juniV35IfClockRate
Juniper-V35-MIB ·
.1.3.6.1.4.1.4874.2.2.59.1.2.1.4
Object
The clock rate setting in hertz for this X.21/V.35 interface. Only the
following values are valid: 1200, 2400, 4800, 9600, 19200, 38400, 56000,
64000, 128000, 1024000, 1536000, 2048000, 3072000, 4096000, 4915200,
6144000, and 8192000. If a value other than one of the predefined
values is set, then the closest matching value is used.
The clock rate parameter is only meaningful when the interface is in DCE
mode. When the interface is in DTE mode, the value is simply ignored.
Context
- MIB
- Juniper-V35-MIB
- OID
.1.3.6.1.4.1.4874.2.2.59.1.2.1.4- Type
- column
- Access
- readwrite
- Status
- current
- Units
- hertz
- Parent
- juniV35IfEntry
- Table
- juniV35IfTable
- Siblings
- 7
Syntax
hertz SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| juniV35IfIndex The ifIndex of the X.21/V.35 interface. It has the same value as the
juniHdlcIfIndex for the common interface. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.4874.2.2.59.1.2.1.1 |
| juniV35IfType Read only parameter of interface type X.21/V.35. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.59.1.2.1.2 |
| juniV35IfMode Read only parameter of interface mode of interface X.21/V.35 Data
Terminating Equipment(DTE)/Data Communication Equipment(DCE). | column | Enumeration | .1.3.6.1.4.1.4874.2.2.59.1.2.1.3 |
| juniV35IfNrzEncoding The non-return-to-zero (NRZ) encoding for X.21/V.35 interface.
Inverted encoding is provided with NRZI-encoding command, which is
non-return-to-zero inverted (NRZI) encoding. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.59.1.2.1.5 |
| juniV35IfTxClock There is an option of inverting the transmit clock signal for X.21/V.35
interface. Inverting the tranmit clock is used to compensate for skews
between the clock and data when tra… | column | Enumeration | .1.3.6.1.4.1.4874.2.2.59.1.2.1.6 |
| juniV35IfIgnoreDcd When in X.21/V.35 DTE mode we have the capability of ignoring the DCD
signal in determining whether or not an interface is up. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.59.1.2.1.7 |
| juniV35IfLoopback Loopback interface is configured (or not) for X.21/V.35 interface | column | Enumeration | .1.3.6.1.4.1.4874.2.2.59.1.2.1.8 |