switch will refresh the synchronized FDB periodically to prevent the entries from aging. If disabled(2), the switc…
scalarEnumeration.1.3.6.1.4.1.26543.2.7.4.2.1.18.30
vlagNewCfgFdbRefresh
Set to enabled(1) to configure the switch to refresh the synchronized FDB periodically to prevent the entries from aging. Set to disabled(2) to disable the refresh.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.4.2.1.18.31
vlagCurCfgPeerGateway
Current peer gateway configuration. If enabled(1), the vLAG switch will act as the active gateway for packets that are addressed to the router MAC address of the vLAG peer.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.4.2.1.18.32
vlagNewCfgPeerGateway
Set enabled(1) to configure the vLAG switch to act as the active gateway for packets that are addressed to the router MAC address of the vLAG peer. Set to disabled(2) to configure…
scalarEnumeration.1.3.6.1.4.1.26543.2.7.4.2.1.18.33
vlagNewCfgSwitchPriority
This object is used to change the vLAG priority of this switch.
scalarInteger32.1.3.6.1.4.1.26543.2.7.4.2.1.18.5
vlagCurCfgTrunkTable
A table of objects of the vLAG groups configured in this switch.
table-.1.3.6.1.4.1.26543.2.7.4.2.1.18.6
vlagNewCfgTrunkTable
A table of objects of the vLAG groups configured in this switch.
table-.1.3.6.1.4.1.26543.2.7.4.2.1.18.7
vlagCurCfgLacpTable
A table of objects of the vLAG groups configured in this switch.
table-.1.3.6.1.4.1.26543.2.7.4.2.1.18.8
vlagNewCfgLacpTable
A table of objects of the vLAG groups configured in this switch.
table-.1.3.6.1.4.1.26543.2.7.4.2.1.18.9